cx18: Need information on SECAM-D/K problem with PVR-2100

cx18: Need information on SECAM-D/K problem with PVR-2100

[Andy Walls]

Sergey,

On IRC you mentioned a problem of improper detection of SECAM-D/K with
the Leadtek PVR2100 (XC2028 and CX23418) from an RF source.

To investigate this problem on my own, I added SECAM support to the
saa7127 driver so a PVR-350 could generate a baseband SECAM signal for
me.  The good news for me is that a PVR-350 (SAA7115 video decoder) and
HVR-1600 (CX23418 integrated video decoder) card both properly
recognized the output of the PVR-350 as SECAM.  The bad news is I could
not reproduce your problem with this setup. 

Could you please do the following and send me the output from the logs?

1. Unload the cx18 module, tuner-xc2028 module, and the other tuner
modules.

2. In /etc/modprobe.conf set the following

	options tuner-xc2028 debug=1
	options tuner debug=1

3. Then

# modprobe cx18 debug=0x33         <---- info, warn, ioctl, file
# v4l2-ctl -d /dev/video0 -i 0     <---- Tuner input
# v4l2-ctl -d /dev/video0 -s 18    <---- SECAM-D/K
# v4l2-ctl -d /dev/video0 -f <freq of good channel>
# v4l2-ctl -d /dev/video0 --log-status

And send the relevant output from dmesg and /var/log/messages,
preferably to the mailing list.  I do not need the lines that begin
"cx18-0 encoder MPEG: VIDIOC_QUERYCTRL " if that makes the output
smaller.

Thanks,
Andy

Re: cx18: Need information on SECAM-D/K problem with PVR-2100

[Sergey Bolshakov]

[-- Attachment #1: Type: text/plain, Size: 549 bytes --]

>>>>> "Andy" == Andy Walls <awalls@radix.net> writes:

 > Sergey,
 > On IRC you mentioned a problem of improper detection of SECAM-D/K with
 > the Leadtek PVR2100 (XC2028 and CX23418) from an RF source.

It was some misunderstanding, i suppose, i do not have problems with
secam, i had improper detection of sound standard (and silence as
result) on pal channels. Later i've found, that fully-specified std
(pal-d instead of just pal) helps, so i can live with that.

Anyway, logs you requested (first STATUS CARD chunk for pal, second
for pal-d):


[-- Attachment #2: dmesg-cx18-pvr2100.log --]
[-- Type: text/plain, Size: 20570 bytes --]

cx18:  Start initialization, version 1.2.0
cx18-0: Initializing card 0
cx18-0: Autodetected Leadtek WinFast PVR2100 card
cx18 0000:01:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
cx18-0: cx23418 revision 01010000 (B)
cx18-0: Experimenters and photos needed for device to work well.
	To help, mail the ivtv-devel list (www.ivtvdriver.org).
IRQ 17/cx18-0: IRQF_DISABLED is not guaranteed on shared IRQs
tuner 1-0061: Setting mode_mask to 0x0e
tuner 1-0061: chip found @ 0xc2 (cx18 i2c driver #0-1)
tuner 1-0061: tuner 0x61: Tuner type absent
tuner 1-0061: Calling set_type_addr for type=71, addr=0xff, mode=0x04, config=0xffffffff
tuner 1-0061: defining GPIO callback
xc2028: Xcv2028/3028 init called!
xc2028 1-0061: creating new instance
xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner
tuner 1-0061: type set to Xceive XC3028
tuner 1-0061: cx18 i2c driver #0-1 tuner I2C addr 0xc2 with type 71 used for 0x0e
xc2028 1-0061: xc2028_set_config called
cx18-0: Registered device video0 for encoder MPEG (64 x 32 kB)
cx18-0: Registered device video32 for encoder YUV (16 x 128 kB)
cx18-0: Registered device vbi0 for encoder VBI (20 x 51984 bytes)
cx18-0: Registered device video24 for encoder PCM audio (256 x 4 kB)
cx18-0: Registered device radio0 for encoder radio
cx18-0: Initialized card: Leadtek WinFast PVR2100
cx18:  End initialization
cx18 0000:01:07.0: firmware: requesting v4l-cx23418-cpu.fw
cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
cx18 0000:01:07.0: firmware: requesting v4l-cx23418-apu.fw
cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
cx18-0: FW version: 0.0.74.0 (Release 2007/03/12)
cx18 0000:01:07.0: firmware: requesting v4l-cx23418-cpu.fw
cx18 0000:01:07.0: firmware: requesting v4l-cx23418-apu.fw
cx18 0000:01:07.0: firmware: requesting v4l-cx23418-dig.fw
cx18-0 843: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
cx18-0 843: verified load of v4l-cx23418-dig.fw firmware (16382 bytes)
tuner 1-0061: switching to v4l2
tuner 1-0061: tv freq set to 400.00
xc2028 1-0061: xc2028_set_analog_freq called
xc2028 1-0061: generic_set_freq called
xc2028 1-0061: should set frequency 400000 kHz
xc2028 1-0061: check_firmware called
xc2028 1-0061: load_all_firmwares called
xc2028 1-0061: Reading firmware xc3028-v27.fw
cx18 0000:01:07.0: firmware: requesting xc3028-v27.fw
xc2028 1-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7
xc2028 1-0061: Reading firmware type BASE F8MHZ (3), id 0, size=8718.
xc2028 1-0061: Reading firmware type BASE F8MHZ MTS (7), id 0, size=8712.
xc2028 1-0061: Reading firmware type BASE FM (401), id 0, size=8562.
xc2028 1-0061: Reading firmware type BASE FM INPUT1 (c01), id 0, size=8576.
xc2028 1-0061: Reading firmware type BASE (1), id 0, size=8706.
xc2028 1-0061: Reading firmware type BASE MTS (5), id 0, size=8682.
xc2028 1-0061: Reading firmware type (0), id 100000007, size=161.
xc2028 1-0061: Reading firmware type MTS (4), id 100000007, size=169.
xc2028 1-0061: Reading firmware type (0), id 200000007, size=161.
xc2028 1-0061: Reading firmware type MTS (4), id 200000007, size=169.
xc2028 1-0061: Reading firmware type (0), id 400000007, size=161.
xc2028 1-0061: Reading firmware type MTS (4), id 400000007, size=169.
xc2028 1-0061: Reading firmware type (0), id 800000007, size=161.
xc2028 1-0061: Reading firmware type MTS (4), id 800000007, size=169.
xc2028 1-0061: Reading firmware type (0), id 3000000e0, size=161.
xc2028 1-0061: Reading firmware type MTS (4), id 3000000e0, size=169.
xc2028 1-0061: Reading firmware type (0), id c000000e0, size=161.
xc2028 1-0061: Reading firmware type MTS (4), id c000000e0, size=169.
xc2028 1-0061: Reading firmware type (0), id 200000, size=161.
xc2028 1-0061: Reading firmware type MTS (4), id 200000, size=169.
xc2028 1-0061: Reading firmware type (0), id 4000000, size=161.
xc2028 1-0061: Reading firmware type MTS (4), id 4000000, size=169.
xc2028 1-0061: Reading firmware type D2633 DTV6 ATSC (10030), id 0, size=149.
xc2028 1-0061: Reading firmware type D2620 DTV6 QAM (68), id 0, size=149.
xc2028 1-0061: Reading firmware type D2633 DTV6 QAM (70), id 0, size=149.
xc2028 1-0061: Reading firmware type D2620 DTV7 (88), id 0, size=149.
xc2028 1-0061: Reading firmware type D2633 DTV7 (90), id 0, size=149.
xc2028 1-0061: Reading firmware type D2620 DTV78 (108), id 0, size=149.
xc2028 1-0061: Reading firmware type D2633 DTV78 (110), id 0, size=149.
xc2028 1-0061: Reading firmware type D2620 DTV8 (208), id 0, size=149.
xc2028 1-0061: Reading firmware type D2633 DTV8 (210), id 0, size=149.
xc2028 1-0061: Reading firmware type FM (400), id 0, size=135.
xc2028 1-0061: Reading firmware type (0), id 10, size=161.
xc2028 1-0061: Reading firmware type MTS (4), id 10, size=169.
xc2028 1-0061: Reading firmware type (0), id 1000400000, size=169.
xc2028 1-0061: Reading firmware type (0), id c00400000, size=161.
xc2028 1-0061: Reading firmware type (0), id 800000, size=161.
xc2028 1-0061: Reading firmware type (0), id 8000, size=161.
xc2028 1-0061: Reading firmware type LCD (1000), id 8000, size=161.
xc2028 1-0061: Reading firmware type LCD NOGD (3000), id 8000, size=161.
xc2028 1-0061: Reading firmware type MTS (4), id 8000, size=169.
xc2028 1-0061: Reading firmware type (0), id b700, size=161.
xc2028 1-0061: Reading firmware type LCD (1000), id b700, size=161.
xc2028 1-0061: Reading firmware type LCD NOGD (3000), id b700, size=161.
xc2028 1-0061: Reading firmware type (0), id 2000, size=161.
xc2028 1-0061: Reading firmware type MTS (4), id b700, size=169.
xc2028 1-0061: Reading firmware type MTS LCD (1004), id b700, size=169.
xc2028 1-0061: Reading firmware type MTS LCD NOGD (3004), id b700, size=169.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_3280 (60000000), id 0, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_3300 (60000000), id 0, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_3440 (60000000), id 0, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_3460 (60000000), id 0, size=192.
xc2028 1-0061: Reading firmware type DTV6 ATSC OREN36 SCODE HAS_IF_3800 (60210020), id 0, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_4000 (60000000), id 0, size=192.
xc2028 1-0061: Reading firmware type DTV6 ATSC TOYOTA388 SCODE HAS_IF_4080 (60410020), id 0, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_4200 (60000000), id 0, size=192.
xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_4320 (60008000), id 8000, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_4450 (60000000), id 0, size=192.
xc2028 1-0061: Reading firmware type MTS LCD NOGD MONO IF SCODE HAS_IF_4500 (6002b004), id b700, size=192.
xc2028 1-0061: Reading firmware type LCD NOGD IF SCODE HAS_IF_4600 (60023000), id 8000, size=192.
xc2028 1-0061: Reading firmware type DTV6 QAM DTV7 DTV78 DTV8 ZARLINK456 SCODE HAS_IF_4760 (620003e0), id 0, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_4940 (60000000), id 0, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_5260 (60000000), id 0, size=192.
xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_5320 (60008000), id f00000007, size=192.
xc2028 1-0061: Reading firmware type DTV7 DTV78 DTV8 DIBCOM52 CHINA SCODE HAS_IF_5400 (65000380), id 0, size=192.
xc2028 1-0061: Reading firmware type DTV6 ATSC OREN538 SCODE HAS_IF_5580 (60110020), id 0, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_5640 (60000000), id 300000007, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_5740 (60000000), id c00000007, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_5900 (60000000), id 0, size=192.
xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_6000 (60008000), id c04c000f0, size=192.
xc2028 1-0061: Reading firmware type DTV6 QAM ATSC LG60 F6MHZ SCODE HAS_IF_6200 (68050060), id 0, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_6240 (60000000), id 10, size=192.
xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_6320 (60008000), id 200000, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_6340 (60000000), id 200000, size=192.
xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_6500 (60008000), id c044000e0, size=192.
xc2028 1-0061: Reading firmware type DTV6 ATSC ATI638 SCODE HAS_IF_6580 (60090020), id 0, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_6600 (60000000), id 3000000e0, size=192.
xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_6680 (60008000), id 3000000e0, size=192.
xc2028 1-0061: Reading firmware type DTV6 ATSC TOYOTA794 SCODE HAS_IF_8140 (60810020), id 0, size=192.
xc2028 1-0061: Reading firmware type SCODE HAS_IF_8200 (60000000), id 0, size=192.
xc2028 1-0061: Firmware files loaded.
xc2028 1-0061: checking firmware, user requested type=(0), id 0000000000001000, scode_tbl (0), scode_nr 0
xc2028 1-0061: load_firmware called
xc2028 1-0061: seek_firmware called, want type=BASE (1), id 0000000000000000.
xc2028 1-0061: Found firmware for type=BASE (1), id 0000000000000000.
xc2028 1-0061: Loading firmware for type=BASE (1), id 0000000000000000.
xc2028 1-0061: Load init1 firmware, if exists
xc2028 1-0061: load_firmware called
xc2028 1-0061: seek_firmware called, want type=BASE INIT1 (4001), id 0000000000000000.
xc2028 1-0061: Can't find firmware for type=BASE INIT1 (4001), id 0000000000000000.
xc2028 1-0061: load_firmware called
xc2028 1-0061: seek_firmware called, want type=BASE INIT1 (4001), id 0000000000000000.
xc2028 1-0061: Can't find firmware for type=BASE INIT1 (4001), id 0000000000000000.
xc2028 1-0061: load_firmware called
xc2028 1-0061: seek_firmware called, want type=(0), id 0000000000001000.
xc2028 1-0061: Found firmware for type=(0), id 000000000000b700.
xc2028 1-0061: Loading firmware for type=(0), id 000000000000b700.
xc2028 1-0061: Trying to load scode 0
xc2028 1-0061: load_scode called
xc2028 1-0061: seek_firmware called, want type=SCODE (20000000), id 000000000000b700.
xc2028 1-0061: Selecting best matching firmware (1 bits) for type=SCODE (20000000), id 000000000000b700:
xc2028 1-0061: Found firmware for type=SCODE (20000000), id 0000000000008000.
xc2028 1-0061: Loading SCODE for type=MONO SCODE HAS_IF_4320 (60008000), id 0000000000008000.
xc2028 1-0061: xc2028_get_reg 0004 called
xc2028 1-0061: xc2028_get_reg 0008 called
xc2028 1-0061: Device is Xceive 3028 version 1.0, firmware version 2.7
xc2028 1-0061: divisor= 00 00 64 00 (freq=400.000)
tuner 1-0061: tv freq set to 67.25
xc2028 1-0061: xc2028_set_analog_freq called
xc2028 1-0061: generic_set_freq called
xc2028 1-0061: should set frequency 67250 kHz
xc2028 1-0061: check_firmware called
xc2028 1-0061: checking firmware, user requested type=(0), id 0000000000001000, scode_tbl (0), scode_nr 0
xc2028 1-0061: BASE firmware not changed.
xc2028 1-0061: Std-specific firmware already loaded.
xc2028 1-0061: SCODE firmware already loaded.
xc2028 1-0061: xc2028_get_reg 0004 called
xc2028 1-0061: xc2028_get_reg 0008 called
xc2028 1-0061: Device is Xceive 3028 version 1.0, firmware version 2.7
xc2028 1-0061: divisor= 00 00 10 d0 (freq=67.250)
cx18-0:  file: open encoder MPEG
cx18-0:  file: open encoder MPEG
tuner 1-0061: tv freq set to 67.25
xc2028 1-0061: xc2028_set_analog_freq called
xc2028 1-0061: generic_set_freq called
xc2028 1-0061: should set frequency 67250 kHz
xc2028 1-0061: check_firmware called
xc2028 1-0061: checking firmware, user requested type=F8MHZ (2), id 00000000000000ff, scode_tbl (0), scode_nr 0
xc2028 1-0061: load_firmware called
xc2028 1-0061: seek_firmware called, want type=BASE F8MHZ (3), id 0000000000000000.
xc2028 1-0061: Found firmware for type=BASE F8MHZ (3), id 0000000000000000.
xc2028 1-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000.
xc2028 1-0061: Load init1 firmware, if exists
xc2028 1-0061: load_firmware called
xc2028 1-0061: seek_firmware called, want type=BASE INIT1 F8MHZ (4003), id 0000000000000000.
xc2028 1-0061: Can't find firmware for type=BASE INIT1 F8MHZ (4003), id 0000000000000000.
xc2028 1-0061: load_firmware called
xc2028 1-0061: seek_firmware called, want type=BASE INIT1 (4001), id 0000000000000000.
xc2028 1-0061: Can't find firmware for type=BASE INIT1 (4001), id 0000000000000000.
xc2028 1-0061: load_firmware called
xc2028 1-0061: seek_firmware called, want type=F8MHZ (2), id 00000000000000ff.
xc2028 1-0061: Selecting best matching firmware (3 bits) for type=(0), id 00000000000000ff:
xc2028 1-0061: Found firmware for type=(0), id 0000000100000007.
xc2028 1-0061: Loading firmware for type=(0), id 0000000100000007.
xc2028 1-0061: Trying to load scode 0
xc2028 1-0061: load_scode called
xc2028 1-0061: seek_firmware called, want type=F8MHZ SCODE (20000002), id 0000000100000007.
xc2028 1-0061: Found firmware for type=SCODE (20000000), id 0000000f00000007.
xc2028 1-0061: Loading SCODE for type=MONO SCODE HAS_IF_5320 (60008000), id 0000000f00000007.
xc2028 1-0061: xc2028_get_reg 0004 called
xc2028 1-0061: xc2028_get_reg 0008 called
xc2028 1-0061: Device is Xceive 3028 version 1.0, firmware version 2.7
xc2028 1-0061: divisor= 00 00 10 d0 (freq=67.250)
cx18-0:  file: open encoder MPEG
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: tv freq set to 111.25
xc2028 1-0061: xc2028_set_analog_freq called
xc2028 1-0061: generic_set_freq called
xc2028 1-0061: should set frequency 111250 kHz
xc2028 1-0061: check_firmware called
xc2028 1-0061: checking firmware, user requested type=F8MHZ (2), id 00000000000000ff, scode_tbl (0), scode_nr 0
xc2028 1-0061: BASE firmware not changed.
xc2028 1-0061: Std-specific firmware already loaded.
xc2028 1-0061: SCODE firmware already loaded.
xc2028 1-0061: xc2028_get_reg 0004 called
xc2028 1-0061: xc2028_get_reg 0008 called
xc2028 1-0061: Device is Xceive 3028 version 1.0, firmware version 2.7
xc2028 1-0061: divisor= 00 00 1b d0 (freq=111.250)
cx18-0:  file: open encoder MPEG
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
cx18-0:  file: open encoder MPEG
cx18-0: =================  START STATUS CARD #0  =================
cx18-0: Version: 1.2.0  Card: Leadtek WinFast PVR2100
cx18-0 843: Video signal:              present
cx18-0 843: Detected format:           PAL-BDGHI
cx18-0 843: Specified standard:        PAL-BDGHI
cx18-0 843: Specified video input:     Composite 2
cx18-0 843: Specified audioclock freq: 48000 Hz
cx18-0 843: Detected audio mode:       mono
cx18-0 843: Detected audio standard:   no detected audio standard
cx18-0 843: Audio muted:               yes
cx18-0 843: Audio microcontroller:     running
cx18-0 843: Configured audio standard: automatic detection
cx18-0 843: Configured audio system:   automatic standard and mode detection
cx18-0 843: Specified audio input:     Tuner (In5)
cx18-0 843: Preferred audio mode:      stereo
cx18-0 843: Selected 65 MHz format:    system DK
cx18-0 843: Selected 45 MHz format:    A2-M
cx18-0 gpio-reset-ctrl: GPIO:  direction 0x00000007, value 0x00000006
tuner 1-0061: Tuner mode:      analog TV
tuner 1-0061: Frequency:       111.25 MHz
tuner 1-0061: Standard:        0x000000ff
cx18-0 gpio-mux: GPIO:  direction 0x00000007, value 0x00000006
cx18-0: Video Input: Tuner 1
cx18-0: Audio Input: Tuner 1
cx18-0: GPIO:  direction 0x00000007, value 0x00000006
cx18-0: Tuner: TV
cx18-0: Stream: MPEG-2 Program Stream
cx18-0: VBI Format: No VBI
cx18-0: Video:  720x576, 25 fps
cx18-0: Video:  MPEG-2, 4x3, Variable Bitrate, 6000000, Peak 8000000
cx18-0: Video:  GOP Size 15, 2 B-Frames, GOP Closure
cx18-0: Audio:  48 kHz, MPEG-1/2 Layer II, 224 kbps, Stereo, No Emphasis, No CRC
cx18-0: Spatial Filter:  Manual, Luma 1D Horizontal, Chroma 1D Horizontal, 0
cx18-0: Temporal Filter: Manual, 8
cx18-0: Median Filter:   Off, Luma [0, 255], Chroma [0, 255]
cx18-0: Status flags: 0x00200001
cx18-0: Stream encoder MPEG: status 0x0000, 0% of 2048 KiB (64 buffers) in use
cx18-0: Stream encoder YUV: status 0x0000, 0% of 2048 KiB (16 buffers) in use
cx18-0: Stream encoder VBI: status 0x0000, 0% of 1015 KiB (20 buffers) in use
cx18-0: Stream encoder PCM audio: status 0x0000, 0% of 1024 KiB (256 buffers) in use
cx18-0: Read MPEG/VBI: 15400960/0 bytes
cx18-0: ==================  END STATUS CARD #0  ==================
cx18-0:  file: open encoder MPEG
tuner 1-0061: tv freq set to 111.25
xc2028 1-0061: xc2028_set_analog_freq called
xc2028 1-0061: generic_set_freq called
xc2028 1-0061: should set frequency 111250 kHz
xc2028 1-0061: check_firmware called
xc2028 1-0061: checking firmware, user requested type=F8MHZ (2), id 00000000000000e0, scode_tbl (0), scode_nr 0
xc2028 1-0061: BASE firmware not changed.
xc2028 1-0061: load_firmware called
xc2028 1-0061: seek_firmware called, want type=F8MHZ (2), id 00000000000000e0.
xc2028 1-0061: Found firmware for type=(0), id 00000003000000e0.
xc2028 1-0061: Loading firmware for type=(0), id 00000003000000e0.
xc2028 1-0061: Trying to load scode 0
xc2028 1-0061: load_scode called
xc2028 1-0061: seek_firmware called, want type=F8MHZ SCODE (20000002), id 00000003000000e0.
xc2028 1-0061: Found firmware for type=SCODE (20000000), id 00000003000000e0.
xc2028 1-0061: Loading SCODE for type=SCODE HAS_IF_6600 (60000000), id 00000003000000e0.
xc2028 1-0061: xc2028_get_reg 0004 called
xc2028 1-0061: xc2028_get_reg 0008 called
xc2028 1-0061: Device is Xceive 3028 version 1.0, firmware version 2.7
xc2028 1-0061: divisor= 00 00 1b d0 (freq=111.250)
cx18-0:  file: open encoder MPEG
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
tuner 1-0061: Cmd g_tuner accepted for analog TV
cx18-0:  file: open encoder MPEG
cx18-0: =================  START STATUS CARD #0  =================
cx18-0: Version: 1.2.0  Card: Leadtek WinFast PVR2100
cx18-0 843: Video signal:              present
cx18-0 843: Detected format:           PAL-BDGHI
cx18-0 843: Specified standard:        PAL-BDGHI
cx18-0 843: Specified video input:     Composite 2
cx18-0 843: Specified audioclock freq: 48000 Hz
cx18-0 843: Detected audio mode:       mono
cx18-0 843: Detected audio standard:   A2-DK1
cx18-0 843: Audio muted:               no
cx18-0 843: Audio microcontroller:     running
cx18-0 843: Configured audio standard: automatic detection
cx18-0 843: Configured audio system:   automatic standard and mode detection
cx18-0 843: Specified audio input:     Tuner (In5)
cx18-0 843: Preferred audio mode:      stereo
cx18-0 843: Selected 65 MHz format:    system DK
cx18-0 843: Selected 45 MHz format:    A2-M
cx18-0 gpio-reset-ctrl: GPIO:  direction 0x00000007, value 0x00000006
tuner 1-0061: Tuner mode:      analog TV
tuner 1-0061: Frequency:       111.25 MHz
tuner 1-0061: Standard:        0x000000e0
cx18-0 gpio-mux: GPIO:  direction 0x00000007, value 0x00000006
cx18-0: Video Input: Tuner 1
cx18-0: Audio Input: Tuner 1
cx18-0: GPIO:  direction 0x00000007, value 0x00000006
cx18-0: Tuner: TV
cx18-0: Stream: MPEG-2 Program Stream
cx18-0: VBI Format: No VBI
cx18-0: Video:  720x576, 25 fps
cx18-0: Video:  MPEG-2, 4x3, Variable Bitrate, 6000000, Peak 8000000
cx18-0: Video:  GOP Size 15, 2 B-Frames, GOP Closure
cx18-0: Audio:  48 kHz, MPEG-1/2 Layer II, 224 kbps, Stereo, No Emphasis, No CRC
cx18-0: Spatial Filter:  Manual, Luma 1D Horizontal, Chroma 1D Horizontal, 0
cx18-0: Temporal Filter: Manual, 8
cx18-0: Median Filter:   Off, Luma [0, 255], Chroma [0, 255]
cx18-0: Status flags: 0x00200001
cx18-0: Stream encoder MPEG: status 0x0000, 0% of 2048 KiB (64 buffers) in use
cx18-0: Stream encoder YUV: status 0x0000, 0% of 2048 KiB (16 buffers) in use
cx18-0: Stream encoder VBI: status 0x0000, 0% of 1015 KiB (20 buffers) in use
cx18-0: Stream encoder PCM audio: status 0x0000, 0% of 1024 KiB (256 buffers) in use
cx18-0: Read MPEG/VBI: 2424832/0 bytes
cx18-0: ==================  END STATUS CARD #0  ==================

[-- Attachment #3: Type: text/plain, Size: 14 bytes --]


Thanks.

-- 

Re: cx18: Need information on SECAM-D/K problem with PVR-2100

[Aleksandr V. Piskunov]

On Mon, Jan 04, 2010 at 02:40:47PM +0300, Sergey Bolshakov wrote:
> >>>>> "Andy" == Andy Walls <awalls@radix.net> writes:
> 
>  > Sergey,
>  > On IRC you mentioned a problem of improper detection of SECAM-D/K with
>  > the Leadtek PVR2100 (XC2028 and CX23418) from an RF source.
> 
> It was some misunderstanding, i suppose, i do not have problems with
> secam, i had improper detection of sound standard (and silence as
> result) on pal channels. Later i've found, that fully-specified std
> (pal-d instead of just pal) helps, so i can live with that.
> 

Thats a general problem of any card with XC2028 silicon tuner, user
(tv app) has to specify a precise substandard (audio carrier frequency)
for sound to work.

PAL-BG users (western europe, etc) won't notice it, since in case of 
generic PAL standard set, xceive tuner defaults to BG substandard firmware.

In other cases, you either have to specify correct standard (DK, etc) or
try to specify PAL-I, which seems to work for BG, DK and I carriers.
At least it works for me :)

See http://osdir.com/ml/linux-media/2009-09/msg00997.html for more details.