From: Carlos Limarino <climarino@yahoo.com.ar>
To: video4linux-list@redhat.com
Subject: Help needed to add support for the card Compro VideoMate X50 (CX88/XC2028)
Date: Sat, 16 Aug 2008 18:54:17 -0700 (PDT) [thread overview]
Message-ID: <474079.21637.qm@web34503.mail.mud.yahoo.com> (raw)
Hi,
I'm trying to add support for a CX23880 based card that uses the Xceive 2028 tuner. Support for this tuner was recently added to the kernel, I tried using similar cards already supported by the driver. The results were:
using card=62 (PowerColor RA330)
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
cx88[0]: subsystem: 185b:e000, board: PowerColor RA330 [card=62,insmod option]
cx88[0]: TV tuner type 71, Radio tuner type 0
tuner' 2-0061: chip found @ 0xc2 (cx88[0])
xc2028 2-0061: creating new instance
xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
cx88[0]: Asking xc2028/3028 to load firmware xc3028-v27.fw
cx88 IR (PowerColor RA330): unknown key: key=0x3f raw=0x3f down=1
cx88 IR (PowerColor RA330): unknown key: key=0x3f raw=0x3f down=0
input: cx88 IR (PowerColor RA330) as /devices/pci0000:00/0000:00:10.0/0000:02:09.0/input/input6
cx88[0]/0: found at 0000:02:09.0, rev: 5, irq: 17, latency: 32, mmio: 0xfc000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
firmware: requesting xc3028-v27.fw
xc2028 2-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE (1), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: i2c output error: rc = -121 (should be 64)
xc2028 2-0061: -121 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE (1), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: i2c output error: rc = -121 (should be 64)
xc2028 2-0061: -121 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE FM (401), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=FM (400), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
using card=61 (Winfast TV2000 XP Global)
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
cx88[0]: subsystem: 185b:e000, board: Winfast TV2000 XP Global [card=61,insmod option]
cx88[0]: TV tuner type 71, Radio tuner type 0
tuner' 2-0061: chip found @ 0xc2 (cx88[0])
xc2028 2-0061: creating new instance
xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
cx88[0]: Asking xc2028/3028 to load firmware xc3028-v27.fw
cx88[0]/0: found at 0000:02:09.0, rev: 5, irq: 17, latency: 32, mmio: 0xfc000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
firmware: requesting xc3028-v27.fw
xc2028 2-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE FM (401), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware
cx88[0]: Calling XC2028/3028 callback
xc2028 2-0061: Loading firmware for type=BASE FM (401), id 0000000000000000.
cx88[0]: Calling XC2028/3028 callback
i2c-adapter i2c-2: sendbytes: NAK bailout.
xc2028 2-0061: i2c output error: rc = -5 (should be 64)
xc2028 2-0061: -5 returned from send
xc2028 2-0061: Error -22 while loading base firmware
Developers of the CX18 driver found a similar problem with some cards, it seems that the pin that is used to reset the tuner changes from card to card:
http://www.gossamer-threads.com/lists/ivtv/devel/38594
Since I don't have much knowledge about driver programming, I can't find something similar to 'xceive_pin' to change & test. I would greatly appreciate any help with this.
Thank you!
Yahoo! Cocina
Recetas prácticas y comida saludable
http://ar.mujer.yahoo.com/cocina/
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
next reply other threads:[~2008-08-17 1:55 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-08-17 1:54 Carlos Limarino [this message]
2008-08-17 17:20 ` Help needed to add support for the card Compro VideoMate X50 (CX88/XC2028) Carlos Limarino
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=474079.21637.qm@web34503.mail.mud.yahoo.com \
--to=climarino@yahoo.com.ar \
--cc=video4linux-list@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox