[PATCH RFC] omap3isp: prevent releasing MC too early

[PATCH RFC] omap3isp: prevent releasing MC too early

[Mauro Carvalho Chehab]

Avoid calling streamoff without having the media structs allocated.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
---

Javier,

Could you please test this patch?

Thanks!
Mauro

 drivers/media/platform/omap3isp/ispvideo.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/media/platform/omap3isp/ispvideo.c b/drivers/media/platform/omap3isp/ispvideo.c
index 7354469670b7..f60995ed0a1f 100644
--- a/drivers/media/platform/omap3isp/ispvideo.c
+++ b/drivers/media/platform/omap3isp/ispvideo.c
@@ -1488,11 +1488,17 @@ int omap3isp_video_register(struct isp_video *video, struct v4l2_device *vdev)
 			"%s: could not register video device (%d)\n",
 			__func__, ret);
 
+	/* Prevent destroying MC before unregistering */
+	kobject_get(vdev->v4l2_dev->mdev->devnode->dev.parent);
+
 	return ret;
 }
 
 void omap3isp_video_unregister(struct isp_video *video)
 {
-	if (video_is_registered(&video->video))
-		video_unregister_device(&video->video);
+	if (!video_is_registered(&video->video))
+		return;
+
+	video_unregister_device(&video->video);
+	kobject_put(vdev->v4l2_dev->mdev->devnode->dev.parent);
 }
-- 
2.9.3

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Laurent Pinchart]

Hi Mauro,

(CC'ing Greg)

On Wednesday 14 Dec 2016 13:14:06 Mauro Carvalho Chehab wrote:
> Avoid calling streamoff without having the media structs allocated.
> 
> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The driver has a maintainer listed in MAINTAINERS, and you know that Sakari is 
also actively involved here. You could have CC'ed us.

> ---
> 
> Javier,
> 
> Could you please test this patch?
> 
> Thanks!
> Mauro
> 
>  drivers/media/platform/omap3isp/ispvideo.c | 10 ++++++++--
>  1 file changed, 8 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/media/platform/omap3isp/ispvideo.c
> b/drivers/media/platform/omap3isp/ispvideo.c index
> 7354469670b7..f60995ed0a1f 100644
> --- a/drivers/media/platform/omap3isp/ispvideo.c
> +++ b/drivers/media/platform/omap3isp/ispvideo.c
> @@ -1488,11 +1488,17 @@ int omap3isp_video_register(struct isp_video *video,
> struct v4l2_device *vdev) "%s: could not register video device (%d)\n",
>  			__func__, ret);
> 
> +	/* Prevent destroying MC before unregistering */
> +	kobject_get(vdev->v4l2_dev->mdev->devnode->dev.parent);

This doesn't even compile. Please make sure to at least compile-test patches 
you send for review, otherwise you end up wasting time for all reviewers and 
testers. I assume you meant

	kobject_get(&vdev->mdev->devnode->dev.parent->kobj);

and similarly below.

That's a long list of pointer dereferences, going deep down the device core. 
Greg, are drivers allowed to do this by the driver model ?

> +
>  	return ret;
>  }
> 
>  void omap3isp_video_unregister(struct isp_video *video)
>  {
> -	if (video_is_registered(&video->video))
> -		video_unregister_device(&video->video);
> +	if (!video_is_registered(&video->video))
> +		return;
> +
> +	video_unregister_device(&video->video);
> +	kobject_put(vdev->v4l2_dev->mdev->devnode->dev.parent);
>  }

-- 
Regards,

Laurent Pinchart

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Greg KH]

On Thu, Dec 15, 2016 at 02:13:42PM +0200, Laurent Pinchart wrote:
> Hi Mauro,
> 
> (CC'ing Greg)
> 
> On Wednesday 14 Dec 2016 13:14:06 Mauro Carvalho Chehab wrote:
> > Avoid calling streamoff without having the media structs allocated.
> > 
> > Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
> 
> The driver has a maintainer listed in MAINTAINERS, and you know that Sakari is 
> also actively involved here. You could have CC'ed us.
> 
> > ---
> > 
> > Javier,
> > 
> > Could you please test this patch?
> > 
> > Thanks!
> > Mauro
> > 
> >  drivers/media/platform/omap3isp/ispvideo.c | 10 ++++++++--
> >  1 file changed, 8 insertions(+), 2 deletions(-)
> > 
> > diff --git a/drivers/media/platform/omap3isp/ispvideo.c
> > b/drivers/media/platform/omap3isp/ispvideo.c index
> > 7354469670b7..f60995ed0a1f 100644
> > --- a/drivers/media/platform/omap3isp/ispvideo.c
> > +++ b/drivers/media/platform/omap3isp/ispvideo.c
> > @@ -1488,11 +1488,17 @@ int omap3isp_video_register(struct isp_video *video,
> > struct v4l2_device *vdev) "%s: could not register video device (%d)\n",
> >  			__func__, ret);
> > 
> > +	/* Prevent destroying MC before unregistering */
> > +	kobject_get(vdev->v4l2_dev->mdev->devnode->dev.parent);
> 
> This doesn't even compile. Please make sure to at least compile-test patches 
> you send for review, otherwise you end up wasting time for all reviewers and 
> testers. I assume you meant
> 
> 	kobject_get(&vdev->mdev->devnode->dev.parent->kobj);
> 
> and similarly below.
> 
> That's a long list of pointer dereferences, going deep down the device core. 
> Greg, are drivers allowed to do this by the driver model ?

WTF?

Eeek, no no no no!

First off, no driver should EVER have to call a "raw" kobject call,
that's a huge sign that you are doing something really really wrong.

Secondly, you NEVER grab a reference to a structure like this, you use
the "correct" driver/bus api calls.

Thirdly, ugh, how to say this nicely...  The whole idea that something
like this could actually be a real solution to a problem is insane.

Look at what you are really doing here, trying to grab an extra
reference on something that in reality, should never go away anyhow.
Your parent structure should already always have the reference count
incremented and will not disappear underneath you at all.  And if this
isn't your "parent", you have no right at all to go grab random
references across the device tree for no reason other than you feel you
don't want it to go away.  If you don't want something to go away, you
properly get the reference (hint, you already should have if you have
this type of pointer chain to the object.)

If this type of solution is somehow the "correct" one, the v4l driver
model interaction is severely broken and needs to be fixed.

What bug is this that caused this type of hack to even be proposed?  Is
it a bug or a regression?  If a regression, can someone show me the
commit that would cause such a monstrosity to be proposed?

Laurent, sorry, I know I said I was going to debug a USB V4L reference
counting problem last week, I had to travel and haven't had the chance
to do so.  I'll try to get to it today.  Hopefully that issue has
nothing to do with this problem.  Because if so, ugh...

Mauro, again, please never propose something like this again.

greg k-h

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Mauro Carvalho Chehab]

Em Thu, 15 Dec 2016 14:13:42 +0200
Laurent Pinchart <laurent.pinchart@ideasonboard.com> escreveu:

> Hi Mauro,
> 
> (CC'ing Greg)
> 
> On Wednesday 14 Dec 2016 13:14:06 Mauro Carvalho Chehab wrote:
> > Avoid calling streamoff without having the media structs allocated.
> > 
> > Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>  
> 
> The driver has a maintainer listed in MAINTAINERS, and you know that Sakari is 
> also actively involved here. You could have CC'ed us.

Yes, sure.

> 
> > ---
> > 
> > Javier,
> > 
> > Could you please test this patch?
> > 
> > Thanks!
> > Mauro
> > 
> >  drivers/media/platform/omap3isp/ispvideo.c | 10 ++++++++--
> >  1 file changed, 8 insertions(+), 2 deletions(-)
> > 
> > diff --git a/drivers/media/platform/omap3isp/ispvideo.c
> > b/drivers/media/platform/omap3isp/ispvideo.c index
> > 7354469670b7..f60995ed0a1f 100644
> > --- a/drivers/media/platform/omap3isp/ispvideo.c
> > +++ b/drivers/media/platform/omap3isp/ispvideo.c
> > @@ -1488,11 +1488,17 @@ int omap3isp_video_register(struct isp_video *video,
> > struct v4l2_device *vdev) "%s: could not register video device (%d)\n",
> >  			__func__, ret);
> > 
> > +	/* Prevent destroying MC before unregistering */
> > +	kobject_get(vdev->v4l2_dev->mdev->devnode->dev.parent);  
> 
> This doesn't even compile. Please make sure to at least compile-test patches 
> you send for review, otherwise you end up wasting time for all reviewers and 
> testers. I assume you meant
> 
> 	kobject_get(&vdev->mdev->devnode->dev.parent->kobj);
> 
> and similarly below.

Yes.

Btw, Javier tested it yesterday with the above fix, but it didn't solve the
issue, because the problem is elsewhere.

What happens is that omap3isp driver calls media_device_unregister()
too early. Right now, it is called at omap3isp_video_device_release(),
with happens when a driver unbind is ordered by userspace, and not after
the last usage of all /dev/video?? devices.

There are two possible fixes:

1) at omap3isp_video_device_release(), streamoff all streams and mark
that the media device will be gone.

2) instead of using video_device_release_empty for the video->video.release,
create a omap3isp_video_device_release() that will call
media_device_unregister() when destroying the last /dev/video?? devnode.

I have a half-baked patch for (2). I'll try to finish it and do some
tests.

Unfortunately, I don't have any OMAP3 device that has a camera
module, except for a N9 device with a damaged display.

Sakari,

Is there a way for me to use the N9 device to test it without a
display? AFAIKT, the device is operational, and I *guess* it is
on developer's mode, but not really sure.

Thanks,
Mauro

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Javier Martinez Canillas]

Hello Mauro,

On 12/15/2016 09:37 AM, Mauro Carvalho Chehab wrote:

[snip]

> 
> What happens is that omap3isp driver calls media_device_unregister()
> too early. Right now, it is called at omap3isp_video_device_release(),
> with happens when a driver unbind is ordered by userspace, and not after
> the last usage of all /dev/video?? devices.
> 
> There are two possible fixes:
> 
> 1) at omap3isp_video_device_release(), streamoff all streams and mark
> that the media device will be gone.
> 
> 2) instead of using video_device_release_empty for the video->video.release,
> create a omap3isp_video_device_release() that will call
> media_device_unregister() when destroying the last /dev/video?? devnode.
>

There's also option (3), to have a proper refcounting to make sure that
the media device node is not freed until all references to it are gone.

I understand that's what Sakari's RFC patches do. I'll try to make some
time tomorrow to test and review his patches.
 
Best regards,
-- 
Javier Martinez Canillas
Open Source Group
Samsung Research America

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Mauro Carvalho Chehab]

Em Thu, 15 Dec 2016 09:42:35 -0300
Javier Martinez Canillas <javier@osg.samsung.com> escreveu:

> Hello Mauro,
> 
> On 12/15/2016 09:37 AM, Mauro Carvalho Chehab wrote:
> 
> [snip]
> 
> > 
> > What happens is that omap3isp driver calls media_device_unregister()
> > too early. Right now, it is called at omap3isp_video_device_release(),
> > with happens when a driver unbind is ordered by userspace, and not after
> > the last usage of all /dev/video?? devices.
> > 
> > There are two possible fixes:
> > 
> > 1) at omap3isp_video_device_release(), streamoff all streams and mark
> > that the media device will be gone.

I actually meant to say: isp_unregister_entities() here.

> > 
> > 2) instead of using video_device_release_empty for the video->video.release,
> > create a omap3isp_video_device_release() that will call
> > media_device_unregister() when destroying the last /dev/video?? devnode.
> >  
> 
> There's also option (3), to have a proper refcounting to make sure that
> the media device node is not freed until all references to it are gone.

Yes, that's another alternative.

> I understand that's what Sakari's RFC patches do. I'll try to make some
> time tomorrow to test and review his patches.

The biggest problem with Sakari's patches is that it starts by 
reverting 3 patches, and this will cause regressions on existing
devices.

Development should be incremental.

I didn't review carefully his series (as it started the wrong way),
but I guess there's another problem on it: as OMAP3 remove entities
at isp_unregister_entities(), while adding a kref to media_device
will prevent an oops, the streamoff logic won't work anymore, as
the entities that were supposed to be at the graph will have been
removed by then.

Ok, we can roll the snow ball and add kref's to entities and links,
but IMHO, we're trying to kill a fly with a death star: instead,
the better is to just fix the driver in a way that it would be
streaming off everything at isp_unregister_entities(), before
dropping the entities and the media controller.

Regards,
Mauro

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Laurent Pinchart]

Hi Mauro,

On Thursday 15 Dec 2016 10:37:34 Mauro Carvalho Chehab wrote:
> Em Thu, 15 Dec 2016 14:13:42 +0200 Laurent Pinchart escreveu:
> > On Wednesday 14 Dec 2016 13:14:06 Mauro Carvalho Chehab wrote:
> >> Avoid calling streamoff without having the media structs allocated.
> >> 
> >> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
> > 
> > The driver has a maintainer listed in MAINTAINERS, and you know that
> > Sakari is also actively involved here. You could have CC'ed us.
> 
> Yes, sure.
> 
> >> ---
> >> 
> >> Javier,
> >> 
> >> Could you please test this patch?
> >> 
> >> Thanks!
> >> Mauro
> >> 
> >>  drivers/media/platform/omap3isp/ispvideo.c | 10 ++++++++--
> >>  1 file changed, 8 insertions(+), 2 deletions(-)
> >> 
> >> diff --git a/drivers/media/platform/omap3isp/ispvideo.c
> >> b/drivers/media/platform/omap3isp/ispvideo.c index
> >> 7354469670b7..f60995ed0a1f 100644
> >> --- a/drivers/media/platform/omap3isp/ispvideo.c
> >> +++ b/drivers/media/platform/omap3isp/ispvideo.c
> >> @@ -1488,11 +1488,17 @@ int omap3isp_video_register(struct isp_video
> >> *video, struct v4l2_device *vdev) "%s: could not register video device
> >> (%d)\n",> > 
> >>  			__func__, ret);
> >> 
> >> +	/* Prevent destroying MC before unregistering */
> >> +	kobject_get(vdev->v4l2_dev->mdev->devnode->dev.parent);
> > 
> > This doesn't even compile. Please make sure to at least compile-test
> > patches you send for review, otherwise you end up wasting time for all
> > reviewers and testers. I assume you meant
> > 
> > 	kobject_get(&vdev->mdev->devnode->dev.parent->kobj);
> > 
> > and similarly below.
> 
> Yes.
> 
> Btw, Javier tested it yesterday with the above fix, but it didn't solve the
> issue, because the problem is elsewhere.
> 
> What happens is that omap3isp driver calls media_device_unregister()
> too early. Right now, it is called at omap3isp_video_device_release(),

No, it's called from isp_unregister_entities() <- isp_remove() <- platform 
driver .remove.

> with happens when a driver unbind is ordered by userspace, and not after
> the last usage of all /dev/video?? devices.

That's the right place to *unregister* the media device, but of course not the 
right place to *free* it. Unregistering the media device means marking it as 
closed for business, ensuring at least that any new userspace request will be 
rejected. It doesn't mean that memory should be freed at that point, the 
object must still remain accessible in the kernel for as long as it has users.

> There are two possible fixes:
> 
> 1) at omap3isp_video_device_release(),

There's no such function. I assume you mean isp_remove().

> streamoff all streams and mark that the media device will be gone.

The hardware should certainly be stopped at .remove() time, but trying to fake 
a userspace API call there through the driver's back is another case of 
bypassing API layers, it's more a hack than a clean fix.

> 2) instead of using video_device_release_empty for the video->video.release,
> create a omap3isp_video_device_release() that will call
> media_device_unregister() when destroying the last /dev/video?? devnode.

As explained above, the media device should be unregistered at .remove() time. 
It should be freed at .remove() time.

The media device can be accessed through multiple means. Aside from the 
userspace API exposed through a devnode, we also store the media device 
pointer in v4l2_device, as well as in videodev and v4l2_subdev through the 
embedded media_entity. videodev and v4l2_subdev expose a userspace API that 
require a .release() handler for the corresponding device nodes (note that I'm 
talking about the file operations release handler, not the release handler for 
the structures themselves), and that .release() handler is implemented in a 
way that does or can dereference the media_device object.

For instance, the v4l2_subdev release handler subdev_close() contains the 
following code

        if (sd->internal_ops && sd->internal_ops->close)
                sd->internal_ops->close(sd, subdev_fh);
#if defined(CONFIG_MEDIA_CONTROLLER)
        if (sd->v4l2_dev->mdev)
                media_entity_put(&sd->entity);
#endif

that both accesses media objects directly, and allow the driver to do through 
its subdev .close() operation handler. The videodev .release() handler 
v4l2_release() has the same issue with

        if (vdev->fops->release)
                ret = vdev->fops->release(filp);

and then calls video_put() that ends up invoking v4l2_device_release() which 
does touch the media_device and then the struct videodev .release() operation, 
again implemented by drivers (although that one should just be one or multiple 
kfree in most cases).

There are lots of way in which the media_device structure can be accessed, 
sometimes probably for bad reasons, but most of the time for legitimate 
reasons. Instead of chasing them down all (which we will never be able to do 
as we're talking about driver code), we should make sure that media_device 
gets properly refcounted and only freed when safe.

We could in theory implement refcounting in the drivers, by implementing 
.release() handler for all the structure that hold a reference to media_device 
(v4l2_device, videodev and v4l2_subdev as explained above). The drivers would 
then need to count how many of those structures are still in use (as a driver 
can create multiple video nodes and/or subdev nodes for instance) and only 
free the media_device when that counter reaches 0.

That would however be really really wrong, as it would require complex code 
very prone to race conditions (anyone who has worked with USB devices should 
know that) in all drivers, including platform drivers whose unbind gets rarely 
tested. We should instead simplify it for drivers and implement that reference 
counting in the core.

> I have a half-baked patch for (2). I'll try to finish it and do some
> tests.
> 
> Unfortunately, I don't have any OMAP3 device that has a camera
> module, except for a N9 device with a damaged display.
> 
> Sakari,
> 
> Is there a way for me to use the N9 device to test it without a
> display? AFAIKT, the device is operational, and I *guess* it is
> on developer's mode, but not really sure.

-- 
Regards,

Laurent Pinchart

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Greg KH]

On Thu, Dec 15, 2016 at 10:57:16AM -0200, Mauro Carvalho Chehab wrote:
> Em Thu, 15 Dec 2016 09:42:35 -0300
> Javier Martinez Canillas <javier@osg.samsung.com> escreveu:
> 
> > Hello Mauro,
> > 
> > On 12/15/2016 09:37 AM, Mauro Carvalho Chehab wrote:
> > 
> > [snip]
> > 
> > > 
> > > What happens is that omap3isp driver calls media_device_unregister()
> > > too early. Right now, it is called at omap3isp_video_device_release(),
> > > with happens when a driver unbind is ordered by userspace, and not after
> > > the last usage of all /dev/video?? devices.
> > > 
> > > There are two possible fixes:
> > > 
> > > 1) at omap3isp_video_device_release(), streamoff all streams and mark
> > > that the media device will be gone.
> 
> I actually meant to say: isp_unregister_entities() here.
> 
> > > 
> > > 2) instead of using video_device_release_empty for the video->video.release,
> > > create a omap3isp_video_device_release() that will call
> > > media_device_unregister() when destroying the last /dev/video?? devnode.
> > >  
> > 
> > There's also option (3), to have a proper refcounting to make sure that
> > the media device node is not freed until all references to it are gone.
> 
> Yes, that's another alternative.
> 
> > I understand that's what Sakari's RFC patches do. I'll try to make some
> > time tomorrow to test and review his patches.
> 
> The biggest problem with Sakari's patches is that it starts by 
> reverting 3 patches, and this will cause regressions on existing
> devices.
> 
> Development should be incremental.

How can reverting patches cause regressions?  If a patch that is applied
breaks something else, it needs to be reverted, end of story.  If that
patch happened to have fixed a different issue, that's fine, we are back
to the original issue, it's not a "regression" at all, the patch was
wrong in the first place.

So please, just revert them now.  That's the correct thing to do, as we
will be back to the previous release's behavior.

thanks,

greg k-h

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Laurent Pinchart]

Hi Mauro,

On Thursday 15 Dec 2016 10:57:16 Mauro Carvalho Chehab wrote:
> Em Thu, 15 Dec 2016 09:42:35 -0300 Javier Martinez Canillas escreveu:
> > On 12/15/2016 09:37 AM, Mauro Carvalho Chehab wrote:
> > 
> > [snip]
> > 
> >> What happens is that omap3isp driver calls media_device_unregister()
> >> too early. Right now, it is called at omap3isp_video_device_release(),
> >> with happens when a driver unbind is ordered by userspace, and not after
> >> the last usage of all /dev/video?? devices.
> >> 
> >> There are two possible fixes:
> >> 
> >> 1) at omap3isp_video_device_release(), streamoff all streams and mark
> >> that the media device will be gone.
> 
> I actually meant to say: isp_unregister_entities() here.
> 
> >> 2) instead of using video_device_release_empty for the
> >> video->video.release, create a omap3isp_video_device_release() that
> >> will call media_device_unregister() when destroying the last /dev/video??
> >> devnode.
> > 
> > There's also option (3), to have a proper refcounting to make sure that
> > the media device node is not freed until all references to it are gone.
> 
> Yes, that's another alternative.

And I think that's the only one that will bring us sanity in the long term.

> > I understand that's what Sakari's RFC patches do. I'll try to make some
> > time tomorrow to test and review his patches.
> 
> The biggest problem with Sakari's patches is that it starts by
> reverting 3 patches, and this will cause regressions on existing
> devices.
> 
> Development should be incremental.

Yes, it should, but there's also a reason git has a revert command. When 
patches are broken they should be reverted. Broken means that they do more 
harm than good. This is usually understood as introducing a bug worse than the 
gain the patch is supposed to bring. Broken can also mean that the patch makes 
incremental development of a proper solution very difficult while still 
failing to fix the initial problem completely. I believe the three patches in 
question fall into that category. And let's not take this personally, I don't 
care who have authored them, and there's certainly no shame getting a patch 
reverted. It should be considered as a review that comes after merge, it might 
not be the most pleasant one, but we I'm sure we all appreciate how reviews 
help use avoiding the same mistakes in the future and improving ourselves.

> I didn't review carefully his series (as it started the wrong way),

Please review it, as we need to get an agreement on the direction we want to 
take. Then we can discuss whether the reverts are really such a problem. I 
don't think inflicting ourselves the pain that would come with pure 
incremental development would bring us anything good, especially if we 
consider that we'll merge the reverts with the patch series that fixes the 
problem, so we're talking about bisection of unbind code paths that remained 
broken for years before the attempted fix, and are still broken with it as 
current code is racy anyway.

> but I guess there's another problem on it: as OMAP3 remove entities
> at isp_unregister_entities(), while adding a kref to media_device
> will prevent an oops, the streamoff logic won't work anymore, as
> the entities that were supposed to be at the graph will have been
> removed by then.

We need to fix drivers, that's for sure, and we're working on the OMAP3 ISP 
driver first as a proof of concept.

> Ok, we can roll the snow ball and add kref's to entities and links,
> but IMHO, we're trying to kill a fly with a death star: instead,
> the better is to just fix the driver in a way that it would be
> streaming off everything at isp_unregister_entities(), before
> dropping the entities and the media controller.

That won't be enough. Even if you're not entirely convinced by the reasons 
explained in this mail thread, remember that we will need sooner or later to 
implement support for media graph update at runtime. Refcounting will be 
needed, let's design it in the cleanest possible way.

-- 
Regards,

Laurent Pinchart

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Mauro Carvalho Chehab]

Greg,

Em Thu, 15 Dec 2016 05:44:38 -0800
Greg KH <greg@kroah.com> escreveu:

> On Thu, Dec 15, 2016 at 10:57:16AM -0200, Mauro Carvalho Chehab wrote:
> > Em Thu, 15 Dec 2016 09:42:35 -0300
> > Javier Martinez Canillas <javier@osg.samsung.com> escreveu:
> >   
> > > Hello Mauro,
> > > 
> > > On 12/15/2016 09:37 AM, Mauro Carvalho Chehab wrote:
> > > 
> > > [snip]
> > >   
> > > > 
> > > > What happens is that omap3isp driver calls media_device_unregister()
> > > > too early. Right now, it is called at omap3isp_video_device_release(),
> > > > with happens when a driver unbind is ordered by userspace, and not after
> > > > the last usage of all /dev/video?? devices.
> > > > 
> > > > There are two possible fixes:
> > > > 
> > > > 1) at omap3isp_video_device_release(), streamoff all streams and mark
> > > > that the media device will be gone.  
> > 
> > I actually meant to say: isp_unregister_entities() here.
> >   
> > > > 
> > > > 2) instead of using video_device_release_empty for the video->video.release,
> > > > create a omap3isp_video_device_release() that will call
> > > > media_device_unregister() when destroying the last /dev/video?? devnode.
> > > >    
> > > 
> > > There's also option (3), to have a proper refcounting to make sure that
> > > the media device node is not freed until all references to it are gone.  
> > 
> > Yes, that's another alternative.
> >   
> > > I understand that's what Sakari's RFC patches do. I'll try to make some
> > > time tomorrow to test and review his patches.  
> > 
> > The biggest problem with Sakari's patches is that it starts by 
> > reverting 3 patches, and this will cause regressions on existing
> > devices.
> > 
> > Development should be incremental.  
> 
> How can reverting patches cause regressions?  If a patch that is applied
> breaks something else, it needs to be reverted, end of story.  If that
> patch happened to have fixed a different issue, that's fine, we are back
> to the original issue, it's not a "regression" at all, the patch was
> wrong in the first place.
> 
> So please, just revert them now.  That's the correct thing to do, as we
> will be back to the previous release's behavior.

The patches that Sakari want to revert are fixes. Before those patches, the
cdev logic was broken. So, it used to generate OOPS when the media
character device is removed.

So, when PCI/USB drivers gained media controller support, a regression
was introduced. Those patches fix it, as without them, unbinding
(or physically removing) PCI/USB devices cause OOPS because the cdev logic
there are broken.

What happens is that Sakari is proposing a different approach to
solve it on this 21 RFC patch series. Instead of applying his solution
on the top of upstream code, he decided to start it by removing the
regression fix patches.

Also, the way his solution was designed, every single media driver using 
the media controller needs to be modified in order for it to not cause OOPS
at device unbind. However, the series only do such changes on OMAP3
driver (and no te didn't make any tests on this series out of OMAP3). 

So, applying the entire series will very likely cause regressions
on PCI/USB drivers.

Thanks,
Mauro

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Laurent Pinchart]

Hi Greg,

On Thursday 15 Dec 2016 04:31:12 Greg KH wrote:
> On Thu, Dec 15, 2016 at 02:13:42PM +0200, Laurent Pinchart wrote:
> > Hi Mauro,
> > 
> > (CC'ing Greg)
> > 
> > On Wednesday 14 Dec 2016 13:14:06 Mauro Carvalho Chehab wrote:
> > > Avoid calling streamoff without having the media structs allocated.
> > > 
> > > Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
> > 
> > The driver has a maintainer listed in MAINTAINERS, and you know that
> > Sakari is also actively involved here. You could have CC'ed us.
> > 
> > > ---
> > > 
> > > Javier,
> > > 
> > > Could you please test this patch?
> > > 
> > > Thanks!
> > > Mauro
> > > 
> > >  drivers/media/platform/omap3isp/ispvideo.c | 10 ++++++++--
> > >  1 file changed, 8 insertions(+), 2 deletions(-)
> > > 
> > > diff --git a/drivers/media/platform/omap3isp/ispvideo.c
> > > b/drivers/media/platform/omap3isp/ispvideo.c index
> > > 7354469670b7..f60995ed0a1f 100644
> > > --- a/drivers/media/platform/omap3isp/ispvideo.c
> > > +++ b/drivers/media/platform/omap3isp/ispvideo.c
> > > @@ -1488,11 +1488,17 @@ int omap3isp_video_register(struct isp_video
> > > *video, struct v4l2_device *vdev) "%s: could not register video device
> > > (%d)\n",> > 
> > >  			__func__, ret);
> > > 
> > > +	/* Prevent destroying MC before unregistering */
> > > +	kobject_get(vdev->v4l2_dev->mdev->devnode->dev.parent);
> > 
> > This doesn't even compile. Please make sure to at least compile-test
> > patches you send for review, otherwise you end up wasting time for all
> > reviewers and testers. I assume you meant
> > 
> > 	kobject_get(&vdev->mdev->devnode->dev.parent->kobj);
> > 
> > and similarly below.
> > 
> > That's a long list of pointer dereferences, going deep down the device
> > core. Greg, are drivers allowed to do this by the driver model ?
> 
> WTF?
> 
> Eeek, no no no no!
> 
> First off, no driver should EVER have to call a "raw" kobject call,
> that's a huge sign that you are doing something really really wrong.
> 
> Secondly, you NEVER grab a reference to a structure like this, you use
> the "correct" driver/bus api calls.
> 
> Thirdly, ugh, how to say this nicely...  The whole idea that something
> like this could actually be a real solution to a problem is insane.
> 
> Look at what you are really doing here, trying to grab an extra
> reference on something that in reality, should never go away anyhow.
> Your parent structure should already always have the reference count
> incremented and will not disappear underneath you at all.  And if this
> isn't your "parent", you have no right at all to go grab random
> references across the device tree for no reason other than you feel you
> don't want it to go away.  If you don't want something to go away, you
> properly get the reference (hint, you already should have if you have
> this type of pointer chain to the object.)
> 
> If this type of solution is somehow the "correct" one, the v4l driver
> model interaction is severely broken and needs to be fixed.
> 
> What bug is this that caused this type of hack to even be proposed?  Is
> it a bug or a regression?  If a regression, can someone show me the
> commit that would cause such a monstrosity to be proposed?
> 
> Laurent, sorry, I know I said I was going to debug a USB V4L reference
> counting problem last week, I had to travel and haven't had the chance
> to do so.  I'll try to get to it today.  Hopefully that issue has
> nothing to do with this problem.  Because if so, ugh...

No worries, it's not urgent. The problem has nothing to do with this. I've 
used the uvcvideo driver to trigger it, but it's probably independent of V4L2 
(although sometimes I'm beginning to wonder :-)).

> Mauro, again, please never propose something like this again.

-- 
Regards,

Laurent Pinchart

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Mauro Carvalho Chehab]

Em Thu, 15 Dec 2016 04:31:12 -0800
Greg KH <greg@kroah.com> escreveu:

> On Thu, Dec 15, 2016 at 02:13:42PM +0200, Laurent Pinchart wrote:
> > Hi Mauro,
> > 
> > (CC'ing Greg)
> > 
> > On Wednesday 14 Dec 2016 13:14:06 Mauro Carvalho Chehab wrote:  
> > > Avoid calling streamoff without having the media structs allocated.
> > > 
> > > Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>  
> > 
> > The driver has a maintainer listed in MAINTAINERS, and you know that Sakari is 
> > also actively involved here. You could have CC'ed us.
> >   
> > > ---
> > > 
> > > Javier,
> > > 
> > > Could you please test this patch?
> > > 
> > > Thanks!
> > > Mauro
> > > 
> > >  drivers/media/platform/omap3isp/ispvideo.c | 10 ++++++++--
> > >  1 file changed, 8 insertions(+), 2 deletions(-)
> > > 
> > > diff --git a/drivers/media/platform/omap3isp/ispvideo.c
> > > b/drivers/media/platform/omap3isp/ispvideo.c index
> > > 7354469670b7..f60995ed0a1f 100644
> > > --- a/drivers/media/platform/omap3isp/ispvideo.c
> > > +++ b/drivers/media/platform/omap3isp/ispvideo.c
> > > @@ -1488,11 +1488,17 @@ int omap3isp_video_register(struct isp_video *video,
> > > struct v4l2_device *vdev) "%s: could not register video device (%d)\n",
> > >  			__func__, ret);
> > > 
> > > +	/* Prevent destroying MC before unregistering */
> > > +	kobject_get(vdev->v4l2_dev->mdev->devnode->dev.parent);  
> > 
> > This doesn't even compile. Please make sure to at least compile-test patches 
> > you send for review, otherwise you end up wasting time for all reviewers and 
> > testers. I assume you meant
> > 
> > 	kobject_get(&vdev->mdev->devnode->dev.parent->kobj);
> > 
> > and similarly below.
> > 
> > That's a long list of pointer dereferences, going deep down the device core. 
> > Greg, are drivers allowed to do this by the driver model ?  
> 
> WTF?
> 
> Eeek, no no no no!
> 
> First off, no driver should EVER have to call a "raw" kobject call,
> that's a huge sign that you are doing something really really wrong.
> 
> Secondly, you NEVER grab a reference to a structure like this, you use
> the "correct" driver/bus api calls.
> 
> Thirdly, ugh, how to say this nicely...  The whole idea that something
> like this could actually be a real solution to a problem is insane.

Greg,

This patch is generating a lot of noise for no good reason.

It was meant to be sent just to Javier, as I currently don't have a working
OMAP3 board with V4L2 hardware.

Unfortunately, I have this on my .git/config, and it ended by being
sent to the public ML as well by mistake:

	[format]
		numbered = auto
	to = Linux Media Mailing List <linux-media@vger.kernel.org>

> Look at what you are really doing here, trying to grab an extra
> reference on something that in reality, should never go away anyhow.
> Your parent structure should already always have the reference count
> incremented and will not disappear underneath you at all.  And if this
> isn't your "parent", you have no right at all to go grab random
> references across the device tree for no reason other than you feel you
> don't want it to go away.  If you don't want something to go away, you
> properly get the reference (hint, you already should have if you have
> this type of pointer chain to the object.)
>
> If this type of solution is somehow the "correct" one, the v4l driver
> model interaction is severely broken and needs to be fixed.
> 

The problem here is that the Nokia N9 hardware (with uses the omap3 isp
driver) drops the /dev/media device and all associated structures too early
if unbound.

Btw, it is not clear to me why userspace would want to unbind the
V4L2 driver on such hardware, as it is not hot-pluggable.

> What bug is this that caused this type of hack to even be proposed?  Is
> it a bug or a regression?  If a regression, can someone show me the
> commit that would cause such a monstrosity to be proposed?

It is a bug, since day zero. That's why reverting patches won't fix
anything. The problem happens when the device is streaming on one (or more)
of their /dev/video?? devnodes, and it is requested to unbound
(either by removing the module or by accessing the module unbind via sysfs.

The way OMAP3 driver's code does is:

At .probe(), the OMAP3 isp driver creates a struct media_device that
it is used by other OMAP3 drivers to store the hardware setup used to
stream video inside a list. It also creates a struct media_devnode
with embeeds struct cdev to control the media pipelines, via /dev/media0.

Originally, struct media_devnode were embedded at struct media_device.
Now, media_devnode is allocated dynamically, allowing the removal of
/dev/media0 without freeing struct media_device[1].

In any case, the unbind code doesn't have any special logic to handle
disconnections.

So, when an unbind is requested, the device the device driver will free
all the data associated with struct media_device, including the hardware
setup.

It will also destroy struct media_devnode, if not used anymore (with
the current code, this is properly protected via struct device kref).

Later on, when /dev/video?? is closed, the .release() fops callback
will call the streamoff code, with depends on the data that were
freed earlier.

There are some solutions for this bug:

1) stop streaming at unbind - something similar to what we do on USB
   drivers with the .disconnect() calls, where we stop URBs and
   don't accept the driver to stream on again;

2) add a kref inside the OMAP3 driver that would only call the
   code that releases struct media_device when the last /dev/video??
   device is closed.

3) add kref for all data used by the OMAP3 driver: struct media_device,
   struct media_entity, struct media_link, ... (we could eventually
   embed it at struct media_gobj - as I proposed in mid 2015).

[1] The three patches that Sakari proposed to remove on his RFC series,
without explaining why, are those that allocate media_devnode dynamically.

> Laurent, sorry, I know I said I was going to debug a USB V4L reference
> counting problem last week, I had to travel and haven't had the chance
> to do so.  I'll try to get to it today.  Hopefully that issue has
> nothing to do with this problem.  Because if so, ugh...
> 
> Mauro, again, please never propose something like this again.
> 
> greg k-h

Thanks,
Mauro

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Sakari Ailus]

Hi Mauro and Greg,

On Thu, Dec 15, 2016 at 12:17:58PM -0200, Mauro Carvalho Chehab wrote:
> Greg,
> 
> Em Thu, 15 Dec 2016 05:44:38 -0800
> Greg KH <greg@kroah.com> escreveu:
> 
> > On Thu, Dec 15, 2016 at 10:57:16AM -0200, Mauro Carvalho Chehab wrote:
> > > Em Thu, 15 Dec 2016 09:42:35 -0300
> > > Javier Martinez Canillas <javier@osg.samsung.com> escreveu:
> > >   
> > > > Hello Mauro,
> > > > 
> > > > On 12/15/2016 09:37 AM, Mauro Carvalho Chehab wrote:
> > > > 
> > > > [snip]
> > > >   
> > > > > 
> > > > > What happens is that omap3isp driver calls media_device_unregister()
> > > > > too early. Right now, it is called at omap3isp_video_device_release(),
> > > > > with happens when a driver unbind is ordered by userspace, and not after
> > > > > the last usage of all /dev/video?? devices.
> > > > > 
> > > > > There are two possible fixes:
> > > > > 
> > > > > 1) at omap3isp_video_device_release(), streamoff all streams and mark
> > > > > that the media device will be gone.  
> > > 
> > > I actually meant to say: isp_unregister_entities() here.
> > >   
> > > > > 
> > > > > 2) instead of using video_device_release_empty for the video->video.release,
> > > > > create a omap3isp_video_device_release() that will call
> > > > > media_device_unregister() when destroying the last /dev/video?? devnode.
> > > > >    
> > > > 
> > > > There's also option (3), to have a proper refcounting to make sure that
> > > > the media device node is not freed until all references to it are gone.  
> > > 
> > > Yes, that's another alternative.
> > >   
> > > > I understand that's what Sakari's RFC patches do. I'll try to make some
> > > > time tomorrow to test and review his patches.  
> > > 
> > > The biggest problem with Sakari's patches is that it starts by 
> > > reverting 3 patches, and this will cause regressions on existing
> > > devices.
> > > 
> > > Development should be incremental.  
> > 
> > How can reverting patches cause regressions?  If a patch that is applied
> > breaks something else, it needs to be reverted, end of story.  If that
> > patch happened to have fixed a different issue, that's fine, we are back
> > to the original issue, it's not a "regression" at all, the patch was
> > wrong in the first place.
> > 
> > So please, just revert them now.  That's the correct thing to do, as we
> > will be back to the previous release's behavior.
> 
> The patches that Sakari want to revert are fixes. Before those patches, the
> cdev logic was broken. So, it used to generate OOPS when the media
> character device is removed.

I'd rather call them workarounds. They cause other issues (see below the
reply) and there are unaddressed review comments. They were still applied
because there was no good solution available at the time.

<URL:http://www.spinics.net/lists/kernel/msg2281365.html>
<URL:https://www.spinics.net/lists/linux-media/msg100355.html>
<URL:https://www.spinics.net/lists/linux-media/msg100927.html>
<URL:https://www.spinics.net/lists/linux-media/msg100936.html>
<URL:https://www.spinics.net/lists/linux-media/msg100952.html>
<URL:https://www.spinics.net/lists/linux-media/msg101028.html>

At least some of the issues the patches claim to fix are really not fixed
either. They are just made slightly less likely to accidentally stumble
upon.

> 
> So, when PCI/USB drivers gained media controller support, a regression
> was introduced. Those patches fix it, as without them, unbinding
> (or physically removing) PCI/USB devices cause OOPS because the cdev logic
> there are broken.
> 
> What happens is that Sakari is proposing a different approach to
> solve it on this 21 RFC patch series. Instead of applying his solution
> on the top of upstream code, he decided to start it by removing the
> regression fix patches.

The problems always existed, we just did not pay much attention to them, for
the reason you stated above. Instead of trying to fend off user space
accessing the device through IOCTL calls (which are _not_ serialised with
releasing of the data structures the IOCTL calls operate on), one really
must make sure the device is not being accessed from the user space through
e.g. IOCTLs while its memory is being released.

On V4L2 there's a release() callback to do that, on Media controller we
still have nothing --- something that's added by my RFC patchset. And yes,
it's still RFC and requires modifications, but it's not reasonable to
outright reject it (or not to review it) on the grounds that an unagreed
Media controller core API change isn't yet implemented for all potentially
affected drivers. Existing drivers still work without API changes, with the
caveat that they do have the same object lifetime issues which they did
before.

> 
> Also, the way his solution was designed, every single media driver using 
> the media controller needs to be modified in order for it to not cause OOPS
> at device unbind. However, the series only do such changes on OMAP3
> driver (and no te didn't make any tests on this series out of OMAP3). 

I use omap3isp as an example as it's a good example: it's relatively well
written and uses sub-devices implemented by external drivers with V4L2,
Media controller and V4L2 sub-device nodes, so it exhibits most of the
issues in the problem domain. I also have the hardware so I can test it, I
understand Shuah and Laurent have one as well.

> 
> So, applying the entire series will very likely cause regressions
> on PCI/USB drivers.

It's not intended to be applied as it is. This is why it's posted as RFC.

Quoting myself (with added commit id for the third patch, full thread here):

<URL:http://www.spinics.net/lists/linux-media/msg107844.html>

> The patches are in fact on top of the current media-tree, or were when they
> were sent (v4).
> 
> The reason I'm reverting patches is that the reason why these patches were
> merged was not because they would have been a sound way forward for the
> Media controller framework, but because they partially worked around issues
> in a device being in use while it was removed.
> 
> They never were a complete fix for these problems nor I do think they could
> be extended to be such. There were also unaddressed issues in these patches
> pointed out during the review. For these reasons I'm reverting the three
> patches. In more detail:
> 
> * media: fix media devnode ioctl/syscall and unregister race
>   6f0dd24a084a
> 
> The patch clears the registered bit before performing the steps related to
> unregistering a media device, but the bit is checked only at the beginning
> of the IOCTL call. As unregistering a device and an IOCTL call on a file
> handle of that device are not serialised, nothing guarantees the IOCTL call
> will finish with the registered bit still in the same state. Serialising the
> two e.g. by using a mutex is hardly a feasible solution for this.
> 
> I may have pointed out the original problem but this is not the solution.
> 
> <URL:http://www.spinics.net/lists/linux-media/msg101295.html>
> 
> The right solution is instead to make sure the data structures related to
> the media device will not disappear while the IOCTL call is in progress (at
> least).
> 
> * media: fix use-after-free in cdev_put() when app exits after driver unbind
>   5b28dde51d0c
> 
> The patch avoids the problem of deleting a character device (cdev_del())
> after its memory has been released. The change is sound as such but the
> problem is addressed by another, a lot more simple patch in my series:
> 
> <URL:http://git.retiisi.org.uk/?p=~sailus/linux.git;a=commitdiff;h=26fa8c1a3df5859d34cef8ef953e3a29a432a17b>
> 
> It might be possible to reasonably continue from here if the next patch to
> be reverted did not depend on this one.
> 
> * media-device: dynamically allocate struct media_devnode
>   a087ce704b80
> 
> This creates a two-way dependency between struct media_devnode and
> media_device. This is very much against the original design which clearly
> separates the two: media_devnode is entirely independent of media_device.
> 
> The original intent was that another sub-system in the kernel such as the
> V4L2 could make use of media_devnode as well and while that hasn't happened,
> perhaps the two could be merged. There simply are no other reasons to keep
> the two structs separate.
> 
> The patch is certainly a workaround, as it (partially, again) works around
> issues in timing of releasing memory and accessing it.
> 
> The proper solutions regarding the media_device and media_devnode are either
> maintain the separation or unify the two, and this patch does nor suggests
> either of these. To the contrary: it makes either of these impossible by
> design, and this reason alone is enough to revert it.
> 
> The set I'm pushing maintains the separation and leaves the option of either
> merging the two (media_device and media_devnode) or making use of
> media_devnode elsewhere open.

-- 
Kind regards,

Sakari Ailus
e-mail: sakari.ailus@iki.fi	XMPP: sailus@retiisi.org.uk

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Mauro Carvalho Chehab]

Em Thu, 15 Dec 2016 16:04:51 +0200
Laurent Pinchart <laurent.pinchart@ideasonboard.com> escreveu:

We have now two threads discussing the same subject, which is bad, as
we'll end repeating the same arguments on different threads...

Let's use the "[PATCH RFC 00/21]" for those discussions, as it seems we're
reaching to somewhere there.

> Even if you're not entirely convinced by the reasons 
> explained in this mail thread, remember that we will need sooner or later to 
> implement support for media graph update at runtime. Refcounting will be 
> needed, let's design it in the cleanest possible way.

As I said, I'm not against using some other approach and even
adding refcounting to each graph object.

What I am against is on a patchset that starts by breaking 
the USB drivers that use the media controller.

Btw, I'm starting to suspect that getting rid of devm_*alloc()
on OMAP3, as proposed by the 00/21 thread is addressing a symptom of
the problem and not a cause, and that using get_device()/put_device()
may help fixing such issues. See Hans comments on that thread.

Thanks,
Mauro

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Sakari Ailus]

[-- Attachment #1: Type: text/plain, Size: 6695 bytes --]

Hi folks,

On Fri, Dec 16, 2016 at 10:21:25AM +0200, Sakari Ailus wrote:
...
> At least some of the issues the patches claim to fix are really not fixed
> either. They are just made slightly less likely to accidentally stumble
> upon.

I couldn't immediately trigger this with the current mainline kernel as the
remaining time window isn't very large. However making this trivial-looking
change:

diff --git a/drivers/media/media-devnode.c b/drivers/media/media-devnode.c
index f2772ba..6ec4125 100644
--- a/drivers/media/media-devnode.c
+++ b/drivers/media/media-devnode.c
@@ -32,6 +32,7 @@
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
 
+#include <linux/delay.h>
 #include <linux/errno.h>
 #include <linux/init.h>
 #include <linux/module.h>
@@ -128,6 +129,8 @@ __media_ioctl(struct file *filp, unsigned int cmd, unsigned long arg,
        if (!media_devnode_is_registered(devnode))
                return -EIO;
 
+       msleep(1000);
+
        return ioctl_func(filp, cmd, arg);
 }
 
And calling MEDIA_IOC_ENUM_ENTITIES (for instance) in a loop (v4l-utils):

diff --git a/utils/media-ctl/libmediactl.c b/utils/media-ctl/libmediactl.c
index 1fd6525..5be3cea 100644
--- a/utils/media-ctl/libmediactl.c
+++ b/utils/media-ctl/libmediactl.c
@@ -522,7 +522,7 @@ static int media_enum_entities(struct media_device *media)
 		entity->fd = -1;
 		entity->info.id = id | MEDIA_ENT_ID_FLAG_NEXT;
 		entity->media = media;
-
+while (1)
 		ret = ioctl(media->fd, MEDIA_IOC_ENUM_ENTITIES, &entity->info);
 		if (ret < 0) {
 			ret = errno != EINVAL ? -errno : 0;


And then unbinding the omap3-isp driver will immediately produce this. The
same would take place on any driver implementing the Media controller
interface. What happens there is that the memory backing the media device
has been released while the IOCTL call was in progress. This can happen
because device removal and IOCTL calls are not serialised nor the media
device is reference counted --- the latter of which I believe is the right
thing to do:

[  105.756408] Unable to handle kernel NULL pointer dereference at virtual address 00000140
[  105.756561] pgd = eda94000
[  105.756591] [00000140] *pgd=adaf8831, *pte=00000000, *ppte=00000000
[  105.756683] Internal error: Oops: 17 [#1] PREEMPT ARM
[  105.756744] Modules linked in: smiapp smiapp_pll omap3_isp videobuf2_dma_contig videobuf2_memops videobuf2_v4l2 videobuf2_core v4l2_common videodev media
[  105.756927] CPU: 0 PID: 2276 Comm: media-ctl Not tainted 4.9.0-rc6-00494-g9244e38-dirty #830
[  105.757019] Hardware name: Generic OMAP36xx (Flattened Device Tree)
[  105.757080] task: ed970380 task.stack: eda5e000
[  105.757141] PC is at __lock_acquire+0x94/0x1868
[  105.757202] LR is at lock_acquire+0x70/0x90
[  105.757263] pc : [<c015e9a8>]    lr : [<c01601ec>]    psr: 20000093
               sp : eda5fcc0  ip : eda5e000  fp : 00000000
[  105.757354] r10: 00000001  r9 : 00000000  r8 : 0002715c
[  105.757415] r7 : 00000140  r6 : 00000001  r5 : 60000013  r4 : ed970380
[  105.757476] r3 : 00000001  r2 : 00000001  r1 : 00000000  r0 : 00000140
[  105.757537] Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment none
[  105.757629] Control: 10c5387d  Table: ada94019  DAC: 00000051
[  105.757690] Process media-ctl (pid: 2276, stack limit = 0xeda5e208)
[  105.757751] Stack: (0xeda5fcc0 to 0xeda60000)
[  105.757812] fcc0: ed970868 00000001 a409df10 c355d08b c0c75714 c01602f4 60000013 00000001
[  105.757904] fce0: ee1c9514 c0839b48 ee1c9518 effed360 ed970868 60000013 c0833e74 c0839b48
[  105.757995] fd00: effed360 effed360 c0e9166c ee1c951c ee1c9518 00000000 60000013 00000001
[  105.758087] fd20: 00000000 0002715c eda5e000 00000000 00000000 c01601ec 00000001 00000000
[  105.758178] fd40: 00000000 bf000e78 00000000 00000000 0000010c bf000e78 ed970380 c04ed214
[  105.758270] fd60: 00000001 00000000 bf000e78 c015aa50 ed9703b0 ed9703b0 c0830d50 00000000
[  105.758361] fd80: ed970848 c0830d60 ed970380 ed970380 c0830d60 c01602f4 c0e76744 00000051
[  105.758483] fda0: eda5fdd0 00000000 0002715c eda5fdd0 bf002e28 c1007c01 00000000 0002715c
[  105.758575] fdc0: eda5e000 00000000 00000000 bf000e78 00000001 50414d4f 53492033 43432050
[  105.758666] fde0: 00003250 00000000 00000000 00000000 00000000 00020000 00000000 00000000
[  105.758758] fe00: 00000000 00010002 00000000 00000000 00000000 00000000 00000051 00000007
[  105.758850] fe20: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  105.758941] fe40: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  105.759033] fe60: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  105.759124] fe80: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  105.759216] fea0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  105.759307] fec0: 00000000 00000000 00000000 00000000 ed967c80 bf000ddc ed967c80 0002715c
[  105.759399] fee0: c1007c01 00000003 00000000 bf001808 0002715c ed967c80 00000003 ed9fece0
[  105.759490] ff00: 00000003 c01ea4c4 0002715c c01eb4a8 00000000 00000000 c01fba18 ffffffff
[  105.759582] ff20: 00000001 00000000 ee84f010 ed89e440 00000000 ee2654e8 00000010 c01dacdc
[  105.759674] ff40: 00000000 00000000 00000000 ed89e538 ed8a2b50 ed9707a0 ed970380 00000000
[  105.759765] ff60: eda5ff7c eda5ff84 ed967c80 ed967c80 0002715c c1007c01 00000003 eda5e000
[  105.759857] ff80: 00000000 c01eb560 0002715c 00027008 00000000 00000036 c0107d84 eda5e000
[  105.759948] ffa0: 00000000 c0107be0 0002715c 00027008 00000003 c1007c01 0002715c 80000000
[  105.760070] ffc0: 0002715c 00027008 00000000 00000036 00027158 00000000 b6f71000 00000000
[  105.760162] ffe0: 00026b08 be9cf85c 000126a4 b6eaaa5c 20000010 00000003 fda7fddf fdbdffba
[  105.760253] [<c015e9a8>] (__lock_acquire) from [<c01601ec>] (lock_acquire+0x70/0x90)
[  105.760375] [<c01601ec>] (lock_acquire) from [<c04ed214>] (mutex_lock_nested+0x54/0x3f4)
[  105.760528] [<c04ed214>] (mutex_lock_nested) from [<bf000e78>] (media_device_ioctl+0x9c/0x120 [media])
[  105.760681] [<bf000e78>] (media_device_ioctl [media]) from [<bf001808>] (media_ioctl+0x54/0x60 [media])
[  105.760803] [<bf001808>] (media_ioctl [media]) from [<c01ea4c4>] (vfs_ioctl+0x18/0x30)
[  105.760894] [<c01ea4c4>] (vfs_ioctl) from [<c01eb4a8>] (do_vfs_ioctl+0x90c/0x974)
[  105.760986] [<c01eb4a8>] (do_vfs_ioctl) from [<c01eb560>] (SyS_ioctl+0x50/0x6c)
[  105.761108] [<c01eb560>] (SyS_ioctl) from [<c0107be0>] (ret_fast_syscall+0x0/0x1c)
[  105.761199] Code: e59f3f58 e593300c e3530000 0a000003 (e5972000) 
[  105.761260] ---[ end trace bdb47e9a97e34f03 ]---

-- 
Regards,

Sakari Ailus
e-mail: sakari.ailus@iki.fi	XMPP: sailus@retiisi.org.uk

[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 73687 bytes --]

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.0-rc6-00494-g9244e38-dirty (sakke@lanttu) (gcc version 4.4.5 (Debian 4.4.5-8) ) #830 PREEMPT Fri Dec 16 13:05:56 EET 2016
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt:Machine model: Nokia N9
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 261632
[    0.000000] free_area_init_node: node 0, pgdat c0862d18, node_mem_map ef7f9000
[    0.000000]   Normal zone: 1536 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 196608 pages, LIFO batch:31
[    0.000000]   HighMem zone: 65024 pages, LIFO batch:15
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk)
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
[    0.000000] Kernel command line: ip=192.168.1.130::192.168.1.129:::usb0:off root=/dev/nfs nfsroot=192.168.1.129:/scratch/rootfs/laiskiainen rootdelay=5 rw console=tty0 console=ttyS0,115200n8 musb_core.debug=1 musb_hdrc.debug=2 musb.debug=3 loglevel=8
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1020796K/1046528K available (4096K kernel code, 423K rwdata, 1520K rodata, 1024K init, 8748K bss, 25732K reserved, 0K cma-reserved, 260096K highmem)
[    0.000000] Virtual kernel memory layout:
                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                   fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
                   vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
                   lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
                   pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
                   modules : 0xbf000000 - 0xbfe00000   (  14 MB)
                     .text : 0xc0008000 - 0xc0500000   (5088 kB)
                     .init : 0xc0700000 - 0xc0800000   (1024 kB)
                     .data : 0xc0800000 - 0xc0869ee0   ( 424 kB)
                      .bss : 0xc086b000 - 0xc10f60ac   (8749 kB)
[    0.000000] Running RCU self tests
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU lockdep checking is enabled.
[    0.000000] 	Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[    0.000000] kmemleak: Kernel memory leak detector disabled
[    0.000000] Clocking rate (Crystal/Core/MPU): 38.4/390/600 MHz
[    0.000000] OMAP clockevent source: timer1 at 32768 Hz
[    0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns
[    0.000030] OMAP clocksource: 32k_counter at 32768 Hz
[    0.001953] Console: colour dummy device 80x30
[    0.007110] console [tty0] enabled
[    0.007171] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.007232] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.007293] ... MAX_LOCK_DEPTH:          48
[    0.007354] ... MAX_LOCKDEP_KEYS:        8191
[    0.007385] ... CLASSHASH_SIZE:          4096
[    0.007446] ... MAX_LOCKDEP_ENTRIES:     32768
[    0.007476] ... MAX_LOCKDEP_CHAINS:      65536
[    0.007537] ... CHAINHASH_SIZE:          32768
[    0.007598]  memory used by lock dependency info: 5167 kB
[    0.007629]  per task-struct memory footprint: 1536 bytes
[    0.012420] kmemleak: Early log buffer exceeded (5729), please increase DEBUG_KMEMLEAK_EARLY_LOG_SIZE
[    0.012603] Calibrating delay loop... 594.73 BogoMIPS (lpj=2973696)
[    0.055450] pid_max: default: 32768 minimum: 301
[    0.056091] Security Framework initialized
[    0.056365] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.056457] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.062133] CPU: Testing write buffer coherency: ok
[    0.064300] Setting up static identity map for 0x80100000 - 0x80100058
[    0.077606] devtmpfs: initialized
[    0.282196] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    0.285186] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.285888] pinctrl core: initialized pinctrl subsystem
[    0.303436] NET: Registered protocol family 16
[    0.305480] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.393951] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp
[    0.396606] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp
[    0.554779] cpuidle: using governor ladder
[    0.584381] cpuidle: using governor menu
[    0.586700] Reprogramming SDRC clock to 390400000 Hz
[    0.622039] gpio gpiochip0: (gpio): added GPIO chardev (254:0)
[    0.626495] gpiochip_setup_dev: registered GPIOs 0 to 31 on device: gpiochip0 (gpio)
[    0.640045] OMAP GPIO hardware version 2.5
[    0.643524] gpio gpiochip1: (gpio): added GPIO chardev (254:1)
[    0.647644] gpiochip_setup_dev: registered GPIOs 32 to 63 on device: gpiochip1 (gpio)
[    0.663696] gpio gpiochip2: (gpio): added GPIO chardev (254:2)
[    0.667083] gpiochip_setup_dev: registered GPIOs 64 to 95 on device: gpiochip2 (gpio)
[    0.683013] gpio gpiochip3: (gpio): added GPIO chardev (254:3)
[    0.686523] gpiochip_setup_dev: registered GPIOs 96 to 127 on device: gpiochip3 (gpio)
[    0.702575] gpio gpiochip4: (gpio): added GPIO chardev (254:4)
[    0.705993] gpiochip_setup_dev: registered GPIOs 128 to 159 on device: gpiochip4 (gpio)
[    0.721832] gpio gpiochip5: (gpio): added GPIO chardev (254:5)
[    0.725341] gpiochip_setup_dev: registered GPIOs 160 to 191 on device: gpiochip5 (gpio)
[    0.803131] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
[    0.803466] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
[    0.803649] gpiochip_find_base: found new base at 508
[    0.803771] gpio gpiochip6: (omap-gpmc): added GPIO chardev (254:6)
[    0.807403] gpiochip_setup_dev: registered GPIOs 508 to 511 on device: gpiochip6 (omap-gpmc)
[    0.831420] omap4_sram_init:Unable to allocate sram needed to handle errata I688
[    0.831542] omap4_sram_init:Unable to get sram pool needed to handle errata I688
[    0.834442] Reserving DMA channels 0 and 1 for HS ROM code
[    0.834533] OMAP DMA hardware revision 5.0
[    1.004791] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixedregulator0[0]' - status (0)
[    1.008300] of_get_named_gpiod_flags: parsed 'gpio' property of node '/fixedregulator2[0]' - status (0)
[    1.021636] omap-iommu 480bd400.mmu: 480bd400.mmu registered
[    1.026275] usbcore: registered new interface driver usbfs
[    1.027130] usbcore: registered new interface driver hub
[    1.028350] usbcore: registered new device driver usb
[    1.039947] omap_i2c 48070000.i2c: bus 0 rev4.4 at 2900 kHz
[    1.045410] omap_i2c 48072000.i2c: bus 1 rev4.4 at 400 kHz
[    1.050048] omap_i2c 48060000.i2c: bus 2 rev4.4 at 400 kHz
[    1.066101] clocksource: Switched to clocksource 32k_counter
[    1.199737] NET: Registered protocol family 2
[    1.204895] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    1.205200] TCP bind hash table entries: 8192 (order: 6, 294912 bytes)
[    1.210479] TCP: Hash tables configured (established 8192 bind 8192)
[    1.212127] UDP hash table entries: 512 (order: 3, 40960 bytes)
[    1.212799] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes)
[    1.214843] NET: Registered protocol family 1
[    1.218505] RPC: Registered named UNIX socket transport module.
[    1.218597] RPC: Registered udp transport module.
[    1.218658] RPC: Registered tcp transport module.
[    1.218688] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.236053] futex hash table entries: 256 (order: 1, 11264 bytes)
[    1.238006] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[    1.250549] bounce: pool size: 64 pages
[    1.250793] io scheduler noop registered
[    1.250854] io scheduler deadline registered
[    1.251068] io scheduler cfq registered (default)
[    1.254730] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568
[    1.255828] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92
[    1.258605] pinctrl-single 480025a0.pinmux: 46 pins at pa fa0025a0 size 92
[    1.267852] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.285034] omap_uart 4806a000.serial: no wakeirq for uart0
[    1.285156] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp@68000000/serial@4806a000[0]'
[    1.287597] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0
[    1.291290] omap_uart 4806c000.serial: no wakeirq for uart1
[    1.291381] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp@68000000/serial@4806c000[0]'
[    1.292175] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP UART1
[    1.295654] omap_uart 49020000.serial: no wakeirq for uart2
[    1.295745] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp@68000000/serial@49020000[0]'
[    1.296600] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2
[    1.300354] omap_uart 49042000.serial: no wakeirq for uart3
[    1.300476] of_get_named_gpiod_flags: can't parse 'rts-gpio' property of node '/ocp@68000000/serial@49042000[0]'
[    1.301269] 49042000.serial: ttyO3 at MMIO 0x49042000 (irq = 96, base_baud = 3000000) is a OMAP UART3
[    1.359130] twl 0-0048: PIH (irq 23) chaining IRQs 336..344
[    1.359741] twl 0-0048: power (irq 341) chaining IRQs 344..351
[    1.376525] random: fast init done
[    1.429595] vmmc2: Bringing 2800000uV into 3000000-3000000uV
[    1.472198] twl4030_gpio twl4030-gpio: gpio (irq 336) chaining IRQs 352..369
[    1.472900] gpiochip_find_base: found new base at 490
[    1.472991] gpio gpiochip7: (twl4030): added GPIO chardev (254:7)
[    1.475769] gpiochip_setup_dev: registered GPIOs 490 to 507 on device: gpiochip7 (twl4030)
[    1.557403] twl4030_usb 48070000.i2c:twl@48:twl4030-usb: Initialized TWL4030 USB module
[    1.600402] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver
[    1.605224] musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 1
[    1.617126] hub 1-0:1.0: USB hub found
[    1.617828] hub 1-0:1.0: 1 port detected
[    1.643218] udc musb-hdrc.0.auto: registering UDC driver [g_ether]
[    1.643768] using random self ethernet address
[    1.643829] using random host ethernet address
[    1.643951] g_ether gadget: adding config #1 'CDC Ethernet (ECM)'/c0857960
[    1.644195] g_ether gadget: adding 'cdc_ethernet'/eeca7f00 to config 'CDC Ethernet (ECM)'/c0857960
[    1.650878] usb0: HOST MAC fa:bf:c4:9f:79:5c
[    1.652374] usb0: MAC c2:16:47:78:17:05
[    1.652587] g_ether gadget: CDC Ethernet: dual speed IN/ep1in OUT/ep1out NOTIFY/ep2in
[    1.652679] g_ether gadget: cfg 1/c0857960 speeds: high full
[    1.652740] g_ether gadget:   interface 0 = cdc_ethernet/eeca7f00
[    1.652801] g_ether gadget:   interface 1 = cdc_ethernet/eeca7f00
[    1.652893] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[    1.652954] g_ether gadget: g_ether ready
[    1.658691] mousedev: PS/2 mouse device common for all mice
[    1.661560] twl4030_keypad 48070000.i2c:twl@48:keypad: OF: linux,keymap property not defined in /ocp@68000000/i2c@48070000/twl@48/keypad
[    1.661712] twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap
[    1.661865] twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -2
[    1.670135] input: twl4030_pwrbutton as /devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl@48:pwrbutton/input/input1
[    1.675292] twl_rtc 48070000.i2c:twl@48:rtc: Enabling TWL-RTC
[    1.682678] twl_rtc 48070000.i2c:twl@48:rtc: rtc core: registered 48070000.i2c:twl@48 as rtc0
[    1.684326] i2c /dev entries driver
[    1.692596] Driver for 1-wire Dallas network protocol.
[    1.704498] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[    1.714324] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer cd
[    1.714447] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup
[    1.714508] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/ocp@68000000/mmc@480b4000[0]'
[    1.714630] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/ocp@68000000/mmc@480b4000[0]'
[    1.714721] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup
[    1.714935] omap_hsmmc 480b4000.mmc: lookup for GPIO cd failed
[    1.715026] omap_hsmmc 480b4000.mmc: GPIO lookup for consumer wp
[    1.715118] omap_hsmmc 480b4000.mmc: using device tree for GPIO lookup
[    1.715179] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp@68000000/mmc@480b4000[0]'
[    1.715270] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp@68000000/mmc@480b4000[0]'
[    1.715393] omap_hsmmc 480b4000.mmc: using lookup tables for GPIO lookup
[    1.715454] omap_hsmmc 480b4000.mmc: lookup for GPIO wp failed
[    1.718139] omap_hsmmc 480b4000.mmc: RX DMA channel request failed
[    1.740539] FPGA DOWNLOAD --->
[    1.740600] FPGA image file name: xlinx_fpga_firmware.bit
[    1.742218] GPIO INIT FAIL!!
[    1.746093] Initializing XFRM netlink socket
[    1.746704] NET: Registered protocol family 17
[    1.746948] NET: Registered protocol family 15
[    1.747558] Key type dns_resolver registered
[    1.748168] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu_iva
[    1.748260] omap2_set_init_voltage: unable to set vdd_mpu_iva
[    1.748352] omap2_set_init_voltage: unable to find boot up OPP for vdd_core
[    1.748413] omap2_set_init_voltage: unable to set vdd_core
[    1.868743] twl_rtc 48070000.i2c:twl@48:rtc: setting system clock to 2016-12-16 11:47:32 UTC (1481888852)
[    1.872192] usb0: eth_open
[    2.162048] g_ether gadget: high-speed config #1: CDC Ethernet (ECM)
[    2.162322] g_ether gadget: init ecm
[    2.162384] g_ether gadget: notify connect false
[    2.163452] g_ether gadget: activate ecm
[    2.163848] usb0: qlen 10
[    2.163940] g_ether gadget: ecm_open
[    2.164062] usb0: eth_start
[    2.164886] g_ether gadget: packet filter 0c
[    2.164947] g_ether gadget: ecm req21.43 v000c i0000 l0
[    2.196624] IP-Config: Guessing netmask 255.255.255.0
[    2.196716] IP-Config: Complete:
[    2.196777]      device=usb0, hwaddr=c2:16:47:78:17:05, ipaddr=192.168.1.130, mask=255.255.255.0, gw=192.168.1.129
[    2.196868]      host=192.168.1.130, domain=, nis-domain=(none)
[    2.196929]      bootserver=255.255.255.255, rootserver=192.168.1.129, rootpath=
[    2.198852] VEMMC: disabling
[    2.198913] VWLAN: disabling
[    2.199554] vaux1: disabling
[    2.201324] vmmc1: disabling
[    2.201934] vmmc2: disabling
[    2.202514] vpll2: disabling
[    2.205230] Waiting 5 sec before mounting root device...
[    2.264862] g_ether gadget: packet filter 0e
[    2.264953] g_ether gadget: ecm req21.43 v000e i0000 l0
[    2.265136] g_ether gadget: packet filter 0e
[    2.265197] g_ether gadget: ecm req21.43 v000e i0000 l0
[    7.308624] VFS: Mounted root (nfs filesystem) on device 0:14.
[    7.311492] devtmpfs: mounted
[    7.314849] Freeing unused kernel memory: 1024K (c0700000 - c0800000)
[   10.908508] random: crng init done
[   90.905456] systemd-logind[2167]: Watching system buttons on /dev/input/event0 (twl4030_pwrbutton)
[   90.906097] systemd-logind[2167]: New seat seat0.
[   90.994140] systemd-logind[2167]: Failed to start user service, ignoring: Unknown unit: user@1000.service
[   91.020202] systemd-logind[2167]: New session c1 of user sailus.
[   92.451293] systemd-logind[2167]: New session c2 of user sailus.
[   95.002410] systemd-logind[2167]: Failed to start user service, ignoring: Unknown unit: user@0.service
[   95.014801] systemd-logind[2167]: New session c3 of user root.
[   96.710968] media: Linux media interface: v0.10
[   97.472167] Linux video capture interface: v2.00
[   98.979431] omap3isp 480bc000.isp: parsing endpoint /ocp@68000000/isp@480bc000/ports/port@2/endpoint, interface 2
[   98.979522] omap3isp 480bc000.isp: clock lane polarity 1, pos 2
[   98.979583] omap3isp 480bc000.isp: data lane 0 polarity 1, pos 1
[   98.979644] omap3isp 480bc000.isp: data lane 1 polarity 1, pos 3
[   98.981414] omap3isp 480bc000.isp: Revision 15.0 found
[   98.984558] iommu: Adding device 480bc000.isp to group 0
[   98.985809] omap-iommu 480bd400.mmu: 480bd400.mmu: version 1.1
[   98.996704] omap3isp 480bc000.isp: hist: DMA channel request failed, using PIO
[   98.996856] omap3isp 480bc000.isp: Media device initialized
[   98.996917] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP CCP2 was not initialized!
[   98.997558] omap3isp 480bc000.isp: media_gobj_create id 1: entity 'OMAP3 ISP CCP2'
[   98.997680] omap3isp 480bc000.isp: media_gobj_create id 2: sink pad 'OMAP3 ISP CCP2':0
[   98.997772] omap3isp 480bc000.isp: media_gobj_create id 3: source pad 'OMAP3 ISP CCP2':1
[   99.017211] omap3isp 480bc000.isp: media_gobj_create id 4: entity 'OMAP3 ISP CCP2 input'
[   99.017364] omap3isp 480bc000.isp: media_gobj_create id 5: source pad 'OMAP3 ISP CCP2 input':0
[   99.017486] omap3isp 480bc000.isp: media_gobj_create id 6: intf_devnode v4l-video - major: 81, minor: 0
[   99.017578] omap3isp 480bc000.isp: media_gobj_create id 7: interface link id 6 ==> id 4
[   99.017669] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP CSI2a was not initialized!
[   99.017822] omap3isp 480bc000.isp: media_gobj_create id 8: entity 'OMAP3 ISP CSI2a'
[   99.017913] omap3isp 480bc000.isp: media_gobj_create id 9: sink pad 'OMAP3 ISP CSI2a':0
[   99.018005] omap3isp 480bc000.isp: media_gobj_create id 10: source pad 'OMAP3 ISP CSI2a':1
[   99.035339] omap3isp 480bc000.isp: media_gobj_create id 11: entity 'OMAP3 ISP CSI2a output'
[   99.035461] omap3isp 480bc000.isp: media_gobj_create id 12: sink pad 'OMAP3 ISP CSI2a output':0
[   99.035583] omap3isp 480bc000.isp: media_gobj_create id 13: intf_devnode v4l-video - major: 81, minor: 1
[   99.035705] omap3isp 480bc000.isp: media_gobj_create id 14: interface link id 13 ==> id 11
[   99.035797] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP CCDC was not initialized!
[   99.035919] omap3isp 480bc000.isp: media_gobj_create id 15: entity 'OMAP3 ISP CCDC'
[   99.036010] omap3isp 480bc000.isp: media_gobj_create id 16: sink pad 'OMAP3 ISP CCDC':0
[   99.036102] omap3isp 480bc000.isp: media_gobj_create id 17: source pad 'OMAP3 ISP CCDC':1
[   99.046569] omap3isp 480bc000.isp: media_gobj_create id 18: source pad 'OMAP3 ISP CCDC':2
[   99.050018] omap3isp 480bc000.isp: media_gobj_create id 19: entity 'OMAP3 ISP CCDC output'
[   99.050140] omap3isp 480bc000.isp: media_gobj_create id 20: sink pad 'OMAP3 ISP CCDC output':0
[   99.050262] omap3isp 480bc000.isp: media_gobj_create id 21: intf_devnode v4l-video - major: 81, minor: 2
[   99.050354] omap3isp 480bc000.isp: media_gobj_create id 22: interface link id 21 ==> id 19
[   99.050476] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP preview was not initialized!
[   99.050598] omap3isp 480bc000.isp: media_gobj_create id 23: entity 'OMAP3 ISP preview'
[   99.050689] omap3isp 480bc000.isp: media_gobj_create id 24: sink pad 'OMAP3 ISP preview':0
[   99.050781] omap3isp 480bc000.isp: media_gobj_create id 25: source pad 'OMAP3 ISP preview':1
[   99.073944] omap3isp 480bc000.isp: media_gobj_create id 26: entity 'OMAP3 ISP preview input'
[   99.074066] omap3isp 480bc000.isp: media_gobj_create id 27: source pad 'OMAP3 ISP preview input':0
[   99.074188] omap3isp 480bc000.isp: media_gobj_create id 28: intf_devnode v4l-video - major: 81, minor: 3
[   99.074310] omap3isp 480bc000.isp: media_gobj_create id 29: interface link id 28 ==> id 26
[   99.075836] omap3isp 480bc000.isp: media_gobj_create id 30: entity 'OMAP3 ISP preview output'
[   99.075958] omap3isp 480bc000.isp: media_gobj_create id 31: sink pad 'OMAP3 ISP preview output':0
[   99.076080] omap3isp 480bc000.isp: media_gobj_create id 32: intf_devnode v4l-video - major: 81, minor: 4
[   99.076171] omap3isp 480bc000.isp: media_gobj_create id 33: interface link id 32 ==> id 30
[   99.077819] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP resizer was not initialized!
[   99.077972] omap3isp 480bc000.isp: media_gobj_create id 34: entity 'OMAP3 ISP resizer'
[   99.078063] omap3isp 480bc000.isp: media_gobj_create id 35: sink pad 'OMAP3 ISP resizer':0
[   99.078155] omap3isp 480bc000.isp: media_gobj_create id 36: source pad 'OMAP3 ISP resizer':1
[   99.095001] omap3isp 480bc000.isp: media_gobj_create id 37: entity 'OMAP3 ISP resizer input'
[   99.095153] omap3isp 480bc000.isp: media_gobj_create id 38: source pad 'OMAP3 ISP resizer input':0
[   99.095245] omap3isp 480bc000.isp: media_gobj_create id 39: intf_devnode v4l-video - major: 81, minor: 5
[   99.095367] omap3isp 480bc000.isp: media_gobj_create id 40: interface link id 39 ==> id 37
[   99.117553] omap3isp 480bc000.isp: media_gobj_create id 41: entity 'OMAP3 ISP resizer output'
[   99.117706] omap3isp 480bc000.isp: media_gobj_create id 42: sink pad 'OMAP3 ISP resizer output':0
[   99.117797] omap3isp 480bc000.isp: media_gobj_create id 43: intf_devnode v4l-video - major: 81, minor: 6
[   99.117919] omap3isp 480bc000.isp: media_gobj_create id 44: interface link id 43 ==> id 41
[   99.118011] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP AEWB was not initialized!
[   99.118164] omap3isp 480bc000.isp: media_gobj_create id 45: entity 'OMAP3 ISP AEWB'
[   99.118255] omap3isp 480bc000.isp: media_gobj_create id 46: sink pad 'OMAP3 ISP AEWB':0
[   99.118347] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP AF was not initialized!
[   99.118469] omap3isp 480bc000.isp: media_gobj_create id 47: entity 'OMAP3 ISP AF'
[   99.118560] omap3isp 480bc000.isp: media_gobj_create id 48: sink pad 'OMAP3 ISP AF':0
[   99.118682] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP histogram was not initialized!
[   99.118804] omap3isp 480bc000.isp: media_gobj_create id 49: entity 'OMAP3 ISP histogram'
[   99.118896] omap3isp 480bc000.isp: media_gobj_create id 50: sink pad 'OMAP3 ISP histogram':0
[   99.119018] omap3isp 480bc000.isp: media_gobj_create id 51: data link id 10 ==> id 12
[   99.119110] omap3isp 480bc000.isp: media_gobj_create id 52: data link id 10 ==> id 12
[   99.119201] omap3isp 480bc000.isp: media_gobj_create id 53: data link id 5 ==> id 2
[   99.119293] omap3isp 480bc000.isp: media_gobj_create id 54: data link id 5 ==> id 2
[   99.119384] omap3isp 480bc000.isp: media_gobj_create id 55: data link id 17 ==> id 20
[   99.119506] omap3isp 480bc000.isp: media_gobj_create id 56: data link id 17 ==> id 20
[   99.119598] omap3isp 480bc000.isp: media_gobj_create id 57: data link id 27 ==> id 24
[   99.119689] omap3isp 480bc000.isp: media_gobj_create id 58: data link id 27 ==> id 24
[   99.119781] omap3isp 480bc000.isp: media_gobj_create id 59: data link id 25 ==> id 31
[   99.119903] omap3isp 480bc000.isp: media_gobj_create id 60: data link id 25 ==> id 31
[   99.119995] omap3isp 480bc000.isp: media_gobj_create id 61: data link id 38 ==> id 35
[   99.120086] omap3isp 480bc000.isp: media_gobj_create id 62: data link id 38 ==> id 35
[   99.120178] omap3isp 480bc000.isp: media_gobj_create id 63: data link id 36 ==> id 42
[   99.120300] omap3isp 480bc000.isp: media_gobj_create id 64: data link id 36 ==> id 42
[   99.120391] omap3isp 480bc000.isp: media_gobj_create id 65: data link id 10 ==> id 16
[   99.120483] omap3isp 480bc000.isp: media_gobj_create id 66: data link id 10 ==> id 16
[   99.120574] omap3isp 480bc000.isp: media_gobj_create id 67: data link id 3 ==> id 16
[   99.120666] omap3isp 480bc000.isp: media_gobj_create id 68: data link id 3 ==> id 16
[   99.120758] omap3isp 480bc000.isp: media_gobj_create id 69: data link id 18 ==> id 24
[   99.120880] omap3isp 480bc000.isp: media_gobj_create id 70: data link id 18 ==> id 24
[   99.120971] omap3isp 480bc000.isp: media_gobj_create id 71: data link id 17 ==> id 35
[   99.121063] omap3isp 480bc000.isp: media_gobj_create id 72: data link id 17 ==> id 35
[   99.121154] omap3isp 480bc000.isp: media_gobj_create id 73: data link id 25 ==> id 35
[   99.121246] omap3isp 480bc000.isp: media_gobj_create id 74: data link id 25 ==> id 35
[   99.121368] omap3isp 480bc000.isp: media_gobj_create id 75: data link id 18 ==> id 46
[   99.121459] omap3isp 480bc000.isp: media_gobj_create id 76: data link id 18 ==> id 46
[   99.121551] omap3isp 480bc000.isp: media_gobj_create id 77: data link id 18 ==> id 48
[   99.121643] omap3isp 480bc000.isp: media_gobj_create id 78: data link id 18 ==> id 48
[   99.121765] omap3isp 480bc000.isp: media_gobj_create id 79: data link id 18 ==> id 50
[   99.121856] omap3isp 480bc000.isp: media_gobj_create id 80: data link id 18 ==> id 50
[  100.080444] smiapp 1-0010: lanes 2
[  100.080535] smiapp 1-0010: nvm 1024, clk 9600000, csi 2
[  100.080627] smiapp 1-0010: freq 0: 199200000
[  100.080688] smiapp 1-0010: freq 1: 210000000
[  100.080749] smiapp 1-0010: freq 2: 499200000
[  100.082061] omap3isp 480bc000.isp: isp_xclk_set_rate: cam_xclka set to 9600000 Hz (div 18)
[  100.082183] smiapp 1-0010: GPIO lookup for consumer xshutdown
[  100.082275] smiapp 1-0010: using device tree for GPIO lookup
[  100.082336] of_get_named_gpiod_flags: can't parse 'xshutdown-gpios' property of node '/ocp@68000000/i2c@48072000/camera@10[0]'
[  100.082458] of_get_named_gpiod_flags: can't parse 'xshutdown-gpio' property of node '/ocp@68000000/i2c@48072000/camera@10[0]'
[  100.082550] smiapp 1-0010: using lookup tables for GPIO lookup
[  100.082641] smiapp 1-0010: lookup for GPIO xshutdown failed
[  100.133239] smiapp 1-0010: module 0x0c-0x560f
[  100.133361] smiapp 1-0010: module revision 0x03-0x04 date 11-05-31
[  100.133422] smiapp 1-0010: sensor 0x0c-0x0905
[  100.133483] smiapp 1-0010: sensor revision 0x02 firmware version 0x00
[  100.133544] smiapp 1-0010: smia version 10 smiapp version 08
[  100.133636] smiapp 1-0010: the sensor is called jt8ew9, ident 0c560f03
[  100.134094] smiapp 1-0010: 0x00020080 "analogue_gain_capability" = 0, 0x0
[  100.134643] smiapp 1-0010: 0x00020084 "analogue_gain_code_min" = 68, 0x44
[  100.135162] smiapp 1-0010: 0x00020086 "analogue_gain_code_max" = 544, 0x220
[  100.135681] smiapp 1-0010: 0x00010802 "ths_zero_min" = 104, 0x68
[  100.136169] smiapp 1-0010: 0x00010804 "tclk_trail_min" = 64, 0x40
[  100.138183] smiapp 1-0010: 0x00021000 "integration_time_capability" = 0, 0x0
[  100.138702] smiapp 1-0010: 0x00021004 "coarse_integration_time_min" = 0, 0x0
[  100.139190] smiapp 1-0010: 0x00021006 "coarse_integration_time_max_margin" = 8, 0x8
[  100.139739] smiapp 1-0010: 0x00021008 "fine_integration_time_min" = 0, 0x0
[  100.140228] smiapp 1-0010: 0x0002100a "fine_integration_time_max_margin" = 0, 0x0
[  100.140747] smiapp 1-0010: 0x00021080 "digital_gain_capability" = 1, 0x1
[  100.141265] smiapp 1-0010: 0x00021084 "digital_gain_min" = 0, 0x0
[  100.141754] smiapp 1-0010: 0x00021086 "digital_gain_max" = 1023, 0x3ff
[  100.142272] smiapp 1-0010: 0x01041100 "min_ext_clk_freq_hz" = 6000000, 0x5b8d80
[  100.142852] smiapp 1-0010: 0x01041104 "max_ext_clk_freq_hz" = 27000000, 0x19bfcc0
[  100.143371] smiapp 1-0010: 0x00021108 "min_pre_pll_clk_div" = 1, 0x1
[  100.143859] smiapp 1-0010: 0x0002110a "max_pre_pll_clk_div" = 2, 0x2
[  100.144378] smiapp 1-0010: 0x0104110c "min_pll_ip_freq_hz" = 5000000, 0x4c4b40
[  100.144927] smiapp 1-0010: 0x01041110 "max_pll_ip_freq_hz" = 27000000, 0x19bfcc0
[  100.145446] smiapp 1-0010: 0x00021114 "min_pll_multiplier" = 36, 0x24
[  100.145965] smiapp 1-0010: 0x00021116 "max_pll_multiplier" = 400, 0x190
[  100.148284] smiapp 1-0010: 0x01041118 "min_pll_op_freq_hz" = 1000000000, 0x3b9aca00
[  100.148864] smiapp 1-0010: 0x0104111c "max_pll_op_freq_hz" = 2000000000, 0x77359400
[  100.149414] smiapp 1-0010: 0x00021120 "min_vt_sys_clk_div" = 1, 0x1
[  100.149902] smiapp 1-0010: 0x00021122 "max_vt_sys_clk_div" = 12, 0xc
[  100.150451] smiapp 1-0010: 0x01041124 "min_vt_sys_clk_freq_hz" = 83329994, 0x4f783ca
[  100.151000] smiapp 1-0010: 0x01041128 "max_vt_sys_clk_freq_hz" = 2000000000, 0x77359400
[  100.151550] smiapp 1-0010: 0x0104112c "min_vt_pix_clk_freq_hz" = 40000000, 0x2625a00
[  100.152130] smiapp 1-0010: 0x01041130 "max_vt_pix_clk_freq_hz" = 262000000, 0xf9dcd80
[  100.152648] smiapp 1-0010: 0x00021134 "min_vt_pix_clk_div" = 2, 0x2
[  100.153137] smiapp 1-0010: 0x00021136 "max_vt_pix_clk_div" = 12, 0xc
[  100.153625] smiapp 1-0010: 0x00021140 "min_frame_length_lines" = 192, 0xc0
[  100.154113] smiapp 1-0010: 0x00021142 "max_frame_length_lines" = 65535, 0xffff
[  100.154632] smiapp 1-0010: 0x00021144 "min_line_length_pck" = 2008, 0x7d8
[  100.155151] smiapp 1-0010: 0x00021146 "max_line_length_pck" = 16382, 0x3ffe
[  100.155639] smiapp 1-0010: 0x00021148 "min_line_blanking_pck" = 200, 0xc8
[  100.156127] smiapp 1-0010: 0x0002114a "min_frame_blanking_lines" = 40, 0x28
[  100.158386] smiapp 1-0010: 0x0001114c "min_line_length_pck_step_size" = 2, 0x2
[  100.158935] smiapp 1-0010: 0x00021160 "min_op_sys_clk_div" = 1, 0x1
[  100.159454] smiapp 1-0010: 0x00021162 "max_op_sys_clk_div" = 12, 0xc
[  100.159973] smiapp 1-0010: 0x01041164 "min_op_sys_clk_freq_hz" = 400000000, 0x17d78400
[  100.160552] smiapp 1-0010: 0x01041168 "max_op_sys_clk_freq_hz" = 2000000000, 0x77359400
[  100.161071] smiapp 1-0010: 0x0002116c "min_op_pix_clk_div" = 6, 0x6
[  100.161590] smiapp 1-0010: 0x0002116e "max_op_pix_clk_div" = 10, 0xa
[  100.162109] smiapp 1-0010: 0x01041170 "min_op_pix_clk_freq_hz" = 50000000, 0x2faf080
[  100.162658] smiapp 1-0010: 0x01041174 "max_op_pix_clk_freq_hz" = 250000000, 0xee6b280
[  100.163177] smiapp 1-0010: 0x00021180 "x_addr_min" = 0, 0x0
[  100.163696] smiapp 1-0010: 0x00021182 "y_addr_min" = 0, 0x0
[  100.164184] smiapp 1-0010: 0x00021184 "x_addr_max" = 3599, 0xe0f
[  100.164672] smiapp 1-0010: 0x00021186 "y_addr_max" = 2463, 0x99f
[  100.165161] smiapp 1-0010: 0x00021188 "min_x_output_size" = 184, 0xb8
[  100.165649] smiapp 1-0010: 0x0002118a "min_y_output_size" = 152, 0x98
[  100.166168] smiapp 1-0010: 0x0002118c "max_x_output_size" = 3576, 0xdf8
[  100.168182] smiapp 1-0010: 0x0002118e "max_y_output_size" = 2464, 0x9a0
[  100.168701] smiapp 1-0010: 0x000211c0 "min_even_inc" = 1, 0x1
[  100.169219] smiapp 1-0010: 0x000211c2 "max_even_inc" = 1, 0x1
[  100.169708] smiapp 1-0010: 0x000211c4 "min_odd_inc" = 1, 0x1
[  100.170196] smiapp 1-0010: 0x000211c6 "max_odd_inc" = 1, 0x1
[  100.170684] smiapp 1-0010: 0x00021200 "scaling_capability" = 2, 0x2
[  100.171173] smiapp 1-0010: 0x00021204 "scaler_m_min" = 16, 0x10
[  100.171691] smiapp 1-0010: 0x00021206 "scaler_m_max" = 255, 0xff
[  100.172180] smiapp 1-0010: 0x00021208 "scaler_n_min" = 16, 0x10
[  100.172668] smiapp 1-0010: 0x0002120a "scaler_n_max" = 16, 0x10
[  100.173156] smiapp 1-0010: 0x0002120c "spatial_sampling_capability" = 3, 0x3
[  100.173675] smiapp 1-0010: 0x0001120e "digital_crop_capability" = 1, 0x1
[  100.174163] smiapp 1-0010: 0x00021300 "compression_capability" = 1, 0x1
[  100.174682] smiapp 1-0010: 0x00011502 "fifo_support_capability" = 1, 0x1
[  100.175170] smiapp 1-0010: 0x00011600 "dphy_ctrl_capability" = 30, 0x1e
[  100.175659] smiapp 1-0010: 0x00011601 "csi_lane_mode_capability" = 3, 0x3
[  100.176177] smiapp 1-0010: 0x00011602 "csi_signalling_mode_capability" = 7, 0x7
[  100.178192] smiapp 1-0010: 0x00011603 "fast_standby_capability" = 1, 0x1
[  100.178741] smiapp 1-0010: 0x00011604 "cci_address_control_capability" = 1, 0x1
[  100.179290] smiapp 1-0010: 0x00041608 "max_per_lane_bitrate_1_lane_mode_mbps" = 65536000, 0x3e80000
[  100.179870] smiapp 1-0010: 0x0004160c "max_per_lane_bitrate_2_lane_mode_mbps" = 65536000, 0x3e80000
[  100.180419] smiapp 1-0010: 0x00041610 "max_per_lane_bitrate_3_lane_mode_mbps" = 0, 0x0
[  100.180969] smiapp 1-0010: 0x00041614 "max_per_lane_bitrate_4_lane_mode_mbps" = 0, 0x0
[  100.181518] smiapp 1-0010: 0x00011618 "temp_sensor_capability" = 0, 0x0
[  100.182006] smiapp 1-0010: 0x00021700 "min_frame_length_lines_bin" = 192, 0xc0
[  100.182525] smiapp 1-0010: 0x00021702 "max_frame_length_lines_bin" = 65535, 0xffff
[  100.183044] smiapp 1-0010: 0x00021704 "min_line_length_pck_bin" = 1104, 0x450
[  100.183563] smiapp 1-0010: 0x00021706 "max_line_length_pck_bin" = 16382, 0x3ffe
[  100.184082] smiapp 1-0010: 0x00021708 "min_line_blanking_pck_bin" = 200, 0xc8
[  100.184570] smiapp 1-0010: 0x0002170a "fine_integration_time_min_bin" = 0, 0x0
[  100.185089] smiapp 1-0010: 0x0002170c "fine_integration_time_max_margin_bin" = 0, 0x0
[  100.185638] smiapp 1-0010: 0x00011710 "binning_capability" = 1, 0x1
[  100.186126] smiapp 1-0010: 0x00011711 "binning_weighting_capability" = 5, 0x5
[  100.188018] smiapp 1-0010: 0x00011800 "data_transfer_if_capability" = 13, 0xd
[  100.188568] smiapp 1-0010: 0x00011900 "shading_correction_capability" = 0, 0x0
[  100.189086] smiapp 1-0010: 0x00011901 "green_imbalance_capability" = 0, 0x0
[  100.189575] smiapp 1-0010: 0x00011902 "black_level_capability" = 0, 0x0
[  100.190093] smiapp 1-0010: 0x00011903 "module_specific_correction_capability" = 0, 0x0
[  100.190612] smiapp 1-0010: 0x00021904 "defect_correction_capability" = 865, 0x361
[  100.191131] smiapp 1-0010: 0x00021906 "defect_correction_capability_2" = 0, 0x0
[  100.191650] smiapp 1-0010: 0x00011980 "edof_capability" = 0, 0x0
[  100.192138] smiapp 1-0010: 0x00011987 "colour_feedback_capability" = 0, 0x0
[  100.192657] smiapp 1-0010: 0x000119c0 "estimation_mode_capability" = 0, 0x0
[  100.193145] smiapp 1-0010: 0x000119c1 "estimation_zone_capability" = 0, 0x0
[  100.193634] smiapp 1-0010: 0x00021a00 "capability_trdy_min" = 0, 0x0
[  100.194152] smiapp 1-0010: 0x00011a02 "flash_mode_capability" = 3, 0x3
[  100.194641] smiapp 1-0010: 0x00011b04 "actuator_capability" = 4, 0x4
[  100.195129] smiapp 1-0010: 0x00011c00 "bracketing_lut_capability_1" = 3, 0x3
[  100.195648] smiapp 1-0010: 0x00011c01 "bracketing_lut_capability_2" = 0, 0x0
[  100.196136] smiapp 1-0010: 0x00020088 "analogue_gain_code_step" = 1, 0x1
[  100.198455] smiapp 1-0010: format_model_type 2 byte
[  100.199005] smiapp 1-0010: 0x00020042 visible pixels: 3576 columns (pixelcode 5)
[  100.199523] smiapp 1-0010: 0x00020044 embedded pixels: 2 rows (pixelcode 1)
[  100.200012] smiapp 1-0010: 0x00020046 visible pixels: 2464 rows (pixelcode 5)
[  100.200103] smiapp 1-0010: embedded data from lines 0 to 2
[  100.200164] smiapp 1-0010: image data starts at line 2
[  100.200225] smiapp 1-0010: quirk: 0x00020084 "analogue_gain_code_min" = 59, 0x3b
[  100.200317] smiapp 1-0010: quirk: 0x00020086 "analogue_gain_code_max" = 6000, 0x1770
[  100.201263] smiapp 1-0010: binning 2x1
[  100.201721] smiapp 1-0010: binning 3x1
[  100.202209] smiapp 1-0010: binning 4x1
[  100.202697] smiapp 1-0010: binning 5x1
[  100.203186] smiapp 1-0010: binning 6x1
[  100.203674] smiapp 1-0010: binning 7x1
[  100.204132] smiapp 1-0010: binning 8x1
[  100.204620] smiapp 1-0010: binning 1x2
[  100.205108] smiapp 1-0010: binning 2x2
[  100.205596] smiapp 1-0010: binning 3x2
[  100.206085] smiapp 1-0010: binning 4x2
[  100.210601] smiapp 1-0010: binning 5x2
[  100.211029] smiapp 1-0010: binning 6x2
[  100.211547] smiapp 1-0010: binning 7x2
[  100.212036] smiapp 1-0010: binning 8x2
[  100.212310] smiapp 1-0010: profile 2
[  100.213531] smiapp 1-0010: data_format_model_type 1
[  100.214080] smiapp 1-0010: pixel order 0 (GRBG)
[  100.214569] smiapp 1-0010: 0: bpp 8, compressed 8
[  100.214660] smiapp 1-0010: jolly good! 20
[  100.215148] smiapp 1-0010: 1: bpp 10, compressed 10
[  100.215209] smiapp 1-0010: jolly good! 12
[  100.215698] smiapp 1-0010: 2: bpp 10, compressed 8
[  100.215759] smiapp 1-0010: jolly good! 16
[  100.217773] smiapp 1-0010: 3: bpp 10, compressed 6
[  100.218353] smiapp 1-0010: 4: bpp 0, compressed 0
[  100.218872] smiapp 1-0010: 5: bpp 0, compressed 0
[  100.219360] smiapp 1-0010: 6: bpp 0, compressed 0
[  100.219848] smiapp 1-0010: 7: bpp 0, compressed 0
[  100.219970] smiapp 1-0010: link freq 199200000 Hz, bpp 10 ok
[  100.220062] smiapp 1-0010: link freq 210000000 Hz, bpp 10 ok
[  100.220123] smiapp 1-0010: link freq 499200000 Hz, bpp 10 ok
[  100.220184] smiapp 1-0010: link freq 199200000 Hz, bpp 8 ok
[  100.220275] smiapp 1-0010: link freq 210000000 Hz, bpp 8 ok
[  100.220336] smiapp 1-0010: link freq 499200000 Hz, bpp 8 ok
[  100.220397] smiapp 1-0010: link freq 199200000 Hz, bpp 8 ok
[  100.220489] smiapp 1-0010: link freq 210000000 Hz, bpp 8 ok
[  100.220550] smiapp 1-0010: link freq 499200000 Hz, bpp 8 ok
[  100.220611] smiapp 1-0010: flip 0
[  100.220672] smiapp 1-0010: new pixel order GRBG
[  100.221679] smiapp 1-0010: 0x00021700 "min_frame_length_lines_bin" = 192, 0xc0
[  100.222229] smiapp 1-0010: 0x00021702 "max_frame_length_lines_bin" = 65535, 0xffff
[  100.222747] smiapp 1-0010: 0x00021704 "min_line_length_pck_bin" = 1104, 0x450
[  100.223266] smiapp 1-0010: 0x00021706 "max_line_length_pck_bin" = 16382, 0x3ffe
[  100.223785] smiapp 1-0010: 0x00021708 "min_line_blanking_pck_bin" = 200, 0xc8
[  100.224273] smiapp 1-0010: 0x0002170a "fine_integration_time_min_bin" = 0, 0x0
[  100.224822] smiapp 1-0010: 0x0002170c "fine_integration_time_max_margin_bin" = 0, 0x0
[  100.225555] smiapp 1-0010: vblank		40
[  100.225616] smiapp 1-0010: hblank		200
[  100.225677] smiapp 1-0010: real timeperframe	100/837
[  100.225769] omap3isp 480bc000.isp: Entity type for entity jt8ew9 scaler 1-0010 was not initialized!
[  100.226074] omap3isp 480bc000.isp: media_gobj_create id 81: entity 'jt8ew9 scaler 1-0010'
[  100.226165] omap3isp 480bc000.isp: media_gobj_create id 82: sink pad 'jt8ew9 scaler 1-0010':0
[  100.228637] omap3isp 480bc000.isp: media_gobj_create id 83: source pad 'jt8ew9 scaler 1-0010':1
[  100.228729] omap3isp 480bc000.isp: Entity type for entity jt8ew9 binner 1-0010 was not initialized!
[  100.228881] omap3isp 480bc000.isp: media_gobj_create id 84: entity 'jt8ew9 binner 1-0010'
[  100.228973] omap3isp 480bc000.isp: media_gobj_create id 85: sink pad 'jt8ew9 binner 1-0010':0
[  100.229095] omap3isp 480bc000.isp: media_gobj_create id 86: source pad 'jt8ew9 binner 1-0010':1
[  100.229278] omap3isp 480bc000.isp: media_gobj_create id 87: data link id 86 ==> id 82
[  100.229370] omap3isp 480bc000.isp: media_gobj_create id 88: data link id 86 ==> id 82
[  100.229522] omap3isp 480bc000.isp: media_gobj_create id 89: entity 'jt8ew9 pixel_array 1-0010'
[  100.229614] omap3isp 480bc000.isp: media_gobj_create id 90: source pad 'jt8ew9 pixel_array 1-0010':0
[  100.229705] omap3isp 480bc000.isp: media_gobj_create id 91: data link id 90 ==> id 85
[  100.229827] omap3isp 480bc000.isp: media_gobj_create id 92: data link id 90 ==> id 85
[  100.229919] omap3isp 480bc000.isp: media_gobj_create id 93: data link id 83 ==> id 9
[  100.230102] omap3isp 480bc000.isp: media_gobj_create id 94: data link id 83 ==> id 9
[  100.240844] omap3isp 480bc000.isp: media_gobj_create id 95: intf_devnode v4l-subdev - major: 81, minor: 7
[  100.241027] omap3isp 480bc000.isp: media_gobj_create id 96: interface link id 95 ==> id 1
[  100.242675] omap3isp 480bc000.isp: media_gobj_create id 97: intf_devnode v4l-subdev - major: 81, minor: 8
[  100.242797] omap3isp 480bc000.isp: media_gobj_create id 98: interface link id 97 ==> id 8
[  100.256774] omap3isp 480bc000.isp: media_gobj_create id 99: intf_devnode v4l-subdev - major: 81, minor: 9
[  100.256927] omap3isp 480bc000.isp: media_gobj_create id 100: interface link id 99 ==> id 15
[  100.267517] omap3isp 480bc000.isp: media_gobj_create id 101: intf_devnode v4l-subdev - major: 81, minor: 10
[  100.267669] omap3isp 480bc000.isp: media_gobj_create id 102: interface link id 101 ==> id 23
[  100.277679] omap3isp 480bc000.isp: media_gobj_create id 103: intf_devnode v4l-subdev - major: 81, minor: 11
[  100.277832] omap3isp 480bc000.isp: media_gobj_create id 104: interface link id 103 ==> id 34
[  100.279418] omap3isp 480bc000.isp: media_gobj_create id 105: intf_devnode v4l-subdev - major: 81, minor: 12
[  100.279541] omap3isp 480bc000.isp: media_gobj_create id 106: interface link id 105 ==> id 45
[  100.281005] omap3isp 480bc000.isp: media_gobj_create id 107: intf_devnode v4l-subdev - major: 81, minor: 13
[  100.281127] omap3isp 480bc000.isp: media_gobj_create id 108: interface link id 107 ==> id 47
[  100.287719] omap3isp 480bc000.isp: media_gobj_create id 109: intf_devnode v4l-subdev - major: 81, minor: 14
[  100.287841] omap3isp 480bc000.isp: media_gobj_create id 110: interface link id 109 ==> id 49
[  100.293731] omap3isp 480bc000.isp: media_gobj_create id 111: intf_devnode v4l-subdev - major: 81, minor: 15
[  100.293884] omap3isp 480bc000.isp: media_gobj_create id 112: interface link id 111 ==> id 84
[  100.306762] omap3isp 480bc000.isp: media_gobj_create id 113: intf_devnode v4l-subdev - major: 81, minor: 16
[  100.306915] omap3isp 480bc000.isp: media_gobj_create id 114: interface link id 113 ==> id 89
[  100.317626] omap3isp 480bc000.isp: media_gobj_create id 115: intf_devnode v4l-subdev - major: 81, minor: 17
[  100.317779] omap3isp 480bc000.isp: media_gobj_create id 116: interface link id 115 ==> id 81
[  100.322357] omap3isp 480bc000.isp: Media device registered
[  104.372009] omap3isp 480bc000.isp: media_gobj_destroy id 112: interface link id 111 ==> id 84
[  104.372161] omap3isp 480bc000.isp: media_gobj_destroy id 88: data link id 86 ==> id 82
[  104.372283] omap3isp 480bc000.isp: media_gobj_destroy id 87: data link id 86 ==> id 82
[  104.372375] omap3isp 480bc000.isp: media_gobj_destroy id 91: data link id 90 ==> id 85
[  104.372467] omap3isp 480bc000.isp: media_gobj_destroy id 92: data link id 90 ==> id 85
[  104.372589] omap3isp 480bc000.isp: media_gobj_destroy id 85: sink pad 'jt8ew9 binner 1-0010':0
[  104.372680] omap3isp 480bc000.isp: media_gobj_destroy id 86: source pad 'jt8ew9 binner 1-0010':1
[  104.372772] omap3isp 480bc000.isp: media_gobj_destroy id 84: entity 'jt8ew9 binner 1-0010'
[  104.387878] omap3isp 480bc000.isp: media_gobj_destroy id 111: intf_devnode v4l-subdev - major: 81, minor: 15
[  104.388061] omap3isp 480bc000.isp: media_gobj_destroy id 114: interface link id 113 ==> id 89
[  104.388183] omap3isp 480bc000.isp: media_gobj_destroy id 90: source pad 'jt8ew9 pixel_array 1-0010':0
[  104.388275] omap3isp 480bc000.isp: media_gobj_destroy id 89: entity 'jt8ew9 pixel_array 1-0010'
[  104.392883] omap3isp 480bc000.isp: media_gobj_destroy id 113: intf_devnode v4l-subdev - major: 81, minor: 16
[  104.393066] omap3isp 480bc000.isp: media_gobj_destroy id 116: interface link id 115 ==> id 81
[  104.393188] omap3isp 480bc000.isp: media_gobj_destroy id 94: data link id 83 ==> id 9
[  104.393280] omap3isp 480bc000.isp: media_gobj_destroy id 93: data link id 83 ==> id 9
[  104.393371] omap3isp 480bc000.isp: media_gobj_destroy id 82: sink pad 'jt8ew9 scaler 1-0010':0
[  104.393493] omap3isp 480bc000.isp: media_gobj_destroy id 83: source pad 'jt8ew9 scaler 1-0010':1
[  104.393585] omap3isp 480bc000.isp: media_gobj_destroy id 81: entity 'jt8ew9 scaler 1-0010'
[  104.394805] omap3isp 480bc000.isp: media_gobj_destroy id 115: intf_devnode v4l-subdev - major: 81, minor: 17
[  104.439941] smiapp 1-0010: flip 0
[  104.440032] smiapp 1-0010: new pixel order GRBG
[  104.442810] smiapp 1-0010: 0x00021700 "min_frame_length_lines_bin" = 192, 0xc0
[  104.443359] smiapp 1-0010: 0x00021702 "max_frame_length_lines_bin" = 65535, 0xffff
[  104.448059] smiapp 1-0010: 0x00021704 "min_line_length_pck_bin" = 1104, 0x450
[  104.448608] smiapp 1-0010: 0x00021706 "max_line_length_pck_bin" = 16382, 0x3ffe
[  104.449127] smiapp 1-0010: 0x00021708 "min_line_blanking_pck_bin" = 200, 0xc8
[  104.449584] smiapp 1-0010: 0x0002170a "fine_integration_time_min_bin" = 0, 0x0
[  104.450073] smiapp 1-0010: 0x0002170c "fine_integration_time_max_margin_bin" = 0, 0x0
[  104.450225] smiapp 1-0010: vblank		40
[  104.450286] smiapp 1-0010: hblank		200
[  104.450347] smiapp 1-0010: real timeperframe	100/837
[  104.463836] smiapp 1-0010: lanes 2
[  104.463958] smiapp 1-0010: nvm 1024, clk 9600000, csi 2
[  104.464019] smiapp 1-0010: freq 0: 199200000
[  104.464080] smiapp 1-0010: freq 1: 210000000
[  104.464141] smiapp 1-0010: freq 2: 499200000
[  104.465606] smiapp 1-0010: GPIO lookup for consumer xshutdown
[  104.465698] smiapp 1-0010: using device tree for GPIO lookup
[  104.465789] of_get_named_gpiod_flags: can't parse 'xshutdown-gpios' property of node '/ocp@68000000/i2c@48072000/camera@10[0]'
[  104.465911] of_get_named_gpiod_flags: can't parse 'xshutdown-gpio' property of node '/ocp@68000000/i2c@48072000/camera@10[0]'
[  104.466003] smiapp 1-0010: using lookup tables for GPIO lookup
[  104.466156] smiapp 1-0010: lookup for GPIO xshutdown failed
[  104.504943] smiapp 1-0010: module 0x0c-0x560f
[  104.505035] smiapp 1-0010: module revision 0x03-0x04 date 11-05-31
[  104.505096] smiapp 1-0010: sensor 0x0c-0x0905
[  104.505157] smiapp 1-0010: sensor revision 0x02 firmware version 0x00
[  104.505249] smiapp 1-0010: smia version 10 smiapp version 08
[  104.505310] smiapp 1-0010: the sensor is called jt8ew9, ident 0c560f03
[  104.505767] smiapp 1-0010: 0x00020080 "analogue_gain_capability" = 0, 0x0
[  104.512725] smiapp 1-0010: 0x00020084 "analogue_gain_code_min" = 68, 0x44
[  104.513244] smiapp 1-0010: 0x00020086 "analogue_gain_code_max" = 544, 0x220
[  104.513671] smiapp 1-0010: 0x00010802 "ths_zero_min" = 104, 0x68
[  104.514984] smiapp 1-0010: 0x00010804 "tclk_trail_min" = 64, 0x40
[  104.516143] smiapp 1-0010: 0x00021000 "integration_time_capability" = 0, 0x0
[  104.521514] smiapp 1-0010: 0x00021004 "coarse_integration_time_min" = 0, 0x0
[  104.522033] smiapp 1-0010: 0x00021006 "coarse_integration_time_max_margin" = 8, 0x8
[  104.522491] smiapp 1-0010: 0x00021008 "fine_integration_time_min" = 0, 0x0
[  104.523590] smiapp 1-0010: 0x0002100a "fine_integration_time_max_margin" = 0, 0x0
[  104.524444] smiapp 1-0010: 0x00021080 "digital_gain_capability" = 1, 0x1
[  104.527923] smiapp 1-0010: 0x00021084 "digital_gain_min" = 0, 0x0
[  104.528411] smiapp 1-0010: 0x00021086 "digital_gain_max" = 1023, 0x3ff
[  104.528900] smiapp 1-0010: 0x01041100 "min_ext_clk_freq_hz" = 6000000, 0x5b8d80
[  104.529418] smiapp 1-0010: 0x01041104 "max_ext_clk_freq_hz" = 27000000, 0x19bfcc0
[  104.533569] smiapp 1-0010: 0x00021108 "min_pre_pll_clk_div" = 1, 0x1
[  104.534057] smiapp 1-0010: 0x0002110a "max_pre_pll_clk_div" = 2, 0x2
[  104.536071] smiapp 1-0010: 0x0104110c "min_pll_ip_freq_hz" = 5000000, 0x4c4b40
[  104.537994] smiapp 1-0010: 0x01041110 "max_pll_ip_freq_hz" = 27000000, 0x19bfcc0
[  104.538482] smiapp 1-0010: 0x00021114 "min_pll_multiplier" = 36, 0x24
[  104.542999] smiapp 1-0010: 0x00021116 "max_pll_multiplier" = 400, 0x190
[  104.543579] smiapp 1-0010: 0x01041118 "min_pll_op_freq_hz" = 1000000000, 0x3b9aca00
[  104.544097] smiapp 1-0010: 0x0104111c "max_pll_op_freq_hz" = 2000000000, 0x77359400
[  104.547637] smiapp 1-0010: 0x00021120 "min_vt_sys_clk_div" = 1, 0x1
[  104.548156] smiapp 1-0010: 0x00021122 "max_vt_sys_clk_div" = 12, 0xc
[  104.548675] smiapp 1-0010: 0x01041124 "min_vt_sys_clk_freq_hz" = 83329994, 0x4f783ca
[  104.549194] smiapp 1-0010: 0x01041128 "max_vt_sys_clk_freq_hz" = 2000000000, 0x77359400
[  104.549713] smiapp 1-0010: 0x0104112c "min_vt_pix_clk_freq_hz" = 40000000, 0x2625a00
[  104.550262] smiapp 1-0010: 0x01041130 "max_vt_pix_clk_freq_hz" = 262000000, 0xf9dcd80
[  104.550720] smiapp 1-0010: 0x00021134 "min_vt_pix_clk_div" = 2, 0x2
[  104.551177] smiapp 1-0010: 0x00021136 "max_vt_pix_clk_div" = 12, 0xc
[  104.551605] smiapp 1-0010: 0x00021140 "min_frame_length_lines" = 192, 0xc0
[  104.553192] smiapp 1-0010: 0x00021142 "max_frame_length_lines" = 65535, 0xffff
[  104.553680] smiapp 1-0010: 0x00021144 "min_line_length_pck" = 2008, 0x7d8
[  104.554138] smiapp 1-0010: 0x00021146 "max_line_length_pck" = 16382, 0x3ffe
[  104.561035] smiapp 1-0010: 0x00021148 "min_line_blanking_pck" = 200, 0xc8
[  104.561645] smiapp 1-0010: 0x0002114a "min_frame_blanking_lines" = 40, 0x28
[  104.562164] smiapp 1-0010: 0x0001114c "min_line_length_pck_step_size" = 2, 0x2
[  104.562622] smiapp 1-0010: 0x00021160 "min_op_sys_clk_div" = 1, 0x1
[  104.563140] smiapp 1-0010: 0x00021162 "max_op_sys_clk_div" = 12, 0xc
[  104.563659] smiapp 1-0010: 0x01041164 "min_op_sys_clk_freq_hz" = 400000000, 0x17d78400
[  104.564239] smiapp 1-0010: 0x01041168 "max_op_sys_clk_freq_hz" = 2000000000, 0x77359400
[  104.564697] smiapp 1-0010: 0x0002116c "min_op_pix_clk_div" = 6, 0x6
[  104.565155] smiapp 1-0010: 0x0002116e "max_op_pix_clk_div" = 10, 0xa
[  104.565734] smiapp 1-0010: 0x01041170 "min_op_pix_clk_freq_hz" = 50000000, 0x2faf080
[  104.567718] smiapp 1-0010: 0x01041174 "max_op_pix_clk_freq_hz" = 250000000, 0xee6b280
[  104.568267] smiapp 1-0010: 0x00021180 "x_addr_min" = 0, 0x0
[  104.568695] smiapp 1-0010: 0x00021182 "y_addr_min" = 0, 0x0
[  104.570556] smiapp 1-0010: 0x00021184 "x_addr_max" = 3599, 0xe0f
[  104.571044] smiapp 1-0010: 0x00021186 "y_addr_max" = 2463, 0x99f
[  104.571472] smiapp 1-0010: 0x00021188 "min_x_output_size" = 184, 0xb8
[  104.573181] smiapp 1-0010: 0x0002118a "min_y_output_size" = 152, 0x98
[  104.577911] smiapp 1-0010: 0x0002118c "max_x_output_size" = 3576, 0xdf8
[  104.579193] smiapp 1-0010: 0x0002118e "max_y_output_size" = 2464, 0x9a0
[  104.579681] smiapp 1-0010: 0x000211c0 "min_even_inc" = 1, 0x1
[  104.580230] smiapp 1-0010: 0x000211c2 "max_even_inc" = 1, 0x1
[  104.580688] smiapp 1-0010: 0x000211c4 "min_odd_inc" = 1, 0x1
[  104.581176] smiapp 1-0010: 0x000211c6 "max_odd_inc" = 1, 0x1
[  104.581604] smiapp 1-0010: 0x00021200 "scaling_capability" = 2, 0x2
[  104.584808] smiapp 1-0010: 0x00021204 "scaler_m_min" = 16, 0x10
[  104.585327] smiapp 1-0010: 0x00021206 "scaler_m_max" = 255, 0xff
[  104.585754] smiapp 1-0010: 0x00021208 "scaler_n_min" = 16, 0x10
[  104.586212] smiapp 1-0010: 0x0002120a "scaler_n_max" = 16, 0x10
[  104.588195] smiapp 1-0010: 0x0002120c "spatial_sampling_capability" = 3, 0x3
[  104.588775] smiapp 1-0010: 0x0001120e "digital_crop_capability" = 1, 0x1
[  104.589202] smiapp 1-0010: 0x00021300 "compression_capability" = 1, 0x1
[  104.589630] smiapp 1-0010: 0x00011502 "fifo_support_capability" = 1, 0x1
[  104.590057] smiapp 1-0010: 0x00011600 "dphy_ctrl_capability" = 30, 0x1e
[  104.591125] smiapp 1-0010: 0x00011601 "csi_lane_mode_capability" = 3, 0x3
[  104.591552] smiapp 1-0010: 0x00011602 "csi_signalling_mode_capability" = 7, 0x7
[  104.592010] smiapp 1-0010: 0x00011603 "fast_standby_capability" = 1, 0x1
[  104.593170] smiapp 1-0010: 0x00011604 "cci_address_control_capability" = 1, 0x1
[  104.611785] smiapp 1-0010: 0x00041608 "max_per_lane_bitrate_1_lane_mode_mbps" = 65536000, 0x3e80000
[  104.612396] smiapp 1-0010: 0x0004160c "max_per_lane_bitrate_2_lane_mode_mbps" = 65536000, 0x3e80000
[  104.612976] smiapp 1-0010: 0x00041610 "max_per_lane_bitrate_3_lane_mode_mbps" = 0, 0x0
[  104.613555] smiapp 1-0010: 0x00041614 "max_per_lane_bitrate_4_lane_mode_mbps" = 0, 0x0
[  104.614105] smiapp 1-0010: 0x00011618 "temp_sensor_capability" = 0, 0x0
[  104.614624] smiapp 1-0010: 0x00021700 "min_frame_length_lines_bin" = 192, 0xc0
[  104.615142] smiapp 1-0010: 0x00021702 "max_frame_length_lines_bin" = 65535, 0xffff
[  104.615661] smiapp 1-0010: 0x00021704 "min_line_length_pck_bin" = 1104, 0x450
[  104.618011] smiapp 1-0010: 0x00021706 "max_line_length_pck_bin" = 16382, 0x3ffe
[  104.618652] smiapp 1-0010: 0x00021708 "min_line_blanking_pck_bin" = 200, 0xc8
[  104.619171] smiapp 1-0010: 0x0002170a "fine_integration_time_min_bin" = 0, 0x0
[  104.619689] smiapp 1-0010: 0x0002170c "fine_integration_time_max_margin_bin" = 0, 0x0
[  104.620239] smiapp 1-0010: 0x00011710 "binning_capability" = 1, 0x1
[  104.620758] smiapp 1-0010: 0x00011711 "binning_weighting_capability" = 5, 0x5
[  104.621276] smiapp 1-0010: 0x00011800 "data_transfer_if_capability" = 13, 0xd
[  104.621795] smiapp 1-0010: 0x00011900 "shading_correction_capability" = 0, 0x0
[  104.622344] smiapp 1-0010: 0x00011901 "green_imbalance_capability" = 0, 0x0
[  104.622863] smiapp 1-0010: 0x00011902 "black_level_capability" = 0, 0x0
[  104.623382] smiapp 1-0010: 0x00011903 "module_specific_correction_capability" = 0, 0x0
[  104.623901] smiapp 1-0010: 0x00021904 "defect_correction_capability" = 865, 0x361
[  104.624450] smiapp 1-0010: 0x00021906 "defect_correction_capability_2" = 0, 0x0
[  104.624969] smiapp 1-0010: 0x00011980 "edof_capability" = 0, 0x0
[  104.625488] smiapp 1-0010: 0x00011987 "colour_feedback_capability" = 0, 0x0
[  104.626007] smiapp 1-0010: 0x000119c0 "estimation_mode_capability" = 0, 0x0
[  104.628265] smiapp 1-0010: 0x000119c1 "estimation_zone_capability" = 0, 0x0
[  104.628814] smiapp 1-0010: 0x00021a00 "capability_trdy_min" = 0, 0x0
[  104.629333] smiapp 1-0010: 0x00011a02 "flash_mode_capability" = 3, 0x3
[  104.629852] smiapp 1-0010: 0x00011b04 "actuator_capability" = 4, 0x4
[  104.630340] smiapp 1-0010: 0x00011c00 "bracketing_lut_capability_1" = 3, 0x3
[  104.630859] smiapp 1-0010: 0x00011c01 "bracketing_lut_capability_2" = 0, 0x0
[  104.631378] smiapp 1-0010: 0x00020088 "analogue_gain_code_step" = 1, 0x1
[  104.632324] smiapp 1-0010: format_model_type 2 byte
[  104.632843] smiapp 1-0010: 0x00020042 visible pixels: 3576 columns (pixelcode 5)
[  104.633361] smiapp 1-0010: 0x00020044 embedded pixels: 2 rows (pixelcode 1)
[  104.633880] smiapp 1-0010: 0x00020046 visible pixels: 2464 rows (pixelcode 5)
[  104.633972] smiapp 1-0010: embedded data from lines 0 to 2
[  104.634033] smiapp 1-0010: image data starts at line 2
[  104.634094] smiapp 1-0010: quirk: 0x00020084 "analogue_gain_code_min" = 59, 0x3b
[  104.634185] smiapp 1-0010: quirk: 0x00020086 "analogue_gain_code_max" = 6000, 0x1770
[  104.635162] smiapp 1-0010: binning 2x1
[  104.635650] smiapp 1-0010: binning 3x1
[  104.636138] smiapp 1-0010: binning 4x1
[  104.638305] smiapp 1-0010: binning 5x1
[  104.638824] smiapp 1-0010: binning 6x1
[  104.639312] smiapp 1-0010: binning 7x1
[  104.639801] smiapp 1-0010: binning 8x1
[  104.640289] smiapp 1-0010: binning 1x2
[  104.640777] smiapp 1-0010: binning 2x2
[  104.641296] smiapp 1-0010: binning 3x2
[  104.641784] smiapp 1-0010: binning 4x2
[  104.642272] smiapp 1-0010: binning 5x2
[  104.642791] smiapp 1-0010: binning 6x2
[  104.643280] smiapp 1-0010: binning 7x2
[  104.643768] smiapp 1-0010: binning 8x2
[  104.644073] smiapp 1-0010: profile 2
[  104.645080] smiapp 1-0010: data_format_model_type 1
[  104.645599] smiapp 1-0010: pixel order 0 (GRBG)
[  104.646118] smiapp 1-0010: 0: bpp 8, compressed 8
[  104.647705] smiapp 1-0010: jolly good! 20
[  104.648284] smiapp 1-0010: 1: bpp 10, compressed 10
[  104.648345] smiapp 1-0010: jolly good! 12
[  104.648864] smiapp 1-0010: 2: bpp 10, compressed 8
[  104.648925] smiapp 1-0010: jolly good! 16
[  104.649414] smiapp 1-0010: 3: bpp 10, compressed 6
[  104.649902] smiapp 1-0010: 4: bpp 0, compressed 0
[  104.650421] smiapp 1-0010: 5: bpp 0, compressed 0
[  104.650909] smiapp 1-0010: 6: bpp 0, compressed 0
[  104.651397] smiapp 1-0010: 7: bpp 0, compressed 0
[  104.651519] smiapp 1-0010: link freq 199200000 Hz, bpp 10 ok
[  104.651580] smiapp 1-0010: link freq 210000000 Hz, bpp 10 ok
[  104.651672] smiapp 1-0010: link freq 499200000 Hz, bpp 10 ok
[  104.651733] smiapp 1-0010: link freq 199200000 Hz, bpp 8 ok
[  104.651824] smiapp 1-0010: link freq 210000000 Hz, bpp 8 ok
[  104.651885] smiapp 1-0010: link freq 499200000 Hz, bpp 8 ok
[  104.651947] smiapp 1-0010: link freq 199200000 Hz, bpp 8 ok
[  104.652038] smiapp 1-0010: link freq 210000000 Hz, bpp 8 ok
[  104.652099] smiapp 1-0010: link freq 499200000 Hz, bpp 8 ok
[  104.652160] smiapp 1-0010: flip 0
[  104.652221] smiapp 1-0010: new pixel order GRBG
[  104.653167] smiapp 1-0010: 0x00021700 "min_frame_length_lines_bin" = 192, 0xc0
[  104.653717] smiapp 1-0010: 0x00021702 "max_frame_length_lines_bin" = 65535, 0xffff
[  104.654235] smiapp 1-0010: 0x00021704 "min_line_length_pck_bin" = 1104, 0x450
[  104.654754] smiapp 1-0010: 0x00021706 "max_line_length_pck_bin" = 16382, 0x3ffe
[  104.655303] smiapp 1-0010: 0x00021708 "min_line_blanking_pck_bin" = 200, 0xc8
[  104.655792] smiapp 1-0010: 0x0002170a "fine_integration_time_min_bin" = 0, 0x0
[  104.658355] smiapp 1-0010: 0x0002170c "fine_integration_time_max_margin_bin" = 0, 0x0
[  104.659240] smiapp 1-0010: vblank		40
[  104.659332] smiapp 1-0010: hblank		200
[  104.659362] smiapp 1-0010: real timeperframe	100/837
[  104.662078] omap3isp 480bc000.isp: media_gobj_destroy id 98: interface link id 97 ==> id 8
[  104.662231] omap3isp 480bc000.isp: media_gobj_destroy id 52: data link id 10 ==> id 12
[  104.662322] omap3isp 480bc000.isp: media_gobj_destroy id 51: data link id 10 ==> id 12
[  104.662414] omap3isp 480bc000.isp: media_gobj_destroy id 66: data link id 10 ==> id 16
[  104.662536] omap3isp 480bc000.isp: media_gobj_destroy id 65: data link id 10 ==> id 16
[  104.662628] omap3isp 480bc000.isp: media_gobj_destroy id 9: sink pad 'OMAP3 ISP CSI2a':0
[  104.662719] omap3isp 480bc000.isp: media_gobj_destroy id 10: source pad 'OMAP3 ISP CSI2a':1
[  104.662811] omap3isp 480bc000.isp: media_gobj_destroy id 8: entity 'OMAP3 ISP CSI2a'
[  104.673797] omap3isp 480bc000.isp: media_gobj_destroy id 97: intf_devnode v4l-subdev - major: 81, minor: 8
[  104.675140] omap3isp 480bc000.isp: media_gobj_destroy id 14: interface link id 13 ==> id 11
[  104.675262] omap3isp 480bc000.isp: media_gobj_destroy id 13: intf_devnode v4l-video - major: 81, minor: 1
[  104.675384] omap3isp 480bc000.isp: media_gobj_destroy id 12: sink pad 'OMAP3 ISP CSI2a output':0
[  104.675506] omap3isp 480bc000.isp: media_gobj_destroy id 11: entity 'OMAP3 ISP CSI2a output'
[  104.675628] omap3isp 480bc000.isp: media_gobj_destroy id 96: interface link id 95 ==> id 1
[  104.675720] omap3isp 480bc000.isp: media_gobj_destroy id 53: data link id 5 ==> id 2
[  104.675811] omap3isp 480bc000.isp: media_gobj_destroy id 54: data link id 5 ==> id 2
[  104.675933] omap3isp 480bc000.isp: media_gobj_destroy id 68: data link id 3 ==> id 16
[  104.676025] omap3isp 480bc000.isp: media_gobj_destroy id 67: data link id 3 ==> id 16
[  104.676116] omap3isp 480bc000.isp: media_gobj_destroy id 2: sink pad 'OMAP3 ISP CCP2':0
[  104.690277] omap3isp 480bc000.isp: media_gobj_destroy id 3: source pad 'OMAP3 ISP CCP2':1
[  104.690429] omap3isp 480bc000.isp: media_gobj_destroy id 1: entity 'OMAP3 ISP CCP2'
[  104.691741] omap3isp 480bc000.isp: media_gobj_destroy id 95: intf_devnode v4l-subdev - major: 81, minor: 7
[  104.697937] omap3isp 480bc000.isp: media_gobj_destroy id 7: interface link id 6 ==> id 4
[  104.698089] omap3isp 480bc000.isp: media_gobj_destroy id 6: intf_devnode v4l-video - major: 81, minor: 0
[  104.698211] omap3isp 480bc000.isp: media_gobj_destroy id 5: source pad 'OMAP3 ISP CCP2 input':0
[  104.698303] omap3isp 480bc000.isp: media_gobj_destroy id 4: entity 'OMAP3 ISP CCP2 input'
[  104.698425] omap3isp 480bc000.isp: media_gobj_destroy id 100: interface link id 99 ==> id 15
[  104.698547] omap3isp 480bc000.isp: media_gobj_destroy id 56: data link id 17 ==> id 20
[  104.698638] omap3isp 480bc000.isp: media_gobj_destroy id 55: data link id 17 ==> id 20
[  104.698852] omap3isp 480bc000.isp: media_gobj_destroy id 70: data link id 18 ==> id 24
[  104.698974] omap3isp 480bc000.isp: media_gobj_destroy id 69: data link id 18 ==> id 24
[  104.699066] omap3isp 480bc000.isp: media_gobj_destroy id 72: data link id 17 ==> id 35
[  104.699188] omap3isp 480bc000.isp: media_gobj_destroy id 71: data link id 17 ==> id 35
[  104.699279] omap3isp 480bc000.isp: media_gobj_destroy id 76: data link id 18 ==> id 46
[  104.699371] omap3isp 480bc000.isp: media_gobj_destroy id 75: data link id 18 ==> id 46
[  104.699462] omap3isp 480bc000.isp: media_gobj_destroy id 78: data link id 18 ==> id 48
[  104.699584] omap3isp 480bc000.isp: media_gobj_destroy id 77: data link id 18 ==> id 48
[  104.699676] omap3isp 480bc000.isp: media_gobj_destroy id 80: data link id 18 ==> id 50
[  104.699768] omap3isp 480bc000.isp: media_gobj_destroy id 79: data link id 18 ==> id 50
[  104.699859] omap3isp 480bc000.isp: media_gobj_destroy id 16: sink pad 'OMAP3 ISP CCDC':0
[  104.699981] omap3isp 480bc000.isp: media_gobj_destroy id 17: source pad 'OMAP3 ISP CCDC':1
[  104.700073] omap3isp 480bc000.isp: media_gobj_destroy id 18: source pad 'OMAP3 ISP CCDC':2
[  104.700164] omap3isp 480bc000.isp: media_gobj_destroy id 15: entity 'OMAP3 ISP CCDC'
[  104.709045] omap3isp 480bc000.isp: media_gobj_destroy id 99: intf_devnode v4l-subdev - major: 81, minor: 9
[  104.727142] omap3isp 480bc000.isp: media_gobj_destroy id 22: interface link id 21 ==> id 19
[  104.727294] omap3isp 480bc000.isp: media_gobj_destroy id 21: intf_devnode v4l-video - major: 81, minor: 2
[  104.727416] omap3isp 480bc000.isp: media_gobj_destroy id 20: sink pad 'OMAP3 ISP CCDC output':0
[  104.727539] omap3isp 480bc000.isp: media_gobj_destroy id 19: entity 'OMAP3 ISP CCDC output'
[  104.727661] omap3isp 480bc000.isp: media_gobj_destroy id 102: interface link id 101 ==> id 23
[  104.727752] omap3isp 480bc000.isp: media_gobj_destroy id 57: data link id 27 ==> id 24
[  104.727844] omap3isp 480bc000.isp: media_gobj_destroy id 58: data link id 27 ==> id 24
[  104.727966] omap3isp 480bc000.isp: media_gobj_destroy id 60: data link id 25 ==> id 31
[  104.728057] omap3isp 480bc000.isp: media_gobj_destroy id 59: data link id 25 ==> id 31
[  104.728149] omap3isp 480bc000.isp: media_gobj_destroy id 74: data link id 25 ==> id 35
[  104.728271] omap3isp 480bc000.isp: media_gobj_destroy id 73: data link id 25 ==> id 35
[  104.728363] omap3isp 480bc000.isp: media_gobj_destroy id 24: sink pad 'OMAP3 ISP preview':0
[  104.728454] omap3isp 480bc000.isp: media_gobj_destroy id 25: source pad 'OMAP3 ISP preview':1
[  104.728546] omap3isp 480bc000.isp: media_gobj_destroy id 23: entity 'OMAP3 ISP preview'
[  104.738616] omap3isp 480bc000.isp: media_gobj_destroy id 101: intf_devnode v4l-subdev - major: 81, minor: 10
[  104.743835] omap3isp 480bc000.isp: media_gobj_destroy id 29: interface link id 28 ==> id 26
[  104.743957] omap3isp 480bc000.isp: media_gobj_destroy id 28: intf_devnode v4l-video - major: 81, minor: 3
[  104.744079] omap3isp 480bc000.isp: media_gobj_destroy id 27: source pad 'OMAP3 ISP preview input':0
[  104.744201] omap3isp 480bc000.isp: media_gobj_destroy id 26: entity 'OMAP3 ISP preview input'
[  104.748077] omap3isp 480bc000.isp: media_gobj_destroy id 33: interface link id 32 ==> id 30
[  104.748199] omap3isp 480bc000.isp: media_gobj_destroy id 32: intf_devnode v4l-video - major: 81, minor: 4
[  104.748321] omap3isp 480bc000.isp: media_gobj_destroy id 31: sink pad 'OMAP3 ISP preview output':0
[  104.748413] omap3isp 480bc000.isp: media_gobj_destroy id 30: entity 'OMAP3 ISP preview output'
[  104.748535] omap3isp 480bc000.isp: media_gobj_destroy id 104: interface link id 103 ==> id 34
[  104.748657] omap3isp 480bc000.isp: media_gobj_destroy id 61: data link id 38 ==> id 35
[  104.748748] omap3isp 480bc000.isp: media_gobj_destroy id 62: data link id 38 ==> id 35
[  104.748840] omap3isp 480bc000.isp: media_gobj_destroy id 64: data link id 36 ==> id 42
[  104.748962] omap3isp 480bc000.isp: media_gobj_destroy id 63: data link id 36 ==> id 42
[  104.749053] omap3isp 480bc000.isp: media_gobj_destroy id 35: sink pad 'OMAP3 ISP resizer':0
[  104.749145] omap3isp 480bc000.isp: media_gobj_destroy id 36: source pad 'OMAP3 ISP resizer':1
[  104.749237] omap3isp 480bc000.isp: media_gobj_destroy id 34: entity 'OMAP3 ISP resizer'
[  104.760467] omap3isp 480bc000.isp: media_gobj_destroy id 103: intf_devnode v4l-subdev - major: 81, minor: 11
[  104.787139] omap3isp 480bc000.isp: media_gobj_destroy id 40: interface link id 39 ==> id 37
[  104.787292] omap3isp 480bc000.isp: media_gobj_destroy id 39: intf_devnode v4l-video - major: 81, minor: 5
[  104.787414] omap3isp 480bc000.isp: media_gobj_destroy id 38: source pad 'OMAP3 ISP resizer input':0
[  104.787506] omap3isp 480bc000.isp: media_gobj_destroy id 37: entity 'OMAP3 ISP resizer input'
[  104.794677] omap3isp 480bc000.isp: media_gobj_destroy id 44: interface link id 43 ==> id 41
[  104.794830] omap3isp 480bc000.isp: media_gobj_destroy id 43: intf_devnode v4l-video - major: 81, minor: 6
[  104.794952] omap3isp 480bc000.isp: media_gobj_destroy id 42: sink pad 'OMAP3 ISP resizer output':0
[  104.795074] omap3isp 480bc000.isp: media_gobj_destroy id 41: entity 'OMAP3 ISP resizer output'
[  104.795196] omap3isp 480bc000.isp: media_gobj_destroy id 106: interface link id 105 ==> id 45
[  104.795288] omap3isp 480bc000.isp: media_gobj_destroy id 46: sink pad 'OMAP3 ISP AEWB':0
[  104.795379] omap3isp 480bc000.isp: media_gobj_destroy id 45: entity 'OMAP3 ISP AEWB'
[  104.798339] omap3isp 480bc000.isp: media_gobj_destroy id 105: intf_devnode v4l-subdev - major: 81, minor: 12
[  104.798492] omap3isp 480bc000.isp: media_gobj_destroy id 108: interface link id 107 ==> id 47
[  104.798583] omap3isp 480bc000.isp: media_gobj_destroy id 48: sink pad 'OMAP3 ISP AF':0
[  104.798706] omap3isp 480bc000.isp: media_gobj_destroy id 47: entity 'OMAP3 ISP AF'
[  104.808898] omap3isp 480bc000.isp: media_gobj_destroy id 107: intf_devnode v4l-subdev - major: 81, minor: 13
[  104.809082] omap3isp 480bc000.isp: media_gobj_destroy id 110: interface link id 109 ==> id 49
[  104.809204] omap3isp 480bc000.isp: media_gobj_destroy id 50: sink pad 'OMAP3 ISP histogram':0
[  104.809295] omap3isp 480bc000.isp: media_gobj_destroy id 49: entity 'OMAP3 ISP histogram'
[  104.827026] omap3isp 480bc000.isp: media_gobj_destroy id 109: intf_devnode v4l-subdev - major: 81, minor: 14
[  104.827270] omap3isp 480bc000.isp: Media device unregistered
[  104.850616] omap3isp 480bc000.isp: OMAP3 ISP AEWB: all buffers were freed.
[  104.850738] omap3isp 480bc000.isp: OMAP3 ISP AF: all buffers were freed.
[  104.850830] omap3isp 480bc000.isp: OMAP3 ISP histogram: all buffers were freed.
[  104.852722] clk_unregister: unregistering prepared clock: cam_xclka
[  104.853302] iommu: Removing device 480bc000.isp from group 0
[  105.756408] Unable to handle kernel NULL pointer dereference at virtual address 00000140
[  105.756561] pgd = eda94000
[  105.756591] [00000140] *pgd=adaf8831, *pte=00000000, *ppte=00000000
[  105.756683] Internal error: Oops: 17 [#1] PREEMPT ARM
[  105.756744] Modules linked in: smiapp smiapp_pll omap3_isp videobuf2_dma_contig videobuf2_memops videobuf2_v4l2 videobuf2_core v4l2_common videodev media
[  105.756927] CPU: 0 PID: 2276 Comm: media-ctl Not tainted 4.9.0-rc6-00494-g9244e38-dirty #830
[  105.757019] Hardware name: Generic OMAP36xx (Flattened Device Tree)
[  105.757080] task: ed970380 task.stack: eda5e000
[  105.757141] PC is at __lock_acquire+0x94/0x1868
[  105.757202] LR is at lock_acquire+0x70/0x90
[  105.757263] pc : [<c015e9a8>]    lr : [<c01601ec>]    psr: 20000093
               sp : eda5fcc0  ip : eda5e000  fp : 00000000
[  105.757354] r10: 00000001  r9 : 00000000  r8 : 0002715c
[  105.757415] r7 : 00000140  r6 : 00000001  r5 : 60000013  r4 : ed970380
[  105.757476] r3 : 00000001  r2 : 00000001  r1 : 00000000  r0 : 00000140
[  105.757537] Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment none
[  105.757629] Control: 10c5387d  Table: ada94019  DAC: 00000051
[  105.757690] Process media-ctl (pid: 2276, stack limit = 0xeda5e208)
[  105.757751] Stack: (0xeda5fcc0 to 0xeda60000)
[  105.757812] fcc0: ed970868 00000001 a409df10 c355d08b c0c75714 c01602f4 60000013 00000001
[  105.757904] fce0: ee1c9514 c0839b48 ee1c9518 effed360 ed970868 60000013 c0833e74 c0839b48
[  105.757995] fd00: effed360 effed360 c0e9166c ee1c951c ee1c9518 00000000 60000013 00000001
[  105.758087] fd20: 00000000 0002715c eda5e000 00000000 00000000 c01601ec 00000001 00000000
[  105.758178] fd40: 00000000 bf000e78 00000000 00000000 0000010c bf000e78 ed970380 c04ed214
[  105.758270] fd60: 00000001 00000000 bf000e78 c015aa50 ed9703b0 ed9703b0 c0830d50 00000000
[  105.758361] fd80: ed970848 c0830d60 ed970380 ed970380 c0830d60 c01602f4 c0e76744 00000051
[  105.758483] fda0: eda5fdd0 00000000 0002715c eda5fdd0 bf002e28 c1007c01 00000000 0002715c
[  105.758575] fdc0: eda5e000 00000000 00000000 bf000e78 00000001 50414d4f 53492033 43432050
[  105.758666] fde0: 00003250 00000000 00000000 00000000 00000000 00020000 00000000 00000000
[  105.758758] fe00: 00000000 00010002 00000000 00000000 00000000 00000000 00000051 00000007
[  105.758850] fe20: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  105.758941] fe40: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  105.759033] fe60: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  105.759124] fe80: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  105.759216] fea0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  105.759307] fec0: 00000000 00000000 00000000 00000000 ed967c80 bf000ddc ed967c80 0002715c
[  105.759399] fee0: c1007c01 00000003 00000000 bf001808 0002715c ed967c80 00000003 ed9fece0
[  105.759490] ff00: 00000003 c01ea4c4 0002715c c01eb4a8 00000000 00000000 c01fba18 ffffffff
[  105.759582] ff20: 00000001 00000000 ee84f010 ed89e440 00000000 ee2654e8 00000010 c01dacdc
[  105.759674] ff40: 00000000 00000000 00000000 ed89e538 ed8a2b50 ed9707a0 ed970380 00000000
[  105.759765] ff60: eda5ff7c eda5ff84 ed967c80 ed967c80 0002715c c1007c01 00000003 eda5e000
[  105.759857] ff80: 00000000 c01eb560 0002715c 00027008 00000000 00000036 c0107d84 eda5e000
[  105.759948] ffa0: 00000000 c0107be0 0002715c 00027008 00000003 c1007c01 0002715c 80000000
[  105.760070] ffc0: 0002715c 00027008 00000000 00000036 00027158 00000000 b6f71000 00000000
[  105.760162] ffe0: 00026b08 be9cf85c 000126a4 b6eaaa5c 20000010 00000003 fda7fddf fdbdffba
[  105.760253] [<c015e9a8>] (__lock_acquire) from [<c01601ec>] (lock_acquire+0x70/0x90)
[  105.760375] [<c01601ec>] (lock_acquire) from [<c04ed214>] (mutex_lock_nested+0x54/0x3f4)
[  105.760528] [<c04ed214>] (mutex_lock_nested) from [<bf000e78>] (media_device_ioctl+0x9c/0x120 [media])
[  105.760681] [<bf000e78>] (media_device_ioctl [media]) from [<bf001808>] (media_ioctl+0x54/0x60 [media])
[  105.760803] [<bf001808>] (media_ioctl [media]) from [<c01ea4c4>] (vfs_ioctl+0x18/0x30)
[  105.760894] [<c01ea4c4>] (vfs_ioctl) from [<c01eb4a8>] (do_vfs_ioctl+0x90c/0x974)
[  105.760986] [<c01eb4a8>] (do_vfs_ioctl) from [<c01eb560>] (SyS_ioctl+0x50/0x6c)
[  105.761108] [<c01eb560>] (SyS_ioctl) from [<c0107be0>] (ret_fast_syscall+0x0/0x1c)
[  105.761199] Code: e59f3f58 e593300c e3530000 0a000003 (e5972000) 
[  105.761260] ---[ end trace bdb47e9a97e34f03 ]---
[  105.761322] note: media-ctl[2276] exited with preempt_count 1
[  105.762145] media: media_release: Media Release
[  105.762237] platform 480bc000.isp: Media device released
[  105.762298] media: media_devnode_release: Media Devnode Deallocated
[  106.076416] ------------[ cut here ]------------
[  106.076538] WARNING: CPU: 0 PID: 56 at drivers/clk/clk.c:2664 clk_core_disable+0x9c/0xb0
[  106.076599] Modules linked in: smiapp smiapp_pll omap3_isp videobuf2_dma_contig videobuf2_memops videobuf2_v4l2 videobuf2_core v4l2_common videodev media
[  106.076812] CPU: 0 PID: 56 Comm: kworker/0:1 Tainted: G      D         4.9.0-rc6-00494-g9244e38-dirty #830
[  106.076904] Hardware name: Generic OMAP36xx (Flattened Device Tree)
[  106.076995] Workqueue: pm pm_runtime_work
[  106.077087] [<c010dc8c>] (unwind_backtrace) from [<c010b6a0>] (show_stack+0x10/0x14)
[  106.077178] [<c010b6a0>] (show_stack) from [<c012a564>] (__warn+0xc8/0xf4)
[  106.077270] [<c012a564>] (__warn) from [<c012a5ac>] (warn_slowpath_null+0x1c/0x20)
[  106.077362] [<c012a5ac>] (warn_slowpath_null) from [<c02fb0ec>] (clk_core_disable+0x9c/0xb0)
[  106.077453] [<c02fb0ec>] (clk_core_disable) from [<c02fb704>] (clk_core_disable_lock+0x18/0x24)
[  106.077606] [<c02fb704>] (clk_core_disable_lock) from [<bf09296c>] (smiapp_power_off+0x44/0x70 [smiapp])
[  106.077728] [<bf09296c>] (smiapp_power_off [smiapp]) from [<c034b020>] (__rpm_callback+0x30/0x58)
[  106.077819] [<c034b020>] (__rpm_callback) from [<c034b0b4>] (rpm_callback+0x6c/0x7c)
[  106.077911] [<c034b0b4>] (rpm_callback) from [<c034b658>] (rpm_suspend+0x264/0x48c)
[  106.078033] [<c034b658>] (rpm_suspend) from [<c034c728>] (pm_runtime_work+0x7c/0x98)
[  106.078124] [<c034c728>] (pm_runtime_work) from [<c0142f90>] (process_one_work+0x214/0x43c)
[  106.078216] [<c0142f90>] (process_one_work) from [<c0143590>] (worker_thread+0x3d8/0x52c)
[  106.078308] [<c0143590>] (worker_thread) from [<c0148924>] (kthread+0xdc/0xe8)
[  106.078430] [<c0148924>] (kthread) from [<c0107c70>] (ret_from_fork+0x14/0x24)
[  106.078491] ---[ end trace bdb47e9a97e34f04 ]---
[  216.811340] systemd-logind[2167]: New session c4 of user sailus.
[  227.091491] systemd-logind[2167]: New session c5 of user sailus.
[  273.464019] systemd-logind[2167]: New session c6 of user sailus.
[  280.322326] systemd-logind[2167]: New session c7 of user sailus.
[  284.116516] systemd-logind[2167]: New session c8 of user sailus.

Re: [PATCH RFC] omap3isp: prevent releasing MC too early

[Laurent Pinchart]

Hi Mauro,

On Friday 16 Dec 2016 09:18:50 Mauro Carvalho Chehab wrote:
> Em Thu, 15 Dec 2016 16:04:51 +0200 Laurent Pinchart escreveu:
> 
> We have now two threads discussing the same subject, which is bad, as
> we'll end repeating the same arguments on different threads...
> 
> Let's use the "[PATCH RFC 00/21]" for those discussions, as it seems we're
> reaching to somewhere there.
> 
> > Even if you're not entirely convinced by the reasons
> > explained in this mail thread, remember that we will need sooner or later
> > to implement support for media graph update at runtime. Refcounting will
> > be needed, let's design it in the cleanest possible way.
> 
> As I said, I'm not against using some other approach and even
> adding refcounting to each graph object.
> 
> What I am against is on a patchset that starts by breaking
> the USB drivers that use the media controller.

So, what you're essentially saying, is that you noticed we have a problem in 
the core when trying to add MC support to a bunch of USB driver. Instead of 
fixing the problem properly, you've merged 3 patches that work around part of 
the issue, despite negative comments received by the original authors of the 
code, and then added a bunch of code to the USB drivers that make them subject 
to the race condition. And you're then claiming that we can't revert the 
patches that we know from the start were broken because you piled additional 
patches on top of them, making the end result worse ? Sorry, I can't buy that. 
If you really insist we can also revert the series that add MC support to the 
USB drivers, but there's no way that your decision to ignore known issues can 
ever be considered as an excuse to not revert broken changes.

This discussion is over as far as I'm concerned. The 3 patches in question are 
wrong. I want the proper fixes to be merged, and we thus all need to work in 
that direction, which means reviewing them. Once we agree on what the end 
result should be we'll see whether we could possibly rework the code in a way 
that doesn't require a revert. If that's not possible, we'll revert what is 
broken. It's as simple as that. Now, let's get technical and fix this crap. If 
I had wanted a show I would have bought tickets to the circus.

> Btw, I'm starting to suspect that getting rid of devm_*alloc()
> on OMAP3, as proposed by the 00/21 thread is addressing a symptom of
> the problem and not a cause, and that using get_device()/put_device()
> may help fixing such issues. See Hans comments on that thread.

-- 
Regards,

Laurent Pinchart