From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from mail.kapsi.fi ([217.30.184.167]:33050 "EHLO mail.kapsi.fi" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1755977AbZIUOAr (ORCPT ); Mon, 21 Sep 2009 10:00:47 -0400 Message-ID: <4AB7870D.3030300@iki.fi> Date: Mon, 21 Sep 2009 17:00:45 +0300 From: Antti Palosaari MIME-Version: 1.0 To: Roman CC: "Aleksandr V. Piskunov" , "linux-media@vger.kernel.org" Subject: Re: MSI Digivox mini III Remote Control References: <200909202026.27086.lists@hasnoname.de> <20090921115122.GA2269@moon> <4AB77329.5000405@iki.fi> <200909211555.11747.lists@hasnoname.de> In-Reply-To: <200909211555.11747.lists@hasnoname.de> Content-Type: text/plain; charset=iso-8859-1; format=flowed Content-Transfer-Encoding: 7bit Sender: linux-media-owner@vger.kernel.org List-ID: Roman wrote: > Am Monday 21 September 2009 14:35:53 schrieb Antti Palosaari: >> On 09/21/2009 02:51 PM, Aleksandr V. Piskunov wrote: >>> Just grab that patch and apply it to the current vl4-dvb, no need to mess >>> with old repository. >>> http://linuxtv.org/hg/~anttip/af9015-digivox3_remote/raw-rev/914ded6d921d >> With this patch remote will not work most likely. But after adding that >> patch you should see remote events dumped to the /var/log/messages when >> key is pressed. I need to know which key gives which code. After that I >> can add correct key mappings to the driver. >> >> Antti > > I don't get anything else in the logs than this, even with the patch applied: > #--- > Sep 21 15:43:04 Seth usbcore: registered new interface driver dvb_usb_af9015 > Sep 21 15:43:07 Seth usb 1-5: new high speed USB device using ehci_hcd and > address 4 > Sep 21 15:43:08 Seth usb 1-5: configuration #1 chosen from 1 choice > Sep 21 15:43:08 Seth dvb-usb: found a 'MSI Digi VOX mini III' in cold state, > will try to load a firmware > Sep 21 15:43:08 Seth usb 1-5: firmware: requesting dvb-usb-af9015.fw > Sep 21 15:43:08 Seth dvb-usb: downloading firmware from > file 'dvb-usb-af9015.fw' > Sep 21 15:43:08 Seth dvb-usb: found a 'MSI Digi VOX mini III' in warm state. > Sep 21 15:43:08 Seth dvb-usb: will pass the complete MPEG2 transport stream to > the software demuxer. > Sep 21 15:43:08 Seth DVB: registering new adapter (MSI Digi VOX mini III) > Sep 21 15:43:08 Seth af9013: firmware version:4.95.0 > Sep 21 15:43:08 Seth DVB: registering adapter 0 frontend 0 (Afatech AF9013 > DVB-T)... > Sep 21 15:43:08 Seth tda18271 3-00c0: creating new instance > Sep 21 15:43:08 Seth TDA18271HD/C1 detected @ 3-00c0 > Sep 21 15:43:08 Seth dvb-usb: MSI Digi VOX mini III successfully initialized > and connected. > Sep 21 15:43:51 Seth [drm] LVDS-8: set mode 1024x768 10 > #--- For reason or the other there is no any mention about remote polling. Could you enable debug=3 to see what eeprom value is set to remote? rmmod dvb-usb-af9015; modprobe dvb-usb-af9015 debug=3; Antti -- http://palosaari.fi/