* [linux-dvb] Hauppauge HVR-1300 not working
@ 2008-04-03 21:38 Jean-Louis Dupond
2008-04-04 21:41 ` Jean-Louis Dupond
0 siblings, 1 reply; 4+ messages in thread
From: Jean-Louis Dupond @ 2008-04-03 21:38 UTC (permalink / raw)
To: linux-dvb
Hello,
I bought myself a Hauppauge HVR-1300 today. To get MythTV on my Ubuntu
Hardy box.
I plugged it in, it boots perfect, drivers are getting loaded etc. BUT
i'm getting some writereg errors ...
If anybody would have an id on how I could fix this problem it would be
great!
Here is a copy/paste of the dmesg output (filtered the not needed info)
1.
[ 69.686634] Linux video capture interface: v2.00
2.
[ 69.876814] cx88/2: cx2388x MPEG-TS Driver Manager version
0.0.6 loaded
3.
[ 69.876879] cx88[0]: subsystem: 0070:9601, board: Hauppauge
WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder [card=56,autodetected]
4.
[ 69.876882] cx88[0]: TV tuner type 63, Radio tuner type -1
5.
[ 69.929361] cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
6.
[ 70.022643] tveeprom 2-0050: Hauppauge model 96019, rev D6D3,
serial# 3105276
7.
[ 70.022646] tveeprom 2-0050: MAC address is 00-0D-FE-2F-61-FC
8.
[ 70.022649] tveeprom 2-0050: tuner model is Philips FMD1216MEX
(idx 133, type 4)
9.
[ 70.022651] tveeprom 2-0050: TV standards PAL(B/G) PAL(I)
SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
10.
[ 70.022653] tveeprom 2-0050: audio processor is CX882 (idx 33)
11.
[ 70.022655] tveeprom 2-0050: decoder processor is CX882 (idx 25)
12.
[ 70.022656] tveeprom 2-0050: has radio, has IR receiver, has IR
transmitter
13.
[ 70.022658] cx88[0]: hauppauge eeprom: model=96019
14.
[ 70.022752] cx88[0]/2: cx2388x 8802 Driver Manager
15.
[ 70.023095] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
16.
[ 70.023105] ACPI: PCI Interrupt 0000:02:08.2[A] -> Link [APC3]
-> GSI 18 (level, low) -> IRQ 18
17.
[ 70.023113] cx88[0]/2: found at 0000:02:08.2, rev: 5, irq: 18,
latency: 32, mmio: 0xfb000000
18.
[ 70.023151] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [APC3]
-> GSI 18 (level, low) -> IRQ 18
19.
[ 70.023157] cx88[0]/0: found at 0000:02:08.0, rev: 5, irq: 18,
latency: 32, mmio: 0xfa000000
20.
[ 70.314384] wm8775 2-001b: chip found @ 0x36 (cx88[0])
21.
[ 70.318446] cx88[0]/0: registered device video0 [v4l2]
22.
[ 70.318462] cx88[0]/0: registered device vbi0
23.
[ 70.318475] cx88[0]/0: registered device radio0
24.
[ 70.386235] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 20
25.
[ 70.386240] ACPI: PCI Interrupt 0000:00:0e.1[B] -> Link [AAZA]
-> GSI 20 (level, low) -> IRQ 20
26.
[ 70.386311] PCI: Setting latency timer of device 0000:00:0e.1 to 64
27.
[ 70.476456] cx88/2: cx2388x dvb driver version 0.0.6 loaded
28.
[ 70.476460] cx88/2: registering cx8802 driver, type: dvb
access: shared
29.
[ 70.476463] cx88[0]/2: subsystem: 0070:9601, board: Hauppauge
WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder [card=56]
30.
[ 70.476466] cx88[0]/2: cx2388x based DVB/ATSC card
31.
[ 70.500678] phy0: Selected rate control algorithm 'simple'
32.
[ 70.588346] input: PC Speaker as
/devices/platform/pcspkr/input/input6
33.
[ 70.907743] DVB: registering new adapter (cx88[0])
34.
[ 70.907748] DVB: registering frontend 0 (Conexant CX22702 DVB-T)...
35.
[ 71.083319] cx2388x blackbird driver version 0.0.6 loaded
36.
[ 71.083323] cx88/2: registering cx8802 driver, type: blackbird
access: shared
37.
[ 71.083326] cx88[0]/2: subsystem: 0070:9601, board: Hauppauge
WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder [card=56]
38.
[ 71.083330] cx88[0]/2: cx23416 based mpeg encoder (blackbird
reference design)
39.
[ 71.084521] cx88[0]/2: registered device video1 [mpeg]
40.
41.
[ 78.788278] cx22702_readreg: readreg error (ret == -121)
42.
[ 78.788913] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x00, ret == -121)
43.
[ 78.789494] cx22702_readreg: readreg error (ret == -121)
44.
[ 78.790066] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x01, ret == -121)
45.
[ 78.800513] cx22702_readreg: readreg error (ret == -121)
46.
[ 78.801139] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x00, ret == -121)
47.
[ 78.801717] cx22702_readreg: readreg error (ret == -121)
48.
[ 78.802302] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x01, ret == -121)
49.
[ 78.810709] cx22702_readreg: readreg error (ret == -121)
50.
[ 78.811329] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x00, ret == -121)
51.
[ 78.811907] cx22702_readreg: readreg error (ret == -121)
52.
[ 78.812465] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x01, ret == -121)
53.
[ 78.818835] cx22702_readreg: readreg error (ret == -121)
54.
[ 78.819455] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x00, ret == -121)
55.
[ 78.820035] cx22702_readreg: readreg error (ret == -121)
56.
[ 78.820595] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x01, ret == -121)
57.
[ 78.839544] cx88[0]/2-bb: Firmware and/or mailbox pointer not
initialized or corrupted
58.
[ 81.527690] cx88[0]/2-bb: Firmware upload successful.
59.
[ 81.535759] cx88[0]/2-bb: Firmware version is 0x02060039
60.
[ 81.598038] cx88[0]/2-bb: VIDIOC_TRY_FMT: w: 720, h: 480, f: 4
61.
62.
[ 95.317798] cx22702_writereg: writereg error (reg == 0x00, val
== 0x02, ret == -121)
63.
[ 95.323842] cx22702_writereg: writereg error (reg == 0x00, val
== 0x00, ret == -121)
64.
[ 95.324262] cx22702_writereg: writereg error (reg == 0x0b, val
== 0x06, ret == -121)
65.
[ 95.324667] cx22702_writereg: writereg error (reg == 0x09, val
== 0x01, ret == -121)
66.
[ 95.324986] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x41, ret == -121)
67.
[ 95.325310] cx22702_writereg: writereg error (reg == 0x16, val
== 0x32, ret == -121)
68.
[ 95.326737] cx22702_writereg: writereg error (reg == 0x20, val
== 0x0a, ret == -121)
69.
[ 95.327090] cx22702_writereg: writereg error (reg == 0x21, val
== 0x17, ret == -121)
70.
[ 95.327291] cx22702_writereg: writereg error (reg == 0x24, val
== 0x3e, ret == -121)
71.
[ 95.327490] cx22702_writereg: writereg error (reg == 0x26, val
== 0xff, ret == -121)
72.
[ 95.327689] cx22702_writereg: writereg error (reg == 0x27, val
== 0x10, ret == -121)
73.
[ 95.327888] cx22702_writereg: writereg error (reg == 0x28, val
== 0x00, ret == -121)
74.
[ 95.328087] cx22702_writereg: writereg error (reg == 0x29, val
== 0x00, ret == -121)
75.
[ 95.328286] cx22702_writereg: writereg error (reg == 0x2a, val
== 0x10, ret == -121)
76.
[ 95.328487] cx22702_writereg: writereg error (reg == 0x2b, val
== 0x00, ret == -121)
77.
[ 95.328691] cx22702_writereg: writereg error (reg == 0x2c, val
== 0x10, ret == -121)
78.
[ 95.328889] cx22702_writereg: writereg error (reg == 0x2d, val
== 0x00, ret == -121)
79.
[ 95.329088] cx22702_writereg: writereg error (reg == 0x48, val
== 0xd4, ret == -121)
80.
[ 95.329287] cx22702_writereg: writereg error (reg == 0x49, val
== 0x56, ret == -121)
81.
[ 95.329487] cx22702_writereg: writereg error (reg == 0x6b, val
== 0x1e, ret == -121)
82.
[ 95.329685] cx22702_writereg: writereg error (reg == 0xc8, val
== 0x02, ret == -121)
83.
[ 95.329884] cx22702_writereg: writereg error (reg == 0xf9, val
== 0x00, ret == -121)
84.
[ 95.330083] cx22702_writereg: writereg error (reg == 0xfa, val
== 0x00, ret == -121)
85.
[ 95.330285] cx22702_writereg: writereg error (reg == 0xfb, val
== 0x00, ret == -121)
86.
[ 95.331619] cx22702_writereg: writereg error (reg == 0xfc, val
== 0x00, ret == -121)
87.
[ 95.331941] cx22702_writereg: writereg error (reg == 0xfd, val
== 0x00, ret == -121)
88.
[ 95.333750] cx22702_writereg: writereg error (reg == 0xf8, val
== 0x02, ret == -121)
89.
[ 95.333949] cx22702_readreg: readreg error (ret == -121)
90.
[ 95.334148] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x01, ret == -121)
91.
[ 95.334347] cx22702_readreg: readreg error (ret == -121)
92.
[ 95.334546] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x00, ret == -121)
93.
[ 95.334941] cx22702_readreg: readreg error (ret == -121)
94.
[ 95.335140] cx22702_writereg: writereg error (reg == 0x0d, val
== 0x01, ret == -121)
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [linux-dvb] Hauppauge HVR-1300 not working
2008-04-03 21:38 [linux-dvb] Hauppauge HVR-1300 not working Jean-Louis Dupond
@ 2008-04-04 21:41 ` Jean-Louis Dupond
2008-04-05 13:47 ` Jean-Louis Dupond
0 siblings, 1 reply; 4+ messages in thread
From: Jean-Louis Dupond @ 2008-04-04 21:41 UTC (permalink / raw)
To: linux-dvb
Hello,
I tried tons of different kernel versions, latest v4l hg etc ... nothing
works ... all are giving me more or less the same error:
http://pastebin.com/f10c1160b here is another dmesg output (2.6.25-rc8
with latest hg).
I hope this is getting fixxed soon :)
Jean-Louis Dupond schreef:
> Hello,
>
> I bought myself a Hauppauge HVR-1300 today. To get MythTV on my Ubuntu
> Hardy box.
> I plugged it in, it boots perfect, drivers are getting loaded etc. BUT
> i'm getting some writereg errors ...
>
> If anybody would have an id on how I could fix this problem it would be
> great!
>
> Here is a copy/paste of the dmesg output (filtered the not needed info)
>
> 1.
> [ 69.686634] Linux video capture interface: v2.00
> 2.
> [ 69.876814] cx88/2: cx2388x MPEG-TS Driver Manager version
> 0.0.6 loaded
> 3.
> [ 69.876879] cx88[0]: subsystem: 0070:9601, board: Hauppauge
> WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder [card=56,autodetected]
> 4.
> [ 69.876882] cx88[0]: TV tuner type 63, Radio tuner type -1
> 5.
> [ 69.929361] cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
> 6.
> [ 70.022643] tveeprom 2-0050: Hauppauge model 96019, rev D6D3,
> serial# 3105276
> 7.
> [ 70.022646] tveeprom 2-0050: MAC address is 00-0D-FE-2F-61-FC
> 8.
> [ 70.022649] tveeprom 2-0050: tuner model is Philips FMD1216MEX
> (idx 133, type 4)
> 9.
> [ 70.022651] tveeprom 2-0050: TV standards PAL(B/G) PAL(I)
> SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
> 10.
> [ 70.022653] tveeprom 2-0050: audio processor is CX882 (idx 33)
> 11.
> [ 70.022655] tveeprom 2-0050: decoder processor is CX882 (idx 25)
> 12.
> [ 70.022656] tveeprom 2-0050: has radio, has IR receiver, has IR
> transmitter
> 13.
> [ 70.022658] cx88[0]: hauppauge eeprom: model=96019
> 14.
> [ 70.022752] cx88[0]/2: cx2388x 8802 Driver Manager
> 15.
> [ 70.023095] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
> 16.
> [ 70.023105] ACPI: PCI Interrupt 0000:02:08.2[A] -> Link [APC3]
> -> GSI 18 (level, low) -> IRQ 18
> 17.
> [ 70.023113] cx88[0]/2: found at 0000:02:08.2, rev: 5, irq: 18,
> latency: 32, mmio: 0xfb000000
> 18.
> [ 70.023151] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [APC3]
> -> GSI 18 (level, low) -> IRQ 18
> 19.
> [ 70.023157] cx88[0]/0: found at 0000:02:08.0, rev: 5, irq: 18,
> latency: 32, mmio: 0xfa000000
> 20.
> [ 70.314384] wm8775 2-001b: chip found @ 0x36 (cx88[0])
> 21.
> [ 70.318446] cx88[0]/0: registered device video0 [v4l2]
> 22.
> [ 70.318462] cx88[0]/0: registered device vbi0
> 23.
> [ 70.318475] cx88[0]/0: registered device radio0
> 24.
> [ 70.386235] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 20
> 25.
> [ 70.386240] ACPI: PCI Interrupt 0000:00:0e.1[B] -> Link [AAZA]
> -> GSI 20 (level, low) -> IRQ 20
> 26.
> [ 70.386311] PCI: Setting latency timer of device 0000:00:0e.1 to 64
> 27.
> [ 70.476456] cx88/2: cx2388x dvb driver version 0.0.6 loaded
> 28.
> [ 70.476460] cx88/2: registering cx8802 driver, type: dvb
> access: shared
> 29.
> [ 70.476463] cx88[0]/2: subsystem: 0070:9601, board: Hauppauge
> WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder [card=56]
> 30.
> [ 70.476466] cx88[0]/2: cx2388x based DVB/ATSC card
> 31.
> [ 70.500678] phy0: Selected rate control algorithm 'simple'
> 32.
> [ 70.588346] input: PC Speaker as
> /devices/platform/pcspkr/input/input6
> 33.
> [ 70.907743] DVB: registering new adapter (cx88[0])
> 34.
> [ 70.907748] DVB: registering frontend 0 (Conexant CX22702 DVB-T)...
> 35.
> [ 71.083319] cx2388x blackbird driver version 0.0.6 loaded
> 36.
> [ 71.083323] cx88/2: registering cx8802 driver, type: blackbird
> access: shared
> 37.
> [ 71.083326] cx88[0]/2: subsystem: 0070:9601, board: Hauppauge
> WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder [card=56]
> 38.
> [ 71.083330] cx88[0]/2: cx23416 based mpeg encoder (blackbird
> reference design)
> 39.
> [ 71.084521] cx88[0]/2: registered device video1 [mpeg]
> 40.
>
> 41.
> [ 78.788278] cx22702_readreg: readreg error (ret == -121)
> 42.
> [ 78.788913] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x00, ret == -121)
> 43.
> [ 78.789494] cx22702_readreg: readreg error (ret == -121)
> 44.
> [ 78.790066] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x01, ret == -121)
> 45.
> [ 78.800513] cx22702_readreg: readreg error (ret == -121)
> 46.
> [ 78.801139] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x00, ret == -121)
> 47.
> [ 78.801717] cx22702_readreg: readreg error (ret == -121)
> 48.
> [ 78.802302] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x01, ret == -121)
> 49.
> [ 78.810709] cx22702_readreg: readreg error (ret == -121)
> 50.
> [ 78.811329] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x00, ret == -121)
> 51.
> [ 78.811907] cx22702_readreg: readreg error (ret == -121)
> 52.
> [ 78.812465] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x01, ret == -121)
> 53.
> [ 78.818835] cx22702_readreg: readreg error (ret == -121)
> 54.
> [ 78.819455] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x00, ret == -121)
> 55.
> [ 78.820035] cx22702_readreg: readreg error (ret == -121)
> 56.
> [ 78.820595] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x01, ret == -121)
> 57.
> [ 78.839544] cx88[0]/2-bb: Firmware and/or mailbox pointer not
> initialized or corrupted
> 58.
> [ 81.527690] cx88[0]/2-bb: Firmware upload successful.
> 59.
> [ 81.535759] cx88[0]/2-bb: Firmware version is 0x02060039
> 60.
> [ 81.598038] cx88[0]/2-bb: VIDIOC_TRY_FMT: w: 720, h: 480, f: 4
> 61.
>
> 62.
> [ 95.317798] cx22702_writereg: writereg error (reg == 0x00, val
> == 0x02, ret == -121)
> 63.
> [ 95.323842] cx22702_writereg: writereg error (reg == 0x00, val
> == 0x00, ret == -121)
> 64.
> [ 95.324262] cx22702_writereg: writereg error (reg == 0x0b, val
> == 0x06, ret == -121)
> 65.
> [ 95.324667] cx22702_writereg: writereg error (reg == 0x09, val
> == 0x01, ret == -121)
> 66.
> [ 95.324986] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x41, ret == -121)
> 67.
> [ 95.325310] cx22702_writereg: writereg error (reg == 0x16, val
> == 0x32, ret == -121)
> 68.
> [ 95.326737] cx22702_writereg: writereg error (reg == 0x20, val
> == 0x0a, ret == -121)
> 69.
> [ 95.327090] cx22702_writereg: writereg error (reg == 0x21, val
> == 0x17, ret == -121)
> 70.
> [ 95.327291] cx22702_writereg: writereg error (reg == 0x24, val
> == 0x3e, ret == -121)
> 71.
> [ 95.327490] cx22702_writereg: writereg error (reg == 0x26, val
> == 0xff, ret == -121)
> 72.
> [ 95.327689] cx22702_writereg: writereg error (reg == 0x27, val
> == 0x10, ret == -121)
> 73.
> [ 95.327888] cx22702_writereg: writereg error (reg == 0x28, val
> == 0x00, ret == -121)
> 74.
> [ 95.328087] cx22702_writereg: writereg error (reg == 0x29, val
> == 0x00, ret == -121)
> 75.
> [ 95.328286] cx22702_writereg: writereg error (reg == 0x2a, val
> == 0x10, ret == -121)
> 76.
> [ 95.328487] cx22702_writereg: writereg error (reg == 0x2b, val
> == 0x00, ret == -121)
> 77.
> [ 95.328691] cx22702_writereg: writereg error (reg == 0x2c, val
> == 0x10, ret == -121)
> 78.
> [ 95.328889] cx22702_writereg: writereg error (reg == 0x2d, val
> == 0x00, ret == -121)
> 79.
> [ 95.329088] cx22702_writereg: writereg error (reg == 0x48, val
> == 0xd4, ret == -121)
> 80.
> [ 95.329287] cx22702_writereg: writereg error (reg == 0x49, val
> == 0x56, ret == -121)
> 81.
> [ 95.329487] cx22702_writereg: writereg error (reg == 0x6b, val
> == 0x1e, ret == -121)
> 82.
> [ 95.329685] cx22702_writereg: writereg error (reg == 0xc8, val
> == 0x02, ret == -121)
> 83.
> [ 95.329884] cx22702_writereg: writereg error (reg == 0xf9, val
> == 0x00, ret == -121)
> 84.
> [ 95.330083] cx22702_writereg: writereg error (reg == 0xfa, val
> == 0x00, ret == -121)
> 85.
> [ 95.330285] cx22702_writereg: writereg error (reg == 0xfb, val
> == 0x00, ret == -121)
> 86.
> [ 95.331619] cx22702_writereg: writereg error (reg == 0xfc, val
> == 0x00, ret == -121)
> 87.
> [ 95.331941] cx22702_writereg: writereg error (reg == 0xfd, val
> == 0x00, ret == -121)
> 88.
> [ 95.333750] cx22702_writereg: writereg error (reg == 0xf8, val
> == 0x02, ret == -121)
> 89.
> [ 95.333949] cx22702_readreg: readreg error (ret == -121)
> 90.
> [ 95.334148] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x01, ret == -121)
> 91.
> [ 95.334347] cx22702_readreg: readreg error (ret == -121)
> 92.
> [ 95.334546] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x00, ret == -121)
> 93.
> [ 95.334941] cx22702_readreg: readreg error (ret == -121)
> 94.
> [ 95.335140] cx22702_writereg: writereg error (reg == 0x0d, val
> == 0x01, ret == -121)
>
>
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [linux-dvb] Hauppauge HVR-1300 not working
2008-04-04 21:41 ` Jean-Louis Dupond
@ 2008-04-05 13:47 ` Jean-Louis Dupond
2008-04-05 13:56 ` Steven Toth
0 siblings, 1 reply; 4+ messages in thread
From: Jean-Louis Dupond @ 2008-04-05 13:47 UTC (permalink / raw)
To: linux-dvb
Seems like stopping HAL & reloading the modules fixxes it ...
Jean-Louis Dupond schreef:
> Hello,
>
> I tried tons of different kernel versions, latest v4l hg etc ... nothing
> works ... all are giving me more or less the same error:
>
> http://pastebin.com/f10c1160b here is another dmesg output (2.6.25-rc8
> with latest hg).
>
> I hope this is getting fixxed soon :)
>
> Jean-Louis Dupond schreef:
>
>> Hello,
>>
>> I bought myself a Hauppauge HVR-1300 today. To get MythTV on my Ubuntu
>> Hardy box.
>> I plugged it in, it boots perfect, drivers are getting loaded etc. BUT
>> i'm getting some writereg errors ...
>>
>> If anybody would have an id on how I could fix this problem it would be
>> great!
>>
>> Here is a copy/paste of the dmesg output (filtered the not needed info)
>>
>> 1.
>> [ 69.686634] Linux video capture interface: v2.00
>> 2.
>> [ 69.876814] cx88/2: cx2388x MPEG-TS Driver Manager version
>> 0.0.6 loaded
>> 3.
>> [ 69.876879] cx88[0]: subsystem: 0070:9601, board: Hauppauge
>> WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder [card=56,autodetected]
>> 4.
>> [ 69.876882] cx88[0]: TV tuner type 63, Radio tuner type -1
>> 5.
>> [ 69.929361] cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
>> 6.
>> [ 70.022643] tveeprom 2-0050: Hauppauge model 96019, rev D6D3,
>> serial# 3105276
>> 7.
>> [ 70.022646] tveeprom 2-0050: MAC address is 00-0D-FE-2F-61-FC
>> 8.
>> [ 70.022649] tveeprom 2-0050: tuner model is Philips FMD1216MEX
>> (idx 133, type 4)
>> 9.
>> [ 70.022651] tveeprom 2-0050: TV standards PAL(B/G) PAL(I)
>> SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
>> 10.
>> [ 70.022653] tveeprom 2-0050: audio processor is CX882 (idx 33)
>> 11.
>> [ 70.022655] tveeprom 2-0050: decoder processor is CX882 (idx 25)
>> 12.
>> [ 70.022656] tveeprom 2-0050: has radio, has IR receiver, has IR
>> transmitter
>> 13.
>> [ 70.022658] cx88[0]: hauppauge eeprom: model=96019
>> 14.
>> [ 70.022752] cx88[0]/2: cx2388x 8802 Driver Manager
>> 15.
>> [ 70.023095] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
>> 16.
>> [ 70.023105] ACPI: PCI Interrupt 0000:02:08.2[A] -> Link [APC3]
>> -> GSI 18 (level, low) -> IRQ 18
>> 17.
>> [ 70.023113] cx88[0]/2: found at 0000:02:08.2, rev: 5, irq: 18,
>> latency: 32, mmio: 0xfb000000
>> 18.
>> [ 70.023151] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [APC3]
>> -> GSI 18 (level, low) -> IRQ 18
>> 19.
>> [ 70.023157] cx88[0]/0: found at 0000:02:08.0, rev: 5, irq: 18,
>> latency: 32, mmio: 0xfa000000
>> 20.
>> [ 70.314384] wm8775 2-001b: chip found @ 0x36 (cx88[0])
>> 21.
>> [ 70.318446] cx88[0]/0: registered device video0 [v4l2]
>> 22.
>> [ 70.318462] cx88[0]/0: registered device vbi0
>> 23.
>> [ 70.318475] cx88[0]/0: registered device radio0
>> 24.
>> [ 70.386235] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 20
>> 25.
>> [ 70.386240] ACPI: PCI Interrupt 0000:00:0e.1[B] -> Link [AAZA]
>> -> GSI 20 (level, low) -> IRQ 20
>> 26.
>> [ 70.386311] PCI: Setting latency timer of device 0000:00:0e.1 to 64
>> 27.
>> [ 70.476456] cx88/2: cx2388x dvb driver version 0.0.6 loaded
>> 28.
>> [ 70.476460] cx88/2: registering cx8802 driver, type: dvb
>> access: shared
>> 29.
>> [ 70.476463] cx88[0]/2: subsystem: 0070:9601, board: Hauppauge
>> WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder [card=56]
>> 30.
>> [ 70.476466] cx88[0]/2: cx2388x based DVB/ATSC card
>> 31.
>> [ 70.500678] phy0: Selected rate control algorithm 'simple'
>> 32.
>> [ 70.588346] input: PC Speaker as
>> /devices/platform/pcspkr/input/input6
>> 33.
>> [ 70.907743] DVB: registering new adapter (cx88[0])
>> 34.
>> [ 70.907748] DVB: registering frontend 0 (Conexant CX22702 DVB-T)...
>> 35.
>> [ 71.083319] cx2388x blackbird driver version 0.0.6 loaded
>> 36.
>> [ 71.083323] cx88/2: registering cx8802 driver, type: blackbird
>> access: shared
>> 37.
>> [ 71.083326] cx88[0]/2: subsystem: 0070:9601, board: Hauppauge
>> WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder [card=56]
>> 38.
>> [ 71.083330] cx88[0]/2: cx23416 based mpeg encoder (blackbird
>> reference design)
>> 39.
>> [ 71.084521] cx88[0]/2: registered device video1 [mpeg]
>> 40.
>>
>> 41.
>> [ 78.788278] cx22702_readreg: readreg error (ret == -121)
>> 42.
>> [ 78.788913] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x00, ret == -121)
>> 43.
>> [ 78.789494] cx22702_readreg: readreg error (ret == -121)
>> 44.
>> [ 78.790066] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x01, ret == -121)
>> 45.
>> [ 78.800513] cx22702_readreg: readreg error (ret == -121)
>> 46.
>> [ 78.801139] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x00, ret == -121)
>> 47.
>> [ 78.801717] cx22702_readreg: readreg error (ret == -121)
>> 48.
>> [ 78.802302] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x01, ret == -121)
>> 49.
>> [ 78.810709] cx22702_readreg: readreg error (ret == -121)
>> 50.
>> [ 78.811329] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x00, ret == -121)
>> 51.
>> [ 78.811907] cx22702_readreg: readreg error (ret == -121)
>> 52.
>> [ 78.812465] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x01, ret == -121)
>> 53.
>> [ 78.818835] cx22702_readreg: readreg error (ret == -121)
>> 54.
>> [ 78.819455] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x00, ret == -121)
>> 55.
>> [ 78.820035] cx22702_readreg: readreg error (ret == -121)
>> 56.
>> [ 78.820595] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x01, ret == -121)
>> 57.
>> [ 78.839544] cx88[0]/2-bb: Firmware and/or mailbox pointer not
>> initialized or corrupted
>> 58.
>> [ 81.527690] cx88[0]/2-bb: Firmware upload successful.
>> 59.
>> [ 81.535759] cx88[0]/2-bb: Firmware version is 0x02060039
>> 60.
>> [ 81.598038] cx88[0]/2-bb: VIDIOC_TRY_FMT: w: 720, h: 480, f: 4
>> 61.
>>
>> 62.
>> [ 95.317798] cx22702_writereg: writereg error (reg == 0x00, val
>> == 0x02, ret == -121)
>> 63.
>> [ 95.323842] cx22702_writereg: writereg error (reg == 0x00, val
>> == 0x00, ret == -121)
>> 64.
>> [ 95.324262] cx22702_writereg: writereg error (reg == 0x0b, val
>> == 0x06, ret == -121)
>> 65.
>> [ 95.324667] cx22702_writereg: writereg error (reg == 0x09, val
>> == 0x01, ret == -121)
>> 66.
>> [ 95.324986] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x41, ret == -121)
>> 67.
>> [ 95.325310] cx22702_writereg: writereg error (reg == 0x16, val
>> == 0x32, ret == -121)
>> 68.
>> [ 95.326737] cx22702_writereg: writereg error (reg == 0x20, val
>> == 0x0a, ret == -121)
>> 69.
>> [ 95.327090] cx22702_writereg: writereg error (reg == 0x21, val
>> == 0x17, ret == -121)
>> 70.
>> [ 95.327291] cx22702_writereg: writereg error (reg == 0x24, val
>> == 0x3e, ret == -121)
>> 71.
>> [ 95.327490] cx22702_writereg: writereg error (reg == 0x26, val
>> == 0xff, ret == -121)
>> 72.
>> [ 95.327689] cx22702_writereg: writereg error (reg == 0x27, val
>> == 0x10, ret == -121)
>> 73.
>> [ 95.327888] cx22702_writereg: writereg error (reg == 0x28, val
>> == 0x00, ret == -121)
>> 74.
>> [ 95.328087] cx22702_writereg: writereg error (reg == 0x29, val
>> == 0x00, ret == -121)
>> 75.
>> [ 95.328286] cx22702_writereg: writereg error (reg == 0x2a, val
>> == 0x10, ret == -121)
>> 76.
>> [ 95.328487] cx22702_writereg: writereg error (reg == 0x2b, val
>> == 0x00, ret == -121)
>> 77.
>> [ 95.328691] cx22702_writereg: writereg error (reg == 0x2c, val
>> == 0x10, ret == -121)
>> 78.
>> [ 95.328889] cx22702_writereg: writereg error (reg == 0x2d, val
>> == 0x00, ret == -121)
>> 79.
>> [ 95.329088] cx22702_writereg: writereg error (reg == 0x48, val
>> == 0xd4, ret == -121)
>> 80.
>> [ 95.329287] cx22702_writereg: writereg error (reg == 0x49, val
>> == 0x56, ret == -121)
>> 81.
>> [ 95.329487] cx22702_writereg: writereg error (reg == 0x6b, val
>> == 0x1e, ret == -121)
>> 82.
>> [ 95.329685] cx22702_writereg: writereg error (reg == 0xc8, val
>> == 0x02, ret == -121)
>> 83.
>> [ 95.329884] cx22702_writereg: writereg error (reg == 0xf9, val
>> == 0x00, ret == -121)
>> 84.
>> [ 95.330083] cx22702_writereg: writereg error (reg == 0xfa, val
>> == 0x00, ret == -121)
>> 85.
>> [ 95.330285] cx22702_writereg: writereg error (reg == 0xfb, val
>> == 0x00, ret == -121)
>> 86.
>> [ 95.331619] cx22702_writereg: writereg error (reg == 0xfc, val
>> == 0x00, ret == -121)
>> 87.
>> [ 95.331941] cx22702_writereg: writereg error (reg == 0xfd, val
>> == 0x00, ret == -121)
>> 88.
>> [ 95.333750] cx22702_writereg: writereg error (reg == 0xf8, val
>> == 0x02, ret == -121)
>> 89.
>> [ 95.333949] cx22702_readreg: readreg error (ret == -121)
>> 90.
>> [ 95.334148] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x01, ret == -121)
>> 91.
>> [ 95.334347] cx22702_readreg: readreg error (ret == -121)
>> 92.
>> [ 95.334546] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x00, ret == -121)
>> 93.
>> [ 95.334941] cx22702_readreg: readreg error (ret == -121)
>> 94.
>> [ 95.335140] cx22702_writereg: writereg error (reg == 0x0d, val
>> == 0x01, ret == -121)
>>
>>
>>
>> _______________________________________________
>> linux-dvb mailing list
>> linux-dvb@linuxtv.org
>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>>
>>
>>
>
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [linux-dvb] Hauppauge HVR-1300 not working
2008-04-05 13:47 ` Jean-Louis Dupond
@ 2008-04-05 13:56 ` Steven Toth
0 siblings, 0 replies; 4+ messages in thread
From: Steven Toth @ 2008-04-05 13:56 UTC (permalink / raw)
To: Jean-Louis Dupond; +Cc: linux-dvb
Jean-Louis Dupond wrote:
> Seems like stopping HAL & reloading the modules fixxes it ...
>
> Jean-Louis Dupond schreef:
>> Hello,
>>
>> I tried tons of different kernel versions, latest v4l hg etc ... nothing
>> works ... all are giving me more or less the same error:
>>
>> http://pastebin.com/f10c1160b here is another dmesg output (2.6.25-rc8
>> with latest hg).
>>
>> I hope this is getting fixxed soon :)
I know what's broken, but I don't know why. I also don't know why it's
platform specific.
I'm looking at possible solutions now.
- Steve
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2008-04-05 13:57 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-04-03 21:38 [linux-dvb] Hauppauge HVR-1300 not working Jean-Louis Dupond
2008-04-04 21:41 ` Jean-Louis Dupond
2008-04-05 13:47 ` Jean-Louis Dupond
2008-04-05 13:56 ` Steven Toth
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox