* [linux-dvb] Terratec Cinergy Piranha @ 2008-06-06 7:15 Nicolas Christener 2008-06-06 9:17 ` Antti Palosaari 2008-06-06 9:20 ` Dennis Noordsij 0 siblings, 2 replies; 6+ messages in thread From: Nicolas Christener @ 2008-06-06 7:15 UTC (permalink / raw) To: linux-dvb Hello according to [1] i should contact this list, because I own a currently unsupported DVB-T USB device and want to support development :) The device I got is labeled 'Terratec Cinergy Piranha'. output of `dmesg': kernel: hub 5-0:1.0: unable to enumerate USB device on port 5 kernel: usb 3-1: new full speed USB device using uhci_hcd and address 6 kernel: usb 3-1: configuration #1 chosen from 1 choice kernel: usb 3-1: New USB device found, idVendor=187f, idProduct=0010 kernel: usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 kernel: usb 3-1: Product: SMS 1000 kernel: usb 3-1: Manufacturer: Siano Although I can probably not help to write code for this device I'd be happy, if I could help in any other way to get this device supported by linux. [1] http://linuxtv.org/wiki/index.php/DVB-T_USB_Devices kind regards Nicolas _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] Terratec Cinergy Piranha 2008-06-06 7:15 [linux-dvb] Terratec Cinergy Piranha Nicolas Christener @ 2008-06-06 9:17 ` Antti Palosaari 2008-06-06 9:20 ` Dennis Noordsij 1 sibling, 0 replies; 6+ messages in thread From: Antti Palosaari @ 2008-06-06 9:17 UTC (permalink / raw) To: Nicolas Christener; +Cc: linux-dvb Nicolas Christener wrote: > The device I got is labeled 'Terratec Cinergy Piranha'. > kernel: usb 3-1: Manufacturer: Siano Look messages from list archive during last week. There is some discussion under the thread "Driver TerraTec Piranha functional, need some advice to finish up". regards Antti -- http://palosaari.fi/ _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] Terratec Cinergy Piranha 2008-06-06 7:15 [linux-dvb] Terratec Cinergy Piranha Nicolas Christener 2008-06-06 9:17 ` Antti Palosaari @ 2008-06-06 9:20 ` Dennis Noordsij 2008-06-06 14:38 ` Nicolas Christener 1 sibling, 1 reply; 6+ messages in thread From: Dennis Noordsij @ 2008-06-06 9:20 UTC (permalink / raw) To: Nicolas Christener; +Cc: linux-dvb Nicolas Christener schreef: > Hello > according to [1] i should contact this list, because I own a currently > unsupported DVB-T USB device and want to support development :) > The device I got is labeled 'Terratec Cinergy Piranha'. > > output of `dmesg': > kernel: hub 5-0:1.0: unable to enumerate USB device on port 5 > kernel: usb 3-1: new full speed USB device using uhci_hcd and address 6 > kernel: usb 3-1: configuration #1 chosen from 1 choice > kernel: usb 3-1: New USB device found, idVendor=187f, idProduct=0010 > kernel: usb 3-1: New USB device strings: Mfr=1, Product=2, > SerialNumber=0 > kernel: usb 3-1: Product: SMS 1000 > kernel: usb 3-1: Manufacturer: Siano > > Although I can probably not help to write code for this device I'd be > happy, if I could help in any other way to get this device supported by > linux. > > [1] http://linuxtv.org/wiki/index.php/DVB-T_USB_Devices > > kind regards > Nicolas Hi Nicolas, You're in luck :-) That device works very well. The driver is not in the official tree (yet) so if you would like to use it you will need to compile it yourself, there are some instructions on linuxtv.org, and use the following tree: http://linuxtv.org/hg/~mkrufky/siano You will also need to take the firmware file "SMS100x_Dvbt.inp" (from the installation CD or windows, or download the drivers from terratec.net) and copy it to your \lib\firmware or \lib\firmware\`uname -r` as "dvbt_stellar_usb.inp". I hope those instructions make sense :-) Dennis _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] Terratec Cinergy Piranha 2008-06-06 9:20 ` Dennis Noordsij @ 2008-06-06 14:38 ` Nicolas Christener 2008-06-06 14:59 ` Dennis Noordsij 0 siblings, 1 reply; 6+ messages in thread From: Nicolas Christener @ 2008-06-06 14:38 UTC (permalink / raw) To: Dennis Noordsij; +Cc: linux-dvb Hello thanks very much for your fast response! Am Freitag, den 06.06.2008, 11:20 +0200 schrieb Dennis Noordsij: [...] > You're in luck :-) That device works very well. *w00h00* sounds good :) > The driver is not in the official tree (yet) so if you would like to use > it you will need to compile it yourself, [...] > You will also need to take the firmware file "SMS100x_Dvbt.inp" (from > the installation CD or windows, or download the drivers from > terratec.net) and copy it to your \lib\firmware or \lib\firmware\`uname > -r` as "dvbt_stellar_usb.inp". > > I hope those instructions make sense :-) thank you very much four your explanation. This is what I get: [root@oipunk:/lib/firmware]# uname -a Linux oipunk 2.6.25.4-paldo1-x86 #1 SMP PREEMPT Fri May 16 14:52:58 CEST 2008 i686 GNU/Linux [root@oipunk:/lib/firmware]# lsmod | grep sms1xxx sms1xxx 25560 0 dvb_core 80512 1 sms1xxx firmware_class 10496 4 sms1xxx,microcode,iwl3945,pcmcia [root@oipunk:/lib/firmware]# modinfo sms1xxx filename: /lib/modules/2.6.25.4-paldo1-x86/kernel/drivers/media/dvb/siano/sms1xxx.ko license: GPL author: Anatoly Greenblatt,,, (anatolyg@siano-ms.com) description: smscore alias: usb:v187Fp0200d*dc*dsc*dp*ic*isc*ip* alias: usb:v187Fp0100d*dc*dsc*dp*ic*isc*ip* alias: usb:v187Fp0010d*dc*dsc*dp*ic*isc*ip* depends: dvb-core,firmware_class vermagic: 2.6.25.4-paldo1-x86 SMP preempt mod_unload PENTIUMIII parm: adapter_nr:DVB adapter numbers (array of short) parm: default_mode:default firmware id (device mode) (int) [root@oipunk:/lib/firmware]# ls -la *.inp -r-xr-xr-x 1 root root 40324 2008-06-06 14:34 dvbh_stellar_usb.inp -r-xr-xr-x 1 root root 38144 2008-06-06 14:28 dvbt_stellar_usb.inp [root@oipunk:/var/log]# dmesg [...] usb 3-1: new full speed USB device using uhci_hcd and address 43 usb 3-1: configuration #1 chosen from 1 choice smsusb_probe 0 endpoint 0 81 02 64 endpoint 1 02 02 64 smscore_register_device allocated 50 buffers smscore_register_device device ed48cf00 created smsusb1_detectmode: 1 "SMS DVBH Receiver" smscore_onresponse no client (00000000) or error (-16), type:698 dstid:0 DVB: registering new adapter (Siano Digital Receiver) DVB: registering frontend 0 (Siano Mobile Digital SMS10xx)... smscore_register_client f6972800 693 0 smsdvb_hotplug success smscore_start_device device ed48cf00 started, rc 0 smsusb_init_device device f6973000 created usb 3-1: New USB device found, idVendor=187f, idProduct=0100 usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 3-1: Product: SMS DVBH Receiver usb 3-1: Manufacturer: Siano Mobile Silicon smsusb_onresponse error, urb status -84, 0 bytes smsusb_onresponse error, urb status -84, 0 bytes smsusb_onresponse error, urb status -84, 0 bytes smsusb_onresponse error, urb status -84, 0 bytes smsusb_onresponse error, urb status -84, 0 bytes smsusb_onresponse error, urb status -84, 0 bytes smsusb_onresponse error, urb status -84, 0 bytes smsusb_onresponse error, urb status -84, 0 bytes smsusb_onresponse error, urb status -84, 0 bytes smsusb_onresponse error, urb status -84, 0 bytes usb 3-1: USB disconnect, address 43 smscore_unregister_client f6972800 693 smscore_unregister_device freed 50 buffers smscore_unregister_device device ed48cf00 destroyed smsusb_term_device device f6973000 destroyed Unfortunately I do not get a device within /dev Am I doing something wrong? Or is there just something missing in my installation? I would very much appreciate any help. kind regards Nicolas _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] Terratec Cinergy Piranha 2008-06-06 14:38 ` Nicolas Christener @ 2008-06-06 14:59 ` Dennis Noordsij 2008-06-06 17:58 ` Nicolas Christener 0 siblings, 1 reply; 6+ messages in thread From: Dennis Noordsij @ 2008-06-06 14:59 UTC (permalink / raw) To: Nicolas Christener; +Cc: linux-dvb > thank you very much four your explanation. This is what I get: > Unfortunately I do not get a device within /dev > Am I doing something wrong? Or is there just something missing in my > installation? Ah, yes. Sorry forgot to mention one part. As you can tell from the log, the default mode is DVB-H. use: modprobe sms1xxx default_mode=0 or change the default_mode variable in the file smscoreapi.c and rebuild the driver. Dennis _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] Terratec Cinergy Piranha 2008-06-06 14:59 ` Dennis Noordsij @ 2008-06-06 17:58 ` Nicolas Christener 0 siblings, 0 replies; 6+ messages in thread From: Nicolas Christener @ 2008-06-06 17:58 UTC (permalink / raw) To: Dennis Noordsij; +Cc: linux-dvb Hi Dennis, hello list Am Freitag, den 06.06.2008, 16:59 +0200 schrieb Dennis Noordsij: [...] > Ah, yes. Sorry forgot to mention one part. As you can tell from the log, > the default mode is DVB-H. > > use: modprobe sms1xxx default_mode=0 ah yep this does the trick :) Now I got the devices: [nicolas@oipunk:/dev/dvb]$ find . . ./adapter0 ./adapter0/frontend0 ./adapter0/dvr0 ./adapter0/demux0 and `dmesg' looks good too. Thanks very much! However there is something left and I'm not sure, if it is a driver issue. Most probably the driver is OK and I'm doing something wrong ;) As far as I know, I now need to create a channels.conf file for xine, mplayer... Thats what I did: [nicolas@oipunk:~/temp/tv/dvb-apps-9311c900f746/util/scan]$ ./scan dvb-t/ch-All scanning dvb-t/ch-All using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 482000000 0 5 9 1 1 3 0 [...] >>> tune to: 482000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_5_6:FEC_AUTO:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE WARNING: >>> tuning failed!!! >>> tune to: 482000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_5_6:FEC_AUTO:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE (tuning failed) WARNING: >>> tuning failed!!! >>> tune to: 514000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_5_6:FEC_AUTO:QAM_16:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_4:HIERARCHY_NONE WARNING: >>> tuning failed!!! [...] ERROR: initial tuning failed dumping lists (0 services) Done. I hope this is not a stupid newbie problem, but until now I couldn't find a solution. I also tried the `w_scan' utility which couldn't find any channels either. I would very much appreciate any help. kind regards Nicolas _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2008-06-06 17:58 UTC | newest] Thread overview: 6+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2008-06-06 7:15 [linux-dvb] Terratec Cinergy Piranha Nicolas Christener 2008-06-06 9:17 ` Antti Palosaari 2008-06-06 9:20 ` Dennis Noordsij 2008-06-06 14:38 ` Nicolas Christener 2008-06-06 14:59 ` Dennis Noordsij 2008-06-06 17:58 ` Nicolas Christener
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox