From: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
To: "Niklas Söderlund" <niklas.soderlund@ragnatech.se>,
"Mauro Carvalho Chehab" <mchehab@kernel.org>,
"Sakari Ailus" <sakari.ailus@linux.intel.com>
Cc: linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org,
linux-kernel@vger.kernel.org,
"Niklas Söderlund" <niklas.soderlund+renesas@ragnatech.se>,
"Mauro Carvalho Chehab" <mchehab+huawei@kernel.org>,
"Laurent Pinchart" <laurent.pinchart@ideasonboard.com>,
"Jacopo Mondi" <jacopo.mondi@ideasonboard.com>,
"Tomi Valkeinen" <tomi.valkeinen+renesas@ideasonboard.com>
Subject: [PATCH v7 04/11] media: rcar-csi2: Move {enable|disable}_streams() calls
Date: Tue, 08 Sep 2026 09:33:08 +0300 [thread overview]
Message-ID: <20260908-rcar-streams-v7-4-c406a2c2930f@ideasonboard.com> (raw)
In-Reply-To: <20260908-rcar-streams-v7-0-c406a2c2930f@ideasonboard.com>
With multiple streams the operation to enable the CSI-2 hardware and to
call {enable|disable}_streams() on upstream subdev will need to be
handled separately.
Prepare for that by moving {enable|disable}_streams() calls out from
rcsi2_start() and rcsi2_stop().
As the error recovery in rcsi2_irq_thread() relies on rcsi2_start() and
rcsi2_stop(), we need to modify rcsi2_irq_thread() accordingly.
On Gen3, a side effect of this change is that if the sink side devices
call .enable_streams() on rcar-csi2 multiple times, the second call will
fail. This is because we always use stream ID 0, so the second call
would attempt to enable the same stream again, leading to an error. In
other words, a normal single-stream setup continues to work, but trying
to use the current driver's custom VC based routing will fail.
On Gen4, this doesn't matter as the rcar-isp behaves in a similar way as
described above, and thus rcar-csi2 will only get a single
.enable_streams() call.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
---
drivers/media/platform/renesas/rcar-csi2.c | 59 ++++++++++++++++++++++++------
1 file changed, 47 insertions(+), 12 deletions(-)
diff --git a/drivers/media/platform/renesas/rcar-csi2.c b/drivers/media/platform/renesas/rcar-csi2.c
index 6635f5782175..1c8150af734f 100644
--- a/drivers/media/platform/renesas/rcar-csi2.c
+++ b/drivers/media/platform/renesas/rcar-csi2.c
@@ -1822,20 +1822,12 @@ static int rcsi2_start(struct rcar_csi2 *priv, struct v4l2_subdev_state *state)
return ret;
}
- ret = v4l2_subdev_enable_streams(priv->remote, priv->remote_pad,
- BIT_ULL(0));
- if (ret) {
- rcsi2_enter_standby(priv);
- return ret;
- }
-
return 0;
}
static void rcsi2_stop(struct rcar_csi2 *priv)
{
rcsi2_enter_standby(priv);
- v4l2_subdev_disable_streams(priv->remote, priv->remote_pad, BIT_ULL(0));
}
static int rcsi2_enable_streams(struct v4l2_subdev *sd,
@@ -1857,6 +1849,14 @@ static int rcsi2_enable_streams(struct v4l2_subdev *sd,
return ret;
}
+ ret = v4l2_subdev_enable_streams(priv->remote, priv->remote_pad,
+ BIT_ULL(0));
+ if (ret) {
+ if (priv->stream_count == 0)
+ rcsi2_stop(priv);
+ return ret;
+ }
+
priv->stream_count += 1;
return ret;
@@ -1867,7 +1867,7 @@ static int rcsi2_disable_streams(struct v4l2_subdev *sd,
u32 source_pad, u64 source_streams_mask)
{
struct rcar_csi2 *priv = sd_to_csi2(sd);
- int ret = 0;
+ int ret;
if (source_streams_mask != 1)
return -EINVAL;
@@ -1878,9 +1878,14 @@ static int rcsi2_disable_streams(struct v4l2_subdev *sd,
if (priv->stream_count == 1)
rcsi2_stop(priv);
+ ret = v4l2_subdev_disable_streams(priv->remote, priv->remote_pad,
+ BIT_ULL(0));
+ if (ret)
+ return ret;
+
priv->stream_count -= 1;
- return ret;
+ return 0;
}
static int rcsi2_set_pad_format(struct v4l2_subdev *sd,
@@ -1971,14 +1976,44 @@ static irqreturn_t rcsi2_irq_thread(int irq, void *data)
{
struct v4l2_subdev_state *state;
struct rcar_csi2 *priv = data;
+ int ret;
state = v4l2_subdev_lock_and_get_active_state(&priv->subdev);
+ if (priv->stream_count == 0)
+ goto out;
+
rcsi2_stop(priv);
+
+ ret = v4l2_subdev_disable_streams(priv->remote, priv->remote_pad,
+ BIT_ULL(0));
+ if (ret) {
+ dev_warn(priv->dev,
+ "Error recovery: failed to disable streams: %d\n",
+ ret);
+ goto out;
+ }
+
usleep_range(1000, 2000);
- if (rcsi2_start(priv, state))
- dev_warn(priv->dev, "Failed to restart CSI-2 receiver\n");
+ ret = rcsi2_start(priv, state);
+ if (ret) {
+ dev_warn(priv->dev,
+ "Error recovery: failed to start CSI-2 receiver: %d\n",
+ ret);
+ goto out;
+ }
+
+ ret = v4l2_subdev_enable_streams(priv->remote, priv->remote_pad,
+ BIT_ULL(0));
+ if (ret) {
+ dev_warn(priv->dev,
+ "Error recovery: failed to start streams: %d\n",
+ ret);
+ goto out;
+ }
+
+out:
v4l2_subdev_unlock_state(state);
return IRQ_HANDLED;
--
2.43.0
next prev parent reply other threads:[~2026-09-08 6:33 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-08 6:33 [PATCH v7 00/11] media: rcar: Streams support Tomi Valkeinen
2026-09-08 6:33 ` [PATCH v7 01/11] media: rcar-vin: Fix comment related to stride handling Tomi Valkeinen
2026-09-08 6:33 ` [PATCH v7 02/11] media: rcar-vin: Link VINs on Gen3 to a single channel on each CSI-2 Tomi Valkeinen
2026-09-08 6:33 ` [PATCH v7 03/11] media: rcar-isp: Move {enable|disable}_streams() calls Tomi Valkeinen
2026-09-08 6:33 ` Tomi Valkeinen [this message]
2026-09-08 6:33 ` [PATCH v7 05/11] media: rcar-csi2: Switch to Streams API Tomi Valkeinen
2026-09-08 6:33 ` [PATCH v7 06/11] media: rcar-isp: " Tomi Valkeinen
2026-09-08 6:33 ` [PATCH v7 07/11] media: rcar-csi2: Add .get_frame_desc op Tomi Valkeinen
2026-09-08 6:33 ` [PATCH v7 08/11] media: rcar-isp: Call get_frame_desc to find out VC & DT Tomi Valkeinen
2026-09-08 6:33 ` [PATCH v7 09/11] media: rcar-csi2: Call get_frame_desc to find out VC & DT (Gen3) Tomi Valkeinen
2026-09-08 6:33 ` [PATCH v7 10/11] media: rcar-csi2: Add full streams support Tomi Valkeinen
2026-09-08 6:33 ` [PATCH v7 11/11] media: rcar-isp: " Tomi Valkeinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260908-rcar-streams-v7-4-c406a2c2930f@ideasonboard.com \
--to=tomi.valkeinen+renesas@ideasonboard.com \
--cc=jacopo.mondi@ideasonboard.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=mchehab+huawei@kernel.org \
--cc=mchehab@kernel.org \
--cc=niklas.soderlund+renesas@ragnatech.se \
--cc=niklas.soderlund@ragnatech.se \
--cc=sakari.ailus@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox