From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from mx1.redhat.com (ext-mx10.extmail.prod.ext.phx2.redhat.com [10.5.110.14]) by int-mx02.intmail.prod.int.phx2.redhat.com (8.13.8/8.13.8) with ESMTP id o7K0sYI9024542 for ; Thu, 19 Aug 2010 20:54:34 -0400 Received: from smtp.nexicom.net (dell.nexicom.net [216.168.96.13]) by mx1.redhat.com (8.13.8/8.13.8) with ESMTP id o7K0sL0U000354 for ; Thu, 19 Aug 2010 20:54:21 -0400 Received: from mail.lockie.ca (dyn-dsl-mb-66-79-239-161.nexicom.net [66.79.239.161]) by smtp.nexicom.net (8.13.6/8.13.4) with ESMTP id o7K0sKiK031204 for ; Thu, 19 Aug 2010 20:54:20 -0400 Received: from [127.0.0.1] (localhost [127.0.0.1]) by mail.lockie.ca (Postfix) with ESMTP id 940AA9831D for ; Thu, 19 Aug 2010 20:54:19 -0400 (EDT) Message-ID: <4C6DD23B.1030404@lockie.ca> Date: Thu, 19 Aug 2010 20:54:19 -0400 From: James MIME-Version: 1.0 To: Video 4 Linux Mailing List Subject: Re: upgraded software and audio stopped working References: <4C630CEE.7000200@lockie.ca> In-Reply-To: <4C630CEE.7000200@lockie.ca> List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Errors-To: video4linux-list-bounces@redhat.com Sender: Mauro Carvalho Chehab List-ID: On 08/11/10 16:49, James wrote: > It could just be coincidental that the audio stopped working after I > upgrade software. > I didn't try it right after I upgraded the system software so it could > be the hardware just failed. > I can still tune channels, I just don't get audio. > > bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] > bttv0: Hauppauge eeprom indicates model#44981 > bttv0: tuner type=50 > bttv0: audio absent, no audio device found! > tuner 2-0061: chip found @ 0xc2 (bt878 #0 [sw]) I upgraded the kernel and the audio out works. bttv: driver version 0.9.18 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv 0000:02:08.0: PCI INT A -> Link[LNKA] -> GSI 17 (level, low) -> IRQ 17 bttv0: Bt878 (rev 17) at 0000:02:08.0, irq: 17, latency: 32, mmio: 0xcffff000 bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb bttv0: using: Hauppauge (bt878) [card=10,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] bttv0: Hauppauge eeprom indicates model#44981 bttv0: tuner type=50 bttv0: audio absent, no audio device found! tuner 2-0061: chip found @ 0xc2 (bt878 #0 [sw]) bttv0: registered device video0 bttv0: registered device vbi0 bttv0: PLL: 28636363 => 35468950 .. ok bttv0: PLL can sleep, using XTAL (28636363). -- video4linux-list mailing list Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe https://www.redhat.com/mailman/listinfo/video4linux-list