From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from nf-out-0910.google.com ([64.233.182.189]) by www.linuxtv.org with esmtp (Exim 4.63) (envelope-from ) id 1Kl4iL-0004ib-TU for linux-dvb@linuxtv.org; Wed, 01 Oct 2008 18:38:16 +0200 Received: by nf-out-0910.google.com with SMTP id g13so283192nfb.11 for ; Wed, 01 Oct 2008 09:38:09 -0700 (PDT) Message-ID: <48E3A767.2020706@gmail.com> Date: Wed, 01 Oct 2008 18:37:59 +0200 From: "tomlohave@gmail.com" MIME-Version: 1.0 To: dabby bentam References: In-Reply-To: Cc: linux-dvb@linuxtv.org Subject: Re: [linux-dvb] Adding remote support to Avermedia Super 007 - more info needed! List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Sender: linux-dvb-bounces@linuxtv.org Errors-To: linux-dvb-bounces+mchehab=infradead.org@linuxtv.org List-ID: dabby bentam a =E9crit : > -----Original Message----- > From: darron@kewl.org [mailto:darron@kewl.org] > Sent: 01 October 2008 02:08 > To: dabby bentam > Subject: Re: [linux-dvb] Adding remote support to Avermedia Super 007 = > - more info needed! > > In message , dabby bentam = > wrote: > > hello david > > >I'm currently trying to get remote support added to the Avermedia Super > >007=3D card. > > I have one of these cards also but I have no good news for you = > unfortunately. > > I am replying just to confirm that I too saw no activity in the = > register logs in XP when pressing remote key presses. Nor, from what I = > can see will any additions to the saa7134 code as is, aide you in = > reaching remote control nirvana. > > It looks as if all remotes on the saa7134 linux driver thus far are = > triggered via an interrupt and that no such interrupt is occuring when = > you press a key on the remote for that board. This may require more = > absolute confirmation though as I didn't spend a great deal of time = > looking. > > >I've turned the ir_debug on and gpio tracking on and enabled i2c_scan. > >I've=3D added an entry in the saa7134-cards.c and saa7134-input.c - > >copying the se=3D ttings from other avermedia cards. > > > >The polling setting makes the card print out loads of ir_builder > >settings=3D =3D2C removing the setting no output! - from this i am assum= ing > >that this car=3D d has no gpio setting? - possible i2c? > > > >I've used regspy (from dscaler) to determine the GPIO STATUS and MASK > >value=3D . Turning on/off the remote in windows has no value change? - > >does it chang=3D e? > > > >Any guidance on how to determine the ir code? - without the manufacture > >cod=3D e book. > > I took a photo but didn't identify all the ICs on the board and write = > them down, it may be worthwhie doing so and also tracing from where = > the IR detector comes into the card and where it actually ends up. > > If you are determined then you could explore the above but there is = > still no guarantee of any eventual success of course as just knowing = > about it more is only the first step in actually getting it to work. > > cya! > > Hello darron, > > Thanks for the reply. I've established the cards IR port is not GPIO = > but I2C. Similar to the hvr-1110 card. The I2C readout gives me:- > > 0x10 > 0x96 > > From the other I2C cards, these functions are used to enable/disable = > the IR port. > > I'll take a closer look at he pins just incase. > > Thanks > > David > > > ------------------------------------------------------------------------ Have you try with i2c_scan ? Not sure but for hvr1110, >/ saa7133[0]: i2c scan: found device @ 0x10 [???] />/ saa7133[0]: i2c scan: found device @ 0x96 [???] />/ saa7133[0]: i2c scan: found device @ 0xa0 [eeprom] />/ saa7133[0]: i2c scan: found device @ 0xe0 [???] />/ saa7133[0]: i2c scan: found device @ 0xe2 [???] <---- ir remot= e here />/ saa7133[0]: i2c scan: found device @ 0xe4 [???] />/ saa7133[0]: i2c scan: found device @ 0xe6 [???] / Then 0xe2 <<1 =3D 0x71 Good luck Tom _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb