* [linux-dvb] DVICO FusionHDTV5 Express Support
@ 2008-09-22 3:44 James Evans
2008-09-22 4:00 ` Steven Toth
0 siblings, 1 reply; 8+ messages in thread
From: James Evans @ 2008-09-22 3:44 UTC (permalink / raw)
To: linux-dvb
I emailed quite a while ago and have been following the mail list ever since, but I was curious as to what might be the major hurdle
to getting support for the DVICO FusionHDTV5 Express card (http://www.fusionhdtv.co.kr/eng/Products/fusion5express.aspx) . It
utilizes the CX23885 Chipset and the 5th Gen. LG Tuner, which both seem to be supported, as well as some PCIx interfaced cards.
Following is my current system stats as well as the relevant portion of the 'messages' file:
Gentoo linux kernel 2.6.26-gentoo-r1 x86_64 Dual Core Athlon 4400+
DVICO FusionHDTV5 Express
Air2PC/AirStar 2 ATSC 3rd generation (HD5000) (x2)
#====================== SNIP =======================================================
Sep 17 02:32:09 localhost Linux video capture interface: v2.00
Sep 17 02:32:09 localhost bttv: driver version 0.9.17 loaded
Sep 17 02:32:09 localhost bttv: using 8 buffers with 2080k (520 pages) each for capture
Sep 17 02:32:09 localhost saa7130/34: v4l2 driver version 0.2.14 loaded
Sep 17 02:32:09 localhost cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
Sep 17 02:32:09 localhost cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
Sep 17 02:32:09 localhost cx2388x alsa driver version 0.0.6 loaded
Sep 17 02:32:09 localhost cx2388x blackbird driver version 0.0.6 loaded
Sep 17 02:32:09 localhost cx88/2: registering cx8802 driver, type: blackbird access: shared
Sep 17 02:32:09 localhost cx88/2: cx2388x dvb driver version 0.0.6 loaded
Sep 17 02:32:09 localhost cx88/2: registering cx8802 driver, type: dvb access: shared
Sep 17 02:32:09 localhost ivtv: Start initialization, version 1.3.0
Sep 17 02:32:09 localhost ivtv: End initialization
Sep 17 02:32:09 localhost ivtvfb: no cards found<6>cx23885 driver version 0.0.1 loaded
Sep 17 02:32:09 localhost ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 19
Sep 17 02:32:09 localhost ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNEA] -> GSI 19 (level, low) -> IRQ 19
Sep 17 02:32:09 localhost CORE cx23885[0]: subsystem: 18ac:d500, board: DViCO FusionHDTV5 Express [card=4,autodetected]
Sep 17 02:32:09 localhost input: i2c IR (FusionHDTV) as /class/input/input2
Sep 17 02:32:09 localhost ir-kbd-i2c: i2c IR (FusionHDTV) detected at i2c-0/0-006b/ir0 [cx23885[0]]
Sep 17 02:32:09 localhost tvaudio' 0-0041: tda8425 found @ 0x82 (cx23885[0])
Sep 17 02:32:09 localhost tuner' 0-0043: chip found @ 0x86 (cx23885[0])
Sep 17 02:32:09 localhost tda9887 0-0043: creating new instance
Sep 17 02:32:09 localhost tda9887 0-0043: tda988[5/6/7] found
Sep 17 02:32:09 localhost tuner' 0-0061: chip found @ 0xc2 (cx23885[0])
Sep 17 02:32:09 localhost cx23885[0]: i2c bus 0 registered
Sep 17 02:32:09 localhost cx23885[0]: i2c bus 1 registered
Sep 17 02:32:09 localhost tvaudio' 2-004c: tea6420 found @ 0x98 (cx23885[0])
Sep 17 02:32:09 localhost msp3400' 2-0044: MSP164209A-17 found @ 0x88 (cx23885[0])
Sep 17 02:32:09 localhost msp3400' 2-0044: msp3400 mode is manual
Sep 17 02:32:09 localhost cx23885[0]: i2c bus 2 registered
Sep 17 02:32:09 localhost cx23885[0]: cx23885 based dvb card
Sep 17 02:32:09 localhost tuner-simple 0-0061: creating new instance
Sep 17 02:32:09 localhost tuner-simple 0-0061: type set to 64 (LG TDVS-H06xF)
Sep 17 02:32:09 localhost DVB: registering new adapter (cx23885[0])
Sep 17 02:32:09 localhost DVB: registering frontend 0 (LG Electronics LGDT3303 VSB/QAM Frontend)...
Sep 17 02:32:09 localhost cx23885_dev_checkrevision() Hardware revision = 0xb0
Sep 17 02:32:09 localhost cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 19, latency: 0, mmio: 0xfa800000
Sep 17 02:32:09 localhost PCI: Setting latency timer of device 0000:02:00.0 to 64
Sep 17 02:32:09 localhost b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
Sep 17 02:32:09 localhost flexcop-pci: will use the HW PID filter.
Sep 17 02:32:09 localhost flexcop-pci: card revision 2
Sep 17 02:32:09 localhost ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 18
Sep 17 02:32:09 localhost ACPI: PCI Interrupt 0000:04:08.0[A] -> Link [LNKA] -> GSI 18 (level, low) -> IRQ 18
Sep 17 02:32:09 localhost DVB: registering new adapter (FlexCop Digital TV device)
Sep 17 02:32:09 localhost i2c-adapter i2c-3: SMBus Quick command not supported, can't probe for chips
Sep 17 02:32:09 localhost i2c-adapter i2c-4: SMBus Quick command not supported, can't probe for chips
Sep 17 02:32:09 localhost i2c-adapter i2c-5: SMBus Quick command not supported, can't probe for chips
Sep 17 02:32:09 localhost b2c2-flexcop: MAC address = 00:d0:d7:0e:a6:c8
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost CX24123: cx24123_i2c_readreg: reg=0x0 (error=-121)
Sep 17 02:32:09 localhost CX24123: wrong demod revision: 87
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost mt352_read_register: readreg error (reg=127, ret==-121)
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
Sep 17 02:32:09 localhost Unknown/Unsupported NXT chip: 00 00 00 00 00
Sep 17 02:32:09 localhost tuner-simple 3-0061: creating new instance
Sep 17 02:32:09 localhost tuner-simple 3-0061: type set to 64 (LG TDVS-H06xF)
Sep 17 02:32:09 localhost b2c2-flexcop: found 'LG Electronics LGDT3303 VSB/QAM Frontend' .
Sep 17 02:32:09 localhost DVB: registering frontend 1 (LG Electronics LGDT3303 VSB/QAM Frontend)...
Sep 17 02:32:09 localhost b2c2-flexcop: initialization of 'Air2PC/AirStar 2 ATSC 3rd generation (HD5000)' at the 'PCI' bus
controlled by a 'FlexCopIIb' complete
Sep 17 02:32:09 localhost flexcop-pci: will use the HW PID filter.
Sep 17 02:32:09 localhost flexcop-pci: card revision 2
Sep 17 02:32:09 localhost ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 17
Sep 17 02:32:09 localhost ACPI: PCI Interrupt 0000:04:09.0[A] -> Link [LNKB] -> GSI 17 (level, low) -> IRQ 17
Sep 17 02:32:09 localhost DVB: registering new adapter (FlexCop Digital TV device)
Sep 17 02:32:09 localhost i2c-adapter i2c-6: SMBus Quick command not supported, can't probe for chips
Sep 17 02:32:09 localhost i2c-adapter i2c-7: SMBus Quick command not supported, can't probe for chips
Sep 17 02:32:09 localhost i2c-adapter i2c-8: SMBus Quick command not supported, can't probe for chips
Sep 17 02:32:09 localhost b2c2-flexcop: MAC address = 00:d0:d7:0e:6c:aa
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost CX24123: cx24123_i2c_readreg: reg=0x0 (error=-121)
Sep 17 02:32:09 localhost CX24123: wrong demod revision: 87
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost mt352_read_register: readreg error (reg=127, ret==-121)
Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
Sep 17 02:32:09 localhost nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
Sep 17 02:32:09 localhost Unknown/Unsupported NXT chip: 00 00 00 00 00
Sep 17 02:32:09 localhost tuner-simple 6-0061: creating new instance
Sep 17 02:32:09 localhost tuner-simple 6-0061: type set to 64 (LG TDVS-H06xF)
Sep 17 02:32:09 localhost b2c2-flexcop: found 'LG Electronics LGDT3303 VSB/QAM Frontend' .
Sep 17 02:32:09 localhost DVB: registering frontend 2 (LG Electronics LGDT3303 VSB/QAM Frontend)...
Sep 17 02:32:09 localhost b2c2-flexcop: initialization of 'Air2PC/AirStar 2 ATSC 3rd generation (HD5000)' at the 'PCI' bus
controlled by a 'FlexCopIIb' complete
Sep 17 02:32:09 localhost bt878: AUDIO driver version 0.0.0 loaded
#====================== SNIP =======================================================
Given the above it looks like it is detected properly and I can even find the adapter under /dev/dvb. The problem I seem to be
having is when it comes to getting it to tune. I get the following errors:
#====================== BEGIN ======================================================
scanning /usr/share/dvb/atsc/us-ATSC-center-frequencies-8VSB
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
>>> tune to: 57028615:8VSB
WARNING: >>> tuning failed!!!
>>> tune to: 57028615:8VSB (tuning failed)
WARNING: >>> tuning failed!!!
>>> tune to: 63028615:8VSB
WARNING: >>> tuning failed!!!
>>> tune to: 63028615:8VSB (tuning failed)
WARNING: >>> tuning failed!!!
>>> tune to: 69028615:8VSB
WARNING: >>> tuning failed!!!
>>> tune to: 69028615:8VSB (tuning failed)
WARNING: >>> tuning failed!!!
>>> tune to: 79028615:8VSB
WARNING: >>> tuning failed!!!
>>> tune to: 79028615:8VSB (tuning failed)
WARNING: >>> tuning failed!!!
>>> tune to: 85028615:8VSB
WARNING: >>> tuning failed!!!
>>> tune to: 85028615:8VSB (tuning failed)
WARNING: >>> tuning failed!!!
>>> tune to: 177028615:8VSB
WARNING: >>> tuning failed!!!
>>> tune to: 177028615:8VSB (tuning failed)
WARNING: >>> tuning failed!!!
>>> tune to: 183028615:8VSB
WARNING: >>> tuning failed!!!
#====================== SNIP =======================================================
I figure the problem is really operator error, but I cannot seem to figure it out. I probably just can't see the forest because of
all those dang trees.
Any help, ideas, suggestions, anything would be greatly appreciated.
Thanks,
--J. Evans
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [linux-dvb] DVICO FusionHDTV5 Express Support
2008-09-22 3:44 [linux-dvb] DVICO FusionHDTV5 Express Support James Evans
@ 2008-09-22 4:00 ` Steven Toth
2008-09-22 4:26 ` James Evans
0 siblings, 1 reply; 8+ messages in thread
From: Steven Toth @ 2008-09-22 4:00 UTC (permalink / raw)
To: James Evans; +Cc: linux-dvb
James Evans wrote:
> I emailed quite a while ago and have been following the mail list ever since, but I was curious as to what might be the major hurdle
> to getting support for the DVICO FusionHDTV5 Express card (http://www.fusionhdtv.co.kr/eng/Products/fusion5express.aspx) . It
> utilizes the CX23885 Chipset and the 5th Gen. LG Tuner, which both seem to be supported, as well as some PCIx interfaced cards.
>
> Following is my current system stats as well as the relevant portion of the 'messages' file:
>
> Gentoo linux kernel 2.6.26-gentoo-r1 x86_64 Dual Core Athlon 4400+
> DVICO FusionHDTV5 Express
> Air2PC/AirStar 2 ATSC 3rd generation (HD5000) (x2)
>
> #====================== SNIP =======================================================
> Sep 17 02:32:09 localhost Linux video capture interface: v2.00
> Sep 17 02:32:09 localhost bttv: driver version 0.9.17 loaded
> Sep 17 02:32:09 localhost bttv: using 8 buffers with 2080k (520 pages) each for capture
> Sep 17 02:32:09 localhost saa7130/34: v4l2 driver version 0.2.14 loaded
> Sep 17 02:32:09 localhost cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
> Sep 17 02:32:09 localhost cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
> Sep 17 02:32:09 localhost cx2388x alsa driver version 0.0.6 loaded
> Sep 17 02:32:09 localhost cx2388x blackbird driver version 0.0.6 loaded
> Sep 17 02:32:09 localhost cx88/2: registering cx8802 driver, type: blackbird access: shared
> Sep 17 02:32:09 localhost cx88/2: cx2388x dvb driver version 0.0.6 loaded
> Sep 17 02:32:09 localhost cx88/2: registering cx8802 driver, type: dvb access: shared
> Sep 17 02:32:09 localhost ivtv: Start initialization, version 1.3.0
> Sep 17 02:32:09 localhost ivtv: End initialization
> Sep 17 02:32:09 localhost ivtvfb: no cards found<6>cx23885 driver version 0.0.1 loaded
> Sep 17 02:32:09 localhost ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 19
> Sep 17 02:32:09 localhost ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNEA] -> GSI 19 (level, low) -> IRQ 19
> Sep 17 02:32:09 localhost CORE cx23885[0]: subsystem: 18ac:d500, board: DViCO FusionHDTV5 Express [card=4,autodetected]
> Sep 17 02:32:09 localhost input: i2c IR (FusionHDTV) as /class/input/input2
> Sep 17 02:32:09 localhost ir-kbd-i2c: i2c IR (FusionHDTV) detected at i2c-0/0-006b/ir0 [cx23885[0]]
> Sep 17 02:32:09 localhost tvaudio' 0-0041: tda8425 found @ 0x82 (cx23885[0])
> Sep 17 02:32:09 localhost tuner' 0-0043: chip found @ 0x86 (cx23885[0])
> Sep 17 02:32:09 localhost tda9887 0-0043: creating new instance
> Sep 17 02:32:09 localhost tda9887 0-0043: tda988[5/6/7] found
> Sep 17 02:32:09 localhost tuner' 0-0061: chip found @ 0xc2 (cx23885[0])
> Sep 17 02:32:09 localhost cx23885[0]: i2c bus 0 registered
> Sep 17 02:32:09 localhost cx23885[0]: i2c bus 1 registered
> Sep 17 02:32:09 localhost tvaudio' 2-004c: tea6420 found @ 0x98 (cx23885[0])
> Sep 17 02:32:09 localhost msp3400' 2-0044: MSP164209A-17 found @ 0x88 (cx23885[0])
> Sep 17 02:32:09 localhost msp3400' 2-0044: msp3400 mode is manual
> Sep 17 02:32:09 localhost cx23885[0]: i2c bus 2 registered
> Sep 17 02:32:09 localhost cx23885[0]: cx23885 based dvb card
> Sep 17 02:32:09 localhost tuner-simple 0-0061: creating new instance
> Sep 17 02:32:09 localhost tuner-simple 0-0061: type set to 64 (LG TDVS-H06xF)
> Sep 17 02:32:09 localhost DVB: registering new adapter (cx23885[0])
> Sep 17 02:32:09 localhost DVB: registering frontend 0 (LG Electronics LGDT3303 VSB/QAM Frontend)...
> Sep 17 02:32:09 localhost cx23885_dev_checkrevision() Hardware revision = 0xb0
> Sep 17 02:32:09 localhost cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 19, latency: 0, mmio: 0xfa800000
> Sep 17 02:32:09 localhost PCI: Setting latency timer of device 0000:02:00.0 to 64
> Sep 17 02:32:09 localhost b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
> Sep 17 02:32:09 localhost flexcop-pci: will use the HW PID filter.
> Sep 17 02:32:09 localhost flexcop-pci: card revision 2
> Sep 17 02:32:09 localhost ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 18
> Sep 17 02:32:09 localhost ACPI: PCI Interrupt 0000:04:08.0[A] -> Link [LNKA] -> GSI 18 (level, low) -> IRQ 18
> Sep 17 02:32:09 localhost DVB: registering new adapter (FlexCop Digital TV device)
> Sep 17 02:32:09 localhost i2c-adapter i2c-3: SMBus Quick command not supported, can't probe for chips
> Sep 17 02:32:09 localhost i2c-adapter i2c-4: SMBus Quick command not supported, can't probe for chips
> Sep 17 02:32:09 localhost i2c-adapter i2c-5: SMBus Quick command not supported, can't probe for chips
> Sep 17 02:32:09 localhost b2c2-flexcop: MAC address = 00:d0:d7:0e:a6:c8
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost CX24123: cx24123_i2c_readreg: reg=0x0 (error=-121)
> Sep 17 02:32:09 localhost CX24123: wrong demod revision: 87
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost mt352_read_register: readreg error (reg=127, ret==-121)
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
> Sep 17 02:32:09 localhost Unknown/Unsupported NXT chip: 00 00 00 00 00
> Sep 17 02:32:09 localhost tuner-simple 3-0061: creating new instance
> Sep 17 02:32:09 localhost tuner-simple 3-0061: type set to 64 (LG TDVS-H06xF)
> Sep 17 02:32:09 localhost b2c2-flexcop: found 'LG Electronics LGDT3303 VSB/QAM Frontend' .
> Sep 17 02:32:09 localhost DVB: registering frontend 1 (LG Electronics LGDT3303 VSB/QAM Frontend)...
> Sep 17 02:32:09 localhost b2c2-flexcop: initialization of 'Air2PC/AirStar 2 ATSC 3rd generation (HD5000)' at the 'PCI' bus
> controlled by a 'FlexCopIIb' complete
> Sep 17 02:32:09 localhost flexcop-pci: will use the HW PID filter.
> Sep 17 02:32:09 localhost flexcop-pci: card revision 2
> Sep 17 02:32:09 localhost ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 17
> Sep 17 02:32:09 localhost ACPI: PCI Interrupt 0000:04:09.0[A] -> Link [LNKB] -> GSI 17 (level, low) -> IRQ 17
> Sep 17 02:32:09 localhost DVB: registering new adapter (FlexCop Digital TV device)
> Sep 17 02:32:09 localhost i2c-adapter i2c-6: SMBus Quick command not supported, can't probe for chips
> Sep 17 02:32:09 localhost i2c-adapter i2c-7: SMBus Quick command not supported, can't probe for chips
> Sep 17 02:32:09 localhost i2c-adapter i2c-8: SMBus Quick command not supported, can't probe for chips
> Sep 17 02:32:09 localhost b2c2-flexcop: MAC address = 00:d0:d7:0e:6c:aa
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost CX24123: cx24123_i2c_readreg: reg=0x0 (error=-121)
> Sep 17 02:32:09 localhost CX24123: wrong demod revision: 87
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost mt352_read_register: readreg error (reg=127, ret==-121)
> Sep 17 02:32:09 localhost b2c2-flexcop: i2c master_xfer failed
> Sep 17 02:32:09 localhost nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
> Sep 17 02:32:09 localhost Unknown/Unsupported NXT chip: 00 00 00 00 00
> Sep 17 02:32:09 localhost tuner-simple 6-0061: creating new instance
> Sep 17 02:32:09 localhost tuner-simple 6-0061: type set to 64 (LG TDVS-H06xF)
> Sep 17 02:32:09 localhost b2c2-flexcop: found 'LG Electronics LGDT3303 VSB/QAM Frontend' .
> Sep 17 02:32:09 localhost DVB: registering frontend 2 (LG Electronics LGDT3303 VSB/QAM Frontend)...
> Sep 17 02:32:09 localhost b2c2-flexcop: initialization of 'Air2PC/AirStar 2 ATSC 3rd generation (HD5000)' at the 'PCI' bus
> controlled by a 'FlexCopIIb' complete
> Sep 17 02:32:09 localhost bt878: AUDIO driver version 0.0.0 loaded
> #====================== SNIP =======================================================
>
> Given the above it looks like it is detected properly and I can even find the adapter under /dev/dvb. The problem I seem to be
> having is when it comes to getting it to tune. I get the following errors:
>
> #====================== BEGIN ======================================================
> scanning /usr/share/dvb/atsc/us-ATSC-center-frequencies-8VSB
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
>>>> tune to: 57028615:8VSB
> WARNING: >>> tuning failed!!!
>>>> tune to: 57028615:8VSB (tuning failed)
> WARNING: >>> tuning failed!!!
>>>> tune to: 63028615:8VSB
> WARNING: >>> tuning failed!!!
>>>> tune to: 63028615:8VSB (tuning failed)
> WARNING: >>> tuning failed!!!
>>>> tune to: 69028615:8VSB
> WARNING: >>> tuning failed!!!
>>>> tune to: 69028615:8VSB (tuning failed)
> WARNING: >>> tuning failed!!!
>>>> tune to: 79028615:8VSB
> WARNING: >>> tuning failed!!!
>>>> tune to: 79028615:8VSB (tuning failed)
> WARNING: >>> tuning failed!!!
>>>> tune to: 85028615:8VSB
> WARNING: >>> tuning failed!!!
>>>> tune to: 85028615:8VSB (tuning failed)
> WARNING: >>> tuning failed!!!
>>>> tune to: 177028615:8VSB
> WARNING: >>> tuning failed!!!
>>>> tune to: 177028615:8VSB (tuning failed)
> WARNING: >>> tuning failed!!!
>>>> tune to: 183028615:8VSB
> WARNING: >>> tuning failed!!!
> #====================== SNIP =======================================================
>
> I figure the problem is really operator error, but I cannot seem to figure it out. I probably just can't see the forest because of
> all those dang trees.
>
> Any help, ideas, suggestions, anything would be greatly appreciated.
> Thanks,
> --J. Evans
Debug looks OK. If you have another board where you know for certain
that tuning a specific 8VSB frequency works, then tuning this same
frequency with the LG should probably work reliably.
In terms of the tuner-to-demod, are you confident that the I/F is set
correctly? (And inversion for that matter?)
- Steve
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [linux-dvb] DVICO FusionHDTV5 Express Support
2008-09-22 4:00 ` Steven Toth
@ 2008-09-22 4:26 ` James Evans
2008-09-22 5:02 ` Steven Toth
0 siblings, 1 reply; 8+ messages in thread
From: James Evans @ 2008-09-22 4:26 UTC (permalink / raw)
To: 'Steven Toth'; +Cc: linux-dvb
Thank you for such a quick response.
> Debug looks OK. If you have another board where you know for certain
> that tuning a specific 8VSB frequency works, then tuning this same
> frequency with the LG should probably work reliably.
The installed Airstar HD5000 cards both have an LG tuner and can tune perfectly fine.
> In terms of the tuner-to-demod, are you confident that the I/F is set
> correctly? (And inversion for that matter?)
I am not sure I understand the above question. How would I go about setting up the interface for the tuner-to-demod?
Thanks,
--J. Evans
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [linux-dvb] DVICO FusionHDTV5 Express Support
2008-09-22 4:26 ` James Evans
@ 2008-09-22 5:02 ` Steven Toth
2008-09-22 23:27 ` James Evans
0 siblings, 1 reply; 8+ messages in thread
From: Steven Toth @ 2008-09-22 5:02 UTC (permalink / raw)
To: James Evans; +Cc: linux-dvb
James Evans wrote:
> Thank you for such a quick response.
>
>> Debug looks OK. If you have another board where you know for certain
>> that tuning a specific 8VSB frequency works, then tuning this same
>> frequency with the LG should probably work reliably.
>
> The installed Airstar HD5000 cards both have an LG tuner and can tune perfectly fine.
OK, pick a single frequency and focus on always tuning that for the time
being with the Express card.
>
>> In terms of the tuner-to-demod, are you confident that the I/F is set
>> correctly? (And inversion for that matter?)
>
> I am not sure I understand the above question. How would I go about setting up the interface for the tuner-to-demod?
/me checks the code and thinks it should be working fine.
Specifically, please list here the frequencies that lock reliably for
you on 8VSB with other boards. I've seen issues in the past (mainly due
to driver issues) where channels tables work reliably for one tuner but
not for another.
Still, that shouldn't effect a new complete scan using the 5_EXP card,
the channels table would be wrong if that was the case, but it would
still lock.... unless something broke.
- Steve
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [linux-dvb] DVICO FusionHDTV5 Express Support
2008-09-22 5:02 ` Steven Toth
@ 2008-09-22 23:27 ` James Evans
2008-09-23 0:22 ` Steven Toth
0 siblings, 1 reply; 8+ messages in thread
From: James Evans @ 2008-09-22 23:27 UTC (permalink / raw)
To: 'Steven Toth'; +Cc: linux-dvb
> James Evans wrote:
> > Thank you for such a quick response.
> >
> >> Debug looks OK. If you have another board where you know for certain
> >> that tuning a specific 8VSB frequency works, then tuning this same
> >> frequency with the LG should probably work reliably.
> >
> > The installed Airstar HD5000 cards both have an LG tuner and can tune perfectly fine.
>
> OK, pick a single frequency and focus on always tuning that for the time
> being with the Express card.
HD5000 Results:
% /usr/bin/azap -a 1 -r -c ~/.azap/channels.conf "KTTV DT"
using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'
tuning to 779028615 Hz
video pid 0x0031, audio pid 0x0034
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 1e | signal c6ce | snr 1b2e | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1e | signal e4e6 | snr 1f4b | ber 00000000 | unc 0000003d | FE_HAS_LOCK
status 1e | signal e1b8 | snr 1edc | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1e | signal e86e | snr 1fc7 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1e | signal e86e | snr 1fc7 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1e | signal daef | snr 1dee | ber 00000000 | unc 00000000 | FE_HAS_LOCK
^C
FusionHDTV5 Results:
% /usr/bin/azap -a 0 -r -c ~/.azap/channels.conf "KTTV DT"
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
tuning to 779028615 Hz
video pid 0x0031, audio pid 0x0034
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
^C
>
> >
> >> In terms of the tuner-to-demod, are you confident that the I/F is set
> >> correctly? (And inversion for that matter?)
> >
> > I am not sure I understand the above question. How would I go about setting up the interface for
> the tuner-to-demod?
>
> /me checks the code and thinks it should be working fine.
>
> Specifically, please list here the frequencies that lock reliably for
> you on 8VSB with other boards. I've seen issues in the past (mainly due
> to driver issues) where channels tables work reliably for one tuner but
> not for another.
Here is the working table that the HD5000 boards are using.
KFLA-LD:183028615:8VSB:4128:4129:1
HCCN:183028615:8VSB:4130:4131:2
CVTV:183028615:8VSB:4640:4641:3
WSTV:183028615:8VSB:80:89:4
KTBN-DT 1:527028615:8VSB:49:52:3
KTBN-DT 2:527028615:8VSB:65:68:4
KTBN-DT 3:527028615:8VSB:81:84:5
KTBN-DT 4:527028615:8VSB:97:100:6
KTBN-DT 5:527028615:8VSB:113:116:7
TeleFutura:563028615:8VSB:49:52:3
KTLA-DT:575028615:8VSB:49:52:3
KDOC-HD:581028615:8VSB:49:52:1
KDOCSD1:581028615:8VSB:65:68:2
[0004]:581028615:8VSB:81:84:4
KDOCSD2:581028615:8VSB:81:84:3
Univision:599028615:8VSB:49:52:3
NBC-4LA:605028615:8VSB:49:52:3
WX-Plus:605028615:8VSB:65:68:4
NewsRaw:605028615:8VSB:81:84:5
ION:617028615:8VSB:49:52:3
KPXN qubo:617028615:8VSB:65:68:4
IONLife:617028615:8VSB:81:84:5
Worship:617028615:8VSB:97:100:6
KVEA-HD:623028615:8VSB:49:52:3
KVEA-SD:623028615:8VSB:65:68:4
KLCS-DT:635028615:8VSB:49:52:2
KLCS-DT:635028615:8VSB:65:68:3
KLCS-DT:635028615:8VSB:81:84:4
KLCS-DT:635028615:8VSB:97:100:5
[0006]:635028615:8VSB:113:116:6
KWHY-HD:641028615:8VSB:49:52:3
KWHY-SD:641028615:8VSB:65:68:4
KCAL-DT:647028615:8VSB:49:52:1
KAZA-DT:671028615:8VSB:49:52:3
KAZA-TV:671028615:8VSB:0:0:65535
KOCE-HD:677028615:8VSB:49:52:3
KOCE-OC:677028615:8VSB:65:68:4
KOCE-SD:677028615:8VSB:81:84:5
Daystar:677028615:8VSB:97:100:6
KOCE-TV:677028615:8VSB:0:0:65535
KJLA-DT:683028615:8VSB:49:52:3
KXLA-DT:683028615:8VSB:65:68:4
KVMD-DT:683028615:8VSB:81:84:5
LATV:683028615:8VSB:97:100:6
KXLA-DT:695028615:8VSB:49:52:3
KVMD-DT:695028615:8VSB:65:68:4
KABC-DT:707028615:8VSB:49:52:1
KABC-SD:707028615:8VSB:65:68:2
KABC-WN:707028615:8VSB:81:84:3
KCET-HD:743028615:8VSB:49:52:1
KCET-OC:743028615:8VSB:97:100:2
KCET-Vm:743028615:8VSB:81:84:3
KCET-W:743028615:8VSB:65:68:4
[0009]:743028615:8VSB:0:0:9
[000a]:743028615:8VSB:0:0:10
KCBS-DT:749028615:8VSB:49:52:1
LA18.1:755028615:8VSB:49:52:1
LA18.8:755028615:8VSB:161:164:8
LA18.5:755028615:8VSB:113:116:5
LA18.7:755028615:8VSB:145:148:7
LA18.3:755028615:8VSB:81:84:3
LA18.6:755028615:8VSB:129:132:6
LA18:755028615:8VSB:0:0:65535
KTTV DT:779028615:8VSB:49:52:3
KCOP DT:785028615:8VSB:49:52:3
KRCA-DT:797028615:8VSB:49:52:1
KRCA-DT:797028615:8VSB:65:68:2
Thanks again for the help!
--James Evans
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [linux-dvb] DVICO FusionHDTV5 Express Support
2008-09-22 23:27 ` James Evans
@ 2008-09-23 0:22 ` Steven Toth
2008-09-23 14:48 ` James Evans
0 siblings, 1 reply; 8+ messages in thread
From: Steven Toth @ 2008-09-23 0:22 UTC (permalink / raw)
To: James Evans; +Cc: linux-dvb
James Evans wrote:
>> James Evans wrote:
>>> Thank you for such a quick response.
>>>
>>>> Debug looks OK. If you have another board where you know for certain
>>>> that tuning a specific 8VSB frequency works, then tuning this same
>>>> frequency with the LG should probably work reliably.
>>> The installed Airstar HD5000 cards both have an LG tuner and can tune perfectly fine.
>> OK, pick a single frequency and focus on always tuning that for the time
>> being with the Express card.
>
> HD5000 Results:
> % /usr/bin/azap -a 1 -r -c ~/.azap/channels.conf "KTTV DT"
> using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'
> tuning to 779028615 Hz
> video pid 0x0031, audio pid 0x0034
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 1e | signal c6ce | snr 1b2e | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1e | signal e4e6 | snr 1f4b | ber 00000000 | unc 0000003d | FE_HAS_LOCK
> status 1e | signal e1b8 | snr 1edc | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1e | signal e86e | snr 1fc7 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1e | signal e86e | snr 1fc7 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> status 1e | signal daef | snr 1dee | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> ^C
>
> FusionHDTV5 Results:
> % /usr/bin/azap -a 0 -r -c ~/.azap/channels.conf "KTTV DT"
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> tuning to 779028615 Hz
> video pid 0x0031, audio pid 0x0034
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> ^C
>
>>>> In terms of the tuner-to-demod, are you confident that the I/F is set
>>>> correctly? (And inversion for that matter?)
>>> I am not sure I understand the above question. How would I go about setting up the interface for
>> the tuner-to-demod?
>>
>> /me checks the code and thinks it should be working fine.
>>
>> Specifically, please list here the frequencies that lock reliably for
>> you on 8VSB with other boards. I've seen issues in the past (mainly due
>> to driver issues) where channels tables work reliably for one tuner but
>> not for another.
>
> Here is the working table that the HD5000 boards are using.
>
> KFLA-LD:183028615:8VSB:4128:4129:1
> HCCN:183028615:8VSB:4130:4131:2
> CVTV:183028615:8VSB:4640:4641:3
> WSTV:183028615:8VSB:80:89:4
> KTBN-DT 1:527028615:8VSB:49:52:3
> KTBN-DT 2:527028615:8VSB:65:68:4
> KTBN-DT 3:527028615:8VSB:81:84:5
> KTBN-DT 4:527028615:8VSB:97:100:6
> KTBN-DT 5:527028615:8VSB:113:116:7
> TeleFutura:563028615:8VSB:49:52:3
> KTLA-DT:575028615:8VSB:49:52:3
> KDOC-HD:581028615:8VSB:49:52:1
> KDOCSD1:581028615:8VSB:65:68:2
> [0004]:581028615:8VSB:81:84:4
> KDOCSD2:581028615:8VSB:81:84:3
> Univision:599028615:8VSB:49:52:3
> NBC-4LA:605028615:8VSB:49:52:3
> WX-Plus:605028615:8VSB:65:68:4
> NewsRaw:605028615:8VSB:81:84:5
> ION:617028615:8VSB:49:52:3
> KPXN qubo:617028615:8VSB:65:68:4
> IONLife:617028615:8VSB:81:84:5
> Worship:617028615:8VSB:97:100:6
> KVEA-HD:623028615:8VSB:49:52:3
> KVEA-SD:623028615:8VSB:65:68:4
> KLCS-DT:635028615:8VSB:49:52:2
> KLCS-DT:635028615:8VSB:65:68:3
> KLCS-DT:635028615:8VSB:81:84:4
> KLCS-DT:635028615:8VSB:97:100:5
> [0006]:635028615:8VSB:113:116:6
> KWHY-HD:641028615:8VSB:49:52:3
> KWHY-SD:641028615:8VSB:65:68:4
> KCAL-DT:647028615:8VSB:49:52:1
> KAZA-DT:671028615:8VSB:49:52:3
> KAZA-TV:671028615:8VSB:0:0:65535
> KOCE-HD:677028615:8VSB:49:52:3
> KOCE-OC:677028615:8VSB:65:68:4
> KOCE-SD:677028615:8VSB:81:84:5
> Daystar:677028615:8VSB:97:100:6
> KOCE-TV:677028615:8VSB:0:0:65535
> KJLA-DT:683028615:8VSB:49:52:3
> KXLA-DT:683028615:8VSB:65:68:4
> KVMD-DT:683028615:8VSB:81:84:5
> LATV:683028615:8VSB:97:100:6
> KXLA-DT:695028615:8VSB:49:52:3
> KVMD-DT:695028615:8VSB:65:68:4
> KABC-DT:707028615:8VSB:49:52:1
> KABC-SD:707028615:8VSB:65:68:2
> KABC-WN:707028615:8VSB:81:84:3
> KCET-HD:743028615:8VSB:49:52:1
> KCET-OC:743028615:8VSB:97:100:2
> KCET-Vm:743028615:8VSB:81:84:3
> KCET-W:743028615:8VSB:65:68:4
> [0009]:743028615:8VSB:0:0:9
> [000a]:743028615:8VSB:0:0:10
> KCBS-DT:749028615:8VSB:49:52:1
> LA18.1:755028615:8VSB:49:52:1
> LA18.8:755028615:8VSB:161:164:8
> LA18.5:755028615:8VSB:113:116:5
> LA18.7:755028615:8VSB:145:148:7
> LA18.3:755028615:8VSB:81:84:3
> LA18.6:755028615:8VSB:129:132:6
> LA18:755028615:8VSB:0:0:65535
> KTTV DT:779028615:8VSB:49:52:3
> KCOP DT:785028615:8VSB:49:52:3
> KRCA-DT:797028615:8VSB:49:52:1
> KRCA-DT:797028615:8VSB:65:68:2
>
> Thanks again for the help!
> --James Evans
>
Add this:
test:779000000:8VSB:49:52:3
And try azap -r test
Better?
- Steve
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [linux-dvb] DVICO FusionHDTV5 Express Support
2008-09-23 0:22 ` Steven Toth
@ 2008-09-23 14:48 ` James Evans
2008-09-23 15:09 ` [linux-dvb] [TESTERS REQUIRED] " Steven Toth
0 siblings, 1 reply; 8+ messages in thread
From: James Evans @ 2008-09-23 14:48 UTC (permalink / raw)
To: 'Steven Toth'; +Cc: linux-dvb
The results are listed at the bottom:
> >>>> Debug looks OK. If you have another board where you know for certain
> >>>> that tuning a specific 8VSB frequency works, then tuning this same
> >>>> frequency with the LG should probably work reliably.
> >>> The installed Airstar HD5000 cards both have an LG tuner and can tune perfectly fine.
> >> OK, pick a single frequency and focus on always tuning that for the time
> >> being with the Express card.
> >
> > HD5000 Results:
> > % /usr/bin/azap -a 1 -r -c ~/.azap/channels.conf "KTTV DT"
> > using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'
> > tuning to 779028615 Hz
> > video pid 0x0031, audio pid 0x0034
> > status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> > status 1e | signal c6ce | snr 1b2e | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> > status 1e | signal e4e6 | snr 1f4b | ber 00000000 | unc 0000003d | FE_HAS_LOCK
> > status 1e | signal e1b8 | snr 1edc | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> > status 1e | signal e86e | snr 1fc7 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> > status 1e | signal e86e | snr 1fc7 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> > status 1e | signal daef | snr 1dee | ber 00000000 | unc 00000000 | FE_HAS_LOCK
> > ^C
> >
> > FusionHDTV5 Results:
> > % /usr/bin/azap -a 0 -r -c ~/.azap/channels.conf "KTTV DT"
> > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> > tuning to 779028615 Hz
> > video pid 0x0031, audio pid 0x0034
> > status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> > status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> > status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> > status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> > status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> > status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> > status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> > status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> > status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> > status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> > ^C
> >
> >>>> In terms of the tuner-to-demod, are you confident that the I/F is set
> >>>> correctly? (And inversion for that matter?)
> >>> I am not sure I understand the above question. How would I go about setting up the interface for
> >> the tuner-to-demod?
> >>
> >> /me checks the code and thinks it should be working fine.
> >>
> >> Specifically, please list here the frequencies that lock reliably for
> >> you on 8VSB with other boards. I've seen issues in the past (mainly due
> >> to driver issues) where channels tables work reliably for one tuner but
> >> not for another.
> >
> > Here is the working table that the HD5000 boards are using.
> >
> > KFLA-LD:183028615:8VSB:4128:4129:1
> > HCCN:183028615:8VSB:4130:4131:2
> > CVTV:183028615:8VSB:4640:4641:3
> > WSTV:183028615:8VSB:80:89:4
> > KTBN-DT 1:527028615:8VSB:49:52:3
> > KTBN-DT 2:527028615:8VSB:65:68:4
> > KTBN-DT 3:527028615:8VSB:81:84:5
> > KTBN-DT 4:527028615:8VSB:97:100:6
> > KTBN-DT 5:527028615:8VSB:113:116:7
> > TeleFutura:563028615:8VSB:49:52:3
> > KTLA-DT:575028615:8VSB:49:52:3
> > KDOC-HD:581028615:8VSB:49:52:1
> > KDOCSD1:581028615:8VSB:65:68:2
> > [0004]:581028615:8VSB:81:84:4
> > KDOCSD2:581028615:8VSB:81:84:3
> > Univision:599028615:8VSB:49:52:3
> > NBC-4LA:605028615:8VSB:49:52:3
> > WX-Plus:605028615:8VSB:65:68:4
> > NewsRaw:605028615:8VSB:81:84:5
> > ION:617028615:8VSB:49:52:3
> > KPXN qubo:617028615:8VSB:65:68:4
> > IONLife:617028615:8VSB:81:84:5
> > Worship:617028615:8VSB:97:100:6
> > KVEA-HD:623028615:8VSB:49:52:3
> > KVEA-SD:623028615:8VSB:65:68:4
> > KLCS-DT:635028615:8VSB:49:52:2
> > KLCS-DT:635028615:8VSB:65:68:3
> > KLCS-DT:635028615:8VSB:81:84:4
> > KLCS-DT:635028615:8VSB:97:100:5
> > [0006]:635028615:8VSB:113:116:6
> > KWHY-HD:641028615:8VSB:49:52:3
> > KWHY-SD:641028615:8VSB:65:68:4
> > KCAL-DT:647028615:8VSB:49:52:1
> > KAZA-DT:671028615:8VSB:49:52:3
> > KAZA-TV:671028615:8VSB:0:0:65535
> > KOCE-HD:677028615:8VSB:49:52:3
> > KOCE-OC:677028615:8VSB:65:68:4
> > KOCE-SD:677028615:8VSB:81:84:5
> > Daystar:677028615:8VSB:97:100:6
> > KOCE-TV:677028615:8VSB:0:0:65535
> > KJLA-DT:683028615:8VSB:49:52:3
> > KXLA-DT:683028615:8VSB:65:68:4
> > KVMD-DT:683028615:8VSB:81:84:5
> > LATV:683028615:8VSB:97:100:6
> > KXLA-DT:695028615:8VSB:49:52:3
> > KVMD-DT:695028615:8VSB:65:68:4
> > KABC-DT:707028615:8VSB:49:52:1
> > KABC-SD:707028615:8VSB:65:68:2
> > KABC-WN:707028615:8VSB:81:84:3
> > KCET-HD:743028615:8VSB:49:52:1
> > KCET-OC:743028615:8VSB:97:100:2
> > KCET-Vm:743028615:8VSB:81:84:3
> > KCET-W:743028615:8VSB:65:68:4
> > [0009]:743028615:8VSB:0:0:9
> > [000a]:743028615:8VSB:0:0:10
> > KCBS-DT:749028615:8VSB:49:52:1
> > LA18.1:755028615:8VSB:49:52:1
> > LA18.8:755028615:8VSB:161:164:8
> > LA18.5:755028615:8VSB:113:116:5
> > LA18.7:755028615:8VSB:145:148:7
> > LA18.3:755028615:8VSB:81:84:3
> > LA18.6:755028615:8VSB:129:132:6
> > LA18:755028615:8VSB:0:0:65535
> > KTTV DT:779028615:8VSB:49:52:3
> > KCOP DT:785028615:8VSB:49:52:3
> > KRCA-DT:797028615:8VSB:49:52:1
> > KRCA-DT:797028615:8VSB:65:68:2
> >
> > Thanks again for the help!
> > --James Evans
> >
>
> Add this:
>
> test:779000000:8VSB:49:52:3
>
> And try azap -r test
>
> Better?
% azap -a 0 -r "test"
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
tuning to 779000000 Hz
video pid 0x0031, audio pid 0x0034
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
^C
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 8+ messages in thread
* [linux-dvb] [TESTERS REQUIRED] Re: DVICO FusionHDTV5 Express Support
2008-09-23 14:48 ` James Evans
@ 2008-09-23 15:09 ` Steven Toth
0 siblings, 0 replies; 8+ messages in thread
From: Steven Toth @ 2008-09-23 15:09 UTC (permalink / raw)
To: James Evans, linux-dvb
James Evans wrote:
> The results are listed at the bottom:
>
>>>>>> Debug looks OK. If you have another board where you know for certain
>>>>>> that tuning a specific 8VSB frequency works, then tuning this same
>>>>>> frequency with the LG should probably work reliably.
>>>>> The installed Airstar HD5000 cards both have an LG tuner and can tune perfectly fine.
>>>> OK, pick a single frequency and focus on always tuning that for the time
>>>> being with the Express card.
>>> HD5000 Results:
>>> % /usr/bin/azap -a 1 -r -c ~/.azap/channels.conf "KTTV DT"
>>> using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'
>>> tuning to 779028615 Hz
>>> video pid 0x0031, audio pid 0x0034
>>> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
>>> status 1e | signal c6ce | snr 1b2e | ber 00000000 | unc 00000000 | FE_HAS_LOCK
>>> status 1e | signal e4e6 | snr 1f4b | ber 00000000 | unc 0000003d | FE_HAS_LOCK
>>> status 1e | signal e1b8 | snr 1edc | ber 00000000 | unc 00000000 | FE_HAS_LOCK
>>> status 1e | signal e86e | snr 1fc7 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
>>> status 1e | signal e86e | snr 1fc7 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
>>> status 1e | signal daef | snr 1dee | ber 00000000 | unc 00000000 | FE_HAS_LOCK
>>> ^C
>>>
>>> FusionHDTV5 Results:
>>> % /usr/bin/azap -a 0 -r -c ~/.azap/channels.conf "KTTV DT"
>>> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
>>> tuning to 779028615 Hz
>>> video pid 0x0031, audio pid 0x0034
>>> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
>>> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
>>> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
>>> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
>>> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
>>> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
>>> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
>>> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
>>> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
>>> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
>>> ^C
>>>
>>>>>> In terms of the tuner-to-demod, are you confident that the I/F is set
>>>>>> correctly? (And inversion for that matter?)
>>>>> I am not sure I understand the above question. How would I go about setting up the interface for
>>>> the tuner-to-demod?
>>>>
>>>> /me checks the code and thinks it should be working fine.
>>>>
>>>> Specifically, please list here the frequencies that lock reliably for
>>>> you on 8VSB with other boards. I've seen issues in the past (mainly due
>>>> to driver issues) where channels tables work reliably for one tuner but
>>>> not for another.
>>> Here is the working table that the HD5000 boards are using.
>>>
>>> KFLA-LD:183028615:8VSB:4128:4129:1
>>> HCCN:183028615:8VSB:4130:4131:2
>>> CVTV:183028615:8VSB:4640:4641:3
>>> WSTV:183028615:8VSB:80:89:4
>>> KTBN-DT 1:527028615:8VSB:49:52:3
>>> KTBN-DT 2:527028615:8VSB:65:68:4
>>> KTBN-DT 3:527028615:8VSB:81:84:5
>>> KTBN-DT 4:527028615:8VSB:97:100:6
>>> KTBN-DT 5:527028615:8VSB:113:116:7
>>> TeleFutura:563028615:8VSB:49:52:3
>>> KTLA-DT:575028615:8VSB:49:52:3
>>> KDOC-HD:581028615:8VSB:49:52:1
>>> KDOCSD1:581028615:8VSB:65:68:2
>>> [0004]:581028615:8VSB:81:84:4
>>> KDOCSD2:581028615:8VSB:81:84:3
>>> Univision:599028615:8VSB:49:52:3
>>> NBC-4LA:605028615:8VSB:49:52:3
>>> WX-Plus:605028615:8VSB:65:68:4
>>> NewsRaw:605028615:8VSB:81:84:5
>>> ION:617028615:8VSB:49:52:3
>>> KPXN qubo:617028615:8VSB:65:68:4
>>> IONLife:617028615:8VSB:81:84:5
>>> Worship:617028615:8VSB:97:100:6
>>> KVEA-HD:623028615:8VSB:49:52:3
>>> KVEA-SD:623028615:8VSB:65:68:4
>>> KLCS-DT:635028615:8VSB:49:52:2
>>> KLCS-DT:635028615:8VSB:65:68:3
>>> KLCS-DT:635028615:8VSB:81:84:4
>>> KLCS-DT:635028615:8VSB:97:100:5
>>> [0006]:635028615:8VSB:113:116:6
>>> KWHY-HD:641028615:8VSB:49:52:3
>>> KWHY-SD:641028615:8VSB:65:68:4
>>> KCAL-DT:647028615:8VSB:49:52:1
>>> KAZA-DT:671028615:8VSB:49:52:3
>>> KAZA-TV:671028615:8VSB:0:0:65535
>>> KOCE-HD:677028615:8VSB:49:52:3
>>> KOCE-OC:677028615:8VSB:65:68:4
>>> KOCE-SD:677028615:8VSB:81:84:5
>>> Daystar:677028615:8VSB:97:100:6
>>> KOCE-TV:677028615:8VSB:0:0:65535
>>> KJLA-DT:683028615:8VSB:49:52:3
>>> KXLA-DT:683028615:8VSB:65:68:4
>>> KVMD-DT:683028615:8VSB:81:84:5
>>> LATV:683028615:8VSB:97:100:6
>>> KXLA-DT:695028615:8VSB:49:52:3
>>> KVMD-DT:695028615:8VSB:65:68:4
>>> KABC-DT:707028615:8VSB:49:52:1
>>> KABC-SD:707028615:8VSB:65:68:2
>>> KABC-WN:707028615:8VSB:81:84:3
>>> KCET-HD:743028615:8VSB:49:52:1
>>> KCET-OC:743028615:8VSB:97:100:2
>>> KCET-Vm:743028615:8VSB:81:84:3
>>> KCET-W:743028615:8VSB:65:68:4
>>> [0009]:743028615:8VSB:0:0:9
>>> [000a]:743028615:8VSB:0:0:10
>>> KCBS-DT:749028615:8VSB:49:52:1
>>> LA18.1:755028615:8VSB:49:52:1
>>> LA18.8:755028615:8VSB:161:164:8
>>> LA18.5:755028615:8VSB:113:116:5
>>> LA18.7:755028615:8VSB:145:148:7
>>> LA18.3:755028615:8VSB:81:84:3
>>> LA18.6:755028615:8VSB:129:132:6
>>> LA18:755028615:8VSB:0:0:65535
>>> KTTV DT:779028615:8VSB:49:52:3
>>> KCOP DT:785028615:8VSB:49:52:3
>>> KRCA-DT:797028615:8VSB:49:52:1
>>> KRCA-DT:797028615:8VSB:65:68:2
>>>
>>> Thanks again for the help!
>>> --James Evans
>>>
>> Add this:
>>
>> test:779000000:8VSB:49:52:3
>>
>> And try azap -r test
>>
>> Better?
>
> % azap -a 0 -r "test"
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> tuning to 779000000 Hz
> video pid 0x0031, audio pid 0x0034
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
> status 00 | signal 0000 | snr 0000 | ber 00000000 | unc 00000000 |
We either have a massive regression in support for this card or
something is sick in your environment.
Everyone,
Is anyone else using the current master repo with the HDTV5 Express?
Or, can someone please pull master and test it.
Thanks,
Steve
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2008-09-23 15:10 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-09-22 3:44 [linux-dvb] DVICO FusionHDTV5 Express Support James Evans
2008-09-22 4:00 ` Steven Toth
2008-09-22 4:26 ` James Evans
2008-09-22 5:02 ` Steven Toth
2008-09-22 23:27 ` James Evans
2008-09-23 0:22 ` Steven Toth
2008-09-23 14:48 ` James Evans
2008-09-23 15:09 ` [linux-dvb] [TESTERS REQUIRED] " Steven Toth
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox