Re: [PATCH v2 1/4] dt-bindings: media: i2c: Add bindings for Maxim Integrated MAX9286

[Laurent Pinchart <laurent.pinchart@ideasonboard.com>]

Hi Kieran,

Thank you for the patch.

On Wednesday, 8 August 2018 19:55:56 EEST Kieran Bingham wrote:
> From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> 
> The MAX9286 deserializes video data received on up to 4 Gigabit
> Multimedia Serial Links (GMSL) and outputs them on a CSI-2 port using up
> to 4 data lanes.
> 
> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
> ---
>  .../bindings/media/i2c/maxim,max9286.txt      | 180 ++++++++++++++++++
>  1 file changed, 180 insertions(+)
>  create mode 100644
> Documentation/devicetree/bindings/media/i2c/maxim,max9286.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.txt
> b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.txt new file
> mode 100644
> index 000000000000..8c099bf2939f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.txt
> @@ -0,0 +1,180 @@
> +Maxim Integrated Quad GMSL Deserializer
> +---------------------------------------
> +
> +The MAX9286 deserializes receives video data on up to 4 Gigabit Multimedia

s/deserializes/deserializer/

> +Serial Links (GMSL) and outputs them on a CSI-2 port using up to 4 data
> lanes.
> +
> +In addition to video data, the GMSL links carry a bidirectional control
> +channel that encapsulates I2C messages. The MAX9286 forwards all I2C
> traffic +not addressed to itself to the other side of the links, where a
> GMSL +serializer will output it on a local I2C bus. In the other direction
> all I2C +traffic received over GMSL by the MAX9286 is output on the local
> I2C bus.
> +
> +Required Properties:
> +
> +- compatible: Shall be "maxim,max9286"
> +- reg: I2C device address
> +
> +Optional Properties:
> +
> +- poc-supply: Regulator providing Power over Coax to the cameras
> +- pwdn-gpios: GPIO connected to the #PWDN pin
> +
> +Required endpoint nodes:
> +-----------------------
> +
> +The connections to the MAX9286 GMSL and its endpoint nodes are modeled
> using +the OF graph bindings in accordance with the video interface
> bindings defined +in
> Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +The following table lists the port number corresponding to each device
> port.
> +
> +        Port            Description
> +        ----------------------------------------
> +        Port 0          GMSL Input 0
> +        Port 1          GMSL Input 1
> +        Port 2          GMSL Input 2
> +        Port 3          GMSL Input 3
> +        Port 4          CSI-2 Output
> +
> +Optional Endpoint Properties for GSML Input Ports (Port [0-3]):
> +
> +- remote-endpoint: phandle to the remote GMSL source endpoint subnode in
> the
> +  remote node port.
> +
> +Required Endpoint Properties for CSI-2 Output Port (Port 4):
> +
> +- data-lanes: array of physical CSI-2 data lane indexes.
> +- clock-lanes: index of CSI-2 clock lane.
> +
> +Required i2c-mux nodes:
> +----------------------
> +
> +Each remote GMSL endpoint is modeled as child busses of an i2c bus

It's not the GMSL endpoint that is modeled as a child bus, it's the GMSL link. 
You should then document that the serializer device on the remote end of the 
link shall be modeled as a child node of the corresponding I2C bus. Feel free 
to come up with a better wording.

> +multiplexer/switch, in accordance with bindings described in
> +Documentation/devicetree/bindings/i2c/i2c-mux.txt.
> +
> +Required i2c child bus properties:
> +- all properties described as required i2c child bus nodes properties in
> +  Documentation/devicetree/bindings/i2c/i2c-mux.txt.
> +
> +Example:
> +-------
> +
> +	gmsl-deserializer@2c {
> +		compatible = "maxim,max9286";
> +		reg = <0x2c>;
> +		poc-supply = <&camera_poc_12v>;
> +		pwdn-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				max9286_in0: endpoint {
> +					remote-endpoint = <&rdacm20_out0>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				max9286_in1: endpoint {
> +					remote-endpoint = <&rdacm20_out1>;
> +				};
> +			};
> +
> +			port@2 {
> +				reg = <2>;
> +				max9286_in2: endpoint {
> +					remote-endpoint = <&rdacm20_out2>;
> +				};
> +			};
> +
> +			port@3 {
> +				reg = <3>;
> +				max9286_in3: endpoint {
> +					remote-endpoint = <&rdacm20_out3>;
> +				};
> +			};
> +
> +			port@4 {
> +				reg = <4>;
> +				max9286_out: endpoint {
> +					clock-lanes = <0>;
> +					data-lanes = <1 2 3 4>;
> +					remote-endpoint = <&csi40_in>;
> +				};
> +			};
> +		};
> +
> +		i2c@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0>;
> +
> +			camera@51 {
> +				compatible = "imi,rdacm20";
> +				reg = <0x51 0x61>;
> +
> +				port {
> +					rdacm20_out0: endpoint {
> +						remote-endpoint = <&max9286_in0>;
> +					};
> +				};
> +
> +			};
> +		};
> +
> +		i2c@1 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <1>;
> +
> +			camera@52 {
> +				compatible = "imi,rdacm20";
> +				reg = <0x52 0x62>;
> +				port {
> +					rdacm20_out1: endpoint {
> +						remote-endpoint = <&max9286_in1>;
> +					};
> +				};
> +			};
> +		};
> +
> +		i2c@2 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <2>;
> +
> +			camera@53 {
> +				compatible = "imi,rdacm20";
> +				reg = <0x53 0x63>;
> +				port {
> +					rdacm20_out2: endpoint {
> +						remote-endpoint = <&max9286_in2>;
> +					};
> +				};
> +			};
> +		};
> +
> +		i2c@3 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <3>;
> +
> +			camera@54 {
> +				compatible = "imi,rdacm20";
> +				reg = <0x54 0x64>;
> +				port {
> +					rdacm20_out3: endpoint {
> +						remote-endpoint = <&max9286_in3>;
> +					};
> +				};
> +			};
> +		};
> +	};

-- 
Regards,

Laurent Pinchart