* Hauppauge HVR 1110 and DVB
@ 2009-05-19 10:29 Antonio Beamud Montero
2009-05-19 23:48 ` hermann pitton
2009-05-20 13:08 ` Michael Krufky
0 siblings, 2 replies; 7+ messages in thread
From: Antonio Beamud Montero @ 2009-05-19 10:29 UTC (permalink / raw)
To: Linux and Kernel Video
I have a new hauppauge hvr 1110. Trying to load the lastest modules, all
seems to load fine, but no dvb-t frontend is created. As I can see this
card isn't exactly the same hvr 1110 (hvr 1110r3) supported by v4l-dvb.
The system reports the next info:
# lspci -v
0b:03.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135
Video Broadcast Decoder (rev d1)
Subsystem: Hauppauge computer works Inc. Unknown device 6707
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (21000ns min, 8000ns max)
Interrupt: pin A routed to IRQ 114
Region 0: Memory at fc4ff800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
# dmesg
ACPI: PCI Interrupt 0000:0f:03.0[A] -> GSI 160 (level, low) -> IRQ 65
saa7133[0]: found at 0000:0f:03.0, rev: 209, irq: 65, latency: 32, mmio:
0xfc4ff800
saa7133[0]: subsystem: 0070:6707, board: Hauppauge WinTV-HVR1110r3
[card=156,autodetected]
saa7133[0]: board init: gpio is 40000
saa7133[0]: i2c eeprom 00: 70 00 07 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 b0 ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff 35 00 c0 96 10 06 32 97 04 00 20 00 ff ff ff
saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 08 79 5e f0 73 05 29 00
saa7133[0]: i2c eeprom 90: 84 08 00 06 89 06 01 00 95 19 8d 72 07 70 73 09
saa7133[0]: i2c eeprom a0: 23 5f 73 0a f4 9b 72 0b 2f 72 0e 01 72 0f 01 72
saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 73 13 a2 69 79 1a 00 00 00 00 00
saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 0-0050: Hauppauge model 67209, rev C1F5, serial# 6191368
tveeprom 0-0050: MAC address is 00-0D-FE-5E-79-08
tveeprom 0-0050: tuner model is NXP 18271C2 (idx 155, type 54)
tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)
ATSC/DVB Digital (eeprom 0xf4)
tveeprom 0-0050: audio processor is SAA7131 (idx 41)
tveeprom 0-0050: decoder processor is SAA7131 (idx 35)
tveeprom 0-0050: has radio, has IR receiver, has no IR transmitter
saa7133[0]: hauppauge eeprom: model=67209
tuner 0-004b: chip found @ 0x96 (saa7133[0])
tda829x 0-004b: setting tuner address to 60
tda18271 0-0060: creating new instance
TDA18271HD/C2 detected @ 0-0060
tda18271: performing RF tracking filter calibration
tda18271: RF tracking filter calibration complete
tda829x 0-004b: type set to tda8290+18271
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xfc4ff800 irq 65 registered as card -1
Trying to load manually the saa7134-dvb module reports nothing.
The module seems to recognize the 67209LF rev C1F5 ok.
Hauppauge hvr 1110 Hardware Info:
Decoder: saa7131E/03/G
Module: TDA10048HN
(http://www.ecnasiamag.com/article-10192-philipstda10048hnenablesdigitaltvviewingthroughentertainmentdevices-Asia.html)
Greetings
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Hauppauge HVR 1110 and DVB
2009-05-19 10:29 Hauppauge HVR 1110 and DVB Antonio Beamud Montero
@ 2009-05-19 23:48 ` hermann pitton
2009-05-20 13:08 ` Michael Krufky
1 sibling, 0 replies; 7+ messages in thread
From: hermann pitton @ 2009-05-19 23:48 UTC (permalink / raw)
To: Antonio Beamud Montero; +Cc: Linux and Kernel Video, linux-media
Hi Antonio,
Am Dienstag, den 19.05.2009, 12:29 +0200 schrieb Antonio Beamud Montero:
> I have a new hauppauge hvr 1110. Trying to load the lastest modules, all
> seems to load fine, but no dvb-t frontend is created. As I can see this
> card isn't exactly the same hvr 1110 (hvr 1110r3) supported by v4l-dvb.
> The system reports the next info:
we moved to linux-media@vger.kernel.org
Michael Krufky has added support for these new tuners and cards and
Steven Toth for the tda10048.
But it is correct, DVB is not yet enabled on them.
Maybe Michael can give you some hints on what he is still working to do
so and if he might call for testers once.
Cheers,
Hermann
> # lspci -v
>
> 0b:03.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135
> Video Broadcast Decoder (rev d1)
> Subsystem: Hauppauge computer works Inc. Unknown device 6707
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (21000ns min, 8000ns max)
> Interrupt: pin A routed to IRQ 114
> Region 0: Memory at fc4ff800 (32-bit, non-prefetchable) [size=2K]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
>
> # dmesg
>
> ACPI: PCI Interrupt 0000:0f:03.0[A] -> GSI 160 (level, low) -> IRQ 65
> saa7133[0]: found at 0000:0f:03.0, rev: 209, irq: 65, latency: 32, mmio:
> 0xfc4ff800
> saa7133[0]: subsystem: 0070:6707, board: Hauppauge WinTV-HVR1110r3
> [card=156,autodetected]
> saa7133[0]: board init: gpio is 40000
> saa7133[0]: i2c eeprom 00: 70 00 07 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
> saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff
> saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 b0 ff ff ff ff
> saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> saa7133[0]: i2c eeprom 40: ff 35 00 c0 96 10 06 32 97 04 00 20 00 ff ff ff
> saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 08 79 5e f0 73 05 29 00
> saa7133[0]: i2c eeprom 90: 84 08 00 06 89 06 01 00 95 19 8d 72 07 70 73 09
> saa7133[0]: i2c eeprom a0: 23 5f 73 0a f4 9b 72 0b 2f 72 0e 01 72 0f 01 72
> saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 73 13 a2 69 79 1a 00 00 00 00 00
> saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> tveeprom 0-0050: Hauppauge model 67209, rev C1F5, serial# 6191368
> tveeprom 0-0050: MAC address is 00-0D-FE-5E-79-08
> tveeprom 0-0050: tuner model is NXP 18271C2 (idx 155, type 54)
> tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)
> ATSC/DVB Digital (eeprom 0xf4)
> tveeprom 0-0050: audio processor is SAA7131 (idx 41)
> tveeprom 0-0050: decoder processor is SAA7131 (idx 35)
> tveeprom 0-0050: has radio, has IR receiver, has no IR transmitter
> saa7133[0]: hauppauge eeprom: model=67209
> tuner 0-004b: chip found @ 0x96 (saa7133[0])
> tda829x 0-004b: setting tuner address to 60
> tda18271 0-0060: creating new instance
> TDA18271HD/C2 detected @ 0-0060
> tda18271: performing RF tracking filter calibration
> tda18271: RF tracking filter calibration complete
> tda829x 0-004b: type set to tda8290+18271
> saa7133[0]: registered device video0 [v4l2]
> saa7133[0]: registered device vbi0
> saa7133[0]: registered device radio0
> saa7134 ALSA driver for DMA sound loaded
> saa7133[0]/alsa: saa7133[0] at 0xfc4ff800 irq 65 registered as card -1
>
> Trying to load manually the saa7134-dvb module reports nothing.
>
> The module seems to recognize the 67209LF rev C1F5 ok.
>
> Hauppauge hvr 1110 Hardware Info:
>
> Decoder: saa7131E/03/G
> Module: TDA10048HN
> (http://www.ecnasiamag.com/article-10192-philipstda10048hnenablesdigitaltvviewingthroughentertainmentdevices-Asia.html)
>
> Greetings
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Hauppauge HVR 1110 and DVB
2009-05-19 10:29 Hauppauge HVR 1110 and DVB Antonio Beamud Montero
2009-05-19 23:48 ` hermann pitton
@ 2009-05-20 13:08 ` Michael Krufky
2009-05-20 15:42 ` Antonio Beamud Montero
1 sibling, 1 reply; 7+ messages in thread
From: Michael Krufky @ 2009-05-20 13:08 UTC (permalink / raw)
To: Antonio Beamud Montero; +Cc: Linux and Kernel Video, linux-media
On Tue, May 19, 2009 at 6:29 AM, Antonio Beamud Montero
<antonio.beamud@gmail.com> wrote:
> I have a new hauppauge hvr 1110. Trying to load the lastest modules, all
> seems to load fine, but no dvb-t frontend is created. As I can see this card
> isn't exactly the same hvr 1110 (hvr 1110r3) supported by v4l-dvb.
> The system reports the next info:
>
> # lspci -v
>
> 0b:03.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135 Video
> Broadcast Decoder (rev d1)
> Subsystem: Hauppauge computer works Inc. Unknown device 6707
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 32 (21000ns min, 8000ns max)
> Interrupt: pin A routed to IRQ 114
> Region 0: Memory at fc4ff800 (32-bit, non-prefetchable) [size=2K]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
>
> # dmesg
>
> ACPI: PCI Interrupt 0000:0f:03.0[A] -> GSI 160 (level, low) -> IRQ 65
> saa7133[0]: found at 0000:0f:03.0, rev: 209, irq: 65, latency: 32, mmio:
> 0xfc4ff800
> saa7133[0]: subsystem: 0070:6707, board: Hauppauge WinTV-HVR1110r3
> [card=156,autodetected]
> saa7133[0]: board init: gpio is 40000
> saa7133[0]: i2c eeprom 00: 70 00 07 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
> saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff
> saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 b0 ff ff ff ff
> saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> saa7133[0]: i2c eeprom 40: ff 35 00 c0 96 10 06 32 97 04 00 20 00 ff ff ff
> saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 08 79 5e f0 73 05 29 00
> saa7133[0]: i2c eeprom 90: 84 08 00 06 89 06 01 00 95 19 8d 72 07 70 73 09
> saa7133[0]: i2c eeprom a0: 23 5f 73 0a f4 9b 72 0b 2f 72 0e 01 72 0f 01 72
> saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 73 13 a2 69 79 1a 00 00 00 00 00
> saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> tveeprom 0-0050: Hauppauge model 67209, rev C1F5, serial# 6191368
> tveeprom 0-0050: MAC address is 00-0D-FE-5E-79-08
> tveeprom 0-0050: tuner model is NXP 18271C2 (idx 155, type 54)
> tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)
> ATSC/DVB Digital (eeprom 0xf4)
> tveeprom 0-0050: audio processor is SAA7131 (idx 41)
> tveeprom 0-0050: decoder processor is SAA7131 (idx 35)
> tveeprom 0-0050: has radio, has IR receiver, has no IR transmitter
> saa7133[0]: hauppauge eeprom: model=67209
> tuner 0-004b: chip found @ 0x96 (saa7133[0])
> tda829x 0-004b: setting tuner address to 60
> tda18271 0-0060: creating new instance
> TDA18271HD/C2 detected @ 0-0060
> tda18271: performing RF tracking filter calibration
> tda18271: RF tracking filter calibration complete
> tda829x 0-004b: type set to tda8290+18271
> saa7133[0]: registered device video0 [v4l2]
> saa7133[0]: registered device vbi0
> saa7133[0]: registered device radio0
> saa7134 ALSA driver for DMA sound loaded
> saa7133[0]/alsa: saa7133[0] at 0xfc4ff800 irq 65 registered as card -1
>
> Trying to load manually the saa7134-dvb module reports nothing.
>
> The module seems to recognize the 67209LF rev C1F5 ok.
>
> Hauppauge hvr 1110 Hardware Info:
>
> Decoder: saa7131E/03/G
> Module: TDA10048HN
> (http://www.ecnasiamag.com/article-10192-philipstda10048hnenablesdigitaltvviewingthroughentertainmentdevices-Asia.html)
Hello,
I specifically left out the DVB support for this device.
To be honest, I didn't know that this board was available for purchase
already. Where did you get it? (just curious)
I like to add card support for all products as soon as possible. In
the case of this board, analog works but digital does not yet.
I'm a bit busy at the moment ... Try again in a few weeks to a month
or so and there should be more progress.
If something happens sooner than that, I'll append another email to this thread.
Regards,
Mike
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Hauppauge HVR 1110 and DVB
2009-05-20 13:08 ` Michael Krufky
@ 2009-05-20 15:42 ` Antonio Beamud Montero
2009-05-20 19:19 ` Michael Krufky
0 siblings, 1 reply; 7+ messages in thread
From: Antonio Beamud Montero @ 2009-05-20 15:42 UTC (permalink / raw)
To: Michael Krufky; +Cc: Linux and Kernel Video, linux-media
Michael Krufky escribió:
> On Tue, May 19, 2009 at 6:29 AM, Antonio Beamud Montero
>
> Hello,
>
> I specifically left out the DVB support for this device.
>
> To be honest, I didn't know that this board was available for purchase
> already. Where did you get it? (just curious)
>
It seems that here in spain is available :)
>
> If something happens sooner than that, I'll append another email to this thread.
>
Ok, If you need a tester, I'm your man ;)
Thank you.
Greetings.
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Hauppauge HVR 1110 and DVB
2009-05-20 15:42 ` Antonio Beamud Montero
@ 2009-05-20 19:19 ` Michael Krufky
2009-05-21 14:13 ` Antonio Beamud Montero
0 siblings, 1 reply; 7+ messages in thread
From: Michael Krufky @ 2009-05-20 19:19 UTC (permalink / raw)
To: Antonio Beamud Montero; +Cc: Linux and Kernel Video, linux-media
On Wed, May 20, 2009 at 11:42 AM, Antonio Beamud Montero
<antonio.beamud@gmail.com> wrote:
> Michael Krufky escribió:
>>
>> On Tue, May 19, 2009 at 6:29 AM, Antonio Beamud Montero
>> Hello,
>>
>> I specifically left out the DVB support for this device.
>>
>> To be honest, I didn't know that this board was available for purchase
>> already. Where did you get it? (just curious)
>>
>
> It seems that here in spain is available :)
>
>
>>
>> If something happens sooner than that, I'll append another email to this
>> thread.
>>
>
> Ok, If you need a tester, I'm your man ;)
>
> Thank you.
>
> Greetings.
(i am sending this a second time -- first message got rejected by vger)
You're in luck -- I resolved the problem today... If you'd like to
test, please try out this repository:
http://kernellabs.com/hg/~mk/hvr1110
Please let me know how this works for you.
Regards,
Mike Krufky
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Hauppauge HVR 1110 and DVB
2009-05-20 19:19 ` Michael Krufky
@ 2009-05-21 14:13 ` Antonio Beamud Montero
2009-05-21 15:24 ` Michael Krufky
0 siblings, 1 reply; 7+ messages in thread
From: Antonio Beamud Montero @ 2009-05-21 14:13 UTC (permalink / raw)
To: Michael Krufky; +Cc: Linux and Kernel Video, linux-media
Michael Krufky escribió:
> On Wed, May 20, 2009 at 11:42 AM, Antonio Beamud Montero
> <antonio.beamud@gmail.com> wrote:
>
>> Michael Krufky escribió:
>>
>>> On Tue, May 19, 2009 at 6:29 AM, Antonio Beamud Montero
>>> Hello,
>>>
>>> I specifically left out the DVB support for this device.
>>>
>>> To be honest, I didn't know that this board was available for purchase
>>> already. Where did you get it? (just curious)
>>>
>>>
>> It seems that here in spain is available :)
>>
>>
>>
>>> If something happens sooner than that, I'll append another email to this
>>> thread.
>>>
>>>
>> Ok, If you need a tester, I'm your man ;)
>>
>> Thank you.
>>
>> Greetings.
>>
>
> (i am sending this a second time -- first message got rejected by vger)
>
> You're in luck -- I resolved the problem today... If you'd like to
> test, please try out this repository:
>
> http://kernellabs.com/hg/~mk/hvr1110
>
> Please let me know how this works for you.
>
>
Thanks for the patch. Seems to load fine, the problem arises when try
load the firmware.
--------
saa7133[0]: found at 0000:0f:03.0, rev: 209, irq: 65, latency: 32, mmio:
0xfc4ff800
saa7133[0]: subsystem: 0070:6707, board: Hauppauge WinTV-HVR1110r3
DVB-T/Hybrid [card=156,autodetected]
saa7133[0]: board init: gpio is 440100
tuner 0-004b: chip found @ 0x96 (saa7133[0])
saa7133[0]: i2c eeprom 00: 70 00 07 67 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 b0 ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff 35 00 c0 96 10 06 32 97 04 00 20 00 ff ff ff
saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 08 79 5e f0 73 05 29 00
saa7133[0]: i2c eeprom 90: 84 08 00 06 89 06 01 00 95 19 8d 72 07 70 73 09
saa7133[0]: i2c eeprom a0: 23 5f 73 0a f4 9b 72 0b 2f 72 0e 01 72 0f 01 72
saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 73 13 a2 69 79 1a 00 00 00 00 00
saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tveeprom 0-0050: Hauppauge model 67209, rev C1F5, serial# 6191368
tveeprom 0-0050: MAC address is 00-0D-FE-5E-79-08
tveeprom 0-0050: tuner model is NXP 18271C2 (idx 155, type 54)
tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K)
ATSC/DVB Digital (eeprom 0xf4)
tveeprom 0-0050: audio processor is SAA7131 (idx 41)
tveeprom 0-0050: decoder processor is SAA7131 (idx 35)
tveeprom 0-0050: has radio, has IR receiver, has no IR transmitter
saa7133[0]: hauppauge eeprom: model=67209
tda829x 0-004b: setting tuner address to 60
tda18271 0-0060: creating new instance
TDA18271HD/C2 detected @ 0-0060
tda18271: performing RF tracking filter calibration
tda18271: RF tracking filter calibration complete
tda829x 0-004b: type set to tda8290+18271
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
dvb_init() allocating 1 frontend
tda829x 0-004b: type set to tda8290
tda18271 0-0060: attaching existing instance
DVB: registering new adapter (saa7133[0])
DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)...
tda10048_firmware_upload: waiting for firmware upload
(dvb-fe-tda10048-1.0.fw)...
tda10048_firmware_upload: firmware read 24878 bytes.
tda10048_firmware_upload: firmware uploading
tda10048_firmware_upload: firmware upload failed
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xfc4ff800 irq 65 registered as card -1
---
I've tried to extract the firmware from the windows drivers, but all my
experiments failed.
How I can get the correct firmware?
Thanks for all again.
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Hauppauge HVR 1110 and DVB
2009-05-21 14:13 ` Antonio Beamud Montero
@ 2009-05-21 15:24 ` Michael Krufky
0 siblings, 0 replies; 7+ messages in thread
From: Michael Krufky @ 2009-05-21 15:24 UTC (permalink / raw)
To: Antonio Beamud Montero; +Cc: Linux and Kernel Video, linux-media
On Thu, May 21, 2009 at 10:13 AM, Antonio Beamud Montero
<antonio.beamud@gmail.com> wrote:
> Thanks for the patch. Seems to load fine, the problem arises when try load
> the firmware.
[snip]
> DVB: registering new adapter (saa7133[0])
> DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)...
> tda10048_firmware_upload: waiting for firmware upload
> (dvb-fe-tda10048-1.0.fw)...
> tda10048_firmware_upload: firmware read 24878 bytes.
> tda10048_firmware_upload: firmware uploading
> tda10048_firmware_upload: firmware upload failed
> saa7134 ALSA driver for DMA sound loaded
> saa7133[0]/alsa: saa7133[0] at 0xfc4ff800 irq 65 registered as card -1
>
> ---
>
> I've tried to extract the firmware from the windows drivers, but all my
> experiments failed.
> How I can get the correct firmware?
You can get the firmware from here:
http://www.steventoth.net/linux/hvr1200
Regards,
Mike
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2009-05-21 15:24 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-05-19 10:29 Hauppauge HVR 1110 and DVB Antonio Beamud Montero
2009-05-19 23:48 ` hermann pitton
2009-05-20 13:08 ` Michael Krufky
2009-05-20 15:42 ` Antonio Beamud Montero
2009-05-20 19:19 ` Michael Krufky
2009-05-21 14:13 ` Antonio Beamud Montero
2009-05-21 15:24 ` Michael Krufky
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox