* Geniatech UTV3
@ 2008-09-16 17:09 eli hamels
2008-09-16 17:33 ` Markus Rechberger
2008-09-16 17:40 ` Devin Heitmueller
0 siblings, 2 replies; 4+ messages in thread
From: eli hamels @ 2008-09-16 17:09 UTC (permalink / raw)
To: video4linux-list
Hi all,
I have a Geniatech UTV3 usb tv box that didn't worked on linux.
After taking the device apart, I found following components
* FM24C02 -> EEPROM
* EM2860 -> USB Video Capture Device
* SAA7113H -> Video input processor
* TOA9801 -> Demodulator and FM-PLL detector (for sound)
* HCF4052 -> Analog multiplexer (for switching sound between TV and AV)
* TNF8337-DFD -> TV tuner/reciever
After I insmoded the em28xx,the device was detected as the
EM2860_BOARD_TYPHOON_DVD_MAKER??
I figured out the "TYPHOON_DVD_MAKER" and my Geniatech UTV3 must have
the same Vendor/Product ID.
#lsusb
Bus 004 Device 012: ID eb1a:2860 eMPIA Technology, Inc.
I guess somebody has to change the detection system to handle different
devices with the same Vendor/Product ID.
I had to make some modifications to the em28xx driver in order to get
the Geniatech device working.
I changed the EM2860_BOARD_TYPHOON_DVD_MAKER struct in em28xx-cards.c to
the following:
[EM2860_BOARD_TYPHOON_DVD_MAKER] = {
.name = "Geniatech UTV3",
.vchannels = 2,
.tuner_type = TUNER_TNF_5335MF,
.has_tuner = 1,
.norm = V4L2_STD_PAL_BG,
.decoder = EM28XX_SAA7113,
.dev_modes = EM28XX_VIDEO,
.input = {{
.type = EM28XX_VMUX_TELEVISION,
.vmux = SAA7115_COMPOSITE2,
.amux = 0,
},{
.type = EM28XX_VMUX_COMPOSITE1,
.vmux = SAA7115_COMPOSITE0,
.amux = 1,
}},
.tvnorms = {{
.name = "PAL-BG",
.id = V4L2_STD_PAL_BG,
},{
.name = "PAL-DK",
.id = V4L2_STD_PAL_DK,
},{
.name = "PAL-I",
.id = V4L2_STD_PAL_I,
},{
.name = "PAL-M",
.id = V4L2_STD_PAL_M,
},{
.name = "NTSC",
.id = V4L2_STD_NTSC,
}},
},
I know this isn't a 'proper' solution, but it's fine for me.
The tuner isn't actually a TVF58t5-MFF, it is an SN761678.
(the SN761678 is located inside the TNF8337-DFD)
After compiling and reloading the em28xx driver, the geniatech device
was properly detected.
#dmesg
[32985.830259] em28xx v4l2 driver version 0.0.1 loaded
[32985.830728] em28xx new video device (eb1a:2860): interface 0, class 255
[32985.830741] em28xx: device is attached to a USB 2.0 bus
[32985.830744] em28xx: you're using the experimental/unstable tree from
mcentral.de
[32985.830746] em28xx: there's also a stable tree available but which is
limited to
[32985.830749] em28xx: linux <=2.6.19.2
[32985.830750] em28xx: it's fine to use this driver but keep in mind
that it will move
[32985.830752] em28xx: to http://mcentral.de/hg/~mrec/v4l-dvb-kernel as
soon as it's
[32985.830754] em28xx: proved to be stable
[32985.832682] em28xx #0: Alternate settings: 8
[32985.832694] em28xx #0: Alternate setting 0, max size= 0
[32985.832696] em28xx #0: Alternate setting 1, max size= 0
[32985.832698] em28xx #0: Alternate setting 2, max size= 1448
[32985.832701] em28xx #0: Alternate setting 3, max size= 2048
[32985.832703] em28xx #0: Alternate setting 4, max size= 2304
[32985.832705] em28xx #0: Alternate setting 5, max size= 2580
[32985.832708] em28xx #0: Alternate setting 6, max size= 2892
[32985.832710] em28xx #0: Alternate setting 7, max size= 3072
[32985.936456] tuner 2-0061: I2C RECV = 7c 7c 7c 7c 7c 7c 7c 7c 7c 7c 7c
7c 7c 7c 7c 7c
[32985.936473] Tunder detected
[32985.936476] tuner 2-0061: chip found @ 0xc2 (em28xx #0)
[32985.936537] attach inform (default): detected I2C address c2
[32985.936543] tuner 0x61: Configuration acknowledged
[32985.936550] tuner 2-0061: type set to 69 (Tena TNF 5335 and similar
models)
[32985.963697] saa7115 2-0025: saa7113 found (1f7113d0e100000) @ 0x4a
(em28xx #0)
[32985.993604] attach_inform: saa7113 detected.
[32985.996353] attach_inform: eeprom detected.
[32986.023303] em28xx #0: i2c eeprom 00: 1a eb 67 95 1a eb 60 28 c0 00
3e 01 6a 22 00 00
[32986.023320] em28xx #0: i2c eeprom 10: 00 00 04 57 4e 03 00 00 60 c0
60 c0 02 02 02 02
[32986.023331] em28xx #0: i2c eeprom 20: 16 00 00 02 f0 10 02 00 4a 00
00 00 5b 00 00 00
[32986.023341] em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 10 01
02 01 00 00 00 00
[32986.023352] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[32986.023362] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[32986.023373] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00
22 03 55 00 53 00
[32986.023383] em28xx #0: i2c eeprom 70: 42 00 20 00 32 00 38 00 36 00
30 00 20 00 44 00
[32986.023394] em28xx #0: i2c eeprom 80: 65 00 76 00 69 00 63 00 65 00
00 00 00 00 00 00
[32986.023404] em28xx #0: i2c eeprom 90: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[32986.023415] em28xx #0: i2c eeprom a0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[32986.023425] em28xx #0: i2c eeprom b0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[32986.023436] em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[32986.023446] em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[32986.023456] em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[32986.023467] em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[32986.023477] EEPROM ID= 0x9567eb1a
[32986.023479] Vendor/Product ID= eb1a:2860
[32986.023481] No audio on board.
[32986.023482] 500mA max power
[32986.023485] Table at 0x04, strings=0x226a, 0x0000, 0x0000
[32986.040701] em28xx #0: V4L2 device registered as /dev/video0
[32986.040713] em28xx #0: Found Geniatech UTV3
[32986.040748] usbcore: registered new interface driver em28xx
With this new configuration I'm able to watch TV using xawtv.
Only the sound wasn't working.
The sound isn't available through the usb connection(like the driver
said), but it goes out by a audio jack connector.
After a while a discovered that the em28xx didn't controlled the
multiplexer (HCF4052).
The multiplexer is used to switch between the sound of the TV and the
sound of the AV.
In oder to get sound out of the audio connector the following
configuration has to applied to the multiplexer
A B
TV: 1 0
AV: 0 0
Other combinations give no output.
The multiplexer is connected by pin 10(A) and 9(B) to the em2860 by pin
27(PIO0) and 28(PIO1).
During the use of the em28xx driver the PIO0 and PIO1 are 3.3V, thus
resulting no sound.
The PIO's of the em2860 are probably configured as input, and are pulled
up to 3.3V
As a temporarily solution I lifted pin 9(B) from the multiplexer and
connected it to GND.
This way I can listen and watch to the TV.
I hope that this contribution can help to the further development of the
em28xx driver.
Greets,
Eli
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Geniatech UTV3
2008-09-16 17:09 Geniatech UTV3 eli hamels
@ 2008-09-16 17:33 ` Markus Rechberger
2008-09-17 15:11 ` eli hamels
2008-09-16 17:40 ` Devin Heitmueller
1 sibling, 1 reply; 4+ messages in thread
From: Markus Rechberger @ 2008-09-16 17:33 UTC (permalink / raw)
To: eli hamels; +Cc: video4linux-list, em28xx
On Tue, Sep 16, 2008 at 7:09 PM, eli hamels <eli.hamels@gmail.com> wrote:
> Hi all,
>
> I have a Geniatech UTV3 usb tv box that didn't worked on linux.
>
> After taking the device apart, I found following components
> * FM24C02 -> EEPROM
> * EM2860 -> USB Video Capture Device
> * SAA7113H -> Video input processor
> * TOA9801 -> Demodulator and FM-PLL detector (for sound)
> * HCF4052 -> Analog multiplexer (for switching sound between TV and AV)
> * TNF8337-DFD -> TV tuner/reciever
>
> After I insmoded the em28xx,the device was detected as the
> EM2860_BOARD_TYPHOON_DVD_MAKER??
> I figured out the "TYPHOON_DVD_MAKER" and my Geniatech UTV3 must have the
> same Vendor/Product ID.
>
> #lsusb
> Bus 004 Device 012: ID eb1a:2860 eMPIA Technology, Inc.
>
> I guess somebody has to change the detection system to handle different
> devices with the same Vendor/Product ID.
>
> I had to make some modifications to the em28xx driver in order to get the
> Geniatech device working.
> I changed the EM2860_BOARD_TYPHOON_DVD_MAKER struct in em28xx-cards.c to the
> following:
>
> [EM2860_BOARD_TYPHOON_DVD_MAKER] = {
> .name = "Geniatech UTV3",
> .vchannels = 2,
> .tuner_type = TUNER_TNF_5335MF,
> .has_tuner = 1,
> .norm = V4L2_STD_PAL_BG,
> .decoder = EM28XX_SAA7113,
> .dev_modes = EM28XX_VIDEO,
> .input = {{
> .type = EM28XX_VMUX_TELEVISION,
> .vmux = SAA7115_COMPOSITE2,
> .amux = 0,
> },{
> .type = EM28XX_VMUX_COMPOSITE1,
> .vmux = SAA7115_COMPOSITE0,
> .amux = 1,
> }},
> .tvnorms = {{
> .name = "PAL-BG",
> .id = V4L2_STD_PAL_BG,
> },{
> .name = "PAL-DK",
> .id = V4L2_STD_PAL_DK,
> },{
> .name = "PAL-I",
> .id = V4L2_STD_PAL_I,
> },{
> .name = "PAL-M",
> .id = V4L2_STD_PAL_M,
> },{
> .name = "NTSC",
> .id = V4L2_STD_NTSC,
> }},
> },
>
> I know this isn't a 'proper' solution, but it's fine for me.
>
> The tuner isn't actually a TVF58t5-MFF, it is an SN761678.
> (the SN761678 is located inside the TNF8337-DFD)
>
> After compiling and reloading the em28xx driver, the geniatech device was
> properly detected.
> #dmesg
> [32985.830259] em28xx v4l2 driver version 0.0.1 loaded
> [32985.830728] em28xx new video device (eb1a:2860): interface 0, class 255
> [32985.830741] em28xx: device is attached to a USB 2.0 bus
> [32985.830744] em28xx: you're using the experimental/unstable tree from
> mcentral.de
> [32985.830746] em28xx: there's also a stable tree available but which is
> limited to
> [32985.830749] em28xx: linux <=2.6.19.2
> [32985.830750] em28xx: it's fine to use this driver but keep in mind that it
> will move
> [32985.830752] em28xx: to http://mcentral.de/hg/~mrec/v4l-dvb-kernel as soon
> as it's
> [32985.830754] em28xx: proved to be stable
> [32985.832682] em28xx #0: Alternate settings: 8
> [32985.832694] em28xx #0: Alternate setting 0, max size= 0
> [32985.832696] em28xx #0: Alternate setting 1, max size= 0
> [32985.832698] em28xx #0: Alternate setting 2, max size= 1448
> [32985.832701] em28xx #0: Alternate setting 3, max size= 2048
> [32985.832703] em28xx #0: Alternate setting 4, max size= 2304
> [32985.832705] em28xx #0: Alternate setting 5, max size= 2580
> [32985.832708] em28xx #0: Alternate setting 6, max size= 2892
> [32985.832710] em28xx #0: Alternate setting 7, max size= 3072
> [32985.936456] tuner 2-0061: I2C RECV = 7c 7c 7c 7c 7c 7c 7c 7c 7c 7c 7c 7c
> 7c 7c 7c 7c
> [32985.936473] Tunder detected
> [32985.936476] tuner 2-0061: chip found @ 0xc2 (em28xx #0)
> [32985.936537] attach inform (default): detected I2C address c2
> [32985.936543] tuner 0x61: Configuration acknowledged
> [32985.936550] tuner 2-0061: type set to 69 (Tena TNF 5335 and similar
> models)
> [32985.963697] saa7115 2-0025: saa7113 found (1f7113d0e100000) @ 0x4a
> (em28xx #0)
> [32985.993604] attach_inform: saa7113 detected.
> [32985.996353] attach_inform: eeprom detected.
> [32986.023303] em28xx #0: i2c eeprom 00: 1a eb 67 95 1a eb 60 28 c0 00 3e 01
> 6a 22 00 00
> [32986.023320] em28xx #0: i2c eeprom 10: 00 00 04 57 4e 03 00 00 60 c0 60 c0
> 02 02 02 02
> [32986.023331] em28xx #0: i2c eeprom 20: 16 00 00 02 f0 10 02 00 4a 00 00 00
> 5b 00 00 00
> [32986.023341] em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 10 01 02 01
> 00 00 00 00
> [32986.023352] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00
> [32986.023362] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00
> [32986.023373] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 22 03
> 55 00 53 00
> [32986.023383] em28xx #0: i2c eeprom 70: 42 00 20 00 32 00 38 00 36 00 30 00
> 20 00 44 00
> [32986.023394] em28xx #0: i2c eeprom 80: 65 00 76 00 69 00 63 00 65 00 00 00
> 00 00 00 00
> [32986.023404] em28xx #0: i2c eeprom 90: 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00
> [32986.023415] em28xx #0: i2c eeprom a0: 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00
> [32986.023425] em28xx #0: i2c eeprom b0: 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00
> [32986.023436] em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00
> [32986.023446] em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00
> [32986.023456] em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00
> [32986.023467] em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00
> [32986.023477] EEPROM ID= 0x9567eb1a
> [32986.023479] Vendor/Product ID= eb1a:2860
> [32986.023481] No audio on board.
> [32986.023482] 500mA max power
> [32986.023485] Table at 0x04, strings=0x226a, 0x0000, 0x0000
> [32986.040701] em28xx #0: V4L2 device registered as /dev/video0
> [32986.040713] em28xx #0: Found Geniatech UTV3
> [32986.040748] usbcore: registered new interface driver em28xx
>
> With this new configuration I'm able to watch TV using xawtv.
> Only the sound wasn't working.
>
> The sound isn't available through the usb connection(like the driver said),
> but it goes out by a audio jack connector.
>
> After a while a discovered that the em28xx didn't controlled the multiplexer
> (HCF4052).
> The multiplexer is used to switch between the sound of the TV and the sound
> of the AV.
> In oder to get sound out of the audio connector the following configuration
> has to applied to the multiplexer
> A B
> TV: 1 0
> AV: 0 0
> Other combinations give no output.
>
> The multiplexer is connected by pin 10(A) and 9(B) to the em2860 by pin
> 27(PIO0) and 28(PIO1).
> During the use of the em28xx driver the PIO0 and PIO1 are 3.3V, thus
> resulting no sound.
> The PIO's of the em2860 are probably configured as input, and are pulled up
> to 3.3V
>
> As a temporarily solution I lifted pin 9(B) from the multiplexer and
> connected it to GND.
> This way I can listen and watch to the TV.
>
> I hope that this contribution can help to the further development of the
> em28xx driver.
>
can you submit the usbview output? depends what this device is set to
in order to get
audio through the digital link.
Markus
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Geniatech UTV3
2008-09-16 17:09 Geniatech UTV3 eli hamels
2008-09-16 17:33 ` Markus Rechberger
@ 2008-09-16 17:40 ` Devin Heitmueller
1 sibling, 0 replies; 4+ messages in thread
From: Devin Heitmueller @ 2008-09-16 17:40 UTC (permalink / raw)
To: eli hamels; +Cc: video4linux-list
On Tue, Sep 16, 2008 at 1:09 PM, eli hamels <eli.hamels@gmail.com> wrote:
> I guess somebody has to change the detection system to handle different
> devices with the same Vendor/Product ID.
FYI: the em28xx driver does have the ability to handle different
devices with the same Vendor/Product ID. See the em28xx_i2c_hash and
em28xx_eeprom_hash in em28xx_cards.c, used by the em28xx_hint_board()
function.
To use it, remove your entry from em28xx-cards.c, connect the device,
and the i2c hash will be shown in the dmesg output. Then just add it
to the list.
Regards,
Devin
--
Devin J. Heitmueller
http://www.devinheitmueller.com
AIM: devinheitmueller
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Geniatech UTV3
2008-09-16 17:33 ` Markus Rechberger
@ 2008-09-17 15:11 ` eli hamels
0 siblings, 0 replies; 4+ messages in thread
From: eli hamels @ 2008-09-17 15:11 UTC (permalink / raw)
To: Markus Rechberger; +Cc: video4linux-list, em28xx
Markus Rechberger wrote:
> On Tue, Sep 16, 2008 at 7:09 PM, eli hamels <eli.hamels@gmail.com> wrote:
>
>> Hi all,
>>
>> I have a Geniatech UTV3 usb tv box that didn't worked on linux.
>>
>> After taking the device apart, I found following components
>> * FM24C02 -> EEPROM
>> * EM2860 -> USB Video Capture Device
>> * SAA7113H -> Video input processor
>> * TOA9801 -> Demodulator and FM-PLL detector (for sound)
>> * HCF4052 -> Analog multiplexer (for switching sound between TV and AV)
>> * TNF8337-DFD -> TV tuner/reciever
>>
>> After I insmoded the em28xx,the device was detected as the
>> EM2860_BOARD_TYPHOON_DVD_MAKER??
>> I figured out the "TYPHOON_DVD_MAKER" and my Geniatech UTV3 must have the
>> same Vendor/Product ID.
>>
>> #lsusb
>> Bus 004 Device 012: ID eb1a:2860 eMPIA Technology, Inc.
>>
>> I guess somebody has to change the detection system to handle different
>> devices with the same Vendor/Product ID.
>>
>> I had to make some modifications to the em28xx driver in order to get the
>> Geniatech device working.
>> I changed the EM2860_BOARD_TYPHOON_DVD_MAKER struct in em28xx-cards.c to the
>> following:
>>
>> [EM2860_BOARD_TYPHOON_DVD_MAKER] = {
>> .name = "Geniatech UTV3",
>> .vchannels = 2,
>> .tuner_type = TUNER_TNF_5335MF,
>> .has_tuner = 1,
>> .norm = V4L2_STD_PAL_BG,
>> .decoder = EM28XX_SAA7113,
>> .dev_modes = EM28XX_VIDEO,
>> .input = {{
>> .type = EM28XX_VMUX_TELEVISION,
>> .vmux = SAA7115_COMPOSITE2,
>> .amux = 0,
>> },{
>> .type = EM28XX_VMUX_COMPOSITE1,
>> .vmux = SAA7115_COMPOSITE0,
>> .amux = 1,
>> }},
>> .tvnorms = {{
>> .name = "PAL-BG",
>> .id = V4L2_STD_PAL_BG,
>> },{
>> .name = "PAL-DK",
>> .id = V4L2_STD_PAL_DK,
>> },{
>> .name = "PAL-I",
>> .id = V4L2_STD_PAL_I,
>> },{
>> .name = "PAL-M",
>> .id = V4L2_STD_PAL_M,
>> },{
>> .name = "NTSC",
>> .id = V4L2_STD_NTSC,
>> }},
>> },
>>
>> I know this isn't a 'proper' solution, but it's fine for me.
>>
>> The tuner isn't actually a TVF58t5-MFF, it is an SN761678.
>> (the SN761678 is located inside the TNF8337-DFD)
>>
>> After compiling and reloading the em28xx driver, the geniatech device was
>> properly detected.
>> #dmesg
>> [32985.830259] em28xx v4l2 driver version 0.0.1 loaded
>> [32985.830728] em28xx new video device (eb1a:2860): interface 0, class 255
>> [32985.830741] em28xx: device is attached to a USB 2.0 bus
>> [32985.830744] em28xx: you're using the experimental/unstable tree from
>> mcentral.de
>> [32985.830746] em28xx: there's also a stable tree available but which is
>> limited to
>> [32985.830749] em28xx: linux <=2.6.19.2
>> [32985.830750] em28xx: it's fine to use this driver but keep in mind that it
>> will move
>> [32985.830752] em28xx: to http://mcentral.de/hg/~mrec/v4l-dvb-kernel as soon
>> as it's
>> [32985.830754] em28xx: proved to be stable
>> [32985.832682] em28xx #0: Alternate settings: 8
>> [32985.832694] em28xx #0: Alternate setting 0, max size= 0
>> [32985.832696] em28xx #0: Alternate setting 1, max size= 0
>> [32985.832698] em28xx #0: Alternate setting 2, max size= 1448
>> [32985.832701] em28xx #0: Alternate setting 3, max size= 2048
>> [32985.832703] em28xx #0: Alternate setting 4, max size= 2304
>> [32985.832705] em28xx #0: Alternate setting 5, max size= 2580
>> [32985.832708] em28xx #0: Alternate setting 6, max size= 2892
>> [32985.832710] em28xx #0: Alternate setting 7, max size= 3072
>> [32985.936456] tuner 2-0061: I2C RECV = 7c 7c 7c 7c 7c 7c 7c 7c 7c 7c 7c 7c
>> 7c 7c 7c 7c
>> [32985.936473] Tunder detected
>> [32985.936476] tuner 2-0061: chip found @ 0xc2 (em28xx #0)
>> [32985.936537] attach inform (default): detected I2C address c2
>> [32985.936543] tuner 0x61: Configuration acknowledged
>> [32985.936550] tuner 2-0061: type set to 69 (Tena TNF 5335 and similar
>> models)
>> [32985.963697] saa7115 2-0025: saa7113 found (1f7113d0e100000) @ 0x4a
>> (em28xx #0)
>> [32985.993604] attach_inform: saa7113 detected.
>> [32985.996353] attach_inform: eeprom detected.
>> [32986.023303] em28xx #0: i2c eeprom 00: 1a eb 67 95 1a eb 60 28 c0 00 3e 01
>> 6a 22 00 00
>> [32986.023320] em28xx #0: i2c eeprom 10: 00 00 04 57 4e 03 00 00 60 c0 60 c0
>> 02 02 02 02
>> [32986.023331] em28xx #0: i2c eeprom 20: 16 00 00 02 f0 10 02 00 4a 00 00 00
>> 5b 00 00 00
>> [32986.023341] em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 10 01 02 01
>> 00 00 00 00
>> [32986.023352] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00
>> 00 00 00 00
>> [32986.023362] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00
>> 00 00 00 00
>> [32986.023373] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 22 03
>> 55 00 53 00
>> [32986.023383] em28xx #0: i2c eeprom 70: 42 00 20 00 32 00 38 00 36 00 30 00
>> 20 00 44 00
>> [32986.023394] em28xx #0: i2c eeprom 80: 65 00 76 00 69 00 63 00 65 00 00 00
>> 00 00 00 00
>> [32986.023404] em28xx #0: i2c eeprom 90: 00 00 00 00 00 00 00 00 00 00 00 00
>> 00 00 00 00
>> [32986.023415] em28xx #0: i2c eeprom a0: 00 00 00 00 00 00 00 00 00 00 00 00
>> 00 00 00 00
>> [32986.023425] em28xx #0: i2c eeprom b0: 00 00 00 00 00 00 00 00 00 00 00 00
>> 00 00 00 00
>> [32986.023436] em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00
>> 00 00 00 00
>> [32986.023446] em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00
>> 00 00 00 00
>> [32986.023456] em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00
>> 00 00 00 00
>> [32986.023467] em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00
>> 00 00 00 00
>> [32986.023477] EEPROM ID= 0x9567eb1a
>> [32986.023479] Vendor/Product ID= eb1a:2860
>> [32986.023481] No audio on board.
>> [32986.023482] 500mA max power
>> [32986.023485] Table at 0x04, strings=0x226a, 0x0000, 0x0000
>> [32986.040701] em28xx #0: V4L2 device registered as /dev/video0
>> [32986.040713] em28xx #0: Found Geniatech UTV3
>> [32986.040748] usbcore: registered new interface driver em28xx
>>
>> With this new configuration I'm able to watch TV using xawtv.
>> Only the sound wasn't working.
>>
>> The sound isn't available through the usb connection(like the driver said),
>> but it goes out by a audio jack connector.
>>
>> After a while a discovered that the em28xx didn't controlled the multiplexer
>> (HCF4052).
>> The multiplexer is used to switch between the sound of the TV and the sound
>> of the AV.
>> In oder to get sound out of the audio connector the following configuration
>> has to applied to the multiplexer
>> A B
>> TV: 1 0
>> AV: 0 0
>> Other combinations give no output.
>>
>> The multiplexer is connected by pin 10(A) and 9(B) to the em2860 by pin
>> 27(PIO0) and 28(PIO1).
>> During the use of the em28xx driver the PIO0 and PIO1 are 3.3V, thus
>> resulting no sound.
>> The PIO's of the em2860 are probably configured as input, and are pulled up
>> to 3.3V
>>
>> As a temporarily solution I lifted pin 9(B) from the multiplexer and
>> connected it to GND.
>> This way I can listen and watch to the TV.
>>
>> I hope that this contribution can help to the further development of the
>> em28xx driver.
>>
>>
>
> can you submit the usbview output? depends what this device is set to
> in order to get
> audio through the digital link.
>
> Markus
>
Markus,
The sound goes only by the external audio jack, even in "windows".
In order to play audio through your PC speakers, the device comes with
an extra cable.
Witch you should connect to the line-in of the PC's audio card.
Anyway, here is the usbview output.
USB 2860 Device
Speed: 480Mb/s (high)
USB Version: 2.00
Device Class: 00(>ifc )
Device Subclass: 00
Device Protocol: 00
Maximum Default Endpoint Size: 64
Number of Configurations: 1
Vendor Id: eb1a
Product Id: 2860
Revision Number: 1.00
Config Number: 1
Number of Interfaces: 1
Attributes: 80
MaxPower Needed: 500mA
Interface Number: 0
Name: em28xx
Alternate Number: 0
Class: ff(vend.)
Sub Class: 00
Protocol: ff
Number of Endpoints: 3
Endpoint Address: 81
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 1
Interval: 128ms
Endpoint Address: 82
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 0
Interval: 125us
Endpoint Address: 84
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 0
Interval: 125us
Interface Number: 0
Name: em28xx
Alternate Number: 1
Class: ff(vend.)
Sub Class: 00
Protocol: ff
Number of Endpoints: 3
Endpoint Address: 81
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 1
Interval: 128ms
Endpoint Address: 82
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 0
Interval: 125us
Endpoint Address: 84
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 0
Interval: 125us
Interface Number: 0
Name: em28xx
Alternate Number: 2
Class: ff(vend.)
Sub Class: 00
Protocol: ff
Number of Endpoints: 3
Endpoint Address: 81
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 1
Interval: 128ms
Endpoint Address: 82
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 1448
Interval: 125us
Endpoint Address: 84
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 0
Interval: 125us
Interface Number: 0
Name: em28xx
Alternate Number: 3
Class: ff(vend.)
Sub Class: 00
Protocol: ff
Number of Endpoints: 3
Endpoint Address: 81
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 1
Interval: 128ms
Endpoint Address: 82
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 2048
Interval: 125us
Endpoint Address: 84
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 0
Interval: 125us
Interface Number: 0
Name: em28xx
Alternate Number: 4
Class: ff(vend.)
Sub Class: 00
Protocol: ff
Number of Endpoints: 3
Endpoint Address: 81
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 1
Interval: 128ms
Endpoint Address: 82
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 2304
Interval: 125us
Endpoint Address: 84
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 0
Interval: 125us
Interface Number: 0
Name: em28xx
Alternate Number: 5
Class: ff(vend.)
Sub Class: 00
Protocol: ff
Number of Endpoints: 3
Endpoint Address: 81
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 1
Interval: 128ms
Endpoint Address: 82
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 2580
Interval: 125us
Endpoint Address: 84
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 0
Interval: 125us
Interface Number: 0
Name: em28xx
Alternate Number: 6
Class: ff(vend.)
Sub Class: 00
Protocol: ff
Number of Endpoints: 3
Endpoint Address: 81
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 1
Interval: 128ms
Endpoint Address: 82
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 2892
Interval: 125us
Endpoint Address: 84
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 0
Interval: 125us
Interface Number: 0
Name: em28xx
Alternate Number: 7
Class: ff(vend.)
Sub Class: 00
Protocol: ff
Number of Endpoints: 3
Endpoint Address: 81
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 1
Interval: 128ms
Endpoint Address: 82
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 3072
Interval: 125us
Endpoint Address: 84
Direction: in
Attribute: 1
Type: Isoc
Max Packet Size: 0
Interval: 125us
Greets,
Eli
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2008-09-17 15:11 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-09-16 17:09 Geniatech UTV3 eli hamels
2008-09-16 17:33 ` Markus Rechberger
2008-09-17 15:11 ` eli hamels
2008-09-16 17:40 ` Devin Heitmueller
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox