* HP/Yuan EC372S DVB-T
@ 2009-10-19 21:19 Patryk Ściborek
2009-10-19 23:26 ` Antti Palosaari
0 siblings, 1 reply; 4+ messages in thread
From: Patryk Ściborek @ 2009-10-19 21:19 UTC (permalink / raw)
To: linux-media
Hello,
I have HP/Yuan EC372S DVB-T tuner. I'm trying to make it working under
Linux but without success. I've tried using modules from 2.6.31.3 and
compiling from Mercurial repository.
Just after inserting card (modules have debugging enabled):
karaluszek:/lib/modules# dmesg | grep -v '>>>' | grep -v '<<<' | grep -v 'writing to address' | tail -36
[85050.640892] dvb-usb: Yuan EC372S successfully deinitialized and disconnected.
[85054.324234] usb 3-3: new high speed USB device using ehci_hcd and address 9
[85054.457258] usb 3-3: New USB device found, idVendor=1164, idProduct=1edc
[85054.457269] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[85054.457275] usb 3-3: Product: STK7700D
[85054.457280] usb 3-3: Manufacturer: YUANRD
[85054.457284] usb 3-3: SerialNumber: 0000000001
[85054.457484] usb 3-3: configuration #1 chosen from 1 choice
[85054.458505] FW GET_VERSION length: -32
[85054.458511] cold: 1
[85054.458515] dvb-usb: found a 'Yuan EC372S' in cold state, will try to load a firmware
[85054.458522] usb 3-3: firmware: requesting dvb-usb-dib0700-1.20.fw
[85054.478061] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw'
[85054.684318] dib0700: firmware started successfully.
[85055.188223] dvb-usb: found a 'Yuan EC372S' in warm state.
[85055.188348] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[85055.188817] DVB: registering new adapter (Yuan EC372S)
[85055.236479] ep 0 write error (status = -32, len: 6)
[85055.236481] DiB7000P: checking demod on I2C address: 128 (80)
[85055.236976] ep 0 read error (status = -32)
[85055.236979] I2C read failed on address 0x40
[85055.236981] DiB7000P: i2c read error on 768
[85055.236983] DiB7000P: wrong Vendor ID (read=0x1200)
[85055.238348] DiB7000P: checking demod on I2C address: 18 (12)
[85055.242480] DiB7000P: setting output mode for demod ffff88007a47b2f0 to 4
[85055.247474] DiB7000P: IC 0 initialized (to i2c_address 0x80)
[85055.250101] DiB7000P: setting output mode for demod ffff88007a47b2f0 to 0
[85055.255865] DiB7000P: checking demod on I2C address: 128 (80)
[85055.296360] DiB7000P: gpio dir: ffff: val: 0, pwm_pos: ffff
[85055.302743] DiB7000P: setting output mode for demod ffff8800300e3000 to 0
[85055.309721] DiB7000P: using default timf
[85055.408997] DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)...
[85055.412746] MT2266: successfully identified
[85055.574944] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:1d.7/usb3/3-3/input/input19
[85055.575048] dvb-usb: schedule remote query interval to 50 msecs.
[85055.575055] dvb-usb: Yuan EC372S successfully initialized and connected.
karaluszek:/lib/modules# uname -a
Linux karaluszek 2.6.31.3-scibi #1 SMP Sun Oct 11 23:38:13 CEST 2009 x86_64 GNU/Linux
After running dvbscan/dvbtune:
karaluszek:/home/scibi/dvb/v4l-dvb-f6680fa8e7ec# dvbscan /usr/share/dvb/dvb-t/pl-Warszawa
Unable to query frontend status
karaluszek:/home/scibi/dvb/v4l-dvb-f6680fa8e7ec# dvbtune -f 690000000
Using DVB card "DiBcom 7000PC"
tuning DVB-T (in United Kingdom) to 690000000 Hz
polling....
Getting frontend event
FE_STATUS:
polling....
polling....
^C
[85473.793547] DiB7000P: setting output mode for demod ffff8800300e3000 to 0
[85473.819971] MT2266: set_parms: tune=376832 band=102 UHF
[85473.819978] MT2266: set_parms: [1..3]: 0 0 2e
[85473.887700] MT2266: Lock when i=3
[85473.913806] DiB7000P: WBD: ref: 3530, sel: 1, active: 0, alpha: 1
[85473.960080] DiB7000P: using default timf
[85474.261493] DiB7000P: using default timf
[85474.265451] DiB7000P: setting output mode for demod ffff8800300e3000 to 5
[85474.277844] DiB7000P: setting output mode for demod ffff8800300e3000 to 0
[85479.607362] DiB7000P: setting output mode for demod ffff8800300e3000 to 0
[85479.631733] MT2266: set_parms: tune=376832 band=102 UHF
[85479.631735] MT2266: set_parms: [1..3]: 0 0 2e
[85479.718610] MT2266: Lock when i=4
[85479.772081] DiB7000P: using default timf
[85480.073558] DiB7000P: using default timf
[85480.077638] DiB7000P: setting output mode for demod ffff8800300e3000 to 5
[85481.083071] DiB7000P: setting output mode for demod ffff8800300e3000 to 0
[85481.107832] MT2266: set_parms: tune=376832 band=102 UHF
[85481.107839] MT2266: set_parms: [1..3]: 0 0 2e
[85481.179685] MT2266: Lock when i=4
[85481.252064] DiB7000P: using default timf
[85481.553570] DiB7000P: using default timf
[85481.557560] DiB7000P: setting output mode for demod ffff8800300e3000 to 5
[85482.563011] DiB7000P: setting output mode for demod ffff8800300e3000 to 0
[85482.587880] MT2266: set_parms: tune=376832 band=102 UHF
[85482.587887] MT2266: set_parms: [1..3]: 0 0 2e
[85482.663631] MT2266: Lock when i=4
[85482.720715] DiB7000P: using default timf
[85483.021653] DiB7000P: using default timf
[85483.025607] DiB7000P: setting output mode for demod ffff8800300e3000 to 5
[85484.031060] DiB7000P: setting output mode for demod ffff8800300e3000 to 0
[85484.055926] MT2266: set_parms: tune=376832 band=102 UHF
[85484.055939] MT2266: set_parms: [1..3]: 0 0 2e
[85484.127552] MT2266: Lock when i=4
I've done some usb snooping on Windows using
http://sourceforge.net/projects/usbsnoop/ during initialization and
start of playback so I can post it here if it's needed. I can also post
not filtered dmesg output.
karaluszek:/lib/modules# lsusb -s 3:9 -v
Bus 003 Device 009: ID 1164:1edc YUAN High-Tech Development Co., Ltd
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1164 YUAN High-Tech Development Co., Ltd
idProduct 0x1edc
bcdDevice 1.00
iManufacturer 1 YUANRD
iProduct 2 STK7700D
iSerial 3 0000000001
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 46
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Best regards,
Patryk Ściborek
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: HP/Yuan EC372S DVB-T
2009-10-19 21:19 HP/Yuan EC372S DVB-T Patryk Ściborek
@ 2009-10-19 23:26 ` Antti Palosaari
2009-10-20 16:39 ` Patryk Ściborek
0 siblings, 1 reply; 4+ messages in thread
From: Antti Palosaari @ 2009-10-19 23:26 UTC (permalink / raw)
To: Patryk Ściborek; +Cc: linux-media
On 10/20/2009 12:19 AM, Patryk Ściborek wrote:
> I have HP/Yuan EC372S DVB-T tuner. I'm trying to make it working under
> Linux but without success. I've tried using modules from 2.6.31.3 and
> compiling from Mercurial repository.
I have same device here - not working. Last time I tried it said
something like 'demod enumeration failed' though I am not sure if my
device is working at all. There have been some other reports too that
says this device is not working.
Do you have Windows XP drivers? I think I could fix that device if I get
my device working with Windows. And I only have XP...
regards
Antti
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: HP/Yuan EC372S DVB-T
2009-10-19 23:26 ` Antti Palosaari
@ 2009-10-20 16:39 ` Patryk Ściborek
2009-10-20 20:51 ` Antti Palosaari
0 siblings, 1 reply; 4+ messages in thread
From: Patryk Ściborek @ 2009-10-20 16:39 UTC (permalink / raw)
To: linux-media
Dnia 2009-10-20, wto o godzinie 02:26 +0300, Antti Palosaari pisze:
> Do you have Windows XP drivers? I think I could fix that device if I get
> my device working with Windows. And I only have XP...
Hi,
As far as I remember I've just installed (on XP) drivers from CD. It was
included with the card. I've made a copy:
http://sciborek.com/ec372/windrv.tar.bz2
Regards
Patryk
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: HP/Yuan EC372S DVB-T
2009-10-20 16:39 ` Patryk Ściborek
@ 2009-10-20 20:51 ` Antti Palosaari
0 siblings, 0 replies; 4+ messages in thread
From: Antti Palosaari @ 2009-10-20 20:51 UTC (permalink / raw)
To: Patryk Ściborek; +Cc: linux-media
On 10/20/2009 07:39 PM, Patryk Ściborek wrote:
> Dnia 2009-10-20, wto o godzinie 02:26 +0300, Antti Palosaari pisze:
>
>> Do you have Windows XP drivers? I think I could fix that device if I get
>> my device working with Windows. And I only have XP...
>
> Hi,
>
> As far as I remember I've just installed (on XP) drivers from CD. It was
> included with the card. I've made a copy:
>
> http://sciborek.com/ec372/windrv.tar.bz2
Thanks. Now I found why I was failing earlier - it was due to USB2.0
ExpressCard adapter I was using... :-( After I plugged it to Linux
laptop native ExpressCard slot it attachs demod. Tuning is still always
failing with filter timeouts. I even opened my box, there is DiBcom
7700C1-ACXXa-G and Microtune MT2266F. I will hack that more later.
regards
Antti
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2009-10-20 20:51 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-10-19 21:19 HP/Yuan EC372S DVB-T Patryk Ściborek
2009-10-19 23:26 ` Antti Palosaari
2009-10-20 16:39 ` Patryk Ściborek
2009-10-20 20:51 ` Antti Palosaari
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox