* My Cinema-P7131 Hybrid (spider cable)
@ 2008-05-16 8:27 pw.marcus
2008-05-16 11:36 ` hermann pitton
0 siblings, 1 reply; 7+ messages in thread
From: pw.marcus @ 2008-05-16 8:27 UTC (permalink / raw)
To: video4linux-list
Hello,
I would like to know if the spider cable (S-video, coaxial video, RCA
audio L-R) works with this card, or is possible, because, I can watch
DVB-T on the computer, but when I plug this cable from the card to a TV
(peritel), I don't get anything on the TV.
My system:
-------------------
intel dual core processor
Intel motherboard (i945 built-in graphic card)
Debian unstable 64 bits
kernel 2.6.25-3 (with the original v4l driver of the kernel)
Thanks for help, cheers
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: My Cinema-P7131 Hybrid (spider cable)
2008-05-16 8:27 My Cinema-P7131 Hybrid (spider cable) pw.marcus
@ 2008-05-16 11:36 ` hermann pitton
2008-05-16 17:08 ` pw.marcus
0 siblings, 1 reply; 7+ messages in thread
From: hermann pitton @ 2008-05-16 11:36 UTC (permalink / raw)
To: pw.marcus; +Cc: video4linux-list
Hi,
Am Freitag, den 16.05.2008, 10:27 +0200 schrieb pw.marcus:
> Hello,
>
> I would like to know if the spider cable (S-video, coaxial video, RCA
> audio L-R) works with this card, or is possible, because, I can watch
> DVB-T on the computer, but when I plug this cable from the card to a TV
> (peritel), I don't get anything on the TV.
>
> My system:
> -------------------
> intel dual core processor
> Intel motherboard (i945 built-in graphic card)
> Debian unstable 64 bits
> kernel 2.6.25-3 (with the original v4l driver of the kernel)
>
> Thanks for help, cheers
>
if I understand you right, you seem to think that the card has output on
this "spider cable", but it are all INPUTS.
You need TV-OUT from your graphics card or something else capable to
display on TV.
Cheers,
Hermann
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: My Cinema-P7131 Hybrid (spider cable)
2008-05-16 11:36 ` hermann pitton
@ 2008-05-16 17:08 ` pw.marcus
2008-05-16 19:41 ` hermann pitton
0 siblings, 1 reply; 7+ messages in thread
From: pw.marcus @ 2008-05-16 17:08 UTC (permalink / raw)
To: hermann pitton, video4linux-list
Hermann thank you for your answer, ok, I see, I should have thought
about it before ! so much the worst !
One second question :
How are configured the 2 main outputs of the card ?
Upside output for DVB-T & radio ?
Downside output for analog TV ?
Is it right ?
Cheers
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: My Cinema-P7131 Hybrid (spider cable)
2008-05-16 17:08 ` pw.marcus
@ 2008-05-16 19:41 ` hermann pitton
2008-05-18 10:03 ` pw.marcus
0 siblings, 1 reply; 7+ messages in thread
From: hermann pitton @ 2008-05-16 19:41 UTC (permalink / raw)
To: pw.marcus; +Cc: video4linux-list
Am Freitag, den 16.05.2008, 19:08 +0200 schrieb pw.marcus:
> Hermann thank you for your answer, ok, I see, I should have thought
> about it before ! so much the worst !
>
> One second question :
>
> How are configured the 2 main outputs of the card ?
>
> Upside output for DVB-T & radio ?
> Downside output for analog TV ?
>
> Is it right ?
>
> Cheers
>
Yes, this is right.
You can force card=81 if you want to have DVB-T and analog TV on the
lower connector and only radio on the upper, but the remote is not
enabled on that card then.
Take care, you might get trouble on analog TV SECAM_L NICAM stereo
detection from 2.6.25 onwards. Mauro disabled valid PAL and SECAM sub
standards, which were introduced to be user selectable for the reason
that audio carrier autodetection is not always successfully, especially
not for SECAM_L NICAM on the second carrier, but also for others.
Until 2.6.24 one could force "secam=L" by an saa7134 insmod option (try
"modinfo saa7134") or select it from the application. On saa7135 and
saa7131e also forcing it with "audio_ddep=0x10" for Secam_L/L' was
possible. This all looks pretty much broken currently, but I can't test
on that known critical stuff and Hartmut, who spent two weekends with a
signal generator to come to viable solutions for all after years, might
be pleased as well ;)
Cheers,
Hermann
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2008-05-19 7:55 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-05-16 8:27 My Cinema-P7131 Hybrid (spider cable) pw.marcus
2008-05-16 11:36 ` hermann pitton
2008-05-16 17:08 ` pw.marcus
2008-05-16 19:41 ` hermann pitton
2008-05-18 10:03 ` pw.marcus
2008-05-18 23:30 ` hermann pitton
2008-05-19 8:04 ` pw.marcus
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox