* Lost remote after kernel/v4l update cx23885 chipset
@ 2010-01-24 20:07 Timothy D. Lenz
2010-02-01 19:03 ` Timothy D. Lenz
0 siblings, 1 reply; 5+ messages in thread
From: Timothy D. Lenz @ 2010-01-24 20:07 UTC (permalink / raw)
To: linux-media
After updating from kernel 2.6.26.8 to 2.6.32.2 and from v4l of
05/19/2009 to 01/18/2010 I lost remote function with Dvico FusionHDTV7
Dual Express. The driver is loading, but not creating an IR device. Went
over it with awalls on IRC. The log is at: http://pastebin.com/m4b02ff0c
I noticed that in the kern.log there where 2 different ways ir-kbd-i2c
showed up. ir-kbd-i2c no longer shows up when loading drivers.
Jan 17 14:59:32 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
/devices/virtual/input/input5
Jan 17 14:59:32 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
detected at i2c-2/2-006b/ir0 [cx23885[0]]
------------------
Jan 18 17:23:27 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
/devices/virtual/input/input5
Jan 18 17:23:27 LLLx64-32 kernel: Creating IR device irrcv0
Jan 18 17:23:27 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
detected at i2c-1/1-006b/ir0 [cx23885[0]]
Jan 18 18:28:50 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
/devices/virtual/input/input5
Jan 18 18:28:50 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
detected at i2c-2/2-006b/ir0 [cx23885[0]]
------------------
A driver load that worked:
Jan 17 11:22:35 LLLx64-32 kernel: Linux video capture interface: v2.00
Jan 17 11:22:35 LLLx64-32 kernel: cx23885 driver version 0.0.2 loaded
Jan 17 11:22:35 LLLx64-32 kernel: ACPI: PCI Interrupt 0000:02:00.0[A] ->
Link [APC7] -> GSI 16 (level, low) -> IRQ 16
Jan 17 11:22:35 LLLx64-32 kernel: CORE cx23885[0]: subsystem: 18ac:d618,
board: DViCO FusionHDTV7 Dual Express [card=10,autodetected]
Jan 17 11:22:35 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
frontend(s)
Jan 17 11:22:35 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
Jan 17 11:22:35 LLLx64-32 kernel: xc5000 2-0064: creating new instance
Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Successfully identified at
address 0x64
Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Firmware has not been loaded
previously
Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering adapter 0 frontend 0
(Samsung S5H1411 QAM/8VSB Frontend)...
Jan 17 11:22:35 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
frontend(s)
Jan 17 11:22:35 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
Jan 17 11:22:35 LLLx64-32 kernel: xc5000 3-0064: creating new instance
Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Successfully identified at
address 0x64
Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Firmware has not been loaded
previously
Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering adapter 1 frontend 0
(Samsung S5H1411 QAM/8VSB Frontend)...
Jan 17 11:22:35 LLLx64-32 kernel: cx23885_dev_checkrevision() Hardware
revision = 0xb0
Jan 17 11:22:35 LLLx64-32 kernel: cx23885[0]/0: found at 0000:02:00.0,
rev: 2, irq: 16, latency: 0, mmio: 0xfdc00000
Jan 17 11:22:35 LLLx64-32 kernel: PCI: Setting latency timer of device
0000:02:00.0 to 64
Jan 17 11:22:35 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
/devices/virtual/input/input8
Jan 17 11:22:35 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
detected at i2c-2/2-006b/ir0 [cx23885[0]]
Jan 17 11:22:36 LLLx64-32 kernel: xc5000: waiting for firmware upload
(dvb-fe-xc5000-1.6.114.fw)...
Jan 17 11:22:36 LLLx64-32 kernel: firmware: requesting
dvb-fe-xc5000-1.6.114.fw
Jan 17 11:22:36 LLLx64-32 kernel: xc5000: firmware read 12401 bytes.
Jan 17 11:22:36 LLLx64-32 kernel: xc5000: firmware uploading...
Jan 17 11:22:37 LLLx64-32 kernel: xc5000: firmware upload complete...
Jan 17 11:22:37 LLLx64-32 kernel: xc5000: waiting for firmware upload
(dvb-fe-xc5000-1.6.114.fw)...
Jan 17 11:22:37 LLLx64-32 kernel: firmware: requesting
dvb-fe-xc5000-1.6.114.fw
Jan 17 11:22:37 LLLx64-32 kernel: xc5000: firmware read 12401 bytes.
Jan 17 11:22:37 LLLx64-32 kernel: xc5000: firmware uploading...
Jan 17 11:22:39 LLLx64-32 kernel: xc5000: firmware upload complete...
------------------
And what it does now:
Jan 23 17:10:47 LLLx64-32 kernel: Linux video capture interface: v2.00
Jan 23 17:10:47 LLLx64-32 kernel: cx23885 driver version 0.0.2 loaded
Jan 23 17:10:47 LLLx64-32 kernel: cx23885 0000:02:00.0: PCI INT A ->
Link[APC7] -> GSI 16 (level, low) -> IRQ 16
Jan 23 17:10:47 LLLx64-32 kernel: CORE cx23885[0]: subsystem: 18ac:d618,
board: DViCO FusionHDTV7 Dual Express [card=10,autodetected]
Jan 23 17:10:47 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
frontend(s)
Jan 23 17:10:47 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
Jan 23 17:10:47 LLLx64-32 kernel: xc5000 1-0064: creating new instance
Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Successfully identified at
address 0x64
Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Firmware has not been loaded
previously
Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering adapter 0 frontend 0
(Samsung S5H1411 QAM/8VSB Frontend)...
Jan 23 17:10:47 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
frontend(s)
Jan 23 17:10:47 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
Jan 23 17:10:47 LLLx64-32 kernel: xc5000 2-0064: creating new instance
Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Successfully identified at
address 0x64
Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Firmware has not been loaded
previously
Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering adapter 1 frontend 0
(Samsung S5H1411 QAM/8VSB Frontend)...
Jan 23 17:10:47 LLLx64-32 kernel: cx23885_dev_checkrevision() Hardware
revision = 0xb0
Jan 23 17:10:47 LLLx64-32 kernel: cx23885[0]/0: found at 0000:02:00.0,
rev: 2, irq: 16, latency: 0, mmio: 0xfdc00000
Jan 23 17:10:47 LLLx64-32 kernel: cx23885 0000:02:00.0: setting latency
timer to 64
Jan 23 17:10:47 LLLx64-32 kernel: IRQ 16/cx23885[0]: IRQF_DISABLED is
not guaranteed on shared IRQs
I put a zip of some logs at: http://24.255.17.209:2400/vdr-logs/logs.zip
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Lost remote after kernel/v4l update cx23885 chipset
2010-01-24 20:07 Lost remote after kernel/v4l update cx23885 chipset Timothy D. Lenz
@ 2010-02-01 19:03 ` Timothy D. Lenz
2010-02-02 12:23 ` Andy Walls
0 siblings, 1 reply; 5+ messages in thread
From: Timothy D. Lenz @ 2010-02-01 19:03 UTC (permalink / raw)
To: linux-media
On 1/24/2010 1:07 PM, Timothy D. Lenz wrote:
> After updating from kernel 2.6.26.8 to 2.6.32.2 and from v4l of
> 05/19/2009 to 01/18/2010 I lost remote function with Dvico FusionHDTV7
> Dual Express. The driver is loading, but not creating an IR device. Went
> over it with awalls on IRC. The log is at: http://pastebin.com/m4b02ff0c
>
>
> I noticed that in the kern.log there where 2 different ways ir-kbd-i2c
> showed up. ir-kbd-i2c no longer shows up when loading drivers.
>
> Jan 17 14:59:32 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
> /devices/virtual/input/input5
> Jan 17 14:59:32 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
> detected at i2c-2/2-006b/ir0 [cx23885[0]]
> ------------------
> Jan 18 17:23:27 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
> /devices/virtual/input/input5
> Jan 18 17:23:27 LLLx64-32 kernel: Creating IR device irrcv0
> Jan 18 17:23:27 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
> detected at i2c-1/1-006b/ir0 [cx23885[0]]
>
> Jan 18 18:28:50 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
> /devices/virtual/input/input5
> Jan 18 18:28:50 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
> detected at i2c-2/2-006b/ir0 [cx23885[0]]
>
> ------------------
> A driver load that worked:
>
> Jan 17 11:22:35 LLLx64-32 kernel: Linux video capture interface: v2.00
> Jan 17 11:22:35 LLLx64-32 kernel: cx23885 driver version 0.0.2 loaded
> Jan 17 11:22:35 LLLx64-32 kernel: ACPI: PCI Interrupt 0000:02:00.0[A] ->
> Link [APC7] -> GSI 16 (level, low) -> IRQ 16
> Jan 17 11:22:35 LLLx64-32 kernel: CORE cx23885[0]: subsystem: 18ac:d618,
> board: DViCO FusionHDTV7 Dual Express [card=10,autodetected]
> Jan 17 11:22:35 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
> frontend(s)
> Jan 17 11:22:35 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
> Jan 17 11:22:35 LLLx64-32 kernel: xc5000 2-0064: creating new instance
> Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Successfully identified at
> address 0x64
> Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Firmware has not been loaded
> previously
> Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
> Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering adapter 0 frontend 0
> (Samsung S5H1411 QAM/8VSB Frontend)...
> Jan 17 11:22:35 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
> frontend(s)
> Jan 17 11:22:35 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
> Jan 17 11:22:35 LLLx64-32 kernel: xc5000 3-0064: creating new instance
> Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Successfully identified at
> address 0x64
> Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Firmware has not been loaded
> previously
> Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
> Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering adapter 1 frontend 0
> (Samsung S5H1411 QAM/8VSB Frontend)...
> Jan 17 11:22:35 LLLx64-32 kernel: cx23885_dev_checkrevision() Hardware
> revision = 0xb0
> Jan 17 11:22:35 LLLx64-32 kernel: cx23885[0]/0: found at 0000:02:00.0,
> rev: 2, irq: 16, latency: 0, mmio: 0xfdc00000
> Jan 17 11:22:35 LLLx64-32 kernel: PCI: Setting latency timer of device
> 0000:02:00.0 to 64
> Jan 17 11:22:35 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
> /devices/virtual/input/input8
> Jan 17 11:22:35 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
> detected at i2c-2/2-006b/ir0 [cx23885[0]]
> Jan 17 11:22:36 LLLx64-32 kernel: xc5000: waiting for firmware upload
> (dvb-fe-xc5000-1.6.114.fw)...
> Jan 17 11:22:36 LLLx64-32 kernel: firmware: requesting
> dvb-fe-xc5000-1.6.114.fw
> Jan 17 11:22:36 LLLx64-32 kernel: xc5000: firmware read 12401 bytes.
> Jan 17 11:22:36 LLLx64-32 kernel: xc5000: firmware uploading...
> Jan 17 11:22:37 LLLx64-32 kernel: xc5000: firmware upload complete...
> Jan 17 11:22:37 LLLx64-32 kernel: xc5000: waiting for firmware upload
> (dvb-fe-xc5000-1.6.114.fw)...
> Jan 17 11:22:37 LLLx64-32 kernel: firmware: requesting
> dvb-fe-xc5000-1.6.114.fw
> Jan 17 11:22:37 LLLx64-32 kernel: xc5000: firmware read 12401 bytes.
> Jan 17 11:22:37 LLLx64-32 kernel: xc5000: firmware uploading...
> Jan 17 11:22:39 LLLx64-32 kernel: xc5000: firmware upload complete...
> ------------------
>
> And what it does now:
> Jan 23 17:10:47 LLLx64-32 kernel: Linux video capture interface: v2.00
> Jan 23 17:10:47 LLLx64-32 kernel: cx23885 driver version 0.0.2 loaded
> Jan 23 17:10:47 LLLx64-32 kernel: cx23885 0000:02:00.0: PCI INT A ->
> Link[APC7] -> GSI 16 (level, low) -> IRQ 16
> Jan 23 17:10:47 LLLx64-32 kernel: CORE cx23885[0]: subsystem: 18ac:d618,
> board: DViCO FusionHDTV7 Dual Express [card=10,autodetected]
> Jan 23 17:10:47 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
> frontend(s)
> Jan 23 17:10:47 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
> Jan 23 17:10:47 LLLx64-32 kernel: xc5000 1-0064: creating new instance
> Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Successfully identified at
> address 0x64
> Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Firmware has not been loaded
> previously
> Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
> Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering adapter 0 frontend 0
> (Samsung S5H1411 QAM/8VSB Frontend)...
> Jan 23 17:10:47 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
> frontend(s)
> Jan 23 17:10:47 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
> Jan 23 17:10:47 LLLx64-32 kernel: xc5000 2-0064: creating new instance
> Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Successfully identified at
> address 0x64
> Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Firmware has not been loaded
> previously
> Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
> Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering adapter 1 frontend 0
> (Samsung S5H1411 QAM/8VSB Frontend)...
> Jan 23 17:10:47 LLLx64-32 kernel: cx23885_dev_checkrevision() Hardware
> revision = 0xb0
> Jan 23 17:10:47 LLLx64-32 kernel: cx23885[0]/0: found at 0000:02:00.0,
> rev: 2, irq: 16, latency: 0, mmio: 0xfdc00000
> Jan 23 17:10:47 LLLx64-32 kernel: cx23885 0000:02:00.0: setting latency
> timer to 64
> Jan 23 17:10:47 LLLx64-32 kernel: IRQ 16/cx23885[0]: IRQF_DISABLED is
> not guaranteed on shared IRQs
>
> I put a zip of some logs at: http://24.255.17.209:2400/vdr-logs/logs.zip
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
Any progress on this one?
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Lost remote after kernel/v4l update cx23885 chipset
2010-02-01 19:03 ` Timothy D. Lenz
@ 2010-02-02 12:23 ` Andy Walls
0 siblings, 0 replies; 5+ messages in thread
From: Andy Walls @ 2010-02-02 12:23 UTC (permalink / raw)
To: Timothy D. Lenz; +Cc: linux-media
On Mon, 2010-02-01 at 12:03 -0700, Timothy D. Lenz wrote:
>
> On 1/24/2010 1:07 PM, Timothy D. Lenz wrote:
> > After updating from kernel 2.6.26.8 to 2.6.32.2 and from v4l of
> > 05/19/2009 to 01/18/2010 I lost remote function with Dvico FusionHDTV7
> > Dual Express. The driver is loading, but not creating an IR device. Went
> > over it with awalls on IRC. The log is at: http://pastebin.com/m4b02ff0c
> >
> >
> > I noticed that in the kern.log there where 2 different ways ir-kbd-i2c
> > showed up. ir-kbd-i2c no longer shows up when loading drivers.
> >
> > Jan 17 14:59:32 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
> > /devices/virtual/input/input5
> > Jan 17 14:59:32 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
> > detected at i2c-2/2-006b/ir0 [cx23885[0]]
> > ------------------
> > Jan 18 17:23:27 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
> > /devices/virtual/input/input5
> > Jan 18 17:23:27 LLLx64-32 kernel: Creating IR device irrcv0
> > Jan 18 17:23:27 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
> > detected at i2c-1/1-006b/ir0 [cx23885[0]]
> >
> > Jan 18 18:28:50 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
> > /devices/virtual/input/input5
> > Jan 18 18:28:50 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
> > detected at i2c-2/2-006b/ir0 [cx23885[0]]
> >
> > ------------------
> > A driver load that worked:
> >
> > Jan 17 11:22:35 LLLx64-32 kernel: Linux video capture interface: v2.00
> > Jan 17 11:22:35 LLLx64-32 kernel: cx23885 driver version 0.0.2 loaded
> > Jan 17 11:22:35 LLLx64-32 kernel: ACPI: PCI Interrupt 0000:02:00.0[A] ->
> > Link [APC7] -> GSI 16 (level, low) -> IRQ 16
> > Jan 17 11:22:35 LLLx64-32 kernel: CORE cx23885[0]: subsystem: 18ac:d618,
> > board: DViCO FusionHDTV7 Dual Express [card=10,autodetected]
> > Jan 17 11:22:35 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
> > frontend(s)
> > Jan 17 11:22:35 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
> > Jan 17 11:22:35 LLLx64-32 kernel: xc5000 2-0064: creating new instance
> > Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Successfully identified at
> > address 0x64
> > Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Firmware has not been loaded
> > previously
> > Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
> > Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering adapter 0 frontend 0
> > (Samsung S5H1411 QAM/8VSB Frontend)...
> > Jan 17 11:22:35 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
> > frontend(s)
> > Jan 17 11:22:35 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
> > Jan 17 11:22:35 LLLx64-32 kernel: xc5000 3-0064: creating new instance
> > Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Successfully identified at
> > address 0x64
> > Jan 17 11:22:35 LLLx64-32 kernel: xc5000: Firmware has not been loaded
> > previously
> > Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
> > Jan 17 11:22:35 LLLx64-32 kernel: DVB: registering adapter 1 frontend 0
> > (Samsung S5H1411 QAM/8VSB Frontend)...
> > Jan 17 11:22:35 LLLx64-32 kernel: cx23885_dev_checkrevision() Hardware
> > revision = 0xb0
> > Jan 17 11:22:35 LLLx64-32 kernel: cx23885[0]/0: found at 0000:02:00.0,
> > rev: 2, irq: 16, latency: 0, mmio: 0xfdc00000
> > Jan 17 11:22:35 LLLx64-32 kernel: PCI: Setting latency timer of device
> > 0000:02:00.0 to 64
> > Jan 17 11:22:35 LLLx64-32 kernel: input: i2c IR (FusionHDTV) as
> > /devices/virtual/input/input8
> > Jan 17 11:22:35 LLLx64-32 kernel: ir-kbd-i2c: i2c IR (FusionHDTV)
> > detected at i2c-2/2-006b/ir0 [cx23885[0]]
> > Jan 17 11:22:36 LLLx64-32 kernel: xc5000: waiting for firmware upload
> > (dvb-fe-xc5000-1.6.114.fw)...
> > Jan 17 11:22:36 LLLx64-32 kernel: firmware: requesting
> > dvb-fe-xc5000-1.6.114.fw
> > Jan 17 11:22:36 LLLx64-32 kernel: xc5000: firmware read 12401 bytes.
> > Jan 17 11:22:36 LLLx64-32 kernel: xc5000: firmware uploading...
> > Jan 17 11:22:37 LLLx64-32 kernel: xc5000: firmware upload complete...
> > Jan 17 11:22:37 LLLx64-32 kernel: xc5000: waiting for firmware upload
> > (dvb-fe-xc5000-1.6.114.fw)...
> > Jan 17 11:22:37 LLLx64-32 kernel: firmware: requesting
> > dvb-fe-xc5000-1.6.114.fw
> > Jan 17 11:22:37 LLLx64-32 kernel: xc5000: firmware read 12401 bytes.
> > Jan 17 11:22:37 LLLx64-32 kernel: xc5000: firmware uploading...
> > Jan 17 11:22:39 LLLx64-32 kernel: xc5000: firmware upload complete...
> > ------------------
> >
> > And what it does now:
> > Jan 23 17:10:47 LLLx64-32 kernel: Linux video capture interface: v2.00
> > Jan 23 17:10:47 LLLx64-32 kernel: cx23885 driver version 0.0.2 loaded
> > Jan 23 17:10:47 LLLx64-32 kernel: cx23885 0000:02:00.0: PCI INT A ->
> > Link[APC7] -> GSI 16 (level, low) -> IRQ 16
> > Jan 23 17:10:47 LLLx64-32 kernel: CORE cx23885[0]: subsystem: 18ac:d618,
> > board: DViCO FusionHDTV7 Dual Express [card=10,autodetected]
> > Jan 23 17:10:47 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
> > frontend(s)
> > Jan 23 17:10:47 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
> > Jan 23 17:10:47 LLLx64-32 kernel: xc5000 1-0064: creating new instance
> > Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Successfully identified at
> > address 0x64
> > Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Firmware has not been loaded
> > previously
> > Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
> > Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering adapter 0 frontend 0
> > (Samsung S5H1411 QAM/8VSB Frontend)...
> > Jan 23 17:10:47 LLLx64-32 kernel: cx23885_dvb_register() allocating 1
> > frontend(s)
> > Jan 23 17:10:47 LLLx64-32 kernel: cx23885[0]: cx23885 based dvb card
> > Jan 23 17:10:47 LLLx64-32 kernel: xc5000 2-0064: creating new instance
> > Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Successfully identified at
> > address 0x64
> > Jan 23 17:10:47 LLLx64-32 kernel: xc5000: Firmware has not been loaded
> > previously
> > Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering new adapter (cx23885[0])
> > Jan 23 17:10:47 LLLx64-32 kernel: DVB: registering adapter 1 frontend 0
> > (Samsung S5H1411 QAM/8VSB Frontend)...
> > Jan 23 17:10:47 LLLx64-32 kernel: cx23885_dev_checkrevision() Hardware
> > revision = 0xb0
> > Jan 23 17:10:47 LLLx64-32 kernel: cx23885[0]/0: found at 0000:02:00.0,
> > rev: 2, irq: 16, latency: 0, mmio: 0xfdc00000
> > Jan 23 17:10:47 LLLx64-32 kernel: cx23885 0000:02:00.0: setting latency
> > timer to 64
> > Jan 23 17:10:47 LLLx64-32 kernel: IRQ 16/cx23885[0]: IRQF_DISABLED is
> > not guaranteed on shared IRQs
> >
> > I put a zip of some logs at: http://24.255.17.209:2400/vdr-logs/logs.zip
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-media" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
> >
>
> Any progress on this one?
Nope. Maybe around Friday I'll provide a patch with some printk()'s for
debugging as I don't have the hardware. (Unless of course I'm shoveling
snow again...)
Regards,
Andy
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Lost remote after kernel/v4l update cx23885 chipset
@ 2010-02-14 21:50 Mark Zimmerman
2010-12-18 22:51 ` Mark Zimmerman
0 siblings, 1 reply; 5+ messages in thread
From: Mark Zimmerman @ 2010-02-14 21:50 UTC (permalink / raw)
To: linux-media
Greetings:
I found this <http://www.spinics.net/lists/linux-media/msg15421.html>
in the archives and I am having the exact same problem. Everything
worked in 2.6.31. Let me know if there is any testing I could do to
help solve this.
-- Mark
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2010-12-18 22:51 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-01-24 20:07 Lost remote after kernel/v4l update cx23885 chipset Timothy D. Lenz
2010-02-01 19:03 ` Timothy D. Lenz
2010-02-02 12:23 ` Andy Walls
-- strict thread matches above, loose matches on Subject: below --
2010-02-14 21:50 Mark Zimmerman
2010-12-18 22:51 ` Mark Zimmerman
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox