Re: [linux-dvb] Hauppauge HVR-1700 Support

[Steven Toth <stoth@linuxtv.org>]

Torben Viets wrote:
> Steven Toth wrote:
>> Torben Viets wrote:
>>> Hello,
>>>
>>> I've got it: http://pastebin.com/f50f33096
>>>
>>> the trick was to compile the kernel (now linux-2.6.25-git13) with:
>>>
>>> CONFIG_I2C_DEBUG_CORE=y
>>> CONFIG_I2C_DEBUG_ALGO=y
>>> CONFIG_I2C_DEBUG_BUS=y
>>> CONFIG_I2C_DEBUG_CHIP=y
>>>
>>> I hope you've got an idea, i updated my bios (afters this my RAM 
>>> doesn't work anymore), installed a new Ubuntu Linux hardy (8.04)...
>>>
>>> One last question when will the firmware be loaded and why there is 
>>> no hotplug tool in ubuntu, or is it in the kernel?
>>>
>>> greetings
>>> Torben
>>>
>>>
>>> Steven Toth wrote:
>>>> Torben Viets wrote:
>>>>> Steven Toth wrote:
>>>>>> Torben Viets wrote:
>>>>>>> Steven Toth wrote:
>>>>>>>> Torben Viets wrote:
>>>>>>>>> Hello,
>>>>>>>>>
>>>>>>>>> thanks for the quick reply.
>>>>>>>>>
>>>>>>>>> Steven Toth wrote:
>>>>>>>>>> Torben Viets wrote:
>>>>>>>>>>> Hello,
>>>>>>>>>>>
>>>>>>>>>>> I have a Hauppauge HVR-1700 PCI Express, I have read all 
>>>>>>>>>>> posts about
>>>>>>>>>>> this card here, but I didn't get it working, how does it work?
>>>>>>>>>>
>>>>>>>>>> It's working fine for me on a stock 7.10 ubuntu install.
>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> Kernel: linux-2.6.25-git10
>>>>>>>>>>>
>>>>>>>>>>> Firmware-Files:
>>>>>>>>>>> ls -al /lib/firmware/2.6.25-git10/
>>>>>>>>>>> total 416
>>>>>>>>>>> drwxr-xr-x 2 root root     91 Apr 27 16:27 .
>>>>>>>>>>> drwxr-xr-x 3 root root     25 Apr 27 16:26 ..
>>>>>>>>>>> -rw-r--r-- 1 root root  24878 Apr 27 16:27 
>>>>>>>>>>> dvb-fe-tda10048-1.0.fw
>>>>>>>>>>> -r--r--r-- 1 root root  16382 Apr 27 16:27 
>>>>>>>>>>> v4l-cx23885-avcore-01.fw
>>>>>>>>>>> -r--r--r-- 1 root root 376836 Apr 27 16:26 v4l-cx23885-enc.fw
>>>>>>>>>>>
>>>>>>>>>>> The modules I use are from the actual v4l-dvb hg, if I type 
>>>>>>>>>>> make load,
>>>>>>>>>>> the only thing I get is a /dev/video0, but I have no picture 
>>>>>>>>>>> with xawtv...
>>>>>>>>>>
>>>>>>>>>> /dev/video doesn't work, it's not supported.
>>>>>>>>>>
>>>>>>>>> Are there any plans to support it?
>>>>>>>>
>>>>>>>>
>>>>>>>> No immediate plans.
>>>>>>>>
>>>>>>>>
>>>>>>>>>> You should aim to use the dvb-apps tools (tzap, scan) and 
>>>>>>>>>> mplayer as example tools, or MythTV as an app.
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> The DVB doesn't work at all, I have no /dev/dvb*, here is my 
>>>>>>>>>>> dmesg:
>>>>>>>>>>>
>>>>>>>>>>> cx23885 driver version 0.0.1 loaded
>>>>>>>>>>> ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 24 (level, low) -> 
>>>>>>>>>>> IRQ 24
>>>>>>>>>>> CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge 
>>>>>>>>>>> WinTV-HVR1700
>>>>>>>>>>> [card=8,autodetected]
>>>>>>>>>>> cx23885[0]: i2c bus 0 registered
>>>>>>>>>>> cx23885[0]: i2c bus 1 registered
>>>>>>>>>>> cx23885[0]: i2c bus 2 registered
>>>>>>>>>>> tveeprom 0-0050: Huh, no eeprom present (err=-5)?
>>>>>>>>>>> tveeprom 0-0050: Encountered bad packet header [00].
>>>>>>>>>>> Corrupt or not a Hauppauge
>>>>>>>>>>> eeprom.
>>>>>>>>>>> cx23885[0]: warning: unknown hauppauge model #0
>>>>>>>>>>> cx23885[0]: hauppauge eeprom: model=0
>>>>>>>>>>> cx23885[0]: cx23885 based dvb card
>>>>>>>>>>> tda10048_readreg: readreg error (ret == -5)
>>>>>>>>>>> cx23885[0]: frontend initialization failed
>>>>>>>>>>> cx23885_dvb_register() dvb_register failed err = -1
>>>>>>>>>>> cx23885_dev_setup() Failed to register dvb on VID_C
>>>>>>>>>>> cx23885_dev_checkrevision() New hardware revision found 0x0
>>>>>>>>>>> cx23885_dev_checkrevision() Hardware revision unknown 0x0
>>>>>>>>>>> cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 24, 
>>>>>>>>>>> latency: 0, mmio:
>>>>>>>>>>> 0xfe800000
>>>>>>>>>>
>>>>>>>>>> This looks bad, it looks like i2c is broken badly, so that the 
>>>>>>>>>> eeprom isn't detected and the demodulator isn't found during 
>>>>>>>>>> attach. This is the reason why your missing /dev/dvb/adapterX/
>>>>>>>>>>
>>>>>>>>>> No idea why. Try loading the cx23885 with debug=5 and report 
>>>>>>>>>> any log messages here - on this mailing list.
>>>>>>>>> here ist the debug=5 output
>>>>>>>>>
>>>>>>>>> cx23885[0]/0: cx23885_dev_setup() Memory configured for PCIe 
>>>>>>>>> bridge type 885
>>>>>>>>> cx23885[0]/0: cx23885_init_tsport(portno=2)
>>>>>>>>> CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge 
>>>>>>>>> WinTV-HVR1700 [card=8,autodetected]
>>>>>>>>> cx23885[0]/0: cx23885_pci_quirks()
>>>>>>>>> cx23885[0]/0: cx23885_dev_setup() tuner_type = 0x0 tuner_addr = 
>>>>>>>>> 0x0
>>>>>>>>> cx23885[0]/0: cx23885_dev_setup() radio_type = 0x0 radio_addr = 
>>>>>>>>> 0x0
>>>>>>>>> cx23885[0]/0: cx23885_reset()
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel 
>>>>>>>>> [VID A]
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000107b0 <- 
>>>>>>>>> 0x00000040
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000107c0 <- 
>>>>>>>>> 0x00000b80
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000107d0 <- 
>>>>>>>>> 0x000016c0
>>>>>>>>> cx23885[0]/0: [bridge 885] sram setup VID A: bpl=2880 lines=3
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch2]
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel 
>>>>>>>>> [TS1 B]
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010400 <- 
>>>>>>>>> 0x00005000
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010410 <- 
>>>>>>>>> 0x000052f0
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010420 <- 
>>>>>>>>> 0x000055e0
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010430 <- 
>>>>>>>>> 0x000058d0
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010440 <- 
>>>>>>>>> 0x00005bc0
>>>>>>>>> cx23885[0]/0: [bridge 885] sram setup TS1 B: bpl=752 lines=5
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch4]
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch5]
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel 
>>>>>>>>> [TS2 C]
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000108d0 <- 
>>>>>>>>> 0x00006000
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000108e0 <- 
>>>>>>>>> 0x000062f0
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x000108f0 <- 
>>>>>>>>> 0x000065e0
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010900 <- 
>>>>>>>>> 0x000068d0
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() 0x00010910 <- 
>>>>>>>>> 0x00006bc0
>>>>>>>>> cx23885[0]/0: [bridge 885] sram setup TS2 C: bpl=752 lines=5
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch7]
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch8]
>>>>>>>>> cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch9]
>>>>>>>>> cx23885[0]: i2c bus 0 registered
>>>>>>>>> cx23885[0]: i2c bus 1 registered
>>>>>>>>> cx23885[0]: i2c bus 2 registered
>>>>>>>>
>>>>>>>> Everything looks fine up to this point, then i2c looks bad.
>>>>>>>>
>>>>>>>> Can you try again with modprobe cx23885 i2c_scan=1 and post the 
>>>>>>>> output again? (Output will be large - feel free to use 
>>>>>>>> pastebin.com and post the URL here).
>>>>>>>
>>>>>>> hmm, output doesn't change with it. here is a lsmod plus a 
>>>>>>> complete dmesg, is some module missing?
>>>>>>>
>>>>>>> http://pastebin.com/f4f9b58ed
>>>>>>>
>>>>>>
>>>>>> The module option isn't active.
>>>>>>
>>>>>> Unload the cx23885 module (and any dependencies) then try modprobe 
>>>>>> i2c_scan=1
>>>>>>
>>>>>> When the module option is set correctly, you'll see a lot of extra 
>>>>>> debug messages.
>>>>>>
>>>>>> - Steve
>>>>>>
>>>>>>
>>>>>
>>>>> hmm, I've unload all modules that sounds interesting, but there is 
>>>>> no more output: http://pastebin.com/f157a3978
>>>>
>>>> Hmm. No idea. i2c_scan is working for me and various other people. 
>>>> Something is wrong with your environment and I don't know what.
>>>>
>>>> The only time I've seen i2c_scan output not work, is when i2c_scan 
>>>> is not passed as a module parameter.
>>>>
>>>> Unload all modules, then use lsmod to ensure cx23885.ko is not loaded.
>>>> Then, modprobe cx23885 debug=5 i2c_scan=1
>>>>
>>>> If that doesn't show i2c device scanning traffic then I'm stumped.
>>>>
>>>> - Steve
>>>>
>>>
>>
>> Thanks for the feedback. This is odd, it looks like either I2C isn;t 
>> working at all, or it's working partially for device 0x44. I think I'm 
>> tempted to believe it's not working at all.
>>
>> The firmware gets loaded by the cx25840 module (if required), the 
>> module is requested on the fly. But, that doesn't explain the missing 
>> eeprom errors.
>>
>> Does this board work under windows?
>>
>> - Steve
>>
> hmm, never tested under windows, i' windows free ;) but i will install 
> Windows now and will try wether it works....

Try a -stable linux kernel first, linux-2.6.25-git10 might be broken.

- Steve


_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb