Re: kernel soft lockup on boot loading cx2388x based DVB-S card (TeVii S420)

Re: kernel soft lockup on boot loading cx2388x based DVB-S card (TeVii S420)

[Aaron Theodore]

I tried:
make rmmod
make rminstall

Although there were still some drivers left over from "tevii_linuxdriver_0815"

/lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/dvb-usb/dvb-usb-s600.ko
/lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/dvb-usb/dvb-usb-s650.ko
/lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/zr36067.ko
/lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/zr36060.ko
/lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/zr36050.ko
/lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/saa7134/saa7134-oss.ko
/lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/zr36016.ko
/lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/tuner-3036.ko
/lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/videocodec.ko
/lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/dpc7146.ko

so i just removed manually and rebooted.
Same issue occurred on reboot.

So i thought to try manually unloading and reloading the module


barry:~# rmmod cx8802
barry:~# modprobe cx8802   

kernel: cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
kernel: cx88[0]/2: cx2388x 8802 Driver Manager
kernel: ACPI: PCI Interrupt 0000:05:08.2[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
kernel: cx88[0]/2: found at 0000:05:08.2, rev: 5, irq: 18, latency: 32, mmio: 0xd9000000
kernel: cx88/2: cx2388x dvb driver version 0.0.6 loaded
kernel: cx88/2: registering cx8802 driver, type: dvb access: shared
kernel: cx88[0]/2: subsystem: d420:9022, board: TeVii S420 DVB-S [card=73]
kernel: cx88[0]/2: cx2388x based DVB/ATSC card
kernel: cx8802_alloc_frontends() allocating 1 frontend(s)
kernel: DVB: registering new adapter (cx88[0])
kernel: DVB: registering adapter 2 frontend 0 (ST STV0288 DVB-S)...


This time it makes the devices in /dev/dvb/
Now unfortunately i can't test to see if it can actually Tune until a few hours time when i get home (i think i forgot to plug my satellite cable back in!)

Will report back later


Can i change the load order of kernel modules, it dosnt seem to like being loaded before my other dvb modules


Aaron


----- "Mauro Carvalho Chehab" <mchehab@infradead.org> wrote:

> On Fri, 16 Jan 2009 06:56:05 +1100
> Aaron Theodore <aaron@bat.id.au> wrote:
> 
> > Mauro,
> > 
> > Thanks for the speedy patch!
> 
> You should thanks to Andy. He is the author of this patch ;)
> 
> > My system can at least boot now, but has issues loading the
> frontend.
> > DVB: Unable to find symbol stv0299_attach()
> > DVB: Unable to find symbol stv0288_attach()
> 
> It seems that you didn't compile those two frontends.
> 
> Cheers,
> Mauro

Re: kernel soft lockup on boot loading cx2388x based DVB-S card (TeVii S420)

[Aaron Theodore]

Horay my TeVii DVB-S S420 is now working,
only thing now is to work out why it wont load on boot before my DVB-T card

On 16/01/2009 3:19 PM, Aaron Theodore wrote:
> I tried:
> make rmmod
> make rminstall
>
> Although there were still some drivers left over from "tevii_linuxdriver_0815"
>
> /lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/dvb-usb/dvb-usb-s600.ko
> /lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/dvb-usb/dvb-usb-s650.ko
> /lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/zr36067.ko
> /lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/zr36060.ko
> /lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/zr36050.ko
> /lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/saa7134/saa7134-oss.ko
> /lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/zr36016.ko
> /lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/tuner-3036.ko
> /lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/videocodec.ko
> /lib/modules/2.6.24-etchnhalf.1-686/kernel/drivers/media/video/dpc7146.ko
>
> so i just removed manually and rebooted.
> Same issue occurred on reboot.
>
> So i thought to try manually unloading and reloading the module
>
>
> barry:~# rmmod cx8802
> barry:~# modprobe cx8802   
>
> kernel: cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
> kernel: cx88[0]/2: cx2388x 8802 Driver Manager
> kernel: ACPI: PCI Interrupt 0000:05:08.2[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
> kernel: cx88[0]/2: found at 0000:05:08.2, rev: 5, irq: 18, latency: 32, mmio: 0xd9000000
> kernel: cx88/2: cx2388x dvb driver version 0.0.6 loaded
> kernel: cx88/2: registering cx8802 driver, type: dvb access: shared
> kernel: cx88[0]/2: subsystem: d420:9022, board: TeVii S420 DVB-S [card=73]
> kernel: cx88[0]/2: cx2388x based DVB/ATSC card
> kernel: cx8802_alloc_frontends() allocating 1 frontend(s)
> kernel: DVB: registering new adapter (cx88[0])
> kernel: DVB: registering adapter 2 frontend 0 (ST STV0288 DVB-S)...
>
>
> This time it makes the devices in /dev/dvb/
> Now unfortunately i can't test to see if it can actually Tune until a few hours time when i get home (i think i forgot to plug my satellite cable back in!)
>
> Will report back later
>
>
> Can i change the load order of kernel modules, it dosnt seem to like being loaded before my other dvb modules
>
>
> Aaron
>
>
> ----- "Mauro Carvalho Chehab" <mchehab@infradead.org> wrote:
>
>   
>> On Fri, 16 Jan 2009 06:56:05 +1100
>> Aaron Theodore <aaron@bat.id.au> wrote:
>>
>>     
>>> Mauro,
>>>
>>> Thanks for the speedy patch!
>>>       
>> You should thanks to Andy. He is the author of this patch ;)
>>
>>     
>>> My system can at least boot now, but has issues loading the
>>>       
>> frontend.
>>     
>>> DVB: Unable to find symbol stv0299_attach()
>>> DVB: Unable to find symbol stv0288_attach()
>>>       
>> It seems that you didn't compile those two frontends.
>>
>> Cheers,
>> Mauro
>>     
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>   

kernel soft lockup on boot loading cx2388x based DVB-S card (TeVii S420)

[Aaron Theodore]

Hi I'm running Debian with kernel: 2.6.24-etchnhalf.1-686
I recently baught a TeVii S420 DVB-S card and have been tring to get it 
to work.

Firstly i built the v4l from: http://linuxtv.org/hg/v4l-dvb (hg clone) 
as the card was not detected.
On first reboot after new modules are installed i get a kernel soft 
lockup....

-------------------------------------------------
Linux video capture interface: v2.00
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:05:08.0[A] -> Link [APC3] -> GSI 18 (level, 
low) -> IRQ 21
cx88[0]: subsystem: d420:9022, board: TeVii S420 DVB-S 
[card=73,autodetected], frontend(s): 1
cx88[0]: TV tuner type -1, Radio tuner type -1
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
tuner' 2-0068: chip found @ 0xd0 (cx88[0])
cx88[0]/0: found at 0000:05:08.0, rev: 5, irq: 21, latency: 32, mmio: 
0xd8000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
tuner' 2-0068: tuner type not set
cx88[0]/2: cx2388x 8802 Driver Manager
ACPI: PCI Interrupt 0000:05:08.2[A] -> Link [APC3] -> GSI 18 (level, 
low) -> IRQ 21
cx88[0]/2: found at 0000:05:08.2, rev: 5, irq: 21, latency: 32, mmio: 
0xd9000000
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (level, 
low) -> IRQ 17
cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: d420:9022, board: TeVii S420 DVB-S [card=73]
cx88[0]/2: cx2388x based DVB/ATSC card
BUG: soft lockup - CPU#0 stuck for 11s! [modprobe:1767]

Pid: 1767, comm: modprobe Not tainted (2.6.24-etchnhalf.1-686 #1)
EIP: 0060:[<c02be0a5>] EFLAGS: 00000286 CPU: 0
EIP is at _spin_lock+0x7/0xf
EAX: [removed]
ESI: [removed]
 DS: [removed]
CR0: [removed]
DR0: [removed]
DR6: [removed]
 [<c02bd4ba>] __mutex_lock_slowpath+0x17/0x7f
 [<c01099da>] sched_clock+0x8/0x18
 [<c02bd39a>] mutex_lock+0xa/0xb
 [<f89d60f7>] videobuf_dvb_get_frontend+0x11/0x37 [videobuf_dvb]
 [<f8a4e3b2>] cx8802_dvb_probe+0xef/0x1a15 [cx88_dvb]
 [<c0121da0>] check_preempt_wakeup+0x1e/0x7a
 [<f89de540>] cx8802_register_driver+0x128/0x1e3 [ex8802]
 [<c01437ab>] sys_int_module+0x15e3/0x16fb
 [<c0164172>] vma_prio_tree_insert+0x17/0x2a
 [<c012c887>] msleep+0x0/0x12
 [<c0103e66>] sysenter_past_esp+0x6b/0xa1
==============================

Only way i can boot my system is to remove the PCI card.

So then i tried using the drivers from TeVii ( 
http://www.tevii.com/Tevii_linuxdriver_0815.rar )
These actually work but are based on what seems to be a v4l-dvb checkout 
from 2008-08-14.

I can't use these old drivers because they conflict with other v4l-dvb 
modules i want to load for other tuner cards.

Is there someway i can get the TeVii S420 working on the latest v4l-dvb 
modules?

Also using the old drivers, just the following happens on boot

-----------
cx88[0]/2: subsystem: d420:9022, board: TeVii S420 DVB-S [card=73]
cx88[0]/2: cx2388x based DVB/ATSC card
intel8x0_measure_ac97_clock: measured 54726 usecs
intel8x0: clocking to 46908
stv0288 id 11
DVB: registering new adapter (cx88[0])
DVB: registering frontend 0 (ST STV0288 DVB-S)...
-----------
Could this perhaps be an issue with the intel8x0 module?



-------------------------------------------------

Re: kernel soft lockup on boot loading cx2388x based DVB-S card (TeVii S420)

[Alec Christie]

I am getting the same with the Haupauge HVR-4000 after a recent Kernel
Upgrade in Ubuntu Hardy (8.04).

Any help greatly appreciated.

Alec Christie



2009/1/15 Aaron Theodore <aaron@bat.id.au>
>
> Hi I'm running Debian with kernel: 2.6.24-etchnhalf.1-686
> I recently baught a TeVii S420 DVB-S card and have been tring to get it to work.
>
> Firstly i built the v4l from: http://linuxtv.org/hg/v4l-dvb (hg clone) as the card was not detected.
> On first reboot after new modules are installed i get a kernel soft lockup....
>
> -------------------------------------------------
> Linux video capture interface: v2.00
> cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
> ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
> ACPI: PCI Interrupt 0000:05:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 21
> cx88[0]: subsystem: d420:9022, board: TeVii S420 DVB-S [card=73,autodetected], frontend(s): 1
> cx88[0]: TV tuner type -1, Radio tuner type -1
> cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
> tuner' 2-0068: chip found @ 0xd0 (cx88[0])
> cx88[0]/0: found at 0000:05:08.0, rev: 5, irq: 21, latency: 32, mmio: 0xd8000000
> cx88[0]/0: registered device video0 [v4l2]
> cx88[0]/0: registered device vbi0
> tuner' 2-0068: tuner type not set
> cx88[0]/2: cx2388x 8802 Driver Manager
> ACPI: PCI Interrupt 0000:05:08.2[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 21
> cx88[0]/2: found at 0000:05:08.2, rev: 5, irq: 21, latency: 32, mmio: 0xd9000000
> ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
> ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (level, low) -> IRQ 17
> cx88/2: cx2388x dvb driver version 0.0.6 loaded
> cx88/2: registering cx8802 driver, type: dvb access: shared
> cx88[0]/2: subsystem: d420:9022, board: TeVii S420 DVB-S [card=73]
> cx88[0]/2: cx2388x based DVB/ATSC card
> BUG: soft lockup - CPU#0 stuck for 11s! [modprobe:1767]
>
> Pid: 1767, comm: modprobe Not tainted (2.6.24-etchnhalf.1-686 #1)
> EIP: 0060:[<c02be0a5>] EFLAGS: 00000286 CPU: 0
> EIP is at _spin_lock+0x7/0xf
> EAX: [removed]
> ESI: [removed]
> DS: [removed]
> CR0: [removed]
> DR0: [removed]
> DR6: [removed]
> [<c02bd4ba>] __mutex_lock_slowpath+0x17/0x7f
> [<c01099da>] sched_clock+0x8/0x18
> [<c02bd39a>] mutex_lock+0xa/0xb
> [<f89d60f7>] videobuf_dvb_get_frontend+0x11/0x37 [videobuf_dvb]
> [<f8a4e3b2>] cx8802_dvb_probe+0xef/0x1a15 [cx88_dvb]
> [<c0121da0>] check_preempt_wakeup+0x1e/0x7a
> [<f89de540>] cx8802_register_driver+0x128/0x1e3 [ex8802]
> [<c01437ab>] sys_int_module+0x15e3/0x16fb
> [<c0164172>] vma_prio_tree_insert+0x17/0x2a
> [<c012c887>] msleep+0x0/0x12
> [<c0103e66>] sysenter_past_esp+0x6b/0xa1
> ==============================
>
> Only way i can boot my system is to remove the PCI card.
>
> So then i tried using the drivers from TeVii ( http://www.tevii.com/Tevii_linuxdriver_0815.rar )
> These actually work but are based on what seems to be a v4l-dvb checkout from 2008-08-14.
>
> I can't use these old drivers because they conflict with other v4l-dvb modules i want to load for other tuner cards.
>
> Is there someway i can get the TeVii S420 working on the latest v4l-dvb modules?
>
> Also using the old drivers, just the following happens on boot
>
> -----------
> cx88[0]/2: subsystem: d420:9022, board: TeVii S420 DVB-S [card=73]
> cx88[0]/2: cx2388x based DVB/ATSC card
> intel8x0_measure_ac97_clock: measured 54726 usecs
> intel8x0: clocking to 46908
> stv0288 id 11
> DVB: registering new adapter (cx88[0])
> DVB: registering frontend 0 (ST STV0288 DVB-S)...
> -----------
> Could this perhaps be an issue with the intel8x0 module?
>
>
>
> -------------------------------------------------
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html



--
Regards,

Alec Christie

Re: kernel soft lockup on boot loading cx2388x based DVB-S card (TeVii S420)

[Mauro Carvalho Chehab]

On Thu, 15 Jan 2009 11:25:38 +0000
"Alec Christie" <alec.christie@gmail.com> wrote:

> I am getting the same with the Haupauge HVR-4000 after a recent Kernel
> Upgrade in Ubuntu Hardy (8.04).
> 
> Any help greatly appreciated.
> 
> Alec Christie
> 
> 
> 
> 2009/1/15 Aaron Theodore <aaron@bat.id.au>
> >
> > Hi I'm running Debian with kernel: 2.6.24-etchnhalf.1-686
> > I recently baught a TeVii S420 DVB-S card and have been tring to get it to work.
> >
> > Firstly i built the v4l from: http://linuxtv.org/hg/v4l-dvb (hg clone) as the card was not detected.
> > On first reboot after new modules are installed i get a kernel soft lockup....
> > cx88[0]/2: cx2388x based DVB/ATSC card
> > BUG: soft lockup - CPU#0 stuck for 11s! [modprobe:1767]

I just merged on http://linuxtv.org/hg/v4l-dvb a patch for fixing this bug. Please test.

Cheers,
Mauro

Re: kernel soft lockup on boot loading cx2388x based DVB-S card (TeVii S420)

[Mauro Carvalho Chehab]

On Fri, 16 Jan 2009 06:56:05 +1100
Aaron Theodore <aaron@bat.id.au> wrote:

> Mauro,
> 
> Thanks for the speedy patch!

You should thanks to Andy. He is the author of this patch ;)

> My system can at least boot now, but has issues loading the frontend.
> DVB: Unable to find symbol stv0299_attach()
> DVB: Unable to find symbol stv0288_attach()

It seems that you didn't compile those two frontends.

Cheers,
Mauro