* Remote for Terratec Cinergy C PCI HD (DVB-C)
@ 2010-01-20 22:15 Hans-Peter Wolf
2010-01-21 17:33 ` Hans-Peter Wolf
0 siblings, 1 reply; 4+ messages in thread
From: Hans-Peter Wolf @ 2010-01-20 22:15 UTC (permalink / raw)
To: linux-media
Hi,
I installed the mantis driver from the v4l-dvb mercurial repository and
got my tv-card Terratec Cinergy C PCI HD running successfully.
However, I cannot find any information if the included remote, which
also directly connected to the PCI card, is also working. The dmesg
output gives me these lines at the startup (not comparable to the lines
listed on linuxtv.org):
[ 7.402278] Mantis 0000:01:06.0: PCI INT A -> Link[LNKA] -> GSI 16
(level, low) -> IRQ 16
[ 7.403356] DVB: registering new adapter (Mantis DVB adapter)
[ 8.322027] DVB: registering adapter 0 frontend 0 (Philips TDA10023
DVB-C)...
(I also had to add the module 'mantis' to /etc/modules to run it
automatically at startup. Is this normal?)
I also tried cat /proc/bus/input/devices but couldn't find a plausible
device (output attached below).
Can anyone tell me how to find out if the device is properly installed?
Or better: How to install the remote device? Is there any special module
required?
Thank you very much in advance!
Hans-Peter
cat /proc/bus/input/devices
I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
U: Uniq=
H: Handlers=kbd event0
B: EV=3
B: KEY=10000000000000 0
I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
U: Uniq=
H: Handlers=kbd event1
B: EV=3
B: KEY=10000000000000 0
I: Bus=0017 Vendor=0001 Product=0001 Version=0100
N: Name="Macintosh mouse button emulation"
P: Phys=
S: Sysfs=/devices/virtual/input/input2
U: Uniq=
H: Handlers=mouse0 event2
B: EV=7
B: KEY=70000 0 0 0 0
B: REL=3
I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=/video/input0
S:
Sysfs=/devices/LNXSYSTM:00/device:00/PNP0A03:00/device:12/device:13/input/input3
U: Uniq=
H: Handlers=kbd event3
B: EV=3
B: KEY=3f000b00000000 0 0 0
I: Bus=0003 Vendor=046d Product=c01f Version=0110
N: Name="Logitech USB-PS/2 Optical Mouse"
P: Phys=usb-0000:00:02.0-6/input0
S: Sysfs=/devices/pci0000:00/0000:00:02.0/usb3/3-6/3-6:1.0/input/input4
U: Uniq=
H: Handlers=mouse1 event4
B: EV=17
B: KEY=f0000 0 0 0 0
B: REL=103
B: MSC=10
I: Bus=0003 Vendor=046a Product=0011 Version=0110
N: Name="HID 046a:0011"
P: Phys=usb-0000:00:04.0-6/input0
S: Sysfs=/devices/pci0000:00/0000:00:04.0/usb4/4-6/4-6:1.0/input/input5
U: Uniq=
H: Handlers=kbd event5
B: EV=120013
B: KEY=1000000000007 ff800000000007ff febeffdff3cfffff fffffffffffffffe
B: MSC=10
B: LED=7
I: Bus=0001 Vendor=10ec Product=0888 Version=0001
N: Name="HDA Digital PCBeep"
P: Phys=card0/codec#0/beep0
S: Sysfs=/devices/pci0000:00/0000:00:07.0/input/input6
U: Uniq=
H: Handlers=kbd event6
B: EV=40001
B: SND=6
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Remote for Terratec Cinergy C PCI HD (DVB-C)
2010-01-20 22:15 Remote for Terratec Cinergy C PCI HD (DVB-C) Hans-Peter Wolf
@ 2010-01-21 17:33 ` Hans-Peter Wolf
2010-01-25 20:22 ` MartinG
0 siblings, 1 reply; 4+ messages in thread
From: Hans-Peter Wolf @ 2010-01-21 17:33 UTC (permalink / raw)
To: linux-media
Hi,
I got it finally running! I just took the last s2-liplianin source and
it was detected automatically:
I: Bus=0001 Vendor=0000 Product=0000 Version=0001
N: Name="Mantis VP-2040 IR Receiver"
P: Phys=pci-0000:01:06.0/ir0
S: Sysfs=/devices/virtual/input/input5
U: Uniq=
H: Handlers=kbd event5
B: EV=100003
B: KEY=108fc330 284204100000000 0 2000000018000 218040000801
9e96c000000000 ffc
Strange, that it didn't work with v4l-dvb sources.
Thank you very much. I really appreciate your work!
Regards
Hans-Peter
Hans-Peter Wolf schrieb:
> Hi,
>
> I installed the mantis driver from the v4l-dvb mercurial repository and
> got my tv-card Terratec Cinergy C PCI HD running successfully.
>
> However, I cannot find any information if the included remote, which
> also directly connected to the PCI card, is also working. The dmesg
> output gives me these lines at the startup (not comparable to the lines
> listed on linuxtv.org):
>
> [ 7.402278] Mantis 0000:01:06.0: PCI INT A -> Link[LNKA] -> GSI 16
> (level, low) -> IRQ 16
> [ 7.403356] DVB: registering new adapter (Mantis DVB adapter)
> [ 8.322027] DVB: registering adapter 0 frontend 0 (Philips TDA10023
> DVB-C)...
>
> (I also had to add the module 'mantis' to /etc/modules to run it
> automatically at startup. Is this normal?)
>
> I also tried cat /proc/bus/input/devices but couldn't find a plausible
> device (output attached below).
>
> Can anyone tell me how to find out if the device is properly installed?
> Or better: How to install the remote device? Is there any special module
> required?
>
> Thank you very much in advance!
> Hans-Peter
>
> cat /proc/bus/input/devices
> I: Bus=0019 Vendor=0000 Product=0001 Version=0000
> N: Name="Power Button"
> P: Phys=LNXPWRBN/button/input0
> S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
> U: Uniq=
> H: Handlers=kbd event0
> B: EV=3
> B: KEY=10000000000000 0
>
> I: Bus=0019 Vendor=0000 Product=0001 Version=0000
> N: Name="Power Button"
> P: Phys=PNP0C0C/button/input0
> S: Sysfs=/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
> U: Uniq=
> H: Handlers=kbd event1
> B: EV=3
> B: KEY=10000000000000 0
>
> I: Bus=0017 Vendor=0001 Product=0001 Version=0100
> N: Name="Macintosh mouse button emulation"
> P: Phys=
> S: Sysfs=/devices/virtual/input/input2
> U: Uniq=
> H: Handlers=mouse0 event2
> B: EV=7
> B: KEY=70000 0 0 0 0
> B: REL=3
>
> I: Bus=0019 Vendor=0000 Product=0006 Version=0000
> N: Name="Video Bus"
> P: Phys=/video/input0
> S:
> Sysfs=/devices/LNXSYSTM:00/device:00/PNP0A03:00/device:12/device:13/input/input3
>
> U: Uniq=
> H: Handlers=kbd event3
> B: EV=3
> B: KEY=3f000b00000000 0 0 0
>
> I: Bus=0003 Vendor=046d Product=c01f Version=0110
> N: Name="Logitech USB-PS/2 Optical Mouse"
> P: Phys=usb-0000:00:02.0-6/input0
> S: Sysfs=/devices/pci0000:00/0000:00:02.0/usb3/3-6/3-6:1.0/input/input4
> U: Uniq=
> H: Handlers=mouse1 event4
> B: EV=17
> B: KEY=f0000 0 0 0 0
> B: REL=103
> B: MSC=10
>
> I: Bus=0003 Vendor=046a Product=0011 Version=0110
> N: Name="HID 046a:0011"
> P: Phys=usb-0000:00:04.0-6/input0
> S: Sysfs=/devices/pci0000:00/0000:00:04.0/usb4/4-6/4-6:1.0/input/input5
> U: Uniq=
> H: Handlers=kbd event5
> B: EV=120013
> B: KEY=1000000000007 ff800000000007ff febeffdff3cfffff fffffffffffffffe
> B: MSC=10
> B: LED=7
>
> I: Bus=0001 Vendor=10ec Product=0888 Version=0001
> N: Name="HDA Digital PCBeep"
> P: Phys=card0/codec#0/beep0
> S: Sysfs=/devices/pci0000:00/0000:00:07.0/input/input6
> U: Uniq=
> H: Handlers=kbd event6
> B: EV=40001
> B: SND=6
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Remote for Terratec Cinergy C PCI HD (DVB-C)
2010-01-21 17:33 ` Hans-Peter Wolf
@ 2010-01-25 20:22 ` MartinG
2010-01-25 20:32 ` MartinG
0 siblings, 1 reply; 4+ messages in thread
From: MartinG @ 2010-01-25 20:22 UTC (permalink / raw)
To: linux-media
On Thu, Jan 21, 2010 at 6:33 PM, Hans-Peter Wolf
<hapewolf@googlemail.com> wrote:
> Hi,
>
> I got it finally running! I just took the last s2-liplianin source and it
> was detected automatically:
>
> I: Bus=0001 Vendor=0000 Product=0000 Version=0001
> N: Name="Mantis VP-2040 IR Receiver"
> P: Phys=pci-0000:01:06.0/ir0
> S: Sysfs=/devices/virtual/input/input5
> U: Uniq=
> H: Handlers=kbd event5
> B: EV=100003
> B: KEY=108fc330 284204100000000 0 2000000018000 218040000801 9e96c000000000
> ffc
>
> Strange, that it didn't work with v4l-dvb sources.
>
> Thank you very much. I really appreciate your work!
Hi, I've got the exact same device as you, use the s2-liplianin
driver, and after reading your post I tried the remote as well.
But how do I configure it? Some of the keys are working (arrow keys,
numeric keys, Home, volume, mute), but not all.
Is the remote handled as an input device by X itself? So what file(s)
do I need to change/update?
If you have some working config files, or a nice link, I'd appreciate it :)
Best,
MartinG
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Remote for Terratec Cinergy C PCI HD (DVB-C)
2010-01-25 20:22 ` MartinG
@ 2010-01-25 20:32 ` MartinG
0 siblings, 0 replies; 4+ messages in thread
From: MartinG @ 2010-01-25 20:32 UTC (permalink / raw)
To: linux-media
On Mon, Jan 25, 2010 at 9:22 PM, MartinG <gronslet@gmail.com> wrote:
> Hi, I've got the exact same device as you, use the s2-liplianin
> driver, and after reading your post I tried the remote as well.
> But how do I configure it? Some of the keys are working (arrow keys,
> numeric keys, Home, volume, mute), but not all.
> Is the remote handled as an input device by X itself? So what file(s)
> do I need to change/update?
>
> If you have some working config files, or a nice link, I'd appreciate it :)
Replying to myself; I found that 'xev' give the keycodes for most of
the keys, but not eg. the "OK" key, wich is quite important. Is there
a way to add those? Something I can contribute? Where? :)
And by the way - I too really appreciate the work on the mantis driver!
Best,
MartinG
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2010-01-25 20:32 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-01-20 22:15 Remote for Terratec Cinergy C PCI HD (DVB-C) Hans-Peter Wolf
2010-01-21 17:33 ` Hans-Peter Wolf
2010-01-25 20:22 ` MartinG
2010-01-25 20:32 ` MartinG
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox