From: Tobias Kaminsky <tobiaskaminsky@web.de>
To: linux-media@vger.kernel.org
Subject: Two WinTV1110 in one PC not working, single works
Date: Tue, 2 Jun 2009 15:57:27 +0200 [thread overview]
Message-ID: <200906021557.27614.tobiaskaminsky@web.de> (raw)
Hello,
I have two WinTX1110 installed in one PC:
04:03.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135
Video Broadcast Decoder (rev d1)
04:04.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135
Video Broadcast Decoder (rev d1)
The first card is working fine.
But the second fails to load the firmware:
[ 215.424008] tda1004x: found firmware revision 0 -- invalid
[ 215.424014] tda1004x: firmware upload failed
I have tried both cards alone in the pc and they are working, but together
not.
The "first" card says this:
[ 204.217357] tda1004x: found firmware revision 20 -- ok
So the current status is that only one is working and I do not know what I can
change.
The Firmware:
-rw-r--r-- 1 root 24478 2008-10-27 06:33 /lib/firmware/dvb-fe-tda10046.fw
What else informations do you need?
Thank you very much!
Tobias Kaminsky
dmesg:
[ 12.593302] Linux video capture interface: v2.00
[ 12.903476] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 12.904699] saa7134 0000:04:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ
16
[ 12.904706] saa7133[0]: found at 0000:04:03.0, rev: 209, irq: 16, latency:
32, mmio: 0xfdaff000
[ 12.904714] saa7133[0]: subsystem: 0070:6701, board: Hauppauge WinTV-
HVR1110 DVB-T/Hybrid [card=104,autodetected]
[ 12.904726] saa7133[0]: board init: gpio is 6400000
[ 13.063355] saa7133[0]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43 a9 1c
55 d2 b2 92
[ 13.063366] saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff
[ 13.063375] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 aa ff
ff ff ff
[ 13.063383] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 13.063392] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff
ff ff
[ 13.063401] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 13.063409] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 13.063418] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 13.063426] saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 6f 78 0e f0
73 05 29 00
[ 13.063435] saa7133[0]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48 89 72
07 70 73 09
[ 13.063444] saa7133[0]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72 0e 01
72 0f 03 72
[ 13.063452] saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 79 49 00 00 00 00 00
00 00 00 00
[ 13.063461] saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 13.063469] saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 13.063478] saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 13.063486] saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 13.364324] tuner' 1-004b: chip found @ 0x96 (saa7133[0])
[ 13.367371] tveeprom 1-0050: Hauppauge model 67019, rev B4B4, serial#
948335
[ 13.367375] tveeprom 1-0050: MAC address is 00-0D-FE-0E-78-6F
[ 13.367378] tveeprom 1-0050: tuner model is Philips 8275A (idx 114, type 4)
[ 13.367381] tveeprom 1-0050: TV standards PAL(B/G) NTSC(M) PAL(I)
SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[ 13.367385] tveeprom 1-0050: audio processor is SAA7131 (idx 41)
[ 13.367387] tveeprom 1-0050: decoder processor is SAA7131 (idx 35)
[ 13.367390] tveeprom 1-0050: has radio, has IR receiver, has IR transmitter
[ 13.367392] saa7133[0]: hauppauge eeprom: model=67019
[ 13.456094] tda829x 1-004b: setting tuner address to 61
[ 13.556076] tda829x 1-004b: type set to tda8290+75a
[ 17.422485] saa7133[0]: registered device video0 [v4l2]
[ 17.422789] saa7133[0]: registered device vbi0
[ 17.423087] saa7133[0]: registered device radio0
[ 17.484044] saa7134 0000:04:04.0: PCI INT A -> GSI 17 (level, low) -> IRQ
17
[ 17.484052] saa7133[1]: found at 0000:04:04.0, rev: 209, irq: 17, latency:
32, mmio: 0xfdafe000
[ 17.484060] saa7133[1]: subsystem: 0070:6701, board: Hauppauge WinTV-
HVR1110 DVB-T/Hybrid [card=104,autodetected]
[ 17.484072] saa7133[1]: board init: gpio is 6400000
[ 17.628082] tuner' 2-004b: chip found @ 0x96 (saa7133[1])
[ 17.676014] saa7133[1]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43 a9 1c
55 d2 b2 92
[ 17.676024] saa7133[1]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff
[ 17.676033] saa7133[1]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 aa ff
ff ff ff
[ 17.676042] saa7133[1]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 17.676051] saa7133[1]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff
ff ff
[ 17.676059] saa7133[1]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 17.676068] saa7133[1]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 17.676077] saa7133[1]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 17.676085] saa7133[1]: i2c eeprom 80: 84 09 00 04 20 77 00 40 59 4b 4f f0
73 05 29 00
[ 17.676094] saa7133[1]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48 89 72
07 70 73 09
[ 17.676103] saa7133[1]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72 0e 01
72 0f 03 72
[ 17.676111] saa7133[1]: i2c eeprom b0: 10 01 72 11 ff 79 4b 00 00 00 00 00
00 00 00 00
[ 17.676120] saa7133[1]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 17.676128] saa7133[1]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 17.676137] saa7133[1]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 17.676146] saa7133[1]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00
[ 17.685388] tveeprom 2-0050: Hauppauge model 67019, rev B4B4, serial#
5196633
[ 17.685392] tveeprom 2-0050: MAC address is 00-0D-FE-4F-4B-59
[ 17.685395] tveeprom 2-0050: tuner model is Philips 8275A (idx 114, type 4)
[ 17.685398] tveeprom 2-0050: TV standards PAL(B/G) NTSC(M) PAL(I)
SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[ 17.685402] tveeprom 2-0050: audio processor is SAA7131 (idx 41)
[ 17.685404] tveeprom 2-0050: decoder processor is SAA7131 (idx 35)
[ 17.685407] tveeprom 2-0050: has radio, has IR receiver, has IR transmitter
[ 17.685410] saa7133[1]: hauppauge eeprom: model=67019
[ 17.772015] tda829x 2-004b: setting tuner address to 61
[ 17.836014] tda829x 2-004b: type set to tda8290+75a
[ 21.692599] saa7133[1]: registered device video1 [v4l2]
[ 21.692915] saa7133[1]: registered device vbi1
[ 21.693223] saa7133[1]: registered device radio1
[ 21.777372] saa7134 ALSA driver for DMA sound loaded
[ 21.789059] saa7133[0]/alsa: saa7133[0] at 0xfdaff000 irq 16 registered as
card -2
[ 21.789550] saa7133[1]/alsa: saa7133[1] at 0xfdafe000 irq 17 registered as
card -1
[ 21.938693] DVB: registering new adapter (saa7133[0])
[ 21.938698] DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
next reply other threads:[~2009-06-02 13:58 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-06-02 13:57 Tobias Kaminsky [this message]
2009-06-02 14:32 ` Two WinTV1110 in one PC not working, single works Tobias Kaminsky
2009-06-04 12:31 ` Tobias Kaminsky
2009-06-05 12:55 ` Tobias Kaminsky
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200906021557.27614.tobiaskaminsky@web.de \
--to=tobiaskaminsky@web.de \
--cc=linux-media@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox