bttv problem loading takes about several minutes

bttv problem loading takes about several minutes

[Halim Sahin]

Hi,
In the past I could use this card by typing
modprobe bttv card=34 tuner=24 gbuffers=16
Giving this command with current drivers has some problems:
1. it takes several minutes to load bttv module.
2. capturing doesn't work any more (dropped frames etc).
Tested with current v4l-dvb from hg, ubuntu 9.04, 
debian lenny.

I have a bt878  based card from leadtek.

Here is my output after loading the driver:
[ 3013.735459] bttv: driver version 0.9.17 loaded
[ 3013.735470] bttv: using 32 buffers with 16k (4 pages) each for capture
[ 3013.735542] bttv: Bt8xx card found (0).
[ 3013.735562] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32, mmio
: 0xf7800000
[ 3013.737762] bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,insm
od option]
[ 3013.737825] bttv0: gpio: en=00000000, out=00000000 in=003ff502 [init]
[ 3148.136017] bttv0: tuner type=24
[ 3148.136029] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[ 3154.536019] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[ 3160.936018] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[ 3167.351398] bttv0: registered device video0
[ 3167.351434] bttv0: registered device vbi0
[ 3167.351463] bttv0: registered device radio0
[ 3167.351485] bttv0: PLL: 28636363 => 35468950 . ok
[ 3167.364182] input: bttv IR (card=34) as /class/input/input6

Please help!
Regards
Halim


-- 
Halim Sahin
E-Mail:				
halim.sahin (at) t-online.de

Re: bttv problem loading takes about several minutes

[Trent Piepho]

On Wed, 17 Jun 2009, Halim Sahin wrote:
> Hi,
> In the past I could use this card by typing
> modprobe bttv card=34 tuner=24 gbuffers=16

What card do you actually have?  What is the PCI subsystem vendor/device
and what tuner does it actually have?

Hans, the problem might be with bttv audio probing.  This card has
needs_tvaudio set to 0, which used to mean that tvaudio would not be probed
or loaded.  But with your changes to bttv audio probing this behavior has
changed.  Now tvaudio is always loaded and probed if another audio chip
hasn't been detected.  The needs_tvaudio field is totally ignored.

> Giving this command with current drivers has some problems:
> 1. it takes several minutes to load bttv module.
> 2. capturing doesn't work any more (dropped frames etc).
> Tested with current v4l-dvb from hg, ubuntu 9.04,
> debian lenny.
>
> I have a bt878  based card from leadtek.
>
> Here is my output after loading the driver:
> [ 3013.735459] bttv: driver version 0.9.17 loaded
> [ 3013.735470] bttv: using 32 buffers with 16k (4 pages) each for capture
> [ 3013.735542] bttv: Bt8xx card found (0).
> [ 3013.735562] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32, mmio
> : 0xf7800000
> [ 3013.737762] bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,insm
> od option]
> [ 3013.737825] bttv0: gpio: en=00000000, out=00000000 in=003ff502 [init]
> [ 3148.136017] bttv0: tuner type=24
> [ 3148.136029] bttv0: i2c: checking for MSP34xx @ 0x80... not found
> [ 3154.536019] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> [ 3160.936018] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> [ 3167.351398] bttv0: registered device video0
> [ 3167.351434] bttv0: registered device vbi0
> [ 3167.351463] bttv0: registered device radio0
> [ 3167.351485] bttv0: PLL: 28636363 => 35468950 . ok
> [ 3167.364182] input: bttv IR (card=34) as /class/input/input6
>
> Please help!
> Regards
> Halim
>
>
> --
> Halim Sahin
> E-Mail:
> halim.sahin (at) t-online.de
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>

Re: bttv problem loading takes about several minutes

[Halim Sahin]

Hi,
The card is a
winfast tv 2000 xp rm edition
lspci -vvv says:

00:0b.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (4000ns min, 10000ns max)
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at f7800000 (32-bit, prefetchable) [size=4K]
	Capabilities: [44] Vital Product Data <?>
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: bttv
	Kernel modules: bttv

00:0b.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (1000ns min, 63750ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at f7000000 (32-bit, prefetchable) [size=4K]
	Capabilities: [44] Vital Product Data <?>
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-


HTH.
Halim

-- 
Halim Sahin
E-Mail:				
halim.sahin (at) t-online.de

Re: bttv problem loading takes about several minutes

[Hans Verkuil]

On Wednesday 17 June 2009 19:11:23 Trent Piepho wrote:
> On Wed, 17 Jun 2009, Halim Sahin wrote:
> > Hi,
> > In the past I could use this card by typing
> > modprobe bttv card=34 tuner=24 gbuffers=16
>
> What card do you actually have?  What is the PCI subsystem vendor/device
> and what tuner does it actually have?
>
> Hans, the problem might be with bttv audio probing.  This card has
> needs_tvaudio set to 0, which used to mean that tvaudio would not be
> probed or loaded.  But with your changes to bttv audio probing this
> behavior has changed.  Now tvaudio is always loaded and probed if another
> audio chip hasn't been detected.  The needs_tvaudio field is totally
> ignored.

The log is from bttv version 0.9.17. The new code is only present in version 
0.9.18. So this is definitely not related to any of my changes.

The text "bttv0: gpio: en=00000000, out=00000000 in=003ff502 [init]" comes 
from the call to bttv_gpio_tracking in bttv_probe, then the next 
text "bttv0: tuner type=24" comes from early in bttv_init_card2, before any 
i2c modules have been loaded.

The code in bttv_probe (bttv-driver.c) does this:

        if (bttv_verbose)
                bttv_gpio_tracking(btv,"init");

        /* needs to be done before i2c is registered */
        bttv_init_card1(btv);

        /* register i2c + gpio */
        init_bttv_i2c(btv);

        /* some card-specific stuff (needs working i2c) */
        bttv_init_card2(btv);

So it looks like it can be either bttv_init_card1 or init_bttv_i2c that is 
causing the delay.

Halim, can you try to put some printk() statements in between the calls 
above to see which call is taking so long? Actually, it would be nice if 
you are able to 'drill-down' as well in whatever function is causing the 
delay, since I truly don't see what might be delaying things for you.

Regards,

	Hans

>
> > Giving this command with current drivers has some problems:
> > 1. it takes several minutes to load bttv module.
> > 2. capturing doesn't work any more (dropped frames etc).
> > Tested with current v4l-dvb from hg, ubuntu 9.04,
> > debian lenny.
> >
> > I have a bt878  based card from leadtek.
> >
> > Here is my output after loading the driver:
> > [ 3013.735459] bttv: driver version 0.9.17 loaded
> > [ 3013.735470] bttv: using 32 buffers with 16k (4 pages) each for
> > capture [ 3013.735542] bttv: Bt8xx card found (0).
> > [ 3013.735562] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency:
> > 32, mmio
> >
> > : 0xf7800000
> >
> > [ 3013.737762] bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP
> > [card=34,insm od option]
> > [ 3013.737825] bttv0: gpio: en=00000000, out=00000000 in=003ff502
> > [init] [ 3148.136017] bttv0: tuner type=24
> > [ 3148.136029] bttv0: i2c: checking for MSP34xx @ 0x80... not found
> > [ 3154.536019] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> > [ 3160.936018] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> > [ 3167.351398] bttv0: registered device video0
> > [ 3167.351434] bttv0: registered device vbi0
> > [ 3167.351463] bttv0: registered device radio0
> > [ 3167.351485] bttv0: PLL: 28636363 => 35468950 . ok
> > [ 3167.364182] input: bttv IR (card=34) as /class/input/input6
> >
> > Please help!
> > Regards
> > Halim
> >
> >
> > --
> > Halim Sahin
> > E-Mail:
> > halim.sahin (at) t-online.de
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-media"
> > in the body of a message to majordomo@vger.kernel.org
> > More majordomo info at  http://vger.kernel.org/majordomo-info.html



-- 
Hans Verkuil - video4linux developer - sponsored by TANDBERG Telecom

Re: bttv problem loading takes about several minutes

[Halim Sahin]

Hi,
On Mi, Jun 17, 2009 at 10:06:26 +0200, Hans Verkuil wrote:
> The log is from bttv version 0.9.17. The new code is only present in version 
> 0.9.18. So this is definitely not related to any of my changes.
> 

Yes it's from a debian lenny kernel 2.6.26.
But I have tested latest v4l-dvb with the same result
under 2.6.28 (ubuntu 9.04).



> The code in bttv_probe (bttv-driver.c) does this:
> 
>         if (bttv_verbose)
>                 bttv_gpio_tracking(btv,"init");
> 
>         /* needs to be done before i2c is registered */
>         bttv_init_card1(btv);
> 
>         /* register i2c + gpio */
>         init_bttv_i2c(btv);
> 
>         /* some card-specific stuff (needs working i2c) */
>         bttv_init_card2(btv);
> 
> So it looks like it can be either bttv_init_card1 or init_bttv_i2c that is 
> causing the delay.
> 
> Halim, can you try to put some printk() statements in between the calls 
> above to see which call is taking so long? Actually, it would be nice if 
> you are able to 'drill-down' as well in whatever function is causing the 
> delay, since I truly don't see what might be delaying things for you.

Yes I will test  this tomorrow.

Thanks a lot!
Halim

Re: bttv problem loading takes about several minutes

[Halim Sahin]

Hi,
On Mi, Jun 17, 2009 at 10:06:26 +0200, Hans Verkuil wrote:
> The log is from bttv version 0.9.17. The new code is only present in version 
> 0.9.18. So this is definitely not related to any of my changes.
> 
> The text "bttv0: gpio: en=00000000, out=00000000 in=003ff502 [init]" comes 
> from the call to bttv_gpio_tracking in bttv_probe, then the next 
> text "bttv0: tuner type=24" comes from early in bttv_init_card2, before any 
> i2c modules have been loaded.
> 
> The code in bttv_probe (bttv-driver.c) does this:
> 
>         if (bttv_verbose)
>                 bttv_gpio_tracking(btv,"init");
> 
>         /* needs to be done before i2c is registered */
>         bttv_init_card1(btv);
> 
>         /* register i2c + gpio */
>         init_bttv_i2c(btv);
> 
>         /* some card-specific stuff (needs working i2c) */
>         bttv_init_card2(btv);
> 
> So it looks like it can be either bttv_init_card1 or init_bttv_i2c that is 
> causing the delay.
> 
> Halim, can you try to put some printk() statements in between the calls 
> above to see which call is taking so long? Actually, it would be nice if 
> you are able to 'drill-down' as well in whatever function is causing the 
> delay, since I truly don't see what might be delaying things for you.

So I have tested latest v4l-dvb from hg.
The mentioned code was changed like this:
        if (bttv_verbose)
{
printk ("bttv_gpio_tracking(bt");
                bttv_gpio_tracking(btv,"init");
}

        /* needs to be done before i2c is registered */
printk("bttv_init_card1(btv);");
printk("        bttv_init_card1(btv);");

        bttv_init_card1(btv);

        /* register i2c + gpio */
printk("        init_bttv_i2c(btv);");
        init_bttv_i2c(btv);

Result:
[ 1069.277781] bttv: driver version 0.9.18 loaded
[ 1069.277788] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 1069.277886] bttv: Bt8xx card found (0).
[ 1069.277906] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32, mmio
: 0xf7800000
[ 1069.278105] bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,insm
od option]
[ 1069.278167] bttv_gpio_tracking(bt<7>bttv0: gpio: en=00000000, out=00000000 in
=003ff502 [init]
[ 1069.278173] bttv_init_card1(btv);        bttv_init_card1(btv);        init_bt
tv_i2c(btv);<6>bttv0: tuner type=24

 
> Regards,
> 
> 	Hans
> 
> >
> > > Giving this command with current drivers has some problems:
> > > 1. it takes several minutes to load bttv module.
> > > 2. capturing doesn't work any more (dropped frames etc).
> > > Tested with current v4l-dvb from hg, ubuntu 9.04,
> > > debian lenny.
> > >
> > > I have a bt878  based card from leadtek.
> > >
> > > Here is my output after loading the driver:
> > > [ 3013.735459] bttv: driver version 0.9.17 loaded
> > > [ 3013.735470] bttv: using 32 buffers with 16k (4 pages) each for
> > > capture [ 3013.735542] bttv: Bt8xx card found (0).
> > > [ 3013.735562] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency:
> > > 32, mmio
> > >
> > > : 0xf7800000
> > >
> > > [ 3013.737762] bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP
> > > [card=34,insm od option]
> > > [ 3013.737825] bttv0: gpio: en=00000000, out=00000000 in=003ff502
> > > [init] [ 3148.136017] bttv0: tuner type=24
> > > [ 3148.136029] bttv0: i2c: checking for MSP34xx @ 0x80... not found
> > > [ 3154.536019] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> > > [ 3160.936018] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> > > [ 3167.351398] bttv0: registered device video0
> > > [ 3167.351434] bttv0: registered device vbi0
> > > [ 3167.351463] bttv0: registered device radio0
> > > [ 3167.351485] bttv0: PLL: 28636363 => 35468950 . ok
> > > [ 3167.364182] input: bttv IR (card=34) as /class/input/input6
> > >
> > > Please help!
> > > Regards
> > > Halim
> > >
> > >
> > > --
> > > Halim Sahin
> > > E-Mail:
> > > halim.sahin (at) t-online.de
> > > --
> > > To unsubscribe from this list: send the line "unsubscribe linux-media"
> > > in the body of a message to majordomo@vger.kernel.org
> > > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 
> 
> 
> -- 
> Hans Verkuil - video4linux developer - sponsored by TANDBERG Telecom
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

-- 
Halim Sahin
E-Mail:				
halim.sahin (at) t-online.de

ok more details: Re: bttv problem loading takes about several minutes

[Halim Sahin]

Hi,
sorry for the nusable output!
I found the time consuming funktion:
        bttv_init_card2(btv);
This takes about 4 min. today.
my new testcode:
        /* needs to be done before i2c is registered */
printk("linke 2:bttv_init_card1(btv);\n");

        bttv_init_card1(btv);

        /* register i2c + gpio */
printk("line 3: init_bttv_i2c(btv);\n");

        init_bttv_i2c(btv);

        /* some card-specific stuff (needs working i2c) */
printk("line4:         some card-specific stuff needs working i2c \n");
        bttv_init_card2(btv);
printk("irq init\n");

        init_irqreg(btv);

dmesg output:
[ 2282.430209] bttv: driver version 0.9.18 loaded
[ 2282.430216] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 2282.430313] bttv: Bt8xx card found (0).
[ 2282.430334] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32, mmio
: 0xf7800000
[ 2282.430777] bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,insm
od option]
[ 2282.430839] bttv_gpio_tracking(bt
[ 2282.430843] bttv0: gpio: en=00000000, out=00000000 in=003ff502 [init]
[ 2282.430845] linke 2:bttv_init_card1(btv);
[ 2282.430859] line 3: init_bttv_i2c(btv);
[ 2282.430917] line4:         some card-specific stuff needs working i2c
[ 2282.430922] bttv0: tuner type=24

Ok here is the 4 min dely and after that the following linkes were printed out:

[ 2416.836017] bttv0: audio absent, no audio device found!
[ 2416.836024] irq init
[ 2416.840551] bttv0: registered device video1
[ 2416.840684] bttv0: registered device vbi0
[ 2416.840716] bttv0: registered device radio0
[ 2416.840736] bttv0: PLL: 28636363 => 35468950 .<6>bttv0: PLL: 28636363 => 3546
8950 . ok
[ 2416.856221] input: bttv IR (card=34) as /devices/pci0000:00/0000:00:0b.0/inpu
t/input10
[ 2416.864069]  ok

Hope that helps!
Regards
Halim
-- 
Halim Sahin
E-Mail:				
halim.sahin (at) t-online.de