[PATCH 2/3] media: i2c: ov9282: add led_mode v4l2 control

[Richard Leitner <richard.leitner@linux.dev>]

Add V4L2_CID_FLASH_LED_MODE support using the "strobe output enable"
feature of the sensor. This implements following modes:

 - V4L2_FLASH_LED_MODE_NONE, which disables the strobe output
 - V4L2_FLASH_LED_MODE_FLASH, which enables the strobe output

All values are based on the OV9281 datasheet v1.53 (january 2019) and
tested using an ov9281 VisionComponents module.

Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
---
 drivers/media/i2c/ov9282.c | 29 +++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)

diff --git a/drivers/media/i2c/ov9282.c b/drivers/media/i2c/ov9282.c
index f42e0d439753e74d14e3a3592029e48f49234927..c98ba466e9aea29baff0b13578d760bf69c958c5 100644
--- a/drivers/media/i2c/ov9282.c
+++ b/drivers/media/i2c/ov9282.c
@@ -192,6 +192,7 @@ struct ov9282_mode {
  * @exp_ctrl: Pointer to exposure control
  * @again_ctrl: Pointer to analog gain control
  * @pixel_rate: Pointer to pixel rate control
+ * @flash_led_mode: Pointer to flash led mode control
  * @vblank: Vertical blanking in lines
  * @noncontinuous_clock: Selection of CSI2 noncontinuous clock mode
  * @cur_mode: Pointer to current selected sensor mode
@@ -214,6 +215,7 @@ struct ov9282 {
 		struct v4l2_ctrl *again_ctrl;
 	};
 	struct v4l2_ctrl *pixel_rate;
+	struct v4l2_ctrl *flash_led_mode;
 	u32 vblank;
 	bool noncontinuous_clock;
 	const struct ov9282_mode *cur_mode;
@@ -670,6 +672,23 @@ static int ov9282_set_ctrl_vflip(struct ov9282 *ov9282, int value)
 				current_val);
 }
 
+static int ov9282_set_ctrl_flash_led_mode(struct ov9282 *ov9282, int mode)
+{
+	u32 current_val;
+	int ret = ov9282_read_reg(ov9282, OV9282_REG_OUTPUT_ENABLE6, 1,
+				  &current_val);
+	if (ret)
+		return ret;
+
+	if (mode == V4L2_FLASH_LED_MODE_FLASH)
+		current_val |= OV9282_OUTPUT_ENABLE6_STROBE;
+	else
+		current_val &= ~OV9282_OUTPUT_ENABLE6_STROBE;
+
+	return ov9282_write_reg(ov9282, OV9282_REG_OUTPUT_ENABLE6, 1,
+				current_val);
+}
+
 /**
  * ov9282_set_ctrl() - Set subdevice control
  * @ctrl: pointer to v4l2_ctrl structure
@@ -736,6 +755,9 @@ static int ov9282_set_ctrl(struct v4l2_ctrl *ctrl)
 		ret = ov9282_write_reg(ov9282, OV9282_REG_TIMING_HTS, 2,
 				       (ctrl->val + ov9282->cur_mode->width) >> 1);
 		break;
+	case V4L2_CID_FLASH_LED_MODE:
+		ret = ov9282_set_ctrl_flash_led_mode(ov9282, ctrl->val);
+		break;
 	default:
 		dev_err(ov9282->dev, "Invalid control %d", ctrl->id);
 		ret = -EINVAL;
@@ -1391,6 +1413,13 @@ static int ov9282_init_controls(struct ov9282 *ov9282)
 						OV9282_TIMING_HTS_MAX - mode->width,
 						1, hblank_min);
 
+	/* Flash/Strobe controls */
+	ov9282->flash_led_mode = v4l2_ctrl_new_std_menu(ctrl_hdlr, &ov9282_ctrl_ops,
+							V4L2_CID_FLASH_LED_MODE,
+							V4L2_FLASH_LED_MODE_TORCH,
+							(1 << V4L2_FLASH_LED_MODE_TORCH),
+							V4L2_FLASH_LED_MODE_NONE);
+
 	ret = v4l2_fwnode_device_parse(ov9282->dev, &props);
 	if (!ret) {
 		/* Failure sets ctrl_hdlr->error, which we check afterwards anyway */

-- 
2.47.2