* [linux-dvb] S2API & TT3200 @ 2008-10-28 10:15 jean-paul 2008-10-28 10:24 ` oleg roitburd 2008-10-28 10:30 ` Manu Abraham 0 siblings, 2 replies; 11+ messages in thread From: jean-paul @ 2008-10-28 10:15 UTC (permalink / raw) To: linux-dvb Ok again. I using now vdr 1.7.0 and multiproto from manu to make my two tt 3200-ci working with streamdev. Vdr zapper en MPC. Its working fine except some judder but its more a vdr issue. For now I have a development system with an TT 3200 to and try to let vdr run with S2API drivers. After getting the drivers from http://mercurial.intuxication.org/hg/s2-liplianin/ the compile ends with a error: CC [M] /usr/local/src/dvb/v4l/cx88-vbi.o CC [M] /usr/local/src/dvb/v4l/cx88-mpeg.o CC [M] /usr/local/src/dvb/v4l/cx88-cards.o /usr/local/src/dvb/v4l/cx88-cards.c:2314: error: request for member 'subdevice' in something not a structure or union make[4]: *** [/usr/local/src/dvb/v4l/cx88-cards.o] Error 1 make[3]: *** [_module_/usr/local/src/dvb/v4l] Error make[2]: *** [sub-make] Error 2 make[1]: *** [all] Error 2 make[1]: Leaving directory `/usr/src/linux-2.6.25.16-0.1-obj/x86_64/default' make: *** [default] Error 2 Remove those stuff I?m not using and compile it again. Reboot the system and try to use scan-s2. Next problem. Diseqc doesn?t work anymore and I?m able to scan one transponder. Is it possible to make a list with patches and repositories I need to make it working? Regards Jean-Paul _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [linux-dvb] S2API & TT3200 2008-10-28 10:15 [linux-dvb] S2API & TT3200 jean-paul @ 2008-10-28 10:24 ` oleg roitburd 2008-10-28 10:30 ` Manu Abraham 1 sibling, 0 replies; 11+ messages in thread From: oleg roitburd @ 2008-10-28 10:24 UTC (permalink / raw) To: jean-paul; +Cc: linux-dvb 2008/10/28 <jean-paul@goedee.nl>: > Ok again. > > I using now vdr 1.7.0 and multiproto from manu to make my two tt > 3200-ci working with streamdev. Vdr zapper en MPC. Its working fine > except some judder but its more a vdr issue. > > For now I have a development system with an TT 3200 to and try to let > vdr run with S2API drivers. After getting the drivers from > http://mercurial.intuxication.org/hg/s2-liplianin/ the compile ends > with a error: > > CC [M] /usr/local/src/dvb/v4l/cx88-vbi.o > CC [M] /usr/local/src/dvb/v4l/cx88-mpeg.o > CC [M] /usr/local/src/dvb/v4l/cx88-cards.o > /usr/local/src/dvb/v4l/cx88-cards.c:2314: error: request for member > 'subdevice' in something not a structure or union > make[4]: *** [/usr/local/src/dvb/v4l/cx88-cards.o] Error 1 > make[3]: *** [_module_/usr/local/src/dvb/v4l] Error > make[2]: *** [sub-make] Error 2 > make[1]: *** [all] Error 2 > make[1]: Leaving directory `/usr/src/linux-2.6.25.16-0.1-obj/x86_64/default' > make: *** [default] Error 2 > > > Remove those stuff I?m not using and compile it again. Try this patch http://arvdr-dev.free-x.de:8080/freex-s2/raw-rev/4b6a6a9dbf85 > Reboot the > system and try to use scan-s2. Next problem. Diseqc doesn?t work > anymore and I?m able to scan one transponder. I have tried with DiseqC 1.0 It works for me ./scan-s2 -s 1 -o vdr -t 3 dvb-s/myHotbird-13.0E > ../channels.conf-13.0E HotBird is on second port ( -s 1) Regards Oleg Roitburd _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [linux-dvb] S2API & TT3200 2008-10-28 10:15 [linux-dvb] S2API & TT3200 jean-paul 2008-10-28 10:24 ` oleg roitburd @ 2008-10-28 10:30 ` Manu Abraham 2008-10-28 11:45 ` jean-paul 1 sibling, 1 reply; 11+ messages in thread From: Manu Abraham @ 2008-10-28 10:30 UTC (permalink / raw) To: jean-paul; +Cc: linux-dvb jean-paul@goedee.nl wrote: > Ok again. > > I using now vdr 1.7.0 and multiproto from manu to make my two tt > 3200-ci working with streamdev. Vdr zapper en MPC. Its working fine > except some judder but its more a vdr issue. > > For now I have a development system with an TT 3200 to and try to let > vdr run with S2API drivers. After getting the drivers from > http://mercurial.intuxication.org/hg/s2-liplianin/ the compile ends > with a error: You can simply clone http://jusst.de/hg/v4l-dvb or http://linuxtv.org/hg/v4l-dvb and check The former contains two more fixes, so better try to test with that. Regards, Manu _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [linux-dvb] S2API & TT3200 2008-10-28 10:30 ` Manu Abraham @ 2008-10-28 11:45 ` jean-paul 2008-10-28 11:53 ` oleg roitburd 0 siblings, 1 reply; 11+ messages in thread From: jean-paul @ 2008-10-28 11:45 UTC (permalink / raw) To: Manu Abraham; +Cc: linux-dvb Ok clone the repo and its compiling again. Thanx. Now I want to scan channels (scab-s2) on both lnb;s (astra 1 & 3). First transponder scans only 13 services and Diseqc doesn?t work with the second lnb. WARNING: >>> tuning failed!!! >>> tune to: 11856:vS1C56:S23.5E:27500: (tuning failed) DiSEqC: uncommitted switch pos 0 DiSEqC: switch pos 1, 13V, hiband (index 6) DVB-S IF freq is 1256000 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 WARNING: >>> tuning failed!!! ERROR: initial tuning failed dumping lists (0 services) Done. Citeren Manu Abraham <abraham.manu@gmail.com>: > jean-paul@goedee.nl wrote: >> Ok again. >> >> I using now vdr 1.7.0 and multiproto from manu to make my two tt >> 3200-ci working with streamdev. Vdr zapper en MPC. Its working fine >> except some judder but its more a vdr issue. >> >> For now I have a development system with an TT 3200 to and try to let >> vdr run with S2API drivers. After getting the drivers from >> http://mercurial.intuxication.org/hg/s2-liplianin/ the compile ends >> with a error: > > You can simply clone http://jusst.de/hg/v4l-dvb > or http://linuxtv.org/hg/v4l-dvb and check > > The former contains two more fixes, so better try to test with that. > > Regards, > Manu > _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [linux-dvb] S2API & TT3200 2008-10-28 11:45 ` jean-paul @ 2008-10-28 11:53 ` oleg roitburd 2008-10-28 11:57 ` Jaap Crezee 2008-10-28 13:15 ` jean-paul 0 siblings, 2 replies; 11+ messages in thread From: oleg roitburd @ 2008-10-28 11:53 UTC (permalink / raw) To: jean-paul; +Cc: linux-dvb, Manu Abraham 2008/10/28 <jean-paul@goedee.nl>: > Ok clone the repo and its compiling again. Thanx. Now I want to scan > channels (scab-s2) on both lnb;s (astra 1 & 3). First transponder > scans only 13 services and Diseqc doesn?t work with the second lnb. > > WARNING: >>> tuning failed!!! >>>> tune to: 11856:vS1C56:S23.5E:27500: (tuning failed) > DiSEqC: uncommitted switch pos 0 > DiSEqC: switch pos 1, 13V, hiband (index 6) > DVB-S IF freq is 1256000 >>>> tuning status == 0x00 >>>> tuning status == 0x00 >>>> tuning status == 0x00 >>>> tuning status == 0x00 >>>> tuning status == 0x00 >>>> tuning status == 0x00 >>>> tuning status == 0x00 >>>> tuning status == 0x00 >>>> tuning status == 0x00 >>>> tuning status == 0x00 > WARNING: >>> tuning failed!!! > ERROR: initial tuning failed > dumping lists (0 services) > Done. I can confirm this issue with jusst.de/hg/v4l-dvb. Take a look another thread. Ok. I'm not alone ;) Regards Oleg Roitburd _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [linux-dvb] S2API & TT3200 2008-10-28 11:53 ` oleg roitburd @ 2008-10-28 11:57 ` Jaap Crezee 2008-10-28 13:15 ` jean-paul 1 sibling, 0 replies; 11+ messages in thread From: Jaap Crezee @ 2008-10-28 11:57 UTC (permalink / raw) To: linux-dvb oleg roitburd wrote: > 2008/10/28 <jean-paul@goedee.nl>: > I can confirm this issue with jusst.de/hg/v4l-dvb. Take a look another thread. > Ok. I'm not alone ;) And I can confirm the following 2 repositories are not working for now: http://linuxtv.org/hg/v4l-dvb/ http://jusst.de/hg/v4l-dvb/ [both tune problems, almost no transponders lock] The following repository is working: http://mercurial.intuxication.org/hg/s2-liplianin [almost all transponders lock] Jaap Crezee _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [linux-dvb] S2API & TT3200 2008-10-28 11:53 ` oleg roitburd 2008-10-28 11:57 ` Jaap Crezee @ 2008-10-28 13:15 ` jean-paul 2008-10-28 20:06 ` Alex Betis 1 sibling, 1 reply; 11+ messages in thread From: jean-paul @ 2008-10-28 13:15 UTC (permalink / raw) Cc: linux-dvb If I install from http://mercurial.intuxication.org/hg/s2-liplianin/ I get some compile problems but it can overwrite by empty the problem cx88*.* files. Compile with jusst.de/hg/v4l-dvb without errors. Stage two: Try to scan some channels from the first lnb (19.2E) With v4l-dvb drivers I get some strange errors. With the S2 drivers I get (see below) API major 5, minor 0 scanning Astra-19.2E using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 12551500 V 22000000 22000000 ----------------------------------> Using DVB-S >>> tune to: 12551:vS0C56:S19.2E:22000: DiSEqC: uncommitted switch pos 0 DiSEqC: switch pos 0, 13V, hiband (index 2) DVB-S IF freq is 1951500 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 WARNING: >>> tuning failed!!! >>> tune to: 12551:vS0C56:S19.2E:22000: (tuning failed) DiSEqC: uncommitted switch pos 0 DiSEqC: switch pos 0, 13V, hiband (index 2) DVB-S IF freq is 1951500 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 >>> tuning status == 0x00 WARNING: >>> tuning failed!!! ----------------------------------> Using DVB-S2 >>> tune to: 12551:vS1C56:S19.2E:22000: (tuning failed) DiSEqC: uncommitted switch pos 0 DiSEqC: switch pos 0, 13V, hiband (index 2) DVB-S IF freq is 1951500 >>> tuning status == 0x1f >>> parse_section, section number 0 out of 0...! parse_pat...... PAT service_id = 0x0 service_id = 0xc pmt_pid = 0x2a service_id = 0xf98 pmt_pid = 0x34 service_id = 0xf9a pmt_pid = 0x26 service_id = 0xf9d pmt_pid = 0x31 service_id = 0x2f44 pmt_pid = 0x27 service_id = 0x2f58 pmt_pid = 0x23 service_id = 0x2f59 pmt_pid = 0x800 service_id = 0x2f5a pmt_pid = 0x20 service_id = 0x2f5b pmt_pid = 0x2f service_id = 0x2f5d pmt_pid = 0x1392 service_id = 0x2f80 pmt_pid = 0x30 service_id = 0x2f94 pmt_pid = 0x24 service_id = 0x2fa4 pmt_pid = 0x33 >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x0024 for service 0x2f94 VIDEO:PID 0x0037 AUDIO:PID 0x0038 >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x1392 for service 0x2f5d VIDEO:PID 0x1393 AUDIO:PID 0x1395 >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x0020 for service 0x2f5a VIDEO:PID 0x0021 AUDIO:PID 0x0022 >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x0800 for service 0x2f59 VIDEO:PID 0x0802 AUDIO:PID 0x0803 >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x0023 for service 0x2f58 VIDEO:PID 0x03ad AUDIO:PID 0x03af >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x0027 for service 0x2f44 VIDEO:PID 0x00a5 AUDIO:PID 0x00a6 >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x0026 for service 0x0f9a AUDIO:PID 0x0090 AUDIO:PID 0x0092 VIDEO:PID 0x00a8 >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x0033 for service 0x2fa4 >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x0030 for service 0x2f80 AUDIO:PID 0x0063 VIDEO:PID 0x00a2 >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x002f for service 0x2f5b VIDEO:PID 0x01cc AUDIO:PID 0x01d6 >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x0031 for service 0x0f9d AUDIO:PID 0x0090 AUDIO:PID 0x0092 VIDEO:PID 0x00a8 >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x0034 for service 0x0f98 VIDEO:PID 0x0062 AUDIO:PID 0x1163 AUDIO:PID 0x1165 AUDIO:PID 0x116b >>> parse_section, section number 0 out of 0...! parse_pmt...... PMT 0x002a for service 0x000c WARNING: filter timeout pid 0x1ffb dumping lists (13 services) Done. gives the output: (null) - [0f98]:12551:vS1C56:S19.2E:22000:98:4451=deu,4453=fra,4459=spa:0:0:3992:0:0:0 (null) - [0f9a]:12551:vS1C56:S19.2E:22000:168:144=ltz,146=fre:301:0:3994:0:0:0 (null) - [0f9d]:12551:vS1C56:S19.2E:22000:168:144=ltz,146=fre:74:0:3997:0:0:0 (null) - [2f44]:12551:vS1C56:S19.2E:22000:165:166:167:0:12100:0:0:0 (null) - [2f58]:12551:vS1C56:S19.2E:22000:941:943=fre:0:0:12120:0:0:0 (null) - [2f59]:12551:vS1C56:S19.2E:22000:2050:2051=fre:0:0:12121:0:0:0 (null) - [2f5a]:12551:vS1C56:S19.2E:22000:33:34=deu:0:0:12122:0:0:0 (null) - [2f5b]:12551:vS1C56:S19.2E:22000:460+511:470:0:0:12123:0:0:0 (null) - [2f5d]:12551:vS1C56:S19.2E:22000:5011:5013=ger:0:0:12125:0:0:0 (null) - [2f80]:12551:vS1C56:S19.2E:22000:162:99=ger:0:0:12160:0:0:0 (null) - [2f94]:12551:vS1C56:S19.2E:22000:55:56=ltz:0:0:12180:0:0:0 The second one (-s 1) gives noting. For so far. I?m not able to watch any channel. Jean-Paul _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [linux-dvb] S2API & TT3200 2008-10-28 13:15 ` jean-paul @ 2008-10-28 20:06 ` Alex Betis 2008-10-29 9:59 ` jean-paul 0 siblings, 1 reply; 11+ messages in thread From: Alex Betis @ 2008-10-28 20:06 UTC (permalink / raw) To: jean-paul; +Cc: linux-dvb [-- Attachment #1.1: Type: text/plain, Size: 5904 bytes --] Hi, Are you using the frequency files the come with the scan-s2? I wrote in README that those are sample files and you'll have to change them. Try to change the frequency to 12552000 and scan again. According to lyngsat it's suppose to be DVB-S channel. I don't have a dish to Astra 19.2 so I can't test it myself. Regarding the other LNB that doesn't work for you, maybe that's the same problem that you don't have correct frequencies in the file? On Tue, Oct 28, 2008 at 3:15 PM, <jean-paul@goedee.nl> wrote: > If I install from http://mercurial.intuxication.org/hg/s2-liplianin/ I > get some compile problems but it can overwrite by empty the problem > cx88*.* files. Compile with jusst.de/hg/v4l-dvb without errors. > > Stage two: Try to scan some channels from the first lnb (19.2E) > > With v4l-dvb drivers I get some strange errors. With the S2 drivers I > get (see below) > > > API major 5, minor 0 > scanning Astra-19.2E > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > initial transponder 12551500 V 22000000 22000000 > ----------------------------------> Using DVB-S > >>> tune to: 12551:vS0C56:S19.2E:22000: > DiSEqC: uncommitted switch pos 0 > DiSEqC: switch pos 0, 13V, hiband (index 2) > DVB-S IF freq is 1951500 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > WARNING: >>> tuning failed!!! > >>> tune to: 12551:vS0C56:S19.2E:22000: (tuning failed) > DiSEqC: uncommitted switch pos 0 > DiSEqC: switch pos 0, 13V, hiband (index 2) > DVB-S IF freq is 1951500 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > >>> tuning status == 0x00 > WARNING: >>> tuning failed!!! > ----------------------------------> Using DVB-S2 > >>> tune to: 12551:vS1C56:S19.2E:22000: (tuning failed) > DiSEqC: uncommitted switch pos 0 > DiSEqC: switch pos 0, 13V, hiband (index 2) > DVB-S IF freq is 1951500 > >>> tuning status == 0x1f > >>> parse_section, section number 0 out of 0...! > parse_pat...... > PAT > service_id = 0x0 > service_id = 0xc > pmt_pid = 0x2a > service_id = 0xf98 > pmt_pid = 0x34 > service_id = 0xf9a > pmt_pid = 0x26 > service_id = 0xf9d > pmt_pid = 0x31 > service_id = 0x2f44 > pmt_pid = 0x27 > service_id = 0x2f58 > pmt_pid = 0x23 > service_id = 0x2f59 > pmt_pid = 0x800 > service_id = 0x2f5a > pmt_pid = 0x20 > service_id = 0x2f5b > pmt_pid = 0x2f > service_id = 0x2f5d > pmt_pid = 0x1392 > service_id = 0x2f80 > pmt_pid = 0x30 > service_id = 0x2f94 > pmt_pid = 0x24 > service_id = 0x2fa4 > pmt_pid = 0x33 > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x0024 for service 0x2f94 > VIDEO:PID 0x0037 > AUDIO:PID 0x0038 > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x1392 for service 0x2f5d > VIDEO:PID 0x1393 > AUDIO:PID 0x1395 > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x0020 for service 0x2f5a > VIDEO:PID 0x0021 > AUDIO:PID 0x0022 > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x0800 for service 0x2f59 > VIDEO:PID 0x0802 > AUDIO:PID 0x0803 > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x0023 for service 0x2f58 > VIDEO:PID 0x03ad > AUDIO:PID 0x03af > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x0027 for service 0x2f44 > VIDEO:PID 0x00a5 > AUDIO:PID 0x00a6 > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x0026 for service 0x0f9a > AUDIO:PID 0x0090 > AUDIO:PID 0x0092 > VIDEO:PID 0x00a8 > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x0033 for service 0x2fa4 > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x0030 for service 0x2f80 > AUDIO:PID 0x0063 > VIDEO:PID 0x00a2 > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x002f for service 0x2f5b > VIDEO:PID 0x01cc > AUDIO:PID 0x01d6 > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x0031 for service 0x0f9d > AUDIO:PID 0x0090 > AUDIO:PID 0x0092 > VIDEO:PID 0x00a8 > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x0034 for service 0x0f98 > VIDEO:PID 0x0062 > AUDIO:PID 0x1163 > AUDIO:PID 0x1165 > AUDIO:PID 0x116b > >>> parse_section, section number 0 out of 0...! > parse_pmt...... > PMT 0x002a for service 0x000c > WARNING: filter timeout pid 0x1ffb > dumping lists (13 services) > Done. > > > gives the output: > > (null) - > > [0f98]:12551:vS1C56:S19.2E:22000:98:4451=deu,4453=fra,4459=spa:0:0:3992:0:0:0 > (null) - > [0f9a]:12551:vS1C56:S19.2E:22000:168:144=ltz,146=fre:301:0:3994:0:0:0 > (null) - > [0f9d]:12551:vS1C56:S19.2E:22000:168:144=ltz,146=fre:74:0:3997:0:0:0 > (null) - [2f44]:12551:vS1C56:S19.2E:22000:165:166:167:0:12100:0:0:0 > (null) - [2f58]:12551:vS1C56:S19.2E:22000:941:943=fre:0:0:12120:0:0:0 > (null) - [2f59]:12551:vS1C56:S19.2E:22000:2050:2051=fre:0:0:12121:0:0:0 > (null) - [2f5a]:12551:vS1C56:S19.2E:22000:33:34=deu:0:0:12122:0:0:0 > (null) - [2f5b]:12551:vS1C56:S19.2E:22000:460+511:470:0:0:12123:0:0:0 > (null) - [2f5d]:12551:vS1C56:S19.2E:22000:5011:5013=ger:0:0:12125:0:0:0 > (null) - [2f80]:12551:vS1C56:S19.2E:22000:162:99=ger:0:0:12160:0:0:0 > (null) - [2f94]:12551:vS1C56:S19.2E:22000:55:56=ltz:0:0:12180:0:0:0 > > The second one (-s 1) gives noting. > > > For so far. I?m not able to watch any channel. > > > Jean-Paul > > > > _______________________________________________ > linux-dvb mailing list > linux-dvb@linuxtv.org > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > [-- Attachment #1.2: Type: text/html, Size: 7432 bytes --] [-- Attachment #2: Type: text/plain, Size: 150 bytes --] _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [linux-dvb] S2API & TT3200 2008-10-28 20:06 ` Alex Betis @ 2008-10-29 9:59 ` jean-paul 2008-10-29 19:06 ` Alex Betis 0 siblings, 1 reply; 11+ messages in thread From: jean-paul @ 2008-10-29 9:59 UTC (permalink / raw) To: Alex Betis; +Cc: linux-dvb Ok its possible to scan booth lnbs but only S channels not S2. Another problem is the ?x parameter not working. Most of the channels are encrypted and using this ?x for fill up the channels info with 999. Vdr is fill it with the correct numbers regards Jean-paul Citeren Alex Betis <alex.betis@gmail.com>: > Hi, > > Are you using the frequency files the come with the scan-s2? I wrote in > README that those are sample files and you'll have to change them. Try to > change the frequency to 12552000 and scan again. According to lyngsat it's > suppose to be DVB-S channel. > I don't have a dish to Astra 19.2 so I can't test it myself. > > Regarding the other LNB that doesn't work for you, maybe that's the same > problem that you don't have correct frequencies in the file? > > > On Tue, Oct 28, 2008 at 3:15 PM, <jean-paul@goedee.nl> wrote: > >> If I install from http://mercurial.intuxication.org/hg/s2-liplianin/ I >> get some compile problems but it can overwrite by empty the problem >> cx88*.* files. Compile with jusst.de/hg/v4l-dvb without errors. >> >> Stage two: Try to scan some channels from the first lnb (19.2E) >> >> With v4l-dvb drivers I get some strange errors. With the S2 drivers I >> get (see below) >> >> >> API major 5, minor 0 >> scanning Astra-19.2E >> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' >> initial transponder 12551500 V 22000000 22000000 >> ----------------------------------> Using DVB-S >> >>> tune to: 12551:vS0C56:S19.2E:22000: >> DiSEqC: uncommitted switch pos 0 >> DiSEqC: switch pos 0, 13V, hiband (index 2) >> DVB-S IF freq is 1951500 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> WARNING: >>> tuning failed!!! >> >>> tune to: 12551:vS0C56:S19.2E:22000: (tuning failed) >> DiSEqC: uncommitted switch pos 0 >> DiSEqC: switch pos 0, 13V, hiband (index 2) >> DVB-S IF freq is 1951500 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> >>> tuning status == 0x00 >> WARNING: >>> tuning failed!!! >> ----------------------------------> Using DVB-S2 >> >>> tune to: 12551:vS1C56:S19.2E:22000: (tuning failed) >> DiSEqC: uncommitted switch pos 0 >> DiSEqC: switch pos 0, 13V, hiband (index 2) >> DVB-S IF freq is 1951500 >> >>> tuning status == 0x1f >> >>> parse_section, section number 0 out of 0...! >> parse_pat...... >> PAT >> service_id = 0x0 >> service_id = 0xc >> pmt_pid = 0x2a >> service_id = 0xf98 >> pmt_pid = 0x34 >> service_id = 0xf9a >> pmt_pid = 0x26 >> service_id = 0xf9d >> pmt_pid = 0x31 >> service_id = 0x2f44 >> pmt_pid = 0x27 >> service_id = 0x2f58 >> pmt_pid = 0x23 >> service_id = 0x2f59 >> pmt_pid = 0x800 >> service_id = 0x2f5a >> pmt_pid = 0x20 >> service_id = 0x2f5b >> pmt_pid = 0x2f >> service_id = 0x2f5d >> pmt_pid = 0x1392 >> service_id = 0x2f80 >> pmt_pid = 0x30 >> service_id = 0x2f94 >> pmt_pid = 0x24 >> service_id = 0x2fa4 >> pmt_pid = 0x33 >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x0024 for service 0x2f94 >> VIDEO:PID 0x0037 >> AUDIO:PID 0x0038 >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x1392 for service 0x2f5d >> VIDEO:PID 0x1393 >> AUDIO:PID 0x1395 >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x0020 for service 0x2f5a >> VIDEO:PID 0x0021 >> AUDIO:PID 0x0022 >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x0800 for service 0x2f59 >> VIDEO:PID 0x0802 >> AUDIO:PID 0x0803 >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x0023 for service 0x2f58 >> VIDEO:PID 0x03ad >> AUDIO:PID 0x03af >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x0027 for service 0x2f44 >> VIDEO:PID 0x00a5 >> AUDIO:PID 0x00a6 >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x0026 for service 0x0f9a >> AUDIO:PID 0x0090 >> AUDIO:PID 0x0092 >> VIDEO:PID 0x00a8 >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x0033 for service 0x2fa4 >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x0030 for service 0x2f80 >> AUDIO:PID 0x0063 >> VIDEO:PID 0x00a2 >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x002f for service 0x2f5b >> VIDEO:PID 0x01cc >> AUDIO:PID 0x01d6 >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x0031 for service 0x0f9d >> AUDIO:PID 0x0090 >> AUDIO:PID 0x0092 >> VIDEO:PID 0x00a8 >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x0034 for service 0x0f98 >> VIDEO:PID 0x0062 >> AUDIO:PID 0x1163 >> AUDIO:PID 0x1165 >> AUDIO:PID 0x116b >> >>> parse_section, section number 0 out of 0...! >> parse_pmt...... >> PMT 0x002a for service 0x000c >> WARNING: filter timeout pid 0x1ffb >> dumping lists (13 services) >> Done. >> >> >> gives the output: >> >> (null) - >> >> [0f98]:12551:vS1C56:S19.2E:22000:98:4451=deu,4453=fra,4459=spa:0:0:3992:0:0:0 >> (null) - >> [0f9a]:12551:vS1C56:S19.2E:22000:168:144=ltz,146=fre:301:0:3994:0:0:0 >> (null) - >> [0f9d]:12551:vS1C56:S19.2E:22000:168:144=ltz,146=fre:74:0:3997:0:0:0 >> (null) - [2f44]:12551:vS1C56:S19.2E:22000:165:166:167:0:12100:0:0:0 >> (null) - [2f58]:12551:vS1C56:S19.2E:22000:941:943=fre:0:0:12120:0:0:0 >> (null) - [2f59]:12551:vS1C56:S19.2E:22000:2050:2051=fre:0:0:12121:0:0:0 >> (null) - [2f5a]:12551:vS1C56:S19.2E:22000:33:34=deu:0:0:12122:0:0:0 >> (null) - [2f5b]:12551:vS1C56:S19.2E:22000:460+511:470:0:0:12123:0:0:0 >> (null) - [2f5d]:12551:vS1C56:S19.2E:22000:5011:5013=ger:0:0:12125:0:0:0 >> (null) - [2f80]:12551:vS1C56:S19.2E:22000:162:99=ger:0:0:12160:0:0:0 >> (null) - [2f94]:12551:vS1C56:S19.2E:22000:55:56=ltz:0:0:12180:0:0:0 >> >> The second one (-s 1) gives noting. >> >> >> For so far. I?m not able to watch any channel. >> >> >> Jean-Paul >> >> >> >> _______________________________________________ >> linux-dvb mailing list >> linux-dvb@linuxtv.org >> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >> > _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [linux-dvb] S2API & TT3200 2008-10-29 9:59 ` jean-paul @ 2008-10-29 19:06 ` Alex Betis 2008-10-30 6:59 ` jean-paul 0 siblings, 1 reply; 11+ messages in thread From: Alex Betis @ 2008-10-29 19:06 UTC (permalink / raw) To: jean-paul; +Cc: linux-dvb [-- Attachment #1.1: Type: text/plain, Size: 6945 bytes --] Take the new version where -x parameter was fixed. You probably want to use value "-1" for that parameter where all channels will have 0 value in CAID or "-2" where all the channels will be filled with real CAID value. On Wed, Oct 29, 2008 at 11:59 AM, <jean-paul@goedee.nl> wrote: > Ok its possible to scan booth lnbs but only S channels not S2. Another > problem is the ?x parameter not working. Most of the channels are encrypted > and using this ?x for fill up the channels info with 999. Vdr is fill it > with the correct numbers > > regards > > Jean-paul > > > > Citeren Alex Betis <alex.betis@gmail.com>: > > > Hi, >> >> Are you using the frequency files the come with the scan-s2? I wrote in >> README that those are sample files and you'll have to change them. Try to >> change the frequency to 12552000 and scan again. According to lyngsat it's >> suppose to be DVB-S channel. >> I don't have a dish to Astra 19.2 so I can't test it myself. >> >> Regarding the other LNB that doesn't work for you, maybe that's the same >> problem that you don't have correct frequencies in the file? >> >> >> On Tue, Oct 28, 2008 at 3:15 PM, <jean-paul@goedee.nl> wrote: >> >> If I install from http://mercurial.intuxication.org/hg/s2-liplianin/ I >>> get some compile problems but it can overwrite by empty the problem >>> cx88*.* files. Compile with jusst.de/hg/v4l-dvb without errors. >>> >>> Stage two: Try to scan some channels from the first lnb (19.2E) >>> >>> With v4l-dvb drivers I get some strange errors. With the S2 drivers I >>> get (see below) >>> >>> >>> API major 5, minor 0 >>> scanning Astra-19.2E >>> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' >>> initial transponder 12551500 V 22000000 22000000 >>> ----------------------------------> Using DVB-S >>> >>> tune to: 12551:vS0C56:S19.2E:22000: >>> DiSEqC: uncommitted switch pos 0 >>> DiSEqC: switch pos 0, 13V, hiband (index 2) >>> DVB-S IF freq is 1951500 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> WARNING: >>> tuning failed!!! >>> >>> tune to: 12551:vS0C56:S19.2E:22000: (tuning failed) >>> DiSEqC: uncommitted switch pos 0 >>> DiSEqC: switch pos 0, 13V, hiband (index 2) >>> DVB-S IF freq is 1951500 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> >>> tuning status == 0x00 >>> WARNING: >>> tuning failed!!! >>> ----------------------------------> Using DVB-S2 >>> >>> tune to: 12551:vS1C56:S19.2E:22000: (tuning failed) >>> DiSEqC: uncommitted switch pos 0 >>> DiSEqC: switch pos 0, 13V, hiband (index 2) >>> DVB-S IF freq is 1951500 >>> >>> tuning status == 0x1f >>> >>> parse_section, section number 0 out of 0...! >>> parse_pat...... >>> PAT >>> service_id = 0x0 >>> service_id = 0xc >>> pmt_pid = 0x2a >>> service_id = 0xf98 >>> pmt_pid = 0x34 >>> service_id = 0xf9a >>> pmt_pid = 0x26 >>> service_id = 0xf9d >>> pmt_pid = 0x31 >>> service_id = 0x2f44 >>> pmt_pid = 0x27 >>> service_id = 0x2f58 >>> pmt_pid = 0x23 >>> service_id = 0x2f59 >>> pmt_pid = 0x800 >>> service_id = 0x2f5a >>> pmt_pid = 0x20 >>> service_id = 0x2f5b >>> pmt_pid = 0x2f >>> service_id = 0x2f5d >>> pmt_pid = 0x1392 >>> service_id = 0x2f80 >>> pmt_pid = 0x30 >>> service_id = 0x2f94 >>> pmt_pid = 0x24 >>> service_id = 0x2fa4 >>> pmt_pid = 0x33 >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x0024 for service 0x2f94 >>> VIDEO:PID 0x0037 >>> AUDIO:PID 0x0038 >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x1392 for service 0x2f5d >>> VIDEO:PID 0x1393 >>> AUDIO:PID 0x1395 >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x0020 for service 0x2f5a >>> VIDEO:PID 0x0021 >>> AUDIO:PID 0x0022 >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x0800 for service 0x2f59 >>> VIDEO:PID 0x0802 >>> AUDIO:PID 0x0803 >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x0023 for service 0x2f58 >>> VIDEO:PID 0x03ad >>> AUDIO:PID 0x03af >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x0027 for service 0x2f44 >>> VIDEO:PID 0x00a5 >>> AUDIO:PID 0x00a6 >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x0026 for service 0x0f9a >>> AUDIO:PID 0x0090 >>> AUDIO:PID 0x0092 >>> VIDEO:PID 0x00a8 >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x0033 for service 0x2fa4 >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x0030 for service 0x2f80 >>> AUDIO:PID 0x0063 >>> VIDEO:PID 0x00a2 >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x002f for service 0x2f5b >>> VIDEO:PID 0x01cc >>> AUDIO:PID 0x01d6 >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x0031 for service 0x0f9d >>> AUDIO:PID 0x0090 >>> AUDIO:PID 0x0092 >>> VIDEO:PID 0x00a8 >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x0034 for service 0x0f98 >>> VIDEO:PID 0x0062 >>> AUDIO:PID 0x1163 >>> AUDIO:PID 0x1165 >>> AUDIO:PID 0x116b >>> >>> parse_section, section number 0 out of 0...! >>> parse_pmt...... >>> PMT 0x002a for service 0x000c >>> WARNING: filter timeout pid 0x1ffb >>> dumping lists (13 services) >>> Done. >>> >>> >>> gives the output: >>> >>> (null) - >>> >>> >>> [0f98]:12551:vS1C56:S19.2E:22000:98:4451=deu,4453=fra,4459=spa:0:0:3992:0:0:0 >>> (null) - >>> [0f9a]:12551:vS1C56:S19.2E:22000:168:144=ltz,146=fre:301:0:3994:0:0:0 >>> (null) - >>> [0f9d]:12551:vS1C56:S19.2E:22000:168:144=ltz,146=fre:74:0:3997:0:0:0 >>> (null) - [2f44]:12551:vS1C56:S19.2E:22000:165:166:167:0:12100:0:0:0 >>> (null) - [2f58]:12551:vS1C56:S19.2E:22000:941:943=fre:0:0:12120:0:0:0 >>> (null) - [2f59]:12551:vS1C56:S19.2E:22000:2050:2051=fre:0:0:12121:0:0:0 >>> (null) - [2f5a]:12551:vS1C56:S19.2E:22000:33:34=deu:0:0:12122:0:0:0 >>> (null) - [2f5b]:12551:vS1C56:S19.2E:22000:460+511:470:0:0:12123:0:0:0 >>> (null) - [2f5d]:12551:vS1C56:S19.2E:22000:5011:5013=ger:0:0:12125:0:0:0 >>> (null) - [2f80]:12551:vS1C56:S19.2E:22000:162:99=ger:0:0:12160:0:0:0 >>> (null) - [2f94]:12551:vS1C56:S19.2E:22000:55:56=ltz:0:0:12180:0:0:0 >>> >>> The second one (-s 1) gives noting. >>> >>> >>> For so far. I?m not able to watch any channel. >>> >>> >>> Jean-Paul >>> >>> >>> >>> _______________________________________________ >>> linux-dvb mailing list >>> linux-dvb@linuxtv.org >>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >>> >>> >> > > > [-- Attachment #1.2: Type: text/html, Size: 8475 bytes --] [-- Attachment #2: Type: text/plain, Size: 150 bytes --] _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [linux-dvb] S2API & TT3200 2008-10-29 19:06 ` Alex Betis @ 2008-10-30 6:59 ` jean-paul 0 siblings, 0 replies; 11+ messages in thread From: jean-paul @ 2008-10-30 6:59 UTC (permalink / raw) To: Alex Betis; +Cc: linux-dvb Yes ?x (CI/CA) is working now with the last version. Thanx. Citeren Alex Betis <alex.betis@gmail.com>: > Take the new version where -x parameter was fixed. > You probably want to use value "-1" for that parameter where all channels > will have 0 value in CAID > or "-2" where all the channels will be filled with real CAID value. > > > On Wed, Oct 29, 2008 at 11:59 AM, <jean-paul@goedee.nl> wrote: > >> Ok its possible to scan booth lnbs but only S channels not S2. Another >> problem is the ?x parameter not working. Most of the channels are encrypted >> and using this ?x for fill up the channels info with 999. Vdr is fill it >> with the correct numbers >> >> regards >> >> Jean-paul >> >> >> >> Citeren Alex Betis <alex.betis@gmail.com>: >> >> >> Hi, >>> >>> Are you using the frequency files the come with the scan-s2? I wrote in >>> README that those are sample files and you'll have to change them. Try to >>> change the frequency to 12552000 and scan again. According to lyngsat it's >>> suppose to be DVB-S channel. >>> I don't have a dish to Astra 19.2 so I can't test it myself. >>> >>> Regarding the other LNB that doesn't work for you, maybe that's the same >>> problem that you don't have correct frequencies in the file? >>> >>> >>> On Tue, Oct 28, 2008 at 3:15 PM, <jean-paul@goedee.nl> wrote: >>> >>> If I install from http://mercurial.intuxication.org/hg/s2-liplianin/ I >>>> get some compile problems but it can overwrite by empty the problem >>>> cx88*.* files. Compile with jusst.de/hg/v4l-dvb without errors. >>>> >>>> Stage two: Try to scan some channels from the first lnb (19.2E) >>>> >>>> With v4l-dvb drivers I get some strange errors. With the S2 drivers I >>>> get (see below) >>>> >>>> >>>> API major 5, minor 0 >>>> scanning Astra-19.2E >>>> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' >>>> initial transponder 12551500 V 22000000 22000000 >>>> ----------------------------------> Using DVB-S >>>> >>> tune to: 12551:vS0C56:S19.2E:22000: >>>> DiSEqC: uncommitted switch pos 0 >>>> DiSEqC: switch pos 0, 13V, hiband (index 2) >>>> DVB-S IF freq is 1951500 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> WARNING: >>> tuning failed!!! >>>> >>> tune to: 12551:vS0C56:S19.2E:22000: (tuning failed) >>>> DiSEqC: uncommitted switch pos 0 >>>> DiSEqC: switch pos 0, 13V, hiband (index 2) >>>> DVB-S IF freq is 1951500 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> >>> tuning status == 0x00 >>>> WARNING: >>> tuning failed!!! >>>> ----------------------------------> Using DVB-S2 >>>> >>> tune to: 12551:vS1C56:S19.2E:22000: (tuning failed) >>>> DiSEqC: uncommitted switch pos 0 >>>> DiSEqC: switch pos 0, 13V, hiband (index 2) >>>> DVB-S IF freq is 1951500 >>>> >>> tuning status == 0x1f >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pat...... >>>> PAT >>>> service_id = 0x0 >>>> service_id = 0xc >>>> pmt_pid = 0x2a >>>> service_id = 0xf98 >>>> pmt_pid = 0x34 >>>> service_id = 0xf9a >>>> pmt_pid = 0x26 >>>> service_id = 0xf9d >>>> pmt_pid = 0x31 >>>> service_id = 0x2f44 >>>> pmt_pid = 0x27 >>>> service_id = 0x2f58 >>>> pmt_pid = 0x23 >>>> service_id = 0x2f59 >>>> pmt_pid = 0x800 >>>> service_id = 0x2f5a >>>> pmt_pid = 0x20 >>>> service_id = 0x2f5b >>>> pmt_pid = 0x2f >>>> service_id = 0x2f5d >>>> pmt_pid = 0x1392 >>>> service_id = 0x2f80 >>>> pmt_pid = 0x30 >>>> service_id = 0x2f94 >>>> pmt_pid = 0x24 >>>> service_id = 0x2fa4 >>>> pmt_pid = 0x33 >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x0024 for service 0x2f94 >>>> VIDEO:PID 0x0037 >>>> AUDIO:PID 0x0038 >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x1392 for service 0x2f5d >>>> VIDEO:PID 0x1393 >>>> AUDIO:PID 0x1395 >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x0020 for service 0x2f5a >>>> VIDEO:PID 0x0021 >>>> AUDIO:PID 0x0022 >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x0800 for service 0x2f59 >>>> VIDEO:PID 0x0802 >>>> AUDIO:PID 0x0803 >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x0023 for service 0x2f58 >>>> VIDEO:PID 0x03ad >>>> AUDIO:PID 0x03af >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x0027 for service 0x2f44 >>>> VIDEO:PID 0x00a5 >>>> AUDIO:PID 0x00a6 >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x0026 for service 0x0f9a >>>> AUDIO:PID 0x0090 >>>> AUDIO:PID 0x0092 >>>> VIDEO:PID 0x00a8 >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x0033 for service 0x2fa4 >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x0030 for service 0x2f80 >>>> AUDIO:PID 0x0063 >>>> VIDEO:PID 0x00a2 >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x002f for service 0x2f5b >>>> VIDEO:PID 0x01cc >>>> AUDIO:PID 0x01d6 >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x0031 for service 0x0f9d >>>> AUDIO:PID 0x0090 >>>> AUDIO:PID 0x0092 >>>> VIDEO:PID 0x00a8 >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x0034 for service 0x0f98 >>>> VIDEO:PID 0x0062 >>>> AUDIO:PID 0x1163 >>>> AUDIO:PID 0x1165 >>>> AUDIO:PID 0x116b >>>> >>> parse_section, section number 0 out of 0...! >>>> parse_pmt...... >>>> PMT 0x002a for service 0x000c >>>> WARNING: filter timeout pid 0x1ffb >>>> dumping lists (13 services) >>>> Done. >>>> >>>> >>>> gives the output: >>>> >>>> (null) - >>>> >>>> >>>> [0f98]:12551:vS1C56:S19.2E:22000:98:4451=deu,4453=fra,4459=spa:0:0:3992:0:0:0 >>>> (null) - >>>> [0f9a]:12551:vS1C56:S19.2E:22000:168:144=ltz,146=fre:301:0:3994:0:0:0 >>>> (null) - >>>> [0f9d]:12551:vS1C56:S19.2E:22000:168:144=ltz,146=fre:74:0:3997:0:0:0 >>>> (null) - [2f44]:12551:vS1C56:S19.2E:22000:165:166:167:0:12100:0:0:0 >>>> (null) - [2f58]:12551:vS1C56:S19.2E:22000:941:943=fre:0:0:12120:0:0:0 >>>> (null) - [2f59]:12551:vS1C56:S19.2E:22000:2050:2051=fre:0:0:12121:0:0:0 >>>> (null) - [2f5a]:12551:vS1C56:S19.2E:22000:33:34=deu:0:0:12122:0:0:0 >>>> (null) - [2f5b]:12551:vS1C56:S19.2E:22000:460+511:470:0:0:12123:0:0:0 >>>> (null) - [2f5d]:12551:vS1C56:S19.2E:22000:5011:5013=ger:0:0:12125:0:0:0 >>>> (null) - [2f80]:12551:vS1C56:S19.2E:22000:162:99=ger:0:0:12160:0:0:0 >>>> (null) - [2f94]:12551:vS1C56:S19.2E:22000:55:56=ltz:0:0:12180:0:0:0 >>>> >>>> The second one (-s 1) gives noting. >>>> >>>> >>>> For so far. I?m not able to watch any channel. >>>> >>>> >>>> Jean-Paul >>>> >>>> >>>> >>>> _______________________________________________ >>>> linux-dvb mailing list >>>> linux-dvb@linuxtv.org >>>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >>>> >>>> >>> >> >> >> > _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb ^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2008-10-30 6:59 UTC | newest] Thread overview: 11+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2008-10-28 10:15 [linux-dvb] S2API & TT3200 jean-paul 2008-10-28 10:24 ` oleg roitburd 2008-10-28 10:30 ` Manu Abraham 2008-10-28 11:45 ` jean-paul 2008-10-28 11:53 ` oleg roitburd 2008-10-28 11:57 ` Jaap Crezee 2008-10-28 13:15 ` jean-paul 2008-10-28 20:06 ` Alex Betis 2008-10-29 9:59 ` jean-paul 2008-10-29 19:06 ` Alex Betis 2008-10-30 6:59 ` jean-paul
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox