public inbox for linux-media@vger.kernel.org
 help / color / mirror / Atom feed
* Help needed to add support for the card Compro VideoMate X50 (CX88/XC2028)
@ 2008-08-17  1:54 Carlos Limarino
  2008-08-17 17:20 ` Carlos Limarino
  0 siblings, 1 reply; 2+ messages in thread
From: Carlos Limarino @ 2008-08-17  1:54 UTC (permalink / raw)
  To: video4linux-list

Hi, 

I'm trying to add support for a CX23880 based card that uses the Xceive 2028 tuner. Support for this tuner was recently added to the kernel, I tried using similar cards already supported by the driver. The results were:

using card=62 (PowerColor RA330)

cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
cx88[0]: subsystem: 185b:e000, board: PowerColor RA330 [card=62,insmod option]
cx88[0]: TV tuner type 71, Radio tuner type 0
tuner' 2-0061: chip found @ 0xc2 (cx88[0])
xc2028 2-0061: creating new instance
xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
cx88[0]: Asking xc2028/3028 to load firmware xc3028-v27.fw
cx88 IR (PowerColor RA330): unknown key: key=0x3f raw=0x3f down=1
cx88 IR (PowerColor RA330): unknown key: key=0x3f raw=0x3f down=0
input: cx88 IR (PowerColor RA330) as /devices/pci0000:00/0000:00:10.0/0000:02:09.0/input/input6
cx88[0]/0: found at 0000:02:09.0, rev: 5, irq: 17, latency: 32, mmio: 0xfc000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
firmware: requesting xc3028-v27.fw
xc2028 2-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE (1), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: i2c output error: rc = -121 (should be 64)
xc2028 2-0061: -121 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE (1), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: i2c output error: rc = -121 (should be 64)
xc2028 2-0061: -121 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE FM (401), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=FM (400), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback

using card=61 (Winfast TV2000 XP Global)

cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
cx88[0]: subsystem: 185b:e000, board: Winfast TV2000 XP Global [card=61,insmod option]
cx88[0]: TV tuner type 71, Radio tuner type 0
tuner' 2-0061: chip found @ 0xc2 (cx88[0])
xc2028 2-0061: creating new instance
xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
cx88[0]: Asking xc2028/3028 to load firmware xc3028-v27.fw
cx88[0]/0: found at 0000:02:09.0, rev: 5, irq: 17, latency: 32, mmio: 0xfc000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
firmware: requesting xc3028-v27.fw
xc2028 2-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE FM (401), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE FM (401), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware

Developers of the CX18 driver found a similar problem with some cards, it seems that the pin that is used to reset the tuner changes from card to card:

http://www.gossamer-threads.com/lists/ivtv/devel/38594

Since I don't have much knowledge about driver programming, I can't find something similar to 'xceive_pin' to change & test. I would greatly appreciate any help with this.

Thank you!



      Yahoo! Cocina
Recetas prácticas y comida saludable
http://ar.mujer.yahoo.com/cocina/

--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, other threads:[~2008-08-17 17:21 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-08-17  1:54 Help needed to add support for the card Compro VideoMate X50 (CX88/XC2028) Carlos Limarino
2008-08-17 17:20 ` Carlos Limarino

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox