From: "postfix@au-79.de" <postfix@au-79.de>
To: linux-dvb@linuxtv.org
Subject: Re: [linux-dvb] unknown dvbt device 1ae7:0381 Xtensions 380U
Date: Tue, 15 Jul 2008 23:00:53 +0200 [thread overview]
Message-ID: <487D1005.8000208@au-79.de> (raw)
Hello Antti,
this was the solution. It works now quite fine. Thanks a lot for your
fast and very good work.
here again the dmesg:
usb 1-6.1: new high speed USB device using ehci_hcd and address 10
usb 1-6.1: configuration #1 chosen from 1 choice
usb 1-6.1: New USB device found, idVendor=1ae7, idProduct=0381
usb 1-6.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-6.1: Product: DVB-T 2
usb 1-6.1: Manufacturer: Afatech
af9015_usb_probe: interface:0
af9015_read_config: IR mode:4
af9015_read_config: TS mode:0
af9015_read_config: [0] xtal:2 set adc_clock:28000
af9015_read_config: [0] IF1:36125
af9015_read_config: [0] MT2060 IF1:5888
af9015_read_config: [0] tuner id:134
af9015_identify_state: reply:01
dvb-usb: found a 'Xtensions XD-380' in cold state, will try to load a
firmware
dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw'
af9015_download_firmware:
usbcore: registered new interface driver dvb_usb_af9015
usb 1-6.1: USB disconnect, address 10
af9015_usb_device_exit:
dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
usb 1-6.1: new high speed USB device using ehci_hcd and address 11
usb 1-6.1: configuration #1 chosen from 1 choice
af9015_usb_probe: interface:0
af9015_read_config: IR mode:4
af9015_read_config: TS mode:0
af9015_read_config: [0] xtal:2 set adc_clock:28000
af9015_read_config: [0] IF1:36125
af9015_read_config: [0] MT2060 IF1:5888
af9015_read_config: [0] tuner id:134
af9015_identify_state: reply:02
dvb-usb: found a 'Xtensions XD-380' in warm state.
i2c-adapter i2c-3: SMBus Quick command not supported, can't probe for chips
dvb-usb: will pass the complete MPEG2 transport stream to the software
demuxer.
DVB: registering new adapter (Xtensions XD-380)
af9015_af9013_frontend_attach: init I2C
af9015_i2c_init:
i2c-adapter i2c-4: SMBus Quick command not supported, can't probe for chips
00: 2b f0 9b 0b 00 00 00 00 e7 1a 81 03 00 02 01 02
10: 00 80 00 fa fa 10 40 ef 04 30 31 30 31 30 32 30
20: 32 30 37 30 30 30 30 31 ff ff ff ff ff ff ff ff
30: 00 00 3a 01 00 08 02 00 1d 8d 00 17 86 ff ff ff
40: ff ff ff ff ff 08 02 00 1d 8d c4 04 82 ff ff ff
50: ff ff ff ff ff 26 00 00 04 03 09 04 10 03 41 00
60: 66 00 61 00 74 00 65 00 63 00 68 00 10 03 44 00
70: 56 00 42 00 2d 00 54 00 20 00 32 00 20 03 30 00
80: 31 00 30 00 31 00 30 00 31 00 30 00 31 00 30 00
90: 36 00 30 00 30 00 30 00 30 00 31 00 00 ff ff ff
a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
af9013: chip version:1 ROM version:1.0
af9013: firmware version:4.65.0
DVB: registering frontend 0 (Afatech AF9013 DVB-T)...
af9015_tuner_attach:
Quantek QT1010 successfully identified.
dvb-usb: Xtensions XD-380 successfully initialized and connected.
af9015_init:
af9015_init_endpoint: USB speed:3
af9015_download_ir_table:
usb 1-6.1: New USB device found, idVendor=1ae7, idProduct=0381
usb 1-6.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-6.1: Product: DVB-T 2
usb 1-6.1: Manufacturer: Afatech
af9015_pid_filter_ctrl: onoff:0
If you want me to try any patches etc. please let me know. As far as I
see, this device has no IR-interface.
regards
Robert
Antti Palosaari schrieb:
> postfix@au-79.de wrote:
>> Hello Antti,
>>
>> thanks for your work. I tryed your patched files and according to
>> dmesg, it looks like a good initialisation. But after init there are
>> endless failures like:
>> dvb-usb: error while querying for an remote control event.
>> af9015: af9015_rw_udev: sending failed: -110 (8/0)
>> af9015: af9015_rw_udev: receiving failed: -110
>
> I have no idea what IR-mode is 0x04 but hopefully it will start working
> now when remote polling is disabled.
> Please test again.
>
> regards
> Antti
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
next reply other threads:[~2008-07-15 21:01 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-07-15 21:00 postfix [this message]
-- strict thread matches above, loose matches on Subject: below --
2008-07-15 6:43 [linux-dvb] unknown dvbt device 1ae7:0381 Xtensions 380U Robert Goldner
2008-07-15 11:11 ` Antti Palosaari
2008-07-15 16:37 ` Antti Palosaari
2008-07-15 19:58 ` postfix
2008-07-15 20:35 ` Antti Palosaari
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=487D1005.8000208@au-79.de \
--to=postfix@au-79.de \
--cc=linux-dvb@linuxtv.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox