From: Richard Atterer <atterer@debian.org>
To: linux-media@vger.kernel.org
Subject: bttv: No analogue sound output by TV card
Date: Fri, 1 Oct 2010 00:19:53 +0200 [thread overview]
Message-ID: <20100930221953.GA7062@arbonne.lan> (raw)
[Please CC me, I'm not on the list.]
Hi,
after switching from 2.6.34 to 2.6.36-rc5, the sound on my old Hauppauge
analogue TV card has stopped working. Audio out from the TV card is
connected to line-in of my motherboard (Gigabyte EG45M-DS2H) using the
short cable that came with the TV card. Other audio sources (e.g. MP3
player) are audible when connected to line-in. The TV picture is fine.
The log messages look really similar for the two kernels.
2.6.34 works:
kernel: bttv: driver version 0.9.18 loaded
kernel: bttv: using 8 buffers with 2080k (520 pages) each for capture
kernel: bttv: Bt8xx card found (0).
kernel: bttv0: Bt878 (rev 17) at 0000:03:01.0, irq: 19, latency: 32, mmio: 0xe3600000
kernel: bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
kernel: bttv0: using: Hauppauge (bt878) [card=10,autodetected]
kernel: IRQ 19/bttv0: IRQF_DISABLED is not guaranteed on shared IRQs
kernel: bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
kernel: bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
kernel: tveeprom 1-0050: Hauppauge model 44354, rev D147, serial# 1234567
kernel: tveeprom 1-0050: tuner model is LG TP18PSB01D (idx 47, type 28)
kernel: tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04)
kernel: tveeprom 1-0050: audio processor is MSP3415 (idx 6)
kernel: tveeprom 1-0050: has radio
kernel: bttv0: Hauppauge eeprom indicates model#44354
kernel: bttv0: tuner type=28
kernel: msp3400 1-0040: MSP3415D-B3 found @ 0x80 (bt878 #0 [sw])
kernel: msp3400 1-0040: msp3400 supports nicam, mode is autodetect
kernel: tuner 1-0061: chip found @ 0xc2 (bt878 #0 [sw])
kernel: tuner-simple 1-0061: creating new instance
kernel: tuner-simple 1-0061: type set to 28 (LG PAL_BG+FM (TPI8PSB01D))
kernel: bttv0: registered device video0
kernel: bttv0: registered device vbi0
kernel: bttv0: registered device radio0
kernel: bttv0: PLL: 28636363 => 35468950 .
kernel: bttv0: PLL: 28636363 => 35468950 . ok
kernel: ok
2.6.36-rc5 does not work:
kernel: bttv: driver version 0.9.18 loaded
kernel: bttv: using 8 buffers with 2080k (520 pages) each for capture
kernel: bttv: Bt8xx card found (0).
kernel: bttv0: Bt878 (rev 17) at 0000:03:01.0, irq: 19, latency: 32, mmio: 0xe3600000
kernel: bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
kernel: bttv0: using: Hauppauge (bt878) [card=10,autodetected]
kernel: bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
kernel: bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
kernel: tveeprom 1-0050: Hauppauge model 44354, rev D147, serial# 1234567
kernel: tveeprom 1-0050: tuner model is LG TP18PSB01D (idx 47, type 28)
kernel: tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04)
kernel: tveeprom 1-0050: audio processor is MSP3415 (idx 6)
kernel: tveeprom 1-0050: has radio
kernel: bttv0: Hauppauge eeprom indicates model#44354
kernel: bttv0: tuner type=28
kernel: msp3400 1-0040: MSP3415D-B3 found @ 0x80 (bt878 #0 [sw])
kernel: msp3400 1-0040: msp3400 supports nicam, mode is autodetect
kernel: tuner 1-0061: chip found @ 0xc2 (bt878 #0 [sw])
kernel: tuner-simple 1-0061: creating new instance
kernel: tuner-simple 1-0061: type set to 28 (LG PAL_BG+FM (TPI8PSB01D))
kernel: bttv0: registered device video0
kernel: bttv0: registered device vbi0
kernel: bttv0: registered device radio0
kernel: bttv0: PLL: 28636363 => 35468950 . ok
The only real change is that the IRQF_DISABLED warning is gone.
Cheers,
Richard
--
__ ,
| ) /| Richard Atterer
| \/ | http://atterer.org
next reply other threads:[~2010-09-30 22:19 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-09-30 22:19 Richard Atterer [this message]
2010-10-07 20:55 ` bttv: No analogue sound output by TV card Richard Atterer
2010-10-07 21:01 ` Mauro Carvalho Chehab
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100930221953.GA7062@arbonne.lan \
--to=atterer@debian.org \
--cc=linux-media@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox