Re: [PATCH] tvp5150: Fix breakage for serial usage

[Mauro Carvalho Chehab <mchehab@osg.samsung.com>]

Em Mon, 25 Jan 2016 19:23:40 +0200
Laurent Pinchart <laurent.pinchart@ideasonboard.com> escreveu:

> Hi Mauro,
> 
> On Monday 25 January 2016 14:44:56 Mauro Carvalho Chehab wrote:
> > changeset 460b6c0831cb ("tvp5150: Add s_stream subdev operation
> > support") broke for em28xx-based devices with uses tvp5150. On those
> > devices, touching the TVP5150_MISC_CTL register causes em28xx to stop
> > streaming.
> > 
> > I suspect that it uses the 27 MHz clock provided by tvp5150 to feed
> > em28xx. So, change the logic to do nothing on s_stream if the tvp5150 is
> > not set up to work with V4L2_MBUS_PARALLEL.
> > 
> > Cc: Javier Martinez Canillas <javier@osg.samsung.com>
> > Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
> > ---
> >  drivers/media/i2c/tvp5150.c | 9 ++++-----
> >  1 file changed, 4 insertions(+), 5 deletions(-)
> > 
> > diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c
> > index 437f1a7ecb96..779c6f453cc9 100644
> > --- a/drivers/media/i2c/tvp5150.c
> > +++ b/drivers/media/i2c/tvp5150.c
> > @@ -975,19 +975,18 @@ static int tvp5150_g_mbus_config(struct v4l2_subdev
> > *sd, static int tvp5150_s_stream(struct v4l2_subdev *sd, int enable)
> >  {
> >  	struct tvp5150 *decoder = to_tvp5150(sd);
> > -	/* Output format: 8-bit ITU-R BT.656 with embedded syncs */
> > -	int val = 0x09;
> > 
> >  	/* Output format: 8-bit 4:2:2 YUV with discrete sync */
> > -	if (decoder->mbus_type == V4L2_MBUS_PARALLEL)
> > -		val = 0x0d;
> > +	if (decoder->mbus_type != V4L2_MBUS_PARALLEL)
> > +		return 0;  
> 
> This will break TVP5151 operation with the OMAP3 ISP in BT.656 mode. The OMAP3 
> requires the TVP5151 to start and stop streaming when requested.

Does OMAP3 work in BT.656 with the current hardware? If so, then we'll need
an extra property to enable the start/stop ops if used with OMAP3.

Otherwise, we could add a notice here and write such change when needed.

> 
> > 
> >  	/* Initializes TVP5150 to its default values */
> >  	/* # set PCLK (27MHz) */
> >  	tvp5150_write(sd, TVP5150_CONF_SHARED_PIN, 0x00);
> > 
> > +	/* Output format: 8-bit ITU-R BT.656 with embedded syncs */
> >  	if (enable)
> > -		tvp5150_write(sd, TVP5150_MISC_CTL, val);
> > +		tvp5150_write(sd, TVP5150_MISC_CTL, 0x09);
> >  	else
> >  		tvp5150_write(sd, TVP5150_MISC_CTL, 0x00);  
>