* Re: [linux-dvb] Compro VideoMate E600F analog PCIe TV/FM capture card
@ 2008-09-29 6:47 stev391
2008-09-29 18:13 ` Steven Toth
0 siblings, 1 reply; 6+ messages in thread
From: stev391 @ 2008-09-29 6:47 UTC (permalink / raw)
To: Marek Marek; +Cc: linux-dvb
> I have Compro VideoMate E600F analog PCIe TV/FM capture card with MPEG II A/V Encoder. I use
> Gentoo 2008.0 with 2.6.25-gentoo-r7 x86_64 kernel. There's no any support for this card on the
> V4L/DVB repository yet, so anybody help me?
>
> lspci -vvnn
> 02:00.0 Multimedia video controller [0400]: Conexant Device [14f1:8852] (rev 02)
> Subsystem: Compro Technology, Inc. Device [185b:e800]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
> FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
> <PERR- INTx-
> Latency: 0, Cache Line Size: 4 bytes
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at fd600000 (64-bit, non-prefetchable) [size=2M]
> Capabilities: [40] Express (v1) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <2us, L1 <4us
> ClockPM- Suprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-
> ABWMgmt-
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [90] Vital Product Data <?>
> Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
> Address: 0000000000000000 Data: 0000
> Capabilities: [100] Advanced Error Reporting <?>
> Capabilities: [200] Virtual Channel <?>
>
> dmesg
> cx23885 driver version 0.0.1 loaded
> ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
> cx23885[0]: Your board isn't known (yet) to the driver. You can
> cx23885[0]: try to pick one of the existing card configs via
> cx23885[0]: card=<n> insmod option. Updating to the latest
> cx23885[0]: version might help as well.
> cx23885[0]: Here is a list of valid choices for the card=<n> insmod option:
> cx23885[0]: card=0 -> UNKNOWN/GENERIC
> cx23885[0]: card=1 -> Hauppauge WinTV-HVR1800lp
> cx23885[0]: card=2 -> Hauppauge WinTV-HVR1800
> cx23885[0]: card=3 -> Hauppauge WinTV-HVR1250
> cx23885[0]: card=4 -> DViCO FusionHDTV5 Express
> cx23885[0]: card=5 -> Hauppauge WinTV-HVR1500Q
> cx23885[0]: card=6 -> Hauppauge WinTV-HVR1500
> cx23885[0]: card=7 -> Hauppauge WinTV-HVR1200
> cx23885[0]: card=8 -> Hauppauge WinTV-HVR1700
> cx23885[0]: card=9 -> Hauppauge WinTV-HVR1400
> cx23885[0]: card=10 -> DViCO FusionHDTV7 Dual Express
> cx23885[0]: card=11 -> DViCO FusionHDTV DVB-T Dual Express
> cx23885[0]: card=12 -> Leadtek Winfast PxDVR3200 H
> CORE cx23885[0]: subsystem: 185b:e800, board: UNKNOWN/GENERIC [card=0,autodetected]
> cx23885[0]: i2c bus 0 registered
> cx23885[0]: i2c bus 1 registered
> cx23885[0]: i2c bus 2 registered
> cx23885_dev_checkrevision() Hardware revision = 0xb0
> cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 16, latency: 0, mmio: 0xfd600000
> PCI: Setting latency timer of device 0000:02:00.0 to 64
>
> Conexant CX23885-13Z PCIe A/V Decoder
> Conexant CX23417-11Z MPEG II A/V Encoder
> XCeive XC2028ACQ Video Tuner
>
> Detailed specification is on http://linuxtv.org/wiki/index.php/Compro_VideoMate_E600F
>
> Thanks for any help.
>
> Marek Wasilow
>
> PS: Sorry for my poor english...
Marek,
At the moment there no support for this card (As you have found out already).
No one has mentioned adding support for this card yet. However you have already started gathering the required items for adding support (as on the wiki page)
See the other VideoMate cards in the wiki for what else is required. I have added support to the DVB side of the other VideoMate cards in a patch. However due to some of the items in the patch that worked, but cannot be explained, this patch has not been incorporated to the main DVB drivers.
I do intend in the future to look at the analog side of these cards. However the Leadtek PVR3200H will be the first that I will get the analog going on. However I have been very busy lately and have not had a chance to look into.
Other items that you could include on the wiki page:
* eeprom dump (read this http://www.linuxtv.org/pipermail/linux-dvb/2008-September/028529.html)
* regspy dump of all registers in all states (It is Steven Toths DScaler Regspy version that you require)
* i2c scan see the other Compro VideoMate wiki pages.
Thanks again for creating the wiki page and contacting the mailing list. When I get around to adding support I will try to remember your email address, if not just check the mailing list. If you want to add support check out the http://linuxtv.org/hg/~stoth/cx23885-audio/ add look at the recent changes. This will give you an idea of what is required.
Regards,
Stephen.
--
Be Yourself @ mail.com!
Choose From 200+ Email Addresses
Get a Free Account at www.mail.com
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] Compro VideoMate E600F analog PCIe TV/FM capture card
2008-09-29 6:47 [linux-dvb] Compro VideoMate E600F analog PCIe TV/FM capture card stev391
@ 2008-09-29 18:13 ` Steven Toth
0 siblings, 0 replies; 6+ messages in thread
From: Steven Toth @ 2008-09-29 18:13 UTC (permalink / raw)
To: Marek Marek; +Cc: linux-dvb, stev391
stev391@email.com wrote:
>> I have Compro VideoMate E600F analog PCIe TV/FM capture card with MPEG II A/V Encoder. I use
>> Gentoo 2008.0 with 2.6.25-gentoo-r7 x86_64 kernel. There's no any support for this card on the
>> V4L/DVB repository yet, so anybody help me?
>>
>> lspci -vvnn
>> 02:00.0 Multimedia video controller [0400]: Conexant Device [14f1:8852] (rev 02)
>> Subsystem: Compro Technology, Inc. Device [185b:e800]
>> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR-
>> FastB2B- DisINTx-
>> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
>> <PERR- INTx-
>> Latency: 0, Cache Line Size: 4 bytes
>> Interrupt: pin A routed to IRQ 5
>> Region 0: Memory at fd600000 (64-bit, non-prefetchable) [size=2M]
>> Capabilities: [40] Express (v1) Endpoint, MSI 00
>> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
>> ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
>> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
>> RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
>> MaxPayload 128 bytes, MaxReadReq 512 bytes
>> DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
>> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <2us, L1 <4us
>> ClockPM- Suprise- LLActRep- BwNot-
>> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
>> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt-
>> ABWMgmt-
>> Capabilities: [80] Power Management version 2
>> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
>> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>> Capabilities: [90] Vital Product Data <?>
>> Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
>> Address: 0000000000000000 Data: 0000
>> Capabilities: [100] Advanced Error Reporting <?>
>> Capabilities: [200] Virtual Channel <?>
>>
>> dmesg
>> cx23885 driver version 0.0.1 loaded
>> ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
>> cx23885[0]: Your board isn't known (yet) to the driver. You can
>> cx23885[0]: try to pick one of the existing card configs via
>> cx23885[0]: card=<n> insmod option. Updating to the latest
>> cx23885[0]: version might help as well.
>> cx23885[0]: Here is a list of valid choices for the card=<n> insmod option:
>> cx23885[0]: card=0 -> UNKNOWN/GENERIC
>> cx23885[0]: card=1 -> Hauppauge WinTV-HVR1800lp
>> cx23885[0]: card=2 -> Hauppauge WinTV-HVR1800
>> cx23885[0]: card=3 -> Hauppauge WinTV-HVR1250
>> cx23885[0]: card=4 -> DViCO FusionHDTV5 Express
>> cx23885[0]: card=5 -> Hauppauge WinTV-HVR1500Q
>> cx23885[0]: card=6 -> Hauppauge WinTV-HVR1500
>> cx23885[0]: card=7 -> Hauppauge WinTV-HVR1200
>> cx23885[0]: card=8 -> Hauppauge WinTV-HVR1700
>> cx23885[0]: card=9 -> Hauppauge WinTV-HVR1400
>> cx23885[0]: card=10 -> DViCO FusionHDTV7 Dual Express
>> cx23885[0]: card=11 -> DViCO FusionHDTV DVB-T Dual Express
>> cx23885[0]: card=12 -> Leadtek Winfast PxDVR3200 H
>> CORE cx23885[0]: subsystem: 185b:e800, board: UNKNOWN/GENERIC [card=0,autodetected]
>> cx23885[0]: i2c bus 0 registered
>> cx23885[0]: i2c bus 1 registered
>> cx23885[0]: i2c bus 2 registered
>> cx23885_dev_checkrevision() Hardware revision = 0xb0
>> cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 16, latency: 0, mmio: 0xfd600000
>> PCI: Setting latency timer of device 0000:02:00.0 to 64
>>
>> Conexant CX23885-13Z PCIe A/V Decoder
>> Conexant CX23417-11Z MPEG II A/V Encoder
>> XCeive XC2028ACQ Video Tuner
>>
>> Detailed specification is on http://linuxtv.org/wiki/index.php/Compro_VideoMate_E600F
>>
>> Thanks for any help.
>>
>> Marek Wasilow
>>
>> PS: Sorry for my poor english...
>
> Marek,
>
> At the moment there no support for this card (As you have found out already).
>
> No one has mentioned adding support for this card yet. However you have already started gathering the required items for adding support (as on the wiki page)
>
> See the other VideoMate cards in the wiki for what else is required. I have added support to the DVB side of the other VideoMate cards in a patch. However due to some of the items in the patch that worked, but cannot be explained, this patch has not been incorporated to the main DVB drivers.
>
> I do intend in the future to look at the analog side of these cards. However the Leadtek PVR3200H will be the first that I will get the analog going on. However I have been very busy lately and have not had a chance to look into.
>
> Other items that you could include on the wiki page:
> * eeprom dump (read this http://www.linuxtv.org/pipermail/linux-dvb/2008-September/028529.html)
> * regspy dump of all registers in all states (It is Steven Toths DScaler Regspy version that you require)
> * i2c scan see the other Compro VideoMate wiki pages.
>
> Thanks again for creating the wiki page and contacting the mailing list. When I get around to adding support I will try to remember your email address, if not just check the mailing list. If you want to add support check out the http://linuxtv.org/hg/~stoth/cx23885-audio/ add look at the recent changes. This will give you an idea of what is required.
Marek, Mauro has sent me your email details directly. I replied to with
some detailed instructions which you never replied to. I then received
your second email asking for information, which I replied to again.
You obviously didn't see either email. I asked Mauro to forward my
emails to you directly, thinking that perhaps your ISP blacklisted my ISP.
You never got any of these emails?
- Steve
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] Compro VideoMate E600F analog PCIe TV/FM capture card
@ 2008-09-29 19:09 Marek Marek
2008-09-29 19:24 ` Steven Toth
0 siblings, 1 reply; 6+ messages in thread
From: Marek Marek @ 2008-09-29 19:09 UTC (permalink / raw)
To: stoth; +Cc: linux-dvb, stev391
At the begining I am sorry for misunderstanding... This account was created specially for v4l-dvb mailing list. I got the previous email from you today so could not answer on it yet. There wasn't any others emails from you eariel in my mailbox.
> > Other items that you could include on the wiki page:
> > * eeprom dump (read this
> http://www.linuxtv.org/pipermail/linux-dvb/2008-September/028529.html)
> > * regspy dump of all registers in all states (It is
> Steven Toths DScaler Regspy version that you require)
> > * i2c scan see the other Compro VideoMate wiki pages.
> >
As you asked I included some new information about my card on wiki page. The RegSpy output I will include later when install winxp. If those information are correct that's good if not I will be grateful you will tell me that.
Me and my broken english... sorry guy's :)
I do my best. Forgive me these problems.
Marek Wasilow
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: [linux-dvb] Compro VideoMate E600F analog PCIe TV/FM capture card
2008-09-29 19:09 Marek Marek
@ 2008-09-29 19:24 ` Steven Toth
2008-09-30 18:10 ` Marek Marek
0 siblings, 1 reply; 6+ messages in thread
From: Steven Toth @ 2008-09-29 19:24 UTC (permalink / raw)
To: albatrosmwdvb; +Cc: linux-dvb, stev391
Marek Marek wrote:
> At the begining I am sorry for misunderstanding... This account was created specially for v4l-dvb mailing list. I got the previous email from you today so could not answer on it yet. There wasn't any others emails from you eariel in my mailbox.
>
>>> Other items that you could include on the wiki page:
>>> * eeprom dump (read this
>> http://www.linuxtv.org/pipermail/linux-dvb/2008-September/028529.html)
>>> * regspy dump of all registers in all states (It is
>> Steven Toths DScaler Regspy version that you require)
>>> * i2c scan see the other Compro VideoMate wiki pages.
>>>
>
> As you asked I included some new information about my card on wiki page. The RegSpy output I will include later when install winxp. If those information are correct that's good if not I will be grateful you will tell me that.
>
> Me and my broken english... sorry guy's :)
> I do my best. Forgive me these problems.
:) No problem! I wanted to make sure you'd seen my original response.
If you can get some regspy dumps, some i2c scan details and pictures of
the silicon on the wiki then we have a good chance of adding support for
you.
- Steve
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 6+ messages in thread
* [linux-dvb] Compro VideoMate E600F analog PCIe TV/FM capture card
@ 2008-09-26 18:56 Marek Marek
0 siblings, 0 replies; 6+ messages in thread
From: Marek Marek @ 2008-09-26 18:56 UTC (permalink / raw)
To: linux-dvb
I have Compro VideoMate E600F analog PCIe TV/FM capture card with MPEG II A/V Encoder. I use Gentoo 2008.0 with 2.6.25-gentoo-r7 x86_64 kernel. There's no any support for this card on the V4L/DVB repository yet, so anybody help me?
lspci -vvnn
02:00.0 Multimedia video controller [0400]: Conexant Device [14f1:8852] (rev 02)
Subsystem: Compro Technology, Inc. Device [185b:e800]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fd600000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [40] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <2us, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Vital Product Data <?>
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [200] Virtual Channel <?>
dmesg
cx23885 driver version 0.0.1 loaded
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
cx23885[0]: Your board isn't known (yet) to the driver. You can
cx23885[0]: try to pick one of the existing card configs via
cx23885[0]: card=<n> insmod option. Updating to the latest
cx23885[0]: version might help as well.
cx23885[0]: Here is a list of valid choices for the card=<n> insmod option:
cx23885[0]: card=0 -> UNKNOWN/GENERIC
cx23885[0]: card=1 -> Hauppauge WinTV-HVR1800lp
cx23885[0]: card=2 -> Hauppauge WinTV-HVR1800
cx23885[0]: card=3 -> Hauppauge WinTV-HVR1250
cx23885[0]: card=4 -> DViCO FusionHDTV5 Express
cx23885[0]: card=5 -> Hauppauge WinTV-HVR1500Q
cx23885[0]: card=6 -> Hauppauge WinTV-HVR1500
cx23885[0]: card=7 -> Hauppauge WinTV-HVR1200
cx23885[0]: card=8 -> Hauppauge WinTV-HVR1700
cx23885[0]: card=9 -> Hauppauge WinTV-HVR1400
cx23885[0]: card=10 -> DViCO FusionHDTV7 Dual Express
cx23885[0]: card=11 -> DViCO FusionHDTV DVB-T Dual Express
cx23885[0]: card=12 -> Leadtek Winfast PxDVR3200 H
CORE cx23885[0]: subsystem: 185b:e800, board: UNKNOWN/GENERIC [card=0,autodetected]
cx23885[0]: i2c bus 0 registered
cx23885[0]: i2c bus 1 registered
cx23885[0]: i2c bus 2 registered
cx23885_dev_checkrevision() Hardware revision = 0xb0
cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 16, latency: 0, mmio: 0xfd600000
PCI: Setting latency timer of device 0000:02:00.0 to 64
Conexant CX23885-13Z PCIe A/V Decoder
Conexant CX23417-11Z MPEG II A/V Encoder
XCeive XC2028ACQ Video Tuner
Detailed specification is on http://linuxtv.org/wiki/index.php/Compro_VideoMate_E600F
Thanks for any help.
Marek Wasilow
PS: Sorry for my poor english...
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2008-09-30 18:11 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-09-29 6:47 [linux-dvb] Compro VideoMate E600F analog PCIe TV/FM capture card stev391
2008-09-29 18:13 ` Steven Toth
-- strict thread matches above, loose matches on Subject: below --
2008-09-29 19:09 Marek Marek
2008-09-29 19:24 ` Steven Toth
2008-09-30 18:10 ` Marek Marek
2008-09-26 18:56 Marek Marek
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox