* Re: [linux-dvb] Yuan EC372S (STK7700D based device)
[not found] <ea4209750801161224p6b75d7fanbdcd29e7d367802d@mail.gmail.com>
@ 2008-02-18 18:57 ` Antti Palosaari
2008-02-18 21:06 ` Albert Comerma
0 siblings, 1 reply; 10+ messages in thread
From: Antti Palosaari @ 2008-02-18 18:57 UTC (permalink / raw)
To: Albert Comerma; +Cc: linux-dvb
moikka
I have also this device (express card). I haven't looked inside yet, but
I think there is DibCOM STK7700D (in my understanding dual demod chip)
and only *one* MT2266 tuner. I tried various GPIO settings but no luck yet.
GPIO6 is for MT2266.
GPIO9 and GPIO10 are for frontend.
Looks like tuner goes to correct frequency because I got always
PID-filter timeouts when tuning to correct freq. I will now try to take
some usb-sniffs to see configuration used. Any help is welcome.
regards
Antti
Albert Comerma wrote:
> Hi!, with Michel (mm-sl@ibelgique.com <mailto:mm-sl@ibelgique.com>) who
> is a owner of this Yuan card we added the device to dib0700_devices, and
> we got it recognized without problems. The only problem is that no
> channel is detected on scan on kaffeine or other software... I post some
> dmesg. We don't know where it may be the problem... or how to detect it...
>
> usb 4-2: new high speed USB device using ehci_hcd and address 6
> usb 4-2: new device found, idVendor=1164, idProduct=1edc
> usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=3
> usb 4-2: Product: STK7700D
> usb 4-2: Manufacturer: YUANRD
> usb 4-2: SerialNumber: 0000000001
> usb 4-2: configuration #1 chosen from 1 choice
> dvb-usb: found a 'Yuan EC372S' in cold state, will try to load a firmware
> dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
> dib0700: firmware started successfully.
> dvb-usb: found a 'Yuan EC372S' in warm state.
> dvb-usb: will pass the complete MPEG2 transport stream to the software
> demuxer.
> DVB: registering new adapter (Yuan EC372S)
> dvb-usb: no frontend was attached by 'Yuan EC372S'
> dvb-usb: will pass the complete MPEG2 transport stream to the software
> demuxer.
> DVB: registering new adapter (Yuan EC372S)
> DVB: registering frontend 1 (DiBcom 7000PC)...
> MT2266: successfully identified
> input: IR-receiver inside an USB DVB receiver as /class/input/input10
> dvb-usb: schedule remote query interval to 150 msecs.
> dvb-usb: Yuan EC372S successfully initialized and connected.
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
--
http://palosaari.fi/
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [linux-dvb] Yuan EC372S (STK7700D based device)
2008-02-18 18:57 ` [linux-dvb] Yuan EC372S (STK7700D based device) Antti Palosaari
@ 2008-02-18 21:06 ` Albert Comerma
2008-02-18 22:05 ` Antti Palosaari
0 siblings, 1 reply; 10+ messages in thread
From: Albert Comerma @ 2008-02-18 21:06 UTC (permalink / raw)
To: Antti Palosaari; +Cc: linux-dvb
[-- Attachment #1.1: Type: text/plain, Size: 2706 bytes --]
Hey people, we already solved this problems. I submitted a patch a few days
ago, but I think it's not on the current sources. I send again the patch.
Basically it must use the same frontend description as asus cards.
Albert
2008/2/18, Antti Palosaari <crope@iki.fi>:
>
> moikka
> I have also this device (express card). I haven't looked inside yet, but
> I think there is DibCOM STK7700D (in my understanding dual demod chip)
> and only *one* MT2266 tuner. I tried various GPIO settings but no luck
> yet.
> GPIO6 is for MT2266.
> GPIO9 and GPIO10 are for frontend.
>
> Looks like tuner goes to correct frequency because I got always
> PID-filter timeouts when tuning to correct freq. I will now try to take
> some usb-sniffs to see configuration used. Any help is welcome.
>
> regards
> Antti
>
> Albert Comerma wrote:
> > Hi!, with Michel (mm-sl@ibelgique.com <mailto:mm-sl@ibelgique.com>) who
>
> > is a owner of this Yuan card we added the device to dib0700_devices, and
> > we got it recognized without problems. The only problem is that no
> > channel is detected on scan on kaffeine or other software... I post some
> > dmesg. We don't know where it may be the problem... or how to detect
> it...
> >
> > usb 4-2: new high speed USB device using ehci_hcd and address 6
> > usb 4-2: new device found, idVendor=1164, idProduct=1edc
> > usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=3
> > usb 4-2: Product: STK7700D
> > usb 4-2: Manufacturer: YUANRD
> > usb 4-2: SerialNumber: 0000000001
> > usb 4-2: configuration #1 chosen from 1 choice
> > dvb-usb: found a 'Yuan EC372S' in cold state, will try to load a
> firmware
> > dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
> > dib0700: firmware started successfully.
> > dvb-usb: found a 'Yuan EC372S' in warm state.
> > dvb-usb: will pass the complete MPEG2 transport stream to the software
> > demuxer.
> > DVB: registering new adapter (Yuan EC372S)
> > dvb-usb: no frontend was attached by 'Yuan EC372S'
> > dvb-usb: will pass the complete MPEG2 transport stream to the software
> > demuxer.
> > DVB: registering new adapter (Yuan EC372S)
> > DVB: registering frontend 1 (DiBcom 7000PC)...
> > MT2266: successfully identified
> > input: IR-receiver inside an USB DVB receiver as /class/input/input10
> > dvb-usb: schedule remote query interval to 150 msecs.
> > dvb-usb: Yuan EC372S successfully initialized and connected.
> >
> >
>
> > ------------------------------------------------------------------------
> >
> > _______________________________________________
> > linux-dvb mailing list
> > linux-dvb@linuxtv.org
> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>
>
> --
> http://palosaari.fi/
>
[-- Attachment #1.2: Type: text/html, Size: 3468 bytes --]
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #2: YuanEC372.patch --]
[-- Type: text/x-patch; name=YuanEC372.patch, Size: 2912 bytes --]
diff -crB v4l-dvb-7d8558f3fc66-orig/linux/drivers/media/dvb/dvb-usb/dib0700_devices.c v4l-dvb-7d8558f3fc66/linux/drivers/media/dvb/dvb-usb/dib0700_devices.c
*** v4l-dvb-7d8558f3fc66-orig/linux/drivers/media/dvb/dvb-usb/dib0700_devices.c 2008-01-27 16:23:53.000000000 +0100
--- v4l-dvb-7d8558f3fc66/linux/drivers/media/dvb/dvb-usb/dib0700_devices.c 2008-01-27 16:34:20.000000000 +0100
***************
*** 905,910 ****
--- 905,911 ----
{ USB_DEVICE(USB_VID_ASUS, USB_PID_ASUS_U3100) },
/* 25 */ { USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_STICK_3) },
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_MYTV_T) },
+ { USB_DEVICE(USB_VID_YUAN, USB_PID_YUAN_EC372S) },
{ 0 } /* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, dib0700_usb_id_table);
***************
*** 1069,1080 ****
},
},
! .num_device_descs = 1,
.devices = {
{ "ASUS My Cinema U3000 Mini DVBT Tuner",
{ &dib0700_usb_id_table[23], NULL },
{ NULL },
},
}
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
--- 1070,1085 ----
},
},
! .num_device_descs = 2,
.devices = {
{ "ASUS My Cinema U3000 Mini DVBT Tuner",
{ &dib0700_usb_id_table[23], NULL },
{ NULL },
},
+ { "Yuan EC372S",
+ { &dib0700_usb_id_table[27], NULL },
+ { NULL },
+ }
}
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
diff -crB v4l-dvb-7d8558f3fc66-orig/linux/drivers/media/dvb/dvb-usb/dvb-usb-ids.h v4l-dvb-7d8558f3fc66/linux/drivers/media/dvb/dvb-usb/dvb-usb-ids.h
*** v4l-dvb-7d8558f3fc66-orig/linux/drivers/media/dvb/dvb-usb/dvb-usb-ids.h 2008-01-27 16:23:53.000000000 +0100
--- v4l-dvb-7d8558f3fc66/linux/drivers/media/dvb/dvb-usb/dvb-usb-ids.h 2008-01-27 16:27:20.000000000 +0100
***************
*** 46,53 ****
#define USB_VID_ULTIMA_ELECTRONIC 0x05d8
#define USB_VID_UNIWILL 0x1584
#define USB_VID_WIDEVIEW 0x14aa
- /* dom : pour gigabyte u7000 */
#define USB_VID_GIGABYTE 0x1044
/* Product IDs */
--- 46,53 ----
#define USB_VID_ULTIMA_ELECTRONIC 0x05d8
#define USB_VID_UNIWILL 0x1584
#define USB_VID_WIDEVIEW 0x14aa
#define USB_VID_GIGABYTE 0x1044
+ #define USB_VID_YUAN 0x1164
/* Product IDs */
***************
*** 183,191 ****
#define USB_PID_OPERA1_WARM 0x3829
#define USB_PID_LIFEVIEW_TV_WALKER_TWIN_COLD 0x0514
#define USB_PID_LIFEVIEW_TV_WALKER_TWIN_WARM 0x0513
- /* dom pour gigabyte u7000 */
#define USB_PID_GIGABYTE_U7000 0x7001
#define USB_PID_ASUS_U3000 0x171f
#define USB_PID_ASUS_U3100 0x173f
#endif
--- 183,191 ----
#define USB_PID_OPERA1_WARM 0x3829
#define USB_PID_LIFEVIEW_TV_WALKER_TWIN_COLD 0x0514
#define USB_PID_LIFEVIEW_TV_WALKER_TWIN_WARM 0x0513
#define USB_PID_GIGABYTE_U7000 0x7001
#define USB_PID_ASUS_U3000 0x171f
#define USB_PID_ASUS_U3100 0x173f
+ #define USB_PID_YUAN_EC372S 0x1edc
#endif
[-- Attachment #3: Type: text/plain, Size: 150 bytes --]
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [linux-dvb] Yuan EC372S (STK7700D based device)
2008-02-18 21:06 ` Albert Comerma
@ 2008-02-18 22:05 ` Antti Palosaari
2008-02-18 22:24 ` Albert Comerma
0 siblings, 1 reply; 10+ messages in thread
From: Antti Palosaari @ 2008-02-18 22:05 UTC (permalink / raw)
To: Albert Comerma; +Cc: linux-dvb
[-- Attachment #1: Type: text/plain, Size: 3838 bytes --]
moi
It does not work for me. It says same PID-filter timeout as I have got
earlier. I don't have amplified antenna now, but I can say that all
other DVB-T sticks I have are working with this small antenna. It could
be that sensitivity of this hardware is bad or there is something wrong
with driver or firmware. Lets try to test it Windows to see if it is
working or not.
Logs attached.
regards
Antti
Albert Comerma wrote:
> Hey people, we already solved this problems. I submitted a patch a few
> days ago, but I think it's not on the current sources. I send again the
> patch. Basically it must use the same frontend description as asus cards.
>
> Albert
>
> 2008/2/18, Antti Palosaari <crope@iki.fi <mailto:crope@iki.fi>>:
>
> moikka
> I have also this device (express card). I haven't looked inside yet, but
> I think there is DibCOM STK7700D (in my understanding dual demod chip)
> and only *one* MT2266 tuner. I tried various GPIO settings but no
> luck yet.
> GPIO6 is for MT2266.
> GPIO9 and GPIO10 are for frontend.
>
> Looks like tuner goes to correct frequency because I got always
> PID-filter timeouts when tuning to correct freq. I will now try to take
> some usb-sniffs to see configuration used. Any help is welcome.
>
> regards
> Antti
>
> Albert Comerma wrote:
> > Hi!, with Michel (mm-sl@ibelgique.com
> <mailto:mm-sl@ibelgique.com> <mailto:mm-sl@ibelgique.com
> <mailto:mm-sl@ibelgique.com>>) who
>
> > is a owner of this Yuan card we added the device to
> dib0700_devices, and
> > we got it recognized without problems. The only problem is that no
> > channel is detected on scan on kaffeine or other software... I
> post some
> > dmesg. We don't know where it may be the problem... or how to
> detect it...
> >
> > usb 4-2: new high speed USB device using ehci_hcd and address 6
> > usb 4-2: new device found, idVendor=1164, idProduct=1edc
> > usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=3
> > usb 4-2: Product: STK7700D
> > usb 4-2: Manufacturer: YUANRD
> > usb 4-2: SerialNumber: 0000000001
> > usb 4-2: configuration #1 chosen from 1 choice
> > dvb-usb: found a 'Yuan EC372S' in cold state, will try to load a
> firmware
> > dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
> > dib0700: firmware started successfully.
> > dvb-usb: found a 'Yuan EC372S' in warm state.
> > dvb-usb: will pass the complete MPEG2 transport stream to the
> software
> > demuxer.
> > DVB: registering new adapter (Yuan EC372S)
> > dvb-usb: no frontend was attached by 'Yuan EC372S'
> > dvb-usb: will pass the complete MPEG2 transport stream to the
> software
> > demuxer.
> > DVB: registering new adapter (Yuan EC372S)
> > DVB: registering frontend 1 (DiBcom 7000PC)...
> > MT2266: successfully identified
> > input: IR-receiver inside an USB DVB receiver as /class/input/input10
> > dvb-usb: schedule remote query interval to 150 msecs.
> > dvb-usb: Yuan EC372S successfully initialized and connected.
> >
> >
>
> >
> ------------------------------------------------------------------------
> >
> > _______________________________________________
> > linux-dvb mailing list
> > linux-dvb@linuxtv.org <mailto:linux-dvb@linuxtv.org>
> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>
>
> --
> http://palosaari.fi/
>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
--
http://palosaari.fi/
[-- Attachment #2: lsusb_Yuan_EC372S.txt --]
[-- Type: text/plain, Size: 3002 bytes --]
Bus 001 Device 005: ID 1164:1edc YUAN High-Tech Development Co., Ltd
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1164 YUAN High-Tech Development Co., Ltd
idProduct 0x1edc
bcdDevice 1.00
iManufacturer 1 YUANRD
iProduct 2 STK7700D
iSerial 3 0000000001
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 46
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
[-- Attachment #3: Yuan_EC372S.txt --]
[-- Type: text/plain, Size: 2545 bytes --]
Feb 18 23:50:53 localhost kernel: usb 1-8: USB disconnect, address 5
Feb 18 23:50:55 localhost kernel: usb 1-8: new high speed USB device using ehci_hcd and address 6
Feb 18 23:50:55 localhost kernel: usb 1-8: configuration #1 chosen from 1 choice
Feb 18 23:50:55 localhost kernel: dib0700: loaded with support for 6 different device-types
Feb 18 23:50:55 localhost kernel: dvb-usb: found a 'Yuan EC372S' in cold state, will try to load a firmware
Feb 18 23:50:55 localhost kernel: dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
Feb 18 23:50:55 localhost kernel: dib0700: firmware started successfully.
Feb 18 23:50:56 localhost kernel: dvb-usb: found a 'Yuan EC372S' in warm state.
Feb 18 23:50:56 localhost kernel: dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
Feb 18 23:50:56 localhost kernel: DVB: registering new adapter (Yuan EC372S)
Feb 18 23:50:56 localhost kernel: DVB: registering frontend 0 (DiBcom 7000PC)...
Feb 18 23:50:56 localhost kernel: MT2266: successfully identified
Feb 18 23:50:56 localhost kernel: dvb-usb: Yuan EC372S successfully initialized and connected.
Feb 18 23:50:56 localhost kernel: usbcore: registered new interface driver dvb_usb_dib0700
[crope@localhost linuxtv]$ scandvb fi-Oulu
scanning fi-Oulu
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
initial transponder 634000000 0 2 9 3 1 2 0
initial transponder 714000000 0 2 9 3 1 2 0
initial transponder 738000000 0 2 9 3 1 2 0
initial transponder 602000000 0 2 9 3 1 2 0
>>> tune to: 634000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010
>>> tune to: 714000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010
>>> tune to: 738000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010
>>> tune to: 602000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010
dumping lists (0 services)
Done.
[crope@localhost linuxtv]$
[-- Attachment #4: Type: text/plain, Size: 150 bytes --]
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [linux-dvb] Yuan EC372S (STK7700D based device)
2008-02-18 22:05 ` Antti Palosaari
@ 2008-02-18 22:24 ` Albert Comerma
2008-02-18 22:53 ` Antti Palosaari
0 siblings, 1 reply; 10+ messages in thread
From: Albert Comerma @ 2008-02-18 22:24 UTC (permalink / raw)
To: Antti Palosaari; +Cc: linux-dvb
[-- Attachment #1.1: Type: text/plain, Size: 10110 bytes --]
Uhm... that's strange, I don't have any of this cards to test, but other
people reported that this solution was working. Could you post the
dib0700_devices.c you're using to have a look?
Albert
2008/2/18, Antti Palosaari <crope@iki.fi>:
>
> moi
> It does not work for me. It says same PID-filter timeout as I have got
> earlier. I don't have amplified antenna now, but I can say that all
> other DVB-T sticks I have are working with this small antenna. It could
> be that sensitivity of this hardware is bad or there is something wrong
> with driver or firmware. Lets try to test it Windows to see if it is
> working or not.
> Logs attached.
>
>
> regards
> Antti
>
> Albert Comerma wrote:
>
> > Hey people, we already solved this problems. I submitted a patch a few
> > days ago, but I think it's not on the current sources. I send again the
> > patch. Basically it must use the same frontend description as asus
> cards.
> >
> > Albert
> >
>
> > 2008/2/18, Antti Palosaari <crope@iki.fi <mailto:crope@iki.fi>>:
>
> >
> > moikka
> > I have also this device (express card). I haven't looked inside yet,
> but
> > I think there is DibCOM STK7700D (in my understanding dual demod
> chip)
> > and only *one* MT2266 tuner. I tried various GPIO settings but no
> > luck yet.
> > GPIO6 is for MT2266.
> > GPIO9 and GPIO10 are for frontend.
> >
> > Looks like tuner goes to correct frequency because I got always
> > PID-filter timeouts when tuning to correct freq. I will now try to
> take
> > some usb-sniffs to see configuration used. Any help is welcome.
> >
> > regards
> > Antti
> >
> > Albert Comerma wrote:
> > > Hi!, with Michel (mm-sl@ibelgique.com
>
> > <mailto:mm-sl@ibelgique.com> <mailto:mm-sl@ibelgique.com
>
> > <mailto:mm-sl@ibelgique.com>>) who
> >
> > > is a owner of this Yuan card we added the device to
> > dib0700_devices, and
> > > we got it recognized without problems. The only problem is that
> no
> > > channel is detected on scan on kaffeine or other software... I
> > post some
> > > dmesg. We don't know where it may be the problem... or how to
> > detect it...
> > >
> > > usb 4-2: new high speed USB device using ehci_hcd and address 6
> > > usb 4-2: new device found, idVendor=1164, idProduct=1edc
> > > usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=3
> > > usb 4-2: Product: STK7700D
> > > usb 4-2: Manufacturer: YUANRD
> > > usb 4-2: SerialNumber: 0000000001
> > > usb 4-2: configuration #1 chosen from 1 choice
> > > dvb-usb: found a 'Yuan EC372S' in cold state, will try to load a
> > firmware
> > > dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
> > > dib0700: firmware started successfully.
> > > dvb-usb: found a 'Yuan EC372S' in warm state.
> > > dvb-usb: will pass the complete MPEG2 transport stream to the
> > software
> > > demuxer.
> > > DVB: registering new adapter (Yuan EC372S)
> > > dvb-usb: no frontend was attached by 'Yuan EC372S'
> > > dvb-usb: will pass the complete MPEG2 transport stream to the
> > software
> > > demuxer.
> > > DVB: registering new adapter (Yuan EC372S)
> > > DVB: registering frontend 1 (DiBcom 7000PC)...
> > > MT2266: successfully identified
> > > input: IR-receiver inside an USB DVB receiver as
> /class/input/input10
> > > dvb-usb: schedule remote query interval to 150 msecs.
> > > dvb-usb: Yuan EC372S successfully initialized and connected.
> > >
> > >
> >
> > >
> >
> ------------------------------------------------------------------------
> > >
> > > _______________________________________________
> > > linux-dvb mailing list
>
> > > linux-dvb@linuxtv.org <mailto:linux-dvb@linuxtv.org>
>
> > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> >
> >
> >
> > --
> > http://palosaari.fi/
> >
> >
> >
> > ------------------------------------------------------------------------
> >
> > _______________________________________________
> > linux-dvb mailing list
> > linux-dvb@linuxtv.org
> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>
> --
> http://palosaari.fi/
>
>
> Bus 001 Device 005: ID 1164:1edc YUAN High-Tech Development Co., Ltd
> Device Descriptor:
> bLength 18
> bDescriptorType 1
> bcdUSB 2.00
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 64
> idVendor 0x1164 YUAN High-Tech Development Co., Ltd
> idProduct 0x1edc
> bcdDevice 1.00
> iManufacturer 1 YUANRD
> iProduct 2 STK7700D
> iSerial 3 0000000001
> bNumConfigurations 1
> Configuration Descriptor:
> bLength 9
> bDescriptorType 2
> wTotalLength 46
> bNumInterfaces 1
> bConfigurationValue 1
> iConfiguration 0
> bmAttributes 0xa0
> Remote Wakeup
> MaxPower 500mA
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 0
> bAlternateSetting 0
> bNumEndpoints 4
> bInterfaceClass 255 Vendor Specific Class
> bInterfaceSubClass 0
> bInterfaceProtocol 0
> iInterface 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x01 EP 1 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x81 EP 1 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x82 EP 2 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x83 EP 3 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Device Qualifier (for other device speed):
> bLength 10
> bDescriptorType 6
> bcdUSB 2.00
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 64
> bNumConfigurations 1
>
> Feb 18 23:50:53 localhost kernel: usb 1-8: USB disconnect, address 5
> Feb 18 23:50:55 localhost kernel: usb 1-8: new high speed USB device using
> ehci_hcd and address 6
> Feb 18 23:50:55 localhost kernel: usb 1-8: configuration #1 chosen from 1
> choice
> Feb 18 23:50:55 localhost kernel: dib0700: loaded with support for 6
> different device-types
> Feb 18 23:50:55 localhost kernel: dvb-usb: found a 'Yuan EC372S' in cold
> state, will try to load a firmware
> Feb 18 23:50:55 localhost kernel: dvb-usb: downloading firmware from file
> 'dvb-usb-dib0700-1.10.fw'
> Feb 18 23:50:55 localhost kernel: dib0700: firmware started successfully.
> Feb 18 23:50:56 localhost kernel: dvb-usb: found a 'Yuan EC372S' in warm
> state.
> Feb 18 23:50:56 localhost kernel: dvb-usb: will pass the complete MPEG2
> transport stream to the software demuxer.
> Feb 18 23:50:56 localhost kernel: DVB: registering new adapter (Yuan
> EC372S)
> Feb 18 23:50:56 localhost kernel: DVB: registering frontend 0 (DiBcom
> 7000PC)...
> Feb 18 23:50:56 localhost kernel: MT2266: successfully identified
> Feb 18 23:50:56 localhost kernel: dvb-usb: Yuan EC372S successfully
> initialized and connected.
> Feb 18 23:50:56 localhost kernel: usbcore: registered new interface driver
> dvb_usb_dib0700
>
> [crope@localhost linuxtv]$ scandvb fi-Oulu
> scanning fi-Oulu
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> initial transponder 634000000 0 2 9 3 1 2 0
> initial transponder 714000000 0 2 9 3 1 2 0
> initial transponder 738000000 0 2 9 3 1 2 0
> initial transponder 602000000 0 2 9 3 1 2 0
> >>> tune to:
> 634000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> >>> tune to:
> 714000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> >>> tune to:
> 738000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> >>> tune to:
> 602000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> dumping lists (0 services)
> Done.
> [crope@localhost linuxtv]$
>
>
>
[-- Attachment #1.2: Type: text/html, Size: 19869 bytes --]
[-- Attachment #2: Type: text/plain, Size: 150 bytes --]
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [linux-dvb] Yuan EC372S (STK7700D based device)
2008-02-18 22:24 ` Albert Comerma
@ 2008-02-18 22:53 ` Antti Palosaari
2008-02-18 23:30 ` Albert Comerma
0 siblings, 1 reply; 10+ messages in thread
From: Antti Palosaari @ 2008-02-18 22:53 UTC (permalink / raw)
To: Albert Comerma; +Cc: linux-dvb
[-- Attachment #1: Type: text/plain, Size: 11906 bytes --]
latest v4l-master + patch you give.
regards
Antti
Albert Comerma wrote:
> Uhm... that's strange, I don't have any of this cards to test, but other
> people reported that this solution was working. Could you post the
> dib0700_devices.c you're using to have a look?
>
> Albert
>
> 2008/2/18, Antti Palosaari <crope@iki.fi <mailto:crope@iki.fi>>:
>
> moi
> It does not work for me. It says same PID-filter timeout as I have got
> earlier. I don't have amplified antenna now, but I can say that all
> other DVB-T sticks I have are working with this small antenna. It could
> be that sensitivity of this hardware is bad or there is something wrong
> with driver or firmware. Lets try to test it Windows to see if it is
> working or not.
> Logs attached.
>
>
> regards
> Antti
>
> Albert Comerma wrote:
>
> > Hey people, we already solved this problems. I submitted a patch
> a few
> > days ago, but I think it's not on the current sources. I send
> again the
> > patch. Basically it must use the same frontend description as
> asus cards.
> >
> > Albert
> >
>
> > 2008/2/18, Antti Palosaari <crope@iki.fi <mailto:crope@iki.fi>
> <mailto:crope@iki.fi <mailto:crope@iki.fi>>>:
>
> >
> > moikka
> > I have also this device (express card). I haven't looked
> inside yet, but
> > I think there is DibCOM STK7700D (in my understanding dual
> demod chip)
> > and only *one* MT2266 tuner. I tried various GPIO settings but no
> > luck yet.
> > GPIO6 is for MT2266.
> > GPIO9 and GPIO10 are for frontend.
> >
> > Looks like tuner goes to correct frequency because I got always
> > PID-filter timeouts when tuning to correct freq. I will now
> try to take
> > some usb-sniffs to see configuration used. Any help is welcome.
> >
> > regards
> > Antti
> >
> > Albert Comerma wrote:
> > > Hi!, with Michel (mm-sl@ibelgique.com
> <mailto:mm-sl@ibelgique.com>
>
> > <mailto:mm-sl@ibelgique.com <mailto:mm-sl@ibelgique.com>>
> <mailto:mm-sl@ibelgique.com <mailto:mm-sl@ibelgique.com>
>
> > <mailto:mm-sl@ibelgique.com <mailto:mm-sl@ibelgique.com>>>) who
> >
> > > is a owner of this Yuan card we added the device to
> > dib0700_devices, and
> > > we got it recognized without problems. The only problem is
> that no
> > > channel is detected on scan on kaffeine or other software... I
> > post some
> > > dmesg. We don't know where it may be the problem... or how to
> > detect it...
> > >
> > > usb 4-2: new high speed USB device using ehci_hcd and
> address 6
> > > usb 4-2: new device found, idVendor=1164, idProduct=1edc
> > > usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=3
> > > usb 4-2: Product: STK7700D
> > > usb 4-2: Manufacturer: YUANRD
> > > usb 4-2: SerialNumber: 0000000001
> > > usb 4-2: configuration #1 chosen from 1 choice
> > > dvb-usb: found a 'Yuan EC372S' in cold state, will try to
> load a
> > firmware
> > > dvb-usb: downloading firmware from file
> 'dvb-usb-dib0700-1.10.fw'
> > > dib0700: firmware started successfully.
> > > dvb-usb: found a 'Yuan EC372S' in warm state.
> > > dvb-usb: will pass the complete MPEG2 transport stream to the
> > software
> > > demuxer.
> > > DVB: registering new adapter (Yuan EC372S)
> > > dvb-usb: no frontend was attached by 'Yuan EC372S'
> > > dvb-usb: will pass the complete MPEG2 transport stream to the
> > software
> > > demuxer.
> > > DVB: registering new adapter (Yuan EC372S)
> > > DVB: registering frontend 1 (DiBcom 7000PC)...
> > > MT2266: successfully identified
> > > input: IR-receiver inside an USB DVB receiver as
> /class/input/input10
> > > dvb-usb: schedule remote query interval to 150 msecs.
> > > dvb-usb: Yuan EC372S successfully initialized and connected.
> > >
> > >
> >
> > >
> >
> ------------------------------------------------------------------------
> > >
> > > _______________________________________________
> > > linux-dvb mailing list
>
> > > linux-dvb@linuxtv.org <mailto:linux-dvb@linuxtv.org>
> <mailto:linux-dvb@linuxtv.org <mailto:linux-dvb@linuxtv.org>>
>
> > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> >
> >
> >
> > --
> > http://palosaari.fi/
> >
> >
> >
> >
> ------------------------------------------------------------------------
> >
> > _______________________________________________
> > linux-dvb mailing list
> > linux-dvb@linuxtv.org <mailto:linux-dvb@linuxtv.org>
> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>
> --
> http://palosaari.fi/
>
>
> Bus 001 Device 005: ID 1164:1edc YUAN High-Tech Development Co., Ltd
> Device Descriptor:
> bLength 18
> bDescriptorType 1
> bcdUSB 2.00
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 64
> idVendor 0x1164 YUAN High-Tech Development Co., Ltd
> idProduct 0x1edc
> bcdDevice 1.00
> iManufacturer 1 YUANRD
> iProduct 2 STK7700D
> iSerial 3 0000000001
> bNumConfigurations 1
> Configuration Descriptor:
> bLength 9
> bDescriptorType 2
> wTotalLength 46
> bNumInterfaces 1
> bConfigurationValue 1
> iConfiguration 0
> bmAttributes 0xa0
> Remote Wakeup
> MaxPower 500mA
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 0
> bAlternateSetting 0
> bNumEndpoints 4
> bInterfaceClass 255 Vendor Specific Class
> bInterfaceSubClass 0
> bInterfaceProtocol 0
> iInterface 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x01 EP 1 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x81 EP 1 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x82 EP 2 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x83 EP 3 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Device Qualifier (for other device speed):
> bLength 10
> bDescriptorType 6
> bcdUSB 2.00
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 64
> bNumConfigurations 1
>
> Feb 18 23:50:53 localhost kernel: usb 1-8: USB disconnect, address 5
> Feb 18 23:50:55 localhost kernel: usb 1-8: new high speed USB device
> using ehci_hcd and address 6
> Feb 18 23:50:55 localhost kernel: usb 1-8: configuration #1 chosen
> from 1 choice
> Feb 18 23:50:55 localhost kernel: dib0700: loaded with support for 6
> different device-types
> Feb 18 23:50:55 localhost kernel: dvb-usb: found a 'Yuan EC372S' in
> cold state, will try to load a firmware
> Feb 18 23:50:55 localhost kernel: dvb-usb: downloading firmware from
> file 'dvb-usb-dib0700-1.10.fw'
> Feb 18 23:50:55 localhost kernel: dib0700: firmware started
> successfully.
> Feb 18 23:50:56 localhost kernel: dvb-usb: found a 'Yuan EC372S' in
> warm state.
> Feb 18 23:50:56 localhost kernel: dvb-usb: will pass the complete
> MPEG2 transport stream to the software demuxer.
> Feb 18 23:50:56 localhost kernel: DVB: registering new adapter (Yuan
> EC372S)
> Feb 18 23:50:56 localhost kernel: DVB: registering frontend 0
> (DiBcom 7000PC)...
> Feb 18 23:50:56 localhost kernel: MT2266: successfully identified
> Feb 18 23:50:56 localhost kernel: dvb-usb: Yuan EC372S successfully
> initialized and connected.
> Feb 18 23:50:56 localhost kernel: usbcore: registered new interface
> driver dvb_usb_dib0700
>
> [crope@localhost linuxtv]$ scandvb fi-Oulu
> scanning fi-Oulu
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> initial transponder 634000000 0 2 9 3 1 2 0
> initial transponder 714000000 0 2 9 3 1 2 0
> initial transponder 738000000 0 2 9 3 1 2 0
> initial transponder 602000000 0 2 9 3 1 2 0
> >>> tune to:
> 634000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> >>> tune to:
> 714000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> >>> tune to:
> 738000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> >>> tune to:
> 602000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> dumping lists (0 services)
> Done.
> [crope@localhost linuxtv]$
>
>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
--
http://palosaari.fi/
[-- Attachment #2: dib0700_devices.c --]
[-- Type: text/x-csrc, Size: 33192 bytes --]
/* Linux driver for devices based on the DiBcom DiB0700 USB bridge
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the Free
* Software Foundation, version 2.
*
* Copyright (C) 2005-7 DiBcom, SA
*/
#include "dib0700.h"
#include "dib3000mc.h"
#include "dib7000m.h"
#include "dib7000p.h"
#include "mt2060.h"
#include "mt2266.h"
#include "dib0070.h"
static int force_lna_activation;
module_param(force_lna_activation, int, 0644);
MODULE_PARM_DESC(force_lna_activation, "force the activation of Low-Noise-Amplifyer(s) (LNA), "
"if applicable for the device (default: 0=automatic/off).");
struct dib0700_adapter_state {
int (*set_param_save) (struct dvb_frontend *, struct dvb_frontend_parameters *);
};
/* Hauppauge Nova-T 500 (aka Bristol)
* has a LNA on GPIO0 which is enabled by setting 1 */
static struct mt2060_config bristol_mt2060_config[2] = {
{
.i2c_address = 0x60,
.clock_out = 3,
}, {
.i2c_address = 0x61,
}
};
static struct dibx000_agc_config bristol_dib3000p_mt2060_agc_config = {
.band_caps = BAND_VHF | BAND_UHF,
.setup = (1 << 8) | (5 << 5) | (0 << 4) | (0 << 3) | (0 << 2) | (2 << 0),
.agc1_max = 42598,
.agc1_min = 17694,
.agc2_max = 45875,
.agc2_min = 0,
.agc1_pt1 = 0,
.agc1_pt2 = 59,
.agc1_slope1 = 0,
.agc1_slope2 = 69,
.agc2_pt1 = 0,
.agc2_pt2 = 59,
.agc2_slope1 = 111,
.agc2_slope2 = 28,
};
static struct dib3000mc_config bristol_dib3000mc_config[2] = {
{ .agc = &bristol_dib3000p_mt2060_agc_config,
.max_time = 0x196,
.ln_adc_level = 0x1cc7,
.output_mpeg2_in_188_bytes = 1,
},
{ .agc = &bristol_dib3000p_mt2060_agc_config,
.max_time = 0x196,
.ln_adc_level = 0x1cc7,
.output_mpeg2_in_188_bytes = 1,
}
};
static int bristol_frontend_attach(struct dvb_usb_adapter *adap)
{
struct dib0700_state *st = adap->dev->priv;
if (adap->id == 0) {
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0); msleep(10);
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1); msleep(10);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0); msleep(10);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1); msleep(10);
if (force_lna_activation)
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
else
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 0);
if (dib3000mc_i2c_enumeration(&adap->dev->i2c_adap, 2, DEFAULT_DIB3000P_I2C_ADDRESS, bristol_dib3000mc_config) != 0) {
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0); msleep(10);
return -ENODEV;
}
}
st->mt2060_if1[adap->id] = 1220;
return (adap->fe = dvb_attach(dib3000mc_attach, &adap->dev->i2c_adap,
(10 + adap->id) << 1, &bristol_dib3000mc_config[adap->id])) == NULL ? -ENODEV : 0;
}
static int eeprom_read(struct i2c_adapter *adap,u8 adrs,u8 *pval)
{
struct i2c_msg msg[2] = {
{ .addr = 0x50, .flags = 0, .buf = &adrs, .len = 1 },
{ .addr = 0x50, .flags = I2C_M_RD, .buf = pval, .len = 1 },
};
if (i2c_transfer(adap, msg, 2) != 2) return -EREMOTEIO;
return 0;
}
static int bristol_tuner_attach(struct dvb_usb_adapter *adap)
{
struct i2c_adapter *prim_i2c = &adap->dev->i2c_adap;
struct i2c_adapter *tun_i2c = dib3000mc_get_tuner_i2c_master(adap->fe, 1);
s8 a;
int if1=1220;
if (adap->dev->udev->descriptor.idVendor == USB_VID_HAUPPAUGE &&
adap->dev->udev->descriptor.idProduct == USB_PID_HAUPPAUGE_NOVA_T_500_2) {
if (!eeprom_read(prim_i2c,0x59 + adap->id,&a)) if1=1220+a;
}
return dvb_attach(mt2060_attach,adap->fe, tun_i2c,&bristol_mt2060_config[adap->id],
if1) == NULL ? -ENODEV : 0;
}
/* STK7700D: Pinnacle/Terratec/Hauppauge Dual DVB-T Diversity */
/* MT226x */
static struct dibx000_agc_config stk7700d_7000p_mt2266_agc_config[2] = {
{
BAND_UHF, // band_caps
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=1, P_agc_inv_pwm1=1, P_agc_inv_pwm2=1,
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=2, P_agc_write=0 */
(0 << 15) | (0 << 14) | (1 << 11) | (1 << 10) | (1 << 9) | (0 << 8) | (3 << 5) | (0 << 4) | (5 << 1) | (0 << 0), // setup
1130, // inv_gain
21, // time_stabiliz
0, // alpha_level
118, // thlock
0, // wbd_inv
3530, // wbd_ref
1, // wbd_sel
0, // wbd_alpha
65535, // agc1_max
33770, // agc1_min
65535, // agc2_max
23592, // agc2_min
0, // agc1_pt1
62, // agc1_pt2
255, // agc1_pt3
64, // agc1_slope1
64, // agc1_slope2
132, // agc2_pt1
192, // agc2_pt2
80, // agc2_slope1
80, // agc2_slope2
17, // alpha_mant
27, // alpha_exp
23, // beta_mant
51, // beta_exp
1, // perform_agc_softsplit
}, {
BAND_VHF | BAND_LBAND, // band_caps
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=1, P_agc_inv_pwm1=1, P_agc_inv_pwm2=1,
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=2, P_agc_write=0 */
(0 << 15) | (0 << 14) | (1 << 11) | (1 << 10) | (1 << 9) | (0 << 8) | (3 << 5) | (0 << 4) | (2 << 1) | (0 << 0), // setup
2372, // inv_gain
21, // time_stabiliz
0, // alpha_level
118, // thlock
0, // wbd_inv
3530, // wbd_ref
1, // wbd_sel
0, // wbd_alpha
65535, // agc1_max
0, // agc1_min
65535, // agc2_max
23592, // agc2_min
0, // agc1_pt1
128, // agc1_pt2
128, // agc1_pt3
128, // agc1_slope1
0, // agc1_slope2
128, // agc2_pt1
253, // agc2_pt2
81, // agc2_slope1
0, // agc2_slope2
17, // alpha_mant
27, // alpha_exp
23, // beta_mant
51, // beta_exp
1, // perform_agc_softsplit
}
};
static struct dibx000_bandwidth_config stk7700d_mt2266_pll_config = {
60000, 30000, // internal, sampling
1, 8, 3, 1, 0, // pll_cfg: prediv, ratio, range, reset, bypass
0, 0, 1, 1, 2, // misc: refdiv, bypclk_div, IO_CLK_en_core, ADClkSrc, modulo
(3 << 14) | (1 << 12) | (524 << 0), // sad_cfg: refsel, sel, freq_15k
0, // ifreq
20452225, // timf
};
static struct dib7000p_config stk7700d_dib7000p_mt2266_config[] = {
{ .output_mpeg2_in_188_bytes = 1,
.hostbus_diversity = 1,
.tuner_is_baseband = 1,
.agc_config_count = 2,
.agc = stk7700d_7000p_mt2266_agc_config,
.bw = &stk7700d_mt2266_pll_config,
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
},
{ .output_mpeg2_in_188_bytes = 1,
.hostbus_diversity = 1,
.tuner_is_baseband = 1,
.agc_config_count = 2,
.agc = stk7700d_7000p_mt2266_agc_config,
.bw = &stk7700d_mt2266_pll_config,
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
}
};
static struct mt2266_config stk7700d_mt2266_config[2] = {
{ .i2c_address = 0x60
},
{ .i2c_address = 0x60
}
};
static int stk7700P2_frontend_attach(struct dvb_usb_adapter *adap)
{
if (adap->id == 0) {
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
msleep(10);
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
msleep(10);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
msleep(10);
dib7000p_i2c_enumeration(&adap->dev->i2c_adap,1,18,stk7700d_dib7000p_mt2266_config);
}
adap->fe = dvb_attach(dib7000p_attach, &adap->dev->i2c_adap,0x80+(adap->id << 1),
&stk7700d_dib7000p_mt2266_config[adap->id]);
return adap->fe == NULL ? -ENODEV : 0;
}
static int stk7700d_frontend_attach(struct dvb_usb_adapter *adap)
{
if (adap->id == 0) {
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
msleep(10);
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
msleep(10);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
msleep(10);
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
dib7000p_i2c_enumeration(&adap->dev->i2c_adap,2,18,stk7700d_dib7000p_mt2266_config);
}
adap->fe = dvb_attach(dib7000p_attach, &adap->dev->i2c_adap,0x80+(adap->id << 1),
&stk7700d_dib7000p_mt2266_config[adap->id]);
return adap->fe == NULL ? -ENODEV : 0;
}
static int stk7700d_tuner_attach(struct dvb_usb_adapter *adap)
{
struct i2c_adapter *tun_i2c;
tun_i2c = dib7000p_get_i2c_master(adap->fe, DIBX000_I2C_INTERFACE_TUNER, 1);
return dvb_attach(mt2266_attach, adap->fe, tun_i2c,
&stk7700d_mt2266_config[adap->id]) == NULL ? -ENODEV : 0;;
}
#define DEFAULT_RC_INTERVAL 150
static u8 rc_request[] = { REQUEST_POLL_RC, 0 };
static int dib0700_rc_query(struct dvb_usb_device *d, u32 *event, int *state)
{
u8 key[4];
int i;
struct dvb_usb_rc_key *keymap = d->props.rc_key_map;
struct dib0700_state *st = d->priv;
*event = 0;
*state = REMOTE_NO_KEY_PRESSED;
i=dib0700_ctrl_rd(d,rc_request,2,key,4);
if (i<=0) {
err("RC Query Failed");
return -1;
}
if (key[0]==0 && key[1]==0 && key[2]==0 && key[3]==0) return 0;
if (key[3-1]!=st->rc_toggle) {
for (i=0;i<d->props.rc_key_map_size; i++) {
if (keymap[i].custom == key[3-2] && keymap[i].data == key[3-3]) {
*event = keymap[i].event;
*state = REMOTE_KEY_PRESSED;
st->rc_toggle=key[3-1];
return 0;
}
}
err("Unknown remote controller key : %2X %2X",(int)key[3-2],(int)key[3-3]);
}
return 0;
}
static struct dvb_usb_rc_key dib0700_rc_keys[] = {
/* Key codes for the tiny Pinnacle remote*/
{ 0x07, 0x00, KEY_MUTE },
{ 0x07, 0x01, KEY_MENU }, // Pinnacle logo
{ 0x07, 0x39, KEY_POWER },
{ 0x07, 0x03, KEY_VOLUMEUP },
{ 0x07, 0x09, KEY_VOLUMEDOWN },
{ 0x07, 0x06, KEY_CHANNELUP },
{ 0x07, 0x0c, KEY_CHANNELDOWN },
{ 0x07, 0x0f, KEY_1 },
{ 0x07, 0x15, KEY_2 },
{ 0x07, 0x10, KEY_3 },
{ 0x07, 0x18, KEY_4 },
{ 0x07, 0x1b, KEY_5 },
{ 0x07, 0x1e, KEY_6 },
{ 0x07, 0x11, KEY_7 },
{ 0x07, 0x21, KEY_8 },
{ 0x07, 0x12, KEY_9 },
{ 0x07, 0x27, KEY_0 },
{ 0x07, 0x24, KEY_SCREEN }, // 'Square' key
{ 0x07, 0x2a, KEY_TEXT }, // 'T' key
{ 0x07, 0x2d, KEY_REWIND },
{ 0x07, 0x30, KEY_PLAY },
{ 0x07, 0x33, KEY_FASTFORWARD },
{ 0x07, 0x36, KEY_RECORD },
{ 0x07, 0x3c, KEY_STOP },
{ 0x07, 0x3f, KEY_CANCEL }, // '?' key
/* Key codes for the Terratec Cinergy DT XS Diversity, similar to cinergyT2.c */
{ 0xeb, 0x01, KEY_POWER },
{ 0xeb, 0x02, KEY_1 },
{ 0xeb, 0x03, KEY_2 },
{ 0xeb, 0x04, KEY_3 },
{ 0xeb, 0x05, KEY_4 },
{ 0xeb, 0x06, KEY_5 },
{ 0xeb, 0x07, KEY_6 },
{ 0xeb, 0x08, KEY_7 },
{ 0xeb, 0x09, KEY_8 },
{ 0xeb, 0x0a, KEY_9 },
{ 0xeb, 0x0b, KEY_VIDEO },
{ 0xeb, 0x0c, KEY_0 },
{ 0xeb, 0x0d, KEY_REFRESH },
{ 0xeb, 0x0f, KEY_EPG },
{ 0xeb, 0x10, KEY_UP },
{ 0xeb, 0x11, KEY_LEFT },
{ 0xeb, 0x12, KEY_OK },
{ 0xeb, 0x13, KEY_RIGHT },
{ 0xeb, 0x14, KEY_DOWN },
{ 0xeb, 0x16, KEY_INFO },
{ 0xeb, 0x17, KEY_RED },
{ 0xeb, 0x18, KEY_GREEN },
{ 0xeb, 0x19, KEY_YELLOW },
{ 0xeb, 0x1a, KEY_BLUE },
{ 0xeb, 0x1b, KEY_CHANNELUP },
{ 0xeb, 0x1c, KEY_VOLUMEUP },
{ 0xeb, 0x1d, KEY_MUTE },
{ 0xeb, 0x1e, KEY_VOLUMEDOWN },
{ 0xeb, 0x1f, KEY_CHANNELDOWN },
{ 0xeb, 0x40, KEY_PAUSE },
{ 0xeb, 0x41, KEY_HOME },
{ 0xeb, 0x42, KEY_MENU }, /* DVD Menu */
{ 0xeb, 0x43, KEY_SUBTITLE },
{ 0xeb, 0x44, KEY_TEXT }, /* Teletext */
{ 0xeb, 0x45, KEY_DELETE },
{ 0xeb, 0x46, KEY_TV },
{ 0xeb, 0x47, KEY_DVD },
{ 0xeb, 0x48, KEY_STOP },
{ 0xeb, 0x49, KEY_VIDEO },
{ 0xeb, 0x4a, KEY_AUDIO }, /* Music */
{ 0xeb, 0x4b, KEY_SCREEN }, /* Pic */
{ 0xeb, 0x4c, KEY_PLAY },
{ 0xeb, 0x4d, KEY_BACK },
{ 0xeb, 0x4e, KEY_REWIND },
{ 0xeb, 0x4f, KEY_FASTFORWARD },
{ 0xeb, 0x54, KEY_PREVIOUS },
{ 0xeb, 0x58, KEY_RECORD },
{ 0xeb, 0x5c, KEY_NEXT },
/* Key codes for the Haupauge WinTV Nova-TD, copied from nova-t-usb2.c (Nova-T USB2) */
{ 0x1e, 0x00, KEY_0 },
{ 0x1e, 0x01, KEY_1 },
{ 0x1e, 0x02, KEY_2 },
{ 0x1e, 0x03, KEY_3 },
{ 0x1e, 0x04, KEY_4 },
{ 0x1e, 0x05, KEY_5 },
{ 0x1e, 0x06, KEY_6 },
{ 0x1e, 0x07, KEY_7 },
{ 0x1e, 0x08, KEY_8 },
{ 0x1e, 0x09, KEY_9 },
{ 0x1e, 0x0a, KEY_KPASTERISK },
{ 0x1e, 0x0b, KEY_RED },
{ 0x1e, 0x0c, KEY_RADIO },
{ 0x1e, 0x0d, KEY_MENU },
{ 0x1e, 0x0e, KEY_GRAVE }, /* # */
{ 0x1e, 0x0f, KEY_MUTE },
{ 0x1e, 0x10, KEY_VOLUMEUP },
{ 0x1e, 0x11, KEY_VOLUMEDOWN },
{ 0x1e, 0x12, KEY_CHANNEL },
{ 0x1e, 0x14, KEY_UP },
{ 0x1e, 0x15, KEY_DOWN },
{ 0x1e, 0x16, KEY_LEFT },
{ 0x1e, 0x17, KEY_RIGHT },
{ 0x1e, 0x18, KEY_VIDEO },
{ 0x1e, 0x19, KEY_AUDIO },
{ 0x1e, 0x1a, KEY_MEDIA },
{ 0x1e, 0x1b, KEY_EPG },
{ 0x1e, 0x1c, KEY_TV },
{ 0x1e, 0x1e, KEY_NEXT },
{ 0x1e, 0x1f, KEY_BACK },
{ 0x1e, 0x20, KEY_CHANNELUP },
{ 0x1e, 0x21, KEY_CHANNELDOWN },
{ 0x1e, 0x24, KEY_LAST }, /* Skip backwards */
{ 0x1e, 0x25, KEY_OK },
{ 0x1e, 0x29, KEY_BLUE},
{ 0x1e, 0x2e, KEY_GREEN },
{ 0x1e, 0x30, KEY_PAUSE },
{ 0x1e, 0x32, KEY_REWIND },
{ 0x1e, 0x34, KEY_FASTFORWARD },
{ 0x1e, 0x35, KEY_PLAY },
{ 0x1e, 0x36, KEY_STOP },
{ 0x1e, 0x37, KEY_RECORD },
{ 0x1e, 0x38, KEY_YELLOW },
{ 0x1e, 0x3b, KEY_GOTO },
{ 0x1e, 0x3d, KEY_POWER },
/* Key codes for the Leadtek Winfast DTV Dongle */
{ 0x00, 0x42, KEY_POWER },
{ 0x07, 0x7c, KEY_TUNER },
{ 0x0f, 0x4e, KEY_PRINT }, /* PREVIEW */
{ 0x08, 0x40, KEY_SCREEN }, /* full screen toggle*/
{ 0x0f, 0x71, KEY_DOT }, /* frequency */
{ 0x07, 0x43, KEY_0 },
{ 0x0c, 0x41, KEY_1 },
{ 0x04, 0x43, KEY_2 },
{ 0x0b, 0x7f, KEY_3 },
{ 0x0e, 0x41, KEY_4 },
{ 0x06, 0x43, KEY_5 },
{ 0x09, 0x7f, KEY_6 },
{ 0x0d, 0x7e, KEY_7 },
{ 0x05, 0x7c, KEY_8 },
{ 0x0a, 0x40, KEY_9 },
{ 0x0e, 0x4e, KEY_CLEAR },
{ 0x04, 0x7c, KEY_CHANNEL }, /* show channel number */
{ 0x0f, 0x41, KEY_LAST }, /* recall */
{ 0x03, 0x42, KEY_MUTE },
{ 0x06, 0x4c, KEY_RESERVED }, /* PIP button*/
{ 0x01, 0x72, KEY_SHUFFLE }, /* SNAPSHOT */
{ 0x0c, 0x4e, KEY_PLAYPAUSE }, /* TIMESHIFT */
{ 0x0b, 0x70, KEY_RECORD },
{ 0x03, 0x7d, KEY_VOLUMEUP },
{ 0x01, 0x7d, KEY_VOLUMEDOWN },
{ 0x02, 0x42, KEY_CHANNELUP },
{ 0x00, 0x7d, KEY_CHANNELDOWN },
};
/* STK7700P: Hauppauge Nova-T Stick, AVerMedia Volar */
static struct dibx000_agc_config stk7700p_7000m_mt2060_agc_config = {
BAND_UHF | BAND_VHF, // band_caps
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=5, P_agc_inv_pwm1=0, P_agc_inv_pwm2=0,
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=2, P_agc_write=0 */
(0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) | (0 << 8) | (3 << 5) | (0 << 4) | (2 << 1) | (0 << 0), // setup
712, // inv_gain
41, // time_stabiliz
0, // alpha_level
118, // thlock
0, // wbd_inv
4095, // wbd_ref
0, // wbd_sel
0, // wbd_alpha
42598, // agc1_max
17694, // agc1_min
45875, // agc2_max
2621, // agc2_min
0, // agc1_pt1
76, // agc1_pt2
139, // agc1_pt3
52, // agc1_slope1
59, // agc1_slope2
107, // agc2_pt1
172, // agc2_pt2
57, // agc2_slope1
70, // agc2_slope2
21, // alpha_mant
25, // alpha_exp
28, // beta_mant
48, // beta_exp
1, // perform_agc_softsplit
{ 0, // split_min
107, // split_max
51800, // global_split_min
24700 // global_split_max
},
};
static struct dibx000_agc_config stk7700p_7000p_mt2060_agc_config = {
BAND_UHF | BAND_VHF,
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=5, P_agc_inv_pwm1=0, P_agc_inv_pwm2=0,
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=2, P_agc_write=0 */
(0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) | (0 << 8) | (3 << 5) | (0 << 4) | (2 << 1) | (0 << 0), // setup
712, // inv_gain
41, // time_stabiliz
0, // alpha_level
118, // thlock
0, // wbd_inv
4095, // wbd_ref
0, // wbd_sel
0, // wbd_alpha
42598, // agc1_max
16384, // agc1_min
42598, // agc2_max
0, // agc2_min
0, // agc1_pt1
137, // agc1_pt2
255, // agc1_pt3
0, // agc1_slope1
255, // agc1_slope2
0, // agc2_pt1
0, // agc2_pt2
0, // agc2_slope1
41, // agc2_slope2
15, // alpha_mant
25, // alpha_exp
28, // beta_mant
48, // beta_exp
0, // perform_agc_softsplit
};
static struct dibx000_bandwidth_config stk7700p_pll_config = {
60000, 30000, // internal, sampling
1, 8, 3, 1, 0, // pll_cfg: prediv, ratio, range, reset, bypass
0, 0, 1, 1, 0, // misc: refdiv, bypclk_div, IO_CLK_en_core, ADClkSrc, modulo
(3 << 14) | (1 << 12) | (524 << 0), // sad_cfg: refsel, sel, freq_15k
60258167, // ifreq
20452225, // timf
30000000, // xtal
};
static struct dib7000m_config stk7700p_dib7000m_config = {
.dvbt_mode = 1,
.output_mpeg2_in_188_bytes = 1,
.quartz_direct = 1,
.agc_config_count = 1,
.agc = &stk7700p_7000m_mt2060_agc_config,
.bw = &stk7700p_pll_config,
.gpio_dir = DIB7000M_GPIO_DEFAULT_DIRECTIONS,
.gpio_val = DIB7000M_GPIO_DEFAULT_VALUES,
.gpio_pwm_pos = DIB7000M_GPIO_DEFAULT_PWM_POS,
};
static struct dib7000p_config stk7700p_dib7000p_config = {
.output_mpeg2_in_188_bytes = 1,
.agc_config_count = 1,
.agc = &stk7700p_7000p_mt2060_agc_config,
.bw = &stk7700p_pll_config,
.gpio_dir = DIB7000M_GPIO_DEFAULT_DIRECTIONS,
.gpio_val = DIB7000M_GPIO_DEFAULT_VALUES,
.gpio_pwm_pos = DIB7000M_GPIO_DEFAULT_PWM_POS,
};
static int stk7700p_frontend_attach(struct dvb_usb_adapter *adap)
{
struct dib0700_state *st = adap->dev->priv;
/* unless there is no real power management in DVB - we leave the device on GPIO6 */
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0); msleep(50);
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1); msleep(10);
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0); msleep(10);
dib0700_ctrl_clock(adap->dev, 72, 1);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1); msleep(100);
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
st->mt2060_if1[0] = 1220;
if (dib7000pc_detection(&adap->dev->i2c_adap)) {
adap->fe = dvb_attach(dib7000p_attach, &adap->dev->i2c_adap, 18, &stk7700p_dib7000p_config);
st->is_dib7000pc = 1;
} else
adap->fe = dvb_attach(dib7000m_attach, &adap->dev->i2c_adap, 18, &stk7700p_dib7000m_config);
return adap->fe == NULL ? -ENODEV : 0;
}
static struct mt2060_config stk7700p_mt2060_config = {
0x60
};
static int stk7700p_tuner_attach(struct dvb_usb_adapter *adap)
{
struct i2c_adapter *prim_i2c = &adap->dev->i2c_adap;
struct dib0700_state *st = adap->dev->priv;
struct i2c_adapter *tun_i2c;
s8 a;
int if1=1220;
if (adap->dev->udev->descriptor.idVendor == USB_VID_HAUPPAUGE &&
adap->dev->udev->descriptor.idProduct == USB_PID_HAUPPAUGE_NOVA_T_STICK) {
if (!eeprom_read(prim_i2c,0x58,&a)) if1=1220+a;
}
if (st->is_dib7000pc)
tun_i2c = dib7000p_get_i2c_master(adap->fe, DIBX000_I2C_INTERFACE_TUNER, 1);
else
tun_i2c = dib7000m_get_i2c_master(adap->fe, DIBX000_I2C_INTERFACE_TUNER, 1);
return dvb_attach(mt2060_attach, adap->fe, tun_i2c, &stk7700p_mt2060_config,
if1) == NULL ? -ENODEV : 0;
}
/* DIB7070 generic */
static struct dibx000_agc_config dib7070_agc_config = {
BAND_UHF | BAND_VHF | BAND_LBAND | BAND_SBAND,
/* P_agc_use_sd_mod1=0, P_agc_use_sd_mod2=0, P_agc_freq_pwm_div=5, P_agc_inv_pwm1=0, P_agc_inv_pwm2=0,
* P_agc_inh_dc_rv_est=0, P_agc_time_est=3, P_agc_freeze=0, P_agc_nb_est=5, P_agc_write=0 */
(0 << 15) | (0 << 14) | (5 << 11) | (0 << 10) | (0 << 9) | (0 << 8) | (3 << 5) | (0 << 4) | (5 << 1) | (0 << 0), // setup
600, // inv_gain
10, // time_stabiliz
0, // alpha_level
118, // thlock
0, // wbd_inv
3530, // wbd_ref
1, // wbd_sel
5, // wbd_alpha
65535, // agc1_max
0, // agc1_min
65535, // agc2_max
0, // agc2_min
0, // agc1_pt1
40, // agc1_pt2
183, // agc1_pt3
206, // agc1_slope1
255, // agc1_slope2
72, // agc2_pt1
152, // agc2_pt2
88, // agc2_slope1
90, // agc2_slope2
17, // alpha_mant
27, // alpha_exp
23, // beta_mant
51, // beta_exp
0, // perform_agc_softsplit
};
static int dib7070_tuner_reset(struct dvb_frontend *fe, int onoff)
{
return dib7000p_set_gpio(fe, 8, 0, !onoff);
}
static int dib7070_tuner_sleep(struct dvb_frontend *fe, int onoff)
{
return dib7000p_set_gpio(fe, 9, 0, onoff);
}
static struct dib0070_config dib7070p_dib0070_config[2] = {
{
.i2c_address = DEFAULT_DIB0070_I2C_ADDRESS,
.reset = dib7070_tuner_reset,
.sleep = dib7070_tuner_sleep,
.clock_khz = 12000,
.clock_pad_drive = 4
}, {
.i2c_address = DEFAULT_DIB0070_I2C_ADDRESS,
.reset = dib7070_tuner_reset,
.sleep = dib7070_tuner_sleep,
.clock_khz = 12000,
}
};
static int dib7070_set_param_override(struct dvb_frontend *fe, struct dvb_frontend_parameters *fep)
{
struct dvb_usb_adapter *adap = fe->dvb->priv;
struct dib0700_adapter_state *state = adap->priv;
u16 offset;
u8 band = BAND_OF_FREQUENCY(fep->frequency/1000);
switch (band) {
case BAND_VHF: offset = 950; break;
case BAND_UHF:
default: offset = 550; break;
}
deb_info("WBD for DiB7000P: %d\n", offset + dib0070_wbd_offset(fe));
dib7000p_set_wbd_ref(fe, offset + dib0070_wbd_offset(fe));
return state->set_param_save(fe, fep);
}
static int dib7070p_tuner_attach(struct dvb_usb_adapter *adap)
{
struct dib0700_adapter_state *st = adap->priv;
struct i2c_adapter *tun_i2c = dib7000p_get_i2c_master(adap->fe, DIBX000_I2C_INTERFACE_TUNER, 1);
if (adap->id == 0) {
if (dvb_attach(dib0070_attach, adap->fe, tun_i2c, &dib7070p_dib0070_config[0]) == NULL)
return -ENODEV;
} else {
if (dvb_attach(dib0070_attach, adap->fe, tun_i2c, &dib7070p_dib0070_config[1]) == NULL)
return -ENODEV;
}
st->set_param_save = adap->fe->ops.tuner_ops.set_params;
adap->fe->ops.tuner_ops.set_params = dib7070_set_param_override;
return 0;
}
static struct dibx000_bandwidth_config dib7070_bw_config_12_mhz = {
60000, 15000, // internal, sampling
1, 20, 3, 1, 0, // pll_cfg: prediv, ratio, range, reset, bypass
0, 0, 1, 1, 2, // misc: refdiv, bypclk_div, IO_CLK_en_core, ADClkSrc, modulo
(3 << 14) | (1 << 12) | (524 << 0), // sad_cfg: refsel, sel, freq_15k
(0 << 25) | 0, // ifreq = 0.000000 MHz
20452225, // timf
12000000, // xtal_hz
};
static struct dib7000p_config dib7070p_dib7000p_config = {
.output_mpeg2_in_188_bytes = 1,
.agc_config_count = 1,
.agc = &dib7070_agc_config,
.bw = &dib7070_bw_config_12_mhz,
.tuner_is_baseband = 1,
.spur_protect = 1,
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
.hostbus_diversity = 1,
};
/* STK7070P */
static int stk7070p_frontend_attach(struct dvb_usb_adapter *adap)
{
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
msleep(10);
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
dib0700_ctrl_clock(adap->dev, 72, 1);
msleep(10);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
msleep(10);
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
dib7000p_i2c_enumeration(&adap->dev->i2c_adap, 1, 18, &dib7070p_dib7000p_config);
adap->fe = dvb_attach(dib7000p_attach, &adap->dev->i2c_adap, 0x80, &dib7070p_dib7000p_config);
return adap->fe == NULL ? -ENODEV : 0;
}
/* STK7070PD */
static struct dib7000p_config stk7070pd_dib7000p_config[2] = {
{
.output_mpeg2_in_188_bytes = 1,
.agc_config_count = 1,
.agc = &dib7070_agc_config,
.bw = &dib7070_bw_config_12_mhz,
.tuner_is_baseband = 1,
.spur_protect = 1,
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
.hostbus_diversity = 1,
}, {
.output_mpeg2_in_188_bytes = 1,
.agc_config_count = 1,
.agc = &dib7070_agc_config,
.bw = &dib7070_bw_config_12_mhz,
.tuner_is_baseband = 1,
.spur_protect = 1,
.gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
.gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
.gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
.hostbus_diversity = 1,
}
};
static int stk7070pd_frontend_attach0(struct dvb_usb_adapter *adap)
{
dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
msleep(10);
dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
dib0700_ctrl_clock(adap->dev, 72, 1);
msleep(10);
dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
msleep(10);
dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
dib7000p_i2c_enumeration(&adap->dev->i2c_adap, 2, 18, stk7070pd_dib7000p_config);
adap->fe = dvb_attach(dib7000p_attach, &adap->dev->i2c_adap, 0x80, &stk7070pd_dib7000p_config[0]);
return adap->fe == NULL ? -ENODEV : 0;
}
static int stk7070pd_frontend_attach1(struct dvb_usb_adapter *adap)
{
adap->fe = dvb_attach(dib7000p_attach, &adap->dev->i2c_adap, 0x82, &stk7070pd_dib7000p_config[1]);
return adap->fe == NULL ? -ENODEV : 0;
}
/* DVB-USB and USB stuff follows */
struct usb_device_id dib0700_usb_id_table[] = {
/* 0 */ { USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK7700P) },
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK7700P_PC) },
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_500) },
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_500_2) },
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_STICK) },
/* 5 */ { USB_DEVICE(USB_VID_AVERMEDIA, USB_PID_AVERMEDIA_VOLAR) },
{ USB_DEVICE(USB_VID_COMPRO, USB_PID_COMPRO_VIDEOMATE_U500) },
{ USB_DEVICE(USB_VID_UNIWILL, USB_PID_UNIWILL_STK7700P) },
{ USB_DEVICE(USB_VID_LEADTEK, USB_PID_WINFAST_DTV_DONGLE_STK7700P) },
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_STICK_2) },
/* 10 */{ USB_DEVICE(USB_VID_AVERMEDIA, USB_PID_AVERMEDIA_VOLAR_2) },
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV2000E) },
{ USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_CINERGY_DT_XS_DIVERSITY) },
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_TD_STICK) },
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK7700D) },
/* 15 */{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK7070P) },
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV_DVB_T_FLASH) },
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK7070PD) },
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV_DUAL_DIVERSITY_DVB_T) },
{ USB_DEVICE(USB_VID_COMPRO, USB_PID_COMPRO_VIDEOMATE_U500_PC) },
/* 20 */{ USB_DEVICE(USB_VID_AVERMEDIA, USB_PID_AVERMEDIA_EXPRESS) },
{ USB_DEVICE(USB_VID_GIGABYTE, USB_PID_GIGABYTE_U7000) },
{ USB_DEVICE(USB_VID_ULTIMA_ELECTRONIC, USB_PID_ARTEC_T14BR) },
{ USB_DEVICE(USB_VID_ASUS, USB_PID_ASUS_U3000) },
{ USB_DEVICE(USB_VID_ASUS, USB_PID_ASUS_U3100) },
/* 25 */ { USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_NOVA_T_STICK_3) },
{ USB_DEVICE(USB_VID_HAUPPAUGE, USB_PID_HAUPPAUGE_MYTV_T) },
{ USB_DEVICE(USB_VID_YUAN, USB_PID_YUAN_EC372S) },
{ 0 } /* Terminating entry */
};
MODULE_DEVICE_TABLE(usb, dib0700_usb_id_table);
#define DIB0700_DEFAULT_DEVICE_PROPERTIES \
.caps = DVB_USB_IS_AN_I2C_ADAPTER, \
.usb_ctrl = DEVICE_SPECIFIC, \
.firmware = "dvb-usb-dib0700-1.10.fw", \
.download_firmware = dib0700_download_firmware, \
.no_reconnect = 1, \
.size_of_priv = sizeof(struct dib0700_state), \
.i2c_algo = &dib0700_i2c_algo, \
.identify_state = dib0700_identify_state
#define DIB0700_DEFAULT_STREAMING_CONFIG(ep) \
.streaming_ctrl = dib0700_streaming_ctrl, \
.stream = { \
.type = USB_BULK, \
.count = 4, \
.endpoint = ep, \
.u = { \
.bulk = { \
.buffersize = 39480, \
} \
} \
}
struct dvb_usb_device_properties dib0700_devices[] = {
{
DIB0700_DEFAULT_DEVICE_PROPERTIES,
.num_adapters = 1,
.adapter = {
{
.frontend_attach = stk7700p_frontend_attach,
.tuner_attach = stk7700p_tuner_attach,
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
},
},
.num_device_descs = 8,
.devices = {
{ "DiBcom STK7700P reference design",
{ &dib0700_usb_id_table[0], &dib0700_usb_id_table[1] },
{ NULL },
},
{ "Hauppauge Nova-T Stick",
{ &dib0700_usb_id_table[4], &dib0700_usb_id_table[9], NULL },
{ NULL },
},
{ "AVerMedia AVerTV DVB-T Volar",
{ &dib0700_usb_id_table[5], &dib0700_usb_id_table[10] },
{ NULL },
},
{ "Compro Videomate U500",
{ &dib0700_usb_id_table[6], &dib0700_usb_id_table[19] },
{ NULL },
},
{ "Uniwill STK7700P based (Hama and others)",
{ &dib0700_usb_id_table[7], NULL },
{ NULL },
},
{ "Leadtek Winfast DTV Dongle (STK7700P based)",
{ &dib0700_usb_id_table[8], NULL },
{ NULL },
},
{ "AVerMedia AVerTV DVB-T Express",
{ &dib0700_usb_id_table[20] },
{ NULL },
},
{ "Gigabyte U7000",
{ &dib0700_usb_id_table[21], NULL },
{ NULL },
}
},
.rc_interval = DEFAULT_RC_INTERVAL,
.rc_key_map = dib0700_rc_keys,
.rc_key_map_size = ARRAY_SIZE(dib0700_rc_keys),
.rc_query = dib0700_rc_query
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
.num_adapters = 2,
.adapter = {
{
.frontend_attach = bristol_frontend_attach,
.tuner_attach = bristol_tuner_attach,
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
}, {
.frontend_attach = bristol_frontend_attach,
.tuner_attach = bristol_tuner_attach,
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
}
},
.num_device_descs = 1,
.devices = {
{ "Hauppauge Nova-T 500 Dual DVB-T",
{ &dib0700_usb_id_table[2], &dib0700_usb_id_table[3], NULL },
{ NULL },
},
},
.rc_interval = DEFAULT_RC_INTERVAL,
.rc_key_map = dib0700_rc_keys,
.rc_key_map_size = ARRAY_SIZE(dib0700_rc_keys),
.rc_query = dib0700_rc_query
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
.num_adapters = 2,
.adapter = {
{
.frontend_attach = stk7700d_frontend_attach,
.tuner_attach = stk7700d_tuner_attach,
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
}, {
.frontend_attach = stk7700d_frontend_attach,
.tuner_attach = stk7700d_tuner_attach,
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
}
},
.num_device_descs = 4,
.devices = {
{ "Pinnacle PCTV 2000e",
{ &dib0700_usb_id_table[11], NULL },
{ NULL },
},
{ "Terratec Cinergy DT XS Diversity",
{ &dib0700_usb_id_table[12], NULL },
{ NULL },
},
{ "Hauppauge Nova-TD Stick/Elgato Eye-TV Diversity",
{ &dib0700_usb_id_table[13], NULL },
{ NULL },
},
{ "DiBcom STK7700D reference design",
{ &dib0700_usb_id_table[14], NULL },
{ NULL },
}
},
.rc_interval = DEFAULT_RC_INTERVAL,
.rc_key_map = dib0700_rc_keys,
.rc_key_map_size = ARRAY_SIZE(dib0700_rc_keys),
.rc_query = dib0700_rc_query
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
.num_adapters = 1,
.adapter = {
{
.frontend_attach = stk7700P2_frontend_attach,
.tuner_attach = stk7700d_tuner_attach,
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
},
},
.num_device_descs = 2,
.devices = {
{ "ASUS My Cinema U3000 Mini DVBT Tuner",
{ &dib0700_usb_id_table[23], NULL },
{ NULL },
},
{ "Yuan EC372S",
{ &dib0700_usb_id_table[27], NULL },
{ NULL },
}
}
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
.num_adapters = 1,
.adapter = {
{
.frontend_attach = stk7070p_frontend_attach,
.tuner_attach = dib7070p_tuner_attach,
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
.size_of_priv = sizeof(struct dib0700_adapter_state),
},
},
.num_device_descs = 6,
.devices = {
{ "DiBcom STK7070P reference design",
{ &dib0700_usb_id_table[15], NULL },
{ NULL },
},
{ "Pinnacle PCTV DVB-T Flash Stick",
{ &dib0700_usb_id_table[16], NULL },
{ NULL },
},
{ "Artec T14BR DVB-T",
{ &dib0700_usb_id_table[22], NULL },
{ NULL },
},
{ "ASUS My Cinema U3100 Mini DVBT Tuner",
{ &dib0700_usb_id_table[24], NULL },
{ NULL },
},
{ "Hauppauge Nova-T Stick",
{ &dib0700_usb_id_table[25], NULL },
{ NULL },
},
{ "Hauppauge Nova-T MyTV.t",
{ &dib0700_usb_id_table[26], NULL },
{ NULL },
},
},
.rc_interval = DEFAULT_RC_INTERVAL,
.rc_key_map = dib0700_rc_keys,
.rc_key_map_size = ARRAY_SIZE(dib0700_rc_keys),
.rc_query = dib0700_rc_query
}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
.num_adapters = 2,
.adapter = {
{
.frontend_attach = stk7070pd_frontend_attach0,
.tuner_attach = dib7070p_tuner_attach,
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
.size_of_priv = sizeof(struct dib0700_adapter_state),
}, {
.frontend_attach = stk7070pd_frontend_attach1,
.tuner_attach = dib7070p_tuner_attach,
DIB0700_DEFAULT_STREAMING_CONFIG(0x03),
.size_of_priv = sizeof(struct dib0700_adapter_state),
}
},
.num_device_descs = 2,
.devices = {
{ "DiBcom STK7070PD reference design",
{ &dib0700_usb_id_table[17], NULL },
{ NULL },
},
{ "Pinnacle PCTV Dual DVB-T Diversity Stick",
{ &dib0700_usb_id_table[18], NULL },
{ NULL },
}
}
},
};
int dib0700_device_count = ARRAY_SIZE(dib0700_devices);
[-- Attachment #3: Type: text/plain, Size: 150 bytes --]
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [linux-dvb] Yuan EC372S (STK7700D based device)
2008-02-18 22:53 ` Antti Palosaari
@ 2008-02-18 23:30 ` Albert Comerma
2008-02-20 12:48 ` Antti Palosaari
0 siblings, 1 reply; 10+ messages in thread
From: Albert Comerma @ 2008-02-18 23:30 UTC (permalink / raw)
To: Antti Palosaari; +Cc: linux-dvb
[-- Attachment #1.1: Type: text/plain, Size: 12768 bytes --]
It seems ok. Could you test a scan with kaffeine instead of looking for a
specific location? And if you do so it reports signal strenght?
By the way, what does it mean moi and moikka? Hello in finish?
Albert
2008/2/18, Antti Palosaari <crope@iki.fi>:
>
> latest v4l-master + patch you give.
>
>
> regards
> Antti
>
> Albert Comerma wrote:
>
> > Uhm... that's strange, I don't have any of this cards to test, but other
> > people reported that this solution was working. Could you post the
> > dib0700_devices.c you're using to have a look?
> >
> > Albert
> >
>
> > 2008/2/18, Antti Palosaari <crope@iki.fi <mailto:crope@iki.fi>>:
>
> >
> > moi
> > It does not work for me. It says same PID-filter timeout as I have
> got
> > earlier. I don't have amplified antenna now, but I can say that all
> > other DVB-T sticks I have are working with this small antenna. It
> could
> > be that sensitivity of this hardware is bad or there is something
> wrong
> > with driver or firmware. Lets try to test it Windows to see if it is
> > working or not.
> > Logs attached.
> >
> >
> > regards
> > Antti
> >
> > Albert Comerma wrote:
> >
> > > Hey people, we already solved this problems. I submitted a patch
> > a few
> > > days ago, but I think it's not on the current sources. I send
> > again the
> > > patch. Basically it must use the same frontend description as
> > asus cards.
> > >
> > > Albert
> > >
> >
> > > 2008/2/18, Antti Palosaari <crope@iki.fi <mailto:crope@iki.fi>
>
> > <mailto:crope@iki.fi <mailto:crope@iki.fi>>>:
>
> >
> > >
> > > moikka
> > > I have also this device (express card). I haven't looked
> > inside yet, but
> > > I think there is DibCOM STK7700D (in my understanding dual
> > demod chip)
> > > and only *one* MT2266 tuner. I tried various GPIO settings
> but no
> > > luck yet.
> > > GPIO6 is for MT2266.
> > > GPIO9 and GPIO10 are for frontend.
> > >
> > > Looks like tuner goes to correct frequency because I got
> always
> > > PID-filter timeouts when tuning to correct freq. I will now
> > try to take
> > > some usb-sniffs to see configuration used. Any help is
> welcome.
> > >
> > > regards
> > > Antti
> > >
> > > Albert Comerma wrote:
> > > > Hi!, with Michel (mm-sl@ibelgique.com
> > <mailto:mm-sl@ibelgique.com>
> >
> > > <mailto:mm-sl@ibelgique.com <mailto:mm-sl@ibelgique.com>>
> > <mailto:mm-sl@ibelgique.com <mailto:mm-sl@ibelgique.com>
> >
>
> > > <mailto:mm-sl@ibelgique.com <mailto:mm-sl@ibelgique.com>>>)
> who
>
> > >
> > > > is a owner of this Yuan card we added the device to
> > > dib0700_devices, and
> > > > we got it recognized without problems. The only problem is
> > that no
> > > > channel is detected on scan on kaffeine or other
> software... I
> > > post some
> > > > dmesg. We don't know where it may be the problem... or how
> to
> > > detect it...
> > > >
> > > > usb 4-2: new high speed USB device using ehci_hcd and
> > address 6
> > > > usb 4-2: new device found, idVendor=1164, idProduct=1edc
> > > > usb 4-2: new device strings: Mfr=1, Product=2,
> SerialNumber=3
> > > > usb 4-2: Product: STK7700D
> > > > usb 4-2: Manufacturer: YUANRD
> > > > usb 4-2: SerialNumber: 0000000001
> > > > usb 4-2: configuration #1 chosen from 1 choice
> > > > dvb-usb: found a 'Yuan EC372S' in cold state, will try to
> > load a
> > > firmware
> > > > dvb-usb: downloading firmware from file
> > 'dvb-usb-dib0700-1.10.fw'
> > > > dib0700: firmware started successfully.
> > > > dvb-usb: found a 'Yuan EC372S' in warm state.
> > > > dvb-usb: will pass the complete MPEG2 transport stream to
> the
> > > software
> > > > demuxer.
> > > > DVB: registering new adapter (Yuan EC372S)
> > > > dvb-usb: no frontend was attached by 'Yuan EC372S'
> > > > dvb-usb: will pass the complete MPEG2 transport stream to
> the
> > > software
> > > > demuxer.
> > > > DVB: registering new adapter (Yuan EC372S)
> > > > DVB: registering frontend 1 (DiBcom 7000PC)...
> > > > MT2266: successfully identified
> > > > input: IR-receiver inside an USB DVB receiver as
> > /class/input/input10
> > > > dvb-usb: schedule remote query interval to 150 msecs.
> > > > dvb-usb: Yuan EC372S successfully initialized and
> connected.
> > > >
> > > >
> > >
> > > >
> > >
> >
> ------------------------------------------------------------------------
> > > >
> > > > _______________________________________________
> > > > linux-dvb mailing list
> >
> > > > linux-dvb@linuxtv.org <mailto:linux-dvb@linuxtv.org>
>
> > <mailto:linux-dvb@linuxtv.org <mailto:linux-dvb@linuxtv.org>>
>
> >
> > > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> > >
> > >
> > >
> > > --
> > > http://palosaari.fi/
> > >
> > >
> > >
> > >
> >
> ------------------------------------------------------------------------
> > >
> > > _______________________________________________
> > > linux-dvb mailing list
> > > linux-dvb@linuxtv.org <mailto:linux-dvb@linuxtv.org>
> > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> >
> >
> > --
> > http://palosaari.fi/
> >
> >
>
> > Bus 001 Device 005: ID 1164:1edc YUAN High-Tech Development Co., Ltd
> > Device Descriptor:
> > bLength 18
> > bDescriptorType 1
> > bcdUSB 2.00
> > bDeviceClass 0 (Defined at Interface level)
> > bDeviceSubClass 0
> > bDeviceProtocol 0
> > bMaxPacketSize0 64
> > idVendor 0x1164 YUAN High-Tech Development Co., Ltd
> > idProduct 0x1edc
> > bcdDevice 1.00
> > iManufacturer 1 YUANRD
> > iProduct 2 STK7700D
> > iSerial 3 0000000001
> > bNumConfigurations 1
> > Configuration Descriptor:
> > bLength 9
> > bDescriptorType 2
> > wTotalLength 46
> > bNumInterfaces 1
> > bConfigurationValue 1
> > iConfiguration 0
> > bmAttributes 0xa0
> > Remote Wakeup
> > MaxPower 500mA
> > Interface Descriptor:
> > bLength 9
> > bDescriptorType 4
> > bInterfaceNumber 0
> > bAlternateSetting 0
> > bNumEndpoints 4
> > bInterfaceClass 255 Vendor Specific Class
> > bInterfaceSubClass 0
> > bInterfaceProtocol 0
> > iInterface 0
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x01 EP 1 OUT
> > bmAttributes 2
> > Transfer Type Bulk
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0200 1x 512 bytes
> > bInterval 1
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x81 EP 1 IN
> > bmAttributes 2
> > Transfer Type Bulk
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0200 1x 512 bytes
> > bInterval 1
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x82 EP 2 IN
> > bmAttributes 2
> > Transfer Type Bulk
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0200 1x 512 bytes
> > bInterval 1
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x83 EP 3 IN
> > bmAttributes 2
> > Transfer Type Bulk
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0200 1x 512 bytes
> > bInterval 1
> > Device Qualifier (for other device speed):
> > bLength 10
> > bDescriptorType 6
> > bcdUSB 2.00
> > bDeviceClass 0 (Defined at Interface level)
> > bDeviceSubClass 0
> > bDeviceProtocol 0
> > bMaxPacketSize0 64
> > bNumConfigurations 1
> >
> > Feb 18 23:50:53 localhost kernel: usb 1-8: USB disconnect, address 5
> > Feb 18 23:50:55 localhost kernel: usb 1-8: new high speed USB device
> > using ehci_hcd and address 6
> > Feb 18 23:50:55 localhost kernel: usb 1-8: configuration #1 chosen
> > from 1 choice
> > Feb 18 23:50:55 localhost kernel: dib0700: loaded with support for 6
> > different device-types
> > Feb 18 23:50:55 localhost kernel: dvb-usb: found a 'Yuan EC372S' in
> > cold state, will try to load a firmware
> > Feb 18 23:50:55 localhost kernel: dvb-usb: downloading firmware from
> > file 'dvb-usb-dib0700-1.10.fw'
> > Feb 18 23:50:55 localhost kernel: dib0700: firmware started
> > successfully.
> > Feb 18 23:50:56 localhost kernel: dvb-usb: found a 'Yuan EC372S' in
> > warm state.
> > Feb 18 23:50:56 localhost kernel: dvb-usb: will pass the complete
> > MPEG2 transport stream to the software demuxer.
> > Feb 18 23:50:56 localhost kernel: DVB: registering new adapter (Yuan
> > EC372S)
> > Feb 18 23:50:56 localhost kernel: DVB: registering frontend 0
> > (DiBcom 7000PC)...
> > Feb 18 23:50:56 localhost kernel: MT2266: successfully identified
> > Feb 18 23:50:56 localhost kernel: dvb-usb: Yuan EC372S successfully
> > initialized and connected.
> > Feb 18 23:50:56 localhost kernel: usbcore: registered new interface
> > driver dvb_usb_dib0700
> >
> > [crope@localhost linuxtv]$ scandvb fi-Oulu
> > scanning fi-Oulu
> > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> > initial transponder 634000000 0 2 9 3 1 2 0
> > initial transponder 714000000 0 2 9 3 1 2 0
> > initial transponder 738000000 0 2 9 3 1 2 0
> > initial transponder 602000000 0 2 9 3 1 2 0
> > >>> tune to:
> >
> 634000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> > WARNING: filter timeout pid 0x0011
> > WARNING: filter timeout pid 0x0000
> > WARNING: filter timeout pid 0x0010
> > >>> tune to:
> >
> 714000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> > WARNING: filter timeout pid 0x0011
> > WARNING: filter timeout pid 0x0000
> > WARNING: filter timeout pid 0x0010
> > >>> tune to:
> >
> 738000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> > WARNING: filter timeout pid 0x0011
> > WARNING: filter timeout pid 0x0000
> > WARNING: filter timeout pid 0x0010
> > >>> tune to:
> >
> 602000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> > WARNING: filter timeout pid 0x0011
> > WARNING: filter timeout pid 0x0000
> > WARNING: filter timeout pid 0x0010
> > dumping lists (0 services)
> > Done.
> > [crope@localhost linuxtv]$
> >
> >
> >
> >
> > ------------------------------------------------------------------------
> >
> > _______________________________________________
> > linux-dvb mailing list
> > linux-dvb@linuxtv.org
> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>
> --
> http://palosaari.fi/
>
>
[-- Attachment #1.2: Type: text/html, Size: 30331 bytes --]
[-- Attachment #2: Type: text/plain, Size: 150 bytes --]
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [linux-dvb] Yuan EC372S (STK7700D based device)
2008-02-18 23:30 ` Albert Comerma
@ 2008-02-20 12:48 ` Antti Palosaari
2008-02-20 13:53 ` Albert Comerma
0 siblings, 1 reply; 10+ messages in thread
From: Antti Palosaari @ 2008-02-20 12:48 UTC (permalink / raw)
To: Albert Comerma; +Cc: linux-dvb
Albert Comerma wrote:
> It seems ok. Could you test a scan with kaffeine instead of looking for
> a specific location? And if you do so it reports signal strenght?
Kaffeine reports 100% signal strength. There must be some setting wrong
in the driver. Tuner locks to the correct frequency but signal from
uner to demodulator could be wrong and thats why PID-filter timeouts.
Even bad, I cannot snoop it in windows because I did not find all the
required Windows XP drivers for my brand new laptop. Laptop is only
computer I have ExpressCard slot...
> By the way, what does it mean moi and moikka? Hello in finish?
yes :)
regards
Antti
--
http://palosaari.fi/
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [linux-dvb] Yuan EC372S (STK7700D based device)
2008-02-20 12:48 ` Antti Palosaari
@ 2008-02-20 13:53 ` Albert Comerma
2008-02-20 15:29 ` Antti Palosaari
0 siblings, 1 reply; 10+ messages in thread
From: Albert Comerma @ 2008-02-20 13:53 UTC (permalink / raw)
To: Antti Palosaari; +Cc: linux-dvb
[-- Attachment #1.1: Type: text/plain, Size: 1992 bytes --]
moikka (I love this expression),
Michel (the person wich tested the driver, reported the same error as you).
But the solution is not trivial, I post his mail about this stuff;
This is the errors he was having (same as you);
scan -c -o zap
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
Network Name 'RTBF BE'
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x003c
WARNING: filter timeout pid 0x0038
WARNING: filter timeout pid 0x0032
WARNING: filter timeout pid 0x0820
WARNING: filter timeout pid 0x0020
WARNING: filter timeout pid 0x003a
WARNING: filter timeout pid 0x0898
WARNING: filter timeout pid 0x0034
WARNING: filter timeout pid 0x0420
dumping lists (10 services)
[0001]:0:h:0:0:0:0:1
[0002]:0:h:0:0:0:0:2
[0003]:0:h:0:0:0:0:3
[0004]:0:h:0:0:0:0:4
[000b]:0:h:0:0:0:0:11
[000c]:0:h:0:0:0:0:12
[000d]:0:h:0:0:0:55:13
[000e]:0:h:0:0:0:0:14
[000f]:0:h:0:0:0:0:15
[0010]:0:h:0:0:0:0:16
And here is what he says solved it;
Is it a coincidence, but there have been updates in kaffeine (0.8.5-35.pm)
(libxine1, libxine1-dvb version: 1.1.9-1-0.pm , for example) and since then
everything works. To be confirmed in time.
So please try if you can use this versions (or newer) and let me know.
Albert
2008/2/20, Antti Palosaari <crope@iki.fi>:
>
> Albert Comerma wrote:
> > It seems ok. Could you test a scan with kaffeine instead of looking for
> > a specific location? And if you do so it reports signal strenght?
>
>
> Kaffeine reports 100% signal strength. There must be some setting wrong
> in the driver. Tuner locks to the correct frequency but signal from
> uner to demodulator could be wrong and thats why PID-filter timeouts.
>
> Even bad, I cannot snoop it in windows because I did not find all the
> required Windows XP drivers for my brand new laptop. Laptop is only
> computer I have ExpressCard slot...
>
>
> > By the way, what does it mean moi and moikka? Hello in finish?
>
> yes :)
>
> regards
> Antti
>
> --
> http://palosaari.fi/
>
[-- Attachment #1.2: Type: text/html, Size: 2573 bytes --]
[-- Attachment #2: Type: text/plain, Size: 150 bytes --]
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [linux-dvb] Yuan EC372S (STK7700D based device)
2008-02-20 13:53 ` Albert Comerma
@ 2008-02-20 15:29 ` Antti Palosaari
2008-02-26 21:54 ` Albert Comerma
0 siblings, 1 reply; 10+ messages in thread
From: Antti Palosaari @ 2008-02-20 15:29 UTC (permalink / raw)
To: Albert Comerma; +Cc: linux-dvb
Albert Comerma wrote:
> Is it a coincidence, but there have been updates in kaffeine
> (0.8.5-35.pm <http://0.8.5-35.pm>) (libxine1, libxine1-dvb version:
> 1.1.9-1-0.pm <http://1.1.9-1-0.pm> , for example) and since then
> everything works. To be confirmed in time.
>
> So please try if you can use this versions (or newer) and let me know.
xinelib is even newer and Kaffeine version is same. I doubt that xinelib
and Kaffeine has any effect. It should lock and find PIDs even without
xinelib when using dvb-apps tools. xinelib and Kaffeine has only effect
when viewing picture.
regards
Antti
--
http://palosaari.fi/
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [linux-dvb] Yuan EC372S (STK7700D based device)
2008-02-20 15:29 ` Antti Palosaari
@ 2008-02-26 21:54 ` Albert Comerma
0 siblings, 0 replies; 10+ messages in thread
From: Albert Comerma @ 2008-02-26 21:54 UTC (permalink / raw)
To: Antti Palosaari; +Cc: linux-dvb
[-- Attachment #1.1: Type: text/plain, Size: 172 bytes --]
Are you really sure it uses the same chips?? because it's really strange
this timeout, when it seems to work in the same model... Which distribution
are you using?
Albert
[-- Attachment #1.2: Type: text/html, Size: 186 bytes --]
[-- Attachment #2: Type: text/plain, Size: 150 bytes --]
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2008-02-26 21:54 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <ea4209750801161224p6b75d7fanbdcd29e7d367802d@mail.gmail.com>
2008-02-18 18:57 ` [linux-dvb] Yuan EC372S (STK7700D based device) Antti Palosaari
2008-02-18 21:06 ` Albert Comerma
2008-02-18 22:05 ` Antti Palosaari
2008-02-18 22:24 ` Albert Comerma
2008-02-18 22:53 ` Antti Palosaari
2008-02-18 23:30 ` Albert Comerma
2008-02-20 12:48 ` Antti Palosaari
2008-02-20 13:53 ` Albert Comerma
2008-02-20 15:29 ` Antti Palosaari
2008-02-26 21:54 ` Albert Comerma
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox