* [linux-dvb] Hauppauge WinTV-HVR-1200 @ 2008-04-27 21:27 RISCH Gilles 2008-04-27 22:48 ` Michael Krufky 2008-04-28 15:48 ` Steven Toth 0 siblings, 2 replies; 6+ messages in thread From: RISCH Gilles @ 2008-04-27 21:27 UTC (permalink / raw) To: linux-dvb Hello, the Hauppauge WinTV-HVR-1200 is now listened as a supported card in the wiki. What I'm missing are some instructions how to get the card working. Does a such document already exist? Regards Gilles _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] Hauppauge WinTV-HVR-1200 2008-04-27 21:27 [linux-dvb] Hauppauge WinTV-HVR-1200 RISCH Gilles @ 2008-04-27 22:48 ` Michael Krufky 2008-04-28 15:48 ` Steven Toth 1 sibling, 0 replies; 6+ messages in thread From: Michael Krufky @ 2008-04-27 22:48 UTC (permalink / raw) To: RISCH Gilles; +Cc: linux-dvb RISCH Gilles wrote: > Hello, > > the Hauppauge WinTV-HVR-1200 is now listened as a supported card in the wiki. > What I'm missing are some instructions how to get the card working. Does a > such document already exist? This card is supported in the master v4l-dvb repository, hosted on linuxtv.org: http://linuxtv.org/hg/v4l-dvb For a howto: http://linuxtv.org/repo Good Luck. -Mike _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] Hauppauge WinTV-HVR-1200 2008-04-27 21:27 [linux-dvb] Hauppauge WinTV-HVR-1200 RISCH Gilles 2008-04-27 22:48 ` Michael Krufky @ 2008-04-28 15:48 ` Steven Toth 2008-05-01 22:38 ` RISCH Gilles 1 sibling, 1 reply; 6+ messages in thread From: Steven Toth @ 2008-04-28 15:48 UTC (permalink / raw) To: RISCH Gilles; +Cc: linux-dvb RISCH Gilles wrote: > Hello, > > the Hauppauge WinTV-HVR-1200 is now listened as a supported card in the wiki. > What I'm missing are some instructions how to get the card working. Does a > such document already exist? No, but feel free to update the wiki so other benefit from your work. 1. Build and install the modules, as per the wiki instructions. 2. Reboot and your done, as per the wiki instructions. 3. Scan for channels or use an existing channels.conf, as per the wiki instructions. 4. Update the HVR1200 wiki page. Regards, Steve _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] Hauppauge WinTV-HVR-1200 2008-04-28 15:48 ` Steven Toth @ 2008-05-01 22:38 ` RISCH Gilles 2008-05-02 0:47 ` Michael Krufky 0 siblings, 1 reply; 6+ messages in thread From: RISCH Gilles @ 2008-05-01 22:38 UTC (permalink / raw) To: Steven Toth; +Cc: linux-dvb Hello, my card is running, I've added some lines to the wiki: http://www.linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-1200 can someone review / try it out Regards On Monday 28 April 2008 17:48:46 Steven Toth wrote: > RISCH Gilles wrote: > > Hello, > > > > the Hauppauge WinTV-HVR-1200 is now listened as a supported card in the > > wiki. What I'm missing are some instructions how to get the card working. > > Does a such document already exist? > > No, but feel free to update the wiki so other benefit from your work. > > 1. Build and install the modules, as per the wiki instructions. > 2. Reboot and your done, as per the wiki instructions. > 3. Scan for channels or use an existing channels.conf, as per the wiki > instructions. > 4. Update the HVR1200 wiki page. > > Regards, > > Steve _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] Hauppauge WinTV-HVR-1200 2008-05-01 22:38 ` RISCH Gilles @ 2008-05-02 0:47 ` Michael Krufky [not found] ` <200805021311.18036.roodemol@cjbous.net> 0 siblings, 1 reply; 6+ messages in thread From: Michael Krufky @ 2008-05-02 0:47 UTC (permalink / raw) To: RISCH Gilles; +Cc: linux-dvb >> RISCH Gilles wrote: >>> Hello, >>> > On Monday 28 April 2008 17:48:46 Steven Toth wrote: >>> the Hauppauge WinTV-HVR-1200 is now listened as a supported card in the >>> wiki. What I'm missing are some instructions how to get the card working. >>> Does a such document already exist? >> No, but feel free to update the wiki so other benefit from your work. >> >> 1. Build and install the modules, as per the wiki instructions. >> 2. Reboot and your done, as per the wiki instructions. >> 3. Scan for channels or use an existing channels.conf, as per the wiki >> instructions. >> 4. Update the HVR1200 wiki page. >> >> Regards, >> >> Steve RISCH Gilles wrote: > Hello, > > my card is running, I've added some lines to the wiki: > http://www.linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-1200 > > can someone review / try it out > > Regards > Please do not top-quote. Replies should appear below the quoted text. Your wiki entry says, " 5. add this line to /etc/modules.d/dvb: options cx23885 card=7 " Why? Does the cx23885 driver not autodetect your board? The HVR1200 has a subsystem ID that should allow the driver to autodetect your board. If your board is not autodetected, it means one of two things: 1) The subsystem id of your card is missing, and we can simply add that for you to avoid the need for module option. 2) For one reason or another, the device may be reading the eeprom incorrectly, causing the subid not to show properly. This is unlikely, but I have seen it happen in certain motherboards using cx23885 based products. Please test without the module option -- your board should be properly autodetected. If this is not the case, please send in your full dmesg output. Regards, Mike Krufky _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
[parent not found: <200805021311.18036.roodemol@cjbous.net>]
* Re: [linux-dvb] Hauppauge WinTV-HVR-1200 [not found] ` <200805021311.18036.roodemol@cjbous.net> @ 2008-05-02 12:33 ` Michael Krufky 0 siblings, 0 replies; 6+ messages in thread From: Michael Krufky @ 2008-05-02 12:33 UTC (permalink / raw) To: RISCH Gilles; +Cc: Linux DVB Mailing List RISCH Gilles wrote: > On Friday 02 May 2008 02:47:17 you wrote: > >>>> RISCH Gilles wrote: >>>> >>>>> Hello, >>>>> >>> On Monday 28 April 2008 17:48:46 Steven Toth wrote: >>> >>>>> the Hauppauge WinTV-HVR-1200 is now listened as a supported card in the >>>>> wiki. What I'm missing are some instructions how to get the card >>>>> working. Does a such document already exist? >>>>> >>>> No, but feel free to update the wiki so other benefit from your work. >>>> >>>> 1. Build and install the modules, as per the wiki instructions. >>>> 2. Reboot and your done, as per the wiki instructions. >>>> 3. Scan for channels or use an existing channels.conf, as per the wiki >>>> instructions. >>>> 4. Update the HVR1200 wiki page. >>>> >>>> Regards, >>>> >>>> Steve >>>> >> RISCH Gilles wrote: >> >>> Hello, >>> >>> my card is running, I've added some lines to the wiki: >>> http://www.linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-1200 >>> >>> can someone review / try it out >>> >>> Regards >>> >> Please do not top-quote. Replies should appear below the quoted text. >> >> Your wiki entry says, >> >> " >> 5. add this line to /etc/modules.d/dvb: >> options cx23885 card=7 >> " >> >> Why? Does the cx23885 driver not autodetect your board? >> >> The HVR1200 has a subsystem ID that should allow the driver to autodetect >> your board. If your board is not autodetected, it means one of two things: >> >> 1) The subsystem id of your card is missing, and we can simply add that for >> you to avoid the need for module option. >> >> 2) For one reason or another, the device may be reading the eeprom >> incorrectly, causing the subid not to show properly. This is unlikely, but >> I have seen it happen in certain motherboards using cx23885 based products. >> >> Please test without the module option -- your board should be properly >> autodetected. If this is not the case, please send in your full dmesg >> output. >> >> Regards, >> >> Mike Krufky >> > > Hello, > > It does not work whitout the entry in /etc/modules.d/dvb and I don't know if > it is due to point 1 or 2, but I estimate that it is point 1 due to the > warning in dmesg: > > [ 44.041711] cx23885 driver version 0.0.1 loaded > [ 44.042028] ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16 > [ 44.042030] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [APC6] -> GSI 16 > (level, low) -> IRQ 16 > [ 44.042043] CORE cx23885[0]: subsystem: 0070:71d3, board: Hauppauge > WinTV-HVR1200 [card=7,insmod option] > [ 44.190051] cx23885[0]: i2c bus 0 registered > [ 44.190066] cx23885[0]: i2c bus 1 registered > [ 44.190077] cx23885[0]: i2c bus 2 registered > [ 44.215621] tveeprom 2-0050: Hauppauge model 71949, rev H2E9, serial# > 2812545 > [ 44.215623] tveeprom 2-0050: MAC address is 00-0D-FE-2A-EA-81 > [ 44.215625] tveeprom 2-0050: tuner model is Philips 18271_8295 (idx 149, > type 54) > [ 44.215627] tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') > PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) > [ 44.215628] tveeprom 2-0050: audio processor is CX23885 (idx 39) > [ 44.215630] tveeprom 2-0050: decoder processor is CX23885 (idx 33) > [ 44.215631] tveeprom 2-0050: has no radio, has no IR receiver, has no IR > transmitter > [ 44.215633] cx23885[0]: warning: unknown hauppauge model #71949 > [ 44.215634] cx23885[0]: hauppauge eeprom: model=71949 > [ 44.218910] cx23885[0]: cx23885 based dvb card > [ 44.269356] tda829x 3-0042: type set to tda8295 > [ 44.315028] tda18271 3-0060: creating new instance > [ 44.348447] TDA18271HD/C1 detected @ 3-0060 > [ 44.480440] phy0: Selected rate control algorithm 'simple' > [ 44.543974] usbcore: registered new interface driver rt73usb > [ 44.925226] NET: Registered protocol family 17 > [ 45.394593] DVB: registering new adapter (cx23885[0]) > [ 45.394597] DVB: registering frontend 0 (NXP TDA10048HN DVB-T)... > [ 45.394795] cx23885_dev_checkrevision() Hardware revision = 0xb0 > [ 45.394801] cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 16, latency: > 0, mmio: 0xfd800000 > > The card was preinstalled in a HP Pavilion 9050 and under Windows it's shown > as Hauppauge WinTV-HVR-1200. > > Regards, Gilles Thanks -- I'll update the PCI subids list today. -Mike _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2008-05-02 12:34 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-04-27 21:27 [linux-dvb] Hauppauge WinTV-HVR-1200 RISCH Gilles
2008-04-27 22:48 ` Michael Krufky
2008-04-28 15:48 ` Steven Toth
2008-05-01 22:38 ` RISCH Gilles
2008-05-02 0:47 ` Michael Krufky
[not found] ` <200805021311.18036.roodemol@cjbous.net>
2008-05-02 12:33 ` Michael Krufky
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox