From: thomas schorpp <thomas.schorpp@googlemail.com>
To: linux-media@vger.kernel.org
Subject: dvb-c: TT C-1501: tda827x.c: Cannot hold lock at 746 MHz
Date: Sat, 02 Oct 2010 16:43:21 +0200 [thread overview]
Message-ID: <4CA74509.6000404@gmail.com> (raw)
Hello,
Klaas patch is not complete:
http://article.gmane.org/gmane.linux.drivers.dvb/47571
I found a hole at 746MHz with 2.6.34.0 kernel and DE provider kabelbw.de,
Picture fragments and audio bursts only:
Oct 2 15:53:03 tom1 vdr: [16380] receiver on device 1 thread ended (pid=16268, tid=16380)
Oct 2 15:53:03 tom1 kernel: tda827x: tda827xa_set_params:
Oct 2 15:53:03 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
Oct 2 15:53:03 tom1 kernel: tda827x: tda8275a AGC2 gain is: 4
Oct 2 15:53:04 tom1 vdr: [16462] setting audio track to 1 (0)
Oct 2 15:53:04 tom1 kernel: tda827x: tda827xa_set_params:
Oct 2 15:53:04 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
Oct 2 15:53:04 tom1 kernel: tda827x: tda8275a AGC2 gain is: 5
Oct 2 15:53:04 tom1 vdr: [16279] frontend 0 lost lock on channel 496, tp 746
Oct 2 15:53:04 tom1 vdr: [16279] frontend 0 regained lock on channel 496, tp 746
Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params:
Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
Oct 2 15:53:05 tom1 kernel: tda827x: tda8275a AGC2 gain is: 4
Oct 2 15:53:05 tom1 vdr: [16279] frontend 0 lost lock on channel 496, tp 746
Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params:
Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
Oct 2 15:53:05 tom1 kernel: tda827x: tda8275a AGC2 gain is: 4
Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params:
Oct 2 15:53:05 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
Oct 2 15:53:05 tom1 kernel: tda827x: tda8275a AGC2 gain is: 5
Oct 2 15:53:06 tom1 vdr: [16279] frontend 0 regained lock on channel 496, tp 746
Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params:
Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
Oct 2 15:53:06 tom1 kernel: tda827x: tda8275a AGC2 gain is: 5
Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params:
Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
Oct 2 15:53:06 tom1 kernel: tda827x: tda8275a AGC2 gain is: 5
Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params:
Oct 2 15:53:06 tom1 kernel: tda827x: tda827xa_set_params select tda827xa_dvbc
Oct 2 15:53:06 tom1 kernel: tda827x: tda8275a AGC2 gain is: 4
Oct 2 15:53:06 tom1 vdr: [16268] switching to channel 494
cycle: 78 d_time: 0.004 s Sig: 51657 SNR: 43690 BER: 1728 UBLK: 55 Stat: 0x00 []
cycle: 79 d_time: 0.004 s Sig: 52428 SNR: 60395 BER: 1728 UBLK: 57 Stat: 0x03 [SIG CARR ]
cycle: 80 d_time: 0.004 s Sig: 50886 SNR: 46517 BER: 1728 UBLK: 95 Stat: 0x00 []
cycle: 81 d_time: 0.007 s Sig: 52428 SNR: 44461 BER: 1728 UBLK: 54 Stat: 0x03 [SIG CARR ]
cycle: 82 d_time: 0.003 s Sig: 51657 SNR: 61423 BER: 1728 UBLK: 5 Stat: 0x1f [SIG CARR VIT SYNC LOCK ]
cycle: 83 d_time: 0.237 s Sig: 40092 SNR: 47288 BER: 1048575 UBLK: 66 Stat: 0x00 []
cycle: 84 d_time: 0.005 s Sig: 56283 SNR: 45232 BER: 1728 UBLK: 113 Stat: 0x00 []
cycle: 85 d_time: 0.006 s Sig: 53199 SNR: 46774 BER: 1728 UBLK: 136 Stat: 0x00 []
cycle: 86 d_time: 0.008 s Sig: 50115 SNR: 44975 BER: 1728 UBLK: 55 Stat: 0x00 []
cycle: 87 d_time: 0.004 s Sig: 53199 SNR: 53970 BER: 1728 UBLK: 287 Stat: 0x1f [SIG CARR VIT SYNC LOCK ]
cycle: 88 d_time: 0.020 s Sig: 50886 SNR: 61166 BER: 1728 UBLK: 62 Stat: 0x03 [SIG CARR ]
Current parameters:
Frequency: 746000.000 kHz
Inversion: ON
Symbol rate: 6.900000 MSym/s
FEC: none
Modulation: QAM 64
Card is just bought newly:
00:06.0 0480: 1131:7146 (rev 01)
Subsystem: 13c2:101a
Flags: bus master, medium devsel, latency 32, IRQ 17
Memory at fbeffc00 (32-bit, non-prefetchable) [size=512]
Kernel driver in use: budget_ci dvb
Other (tested favourite) channels are tuned in fine.
No network problems for this transponder reported in cable provider's support forums.
Anyone got the chips datasheet or a hint what to tweak in the tda827xa_dvbc[] for this frequency?
{ .lomax = 802000000, .svco = 2, .spd = 0, .scr = 2, .sbs = 4, .gc3 = 1}, ?
thx,
Y
tom
next reply other threads:[~2010-10-02 14:43 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-10-02 14:43 thomas schorpp [this message]
2010-10-02 15:19 ` dvb-c: TT C-1501: tda827x.c: Cannot hold lock at 746 MHz thomas schorpp
2010-10-02 16:54 ` thomas schorpp
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4CA74509.6000404@gmail.com \
--to=thomas.schorpp@googlemail.com \
--cc=linux-media@vger.kernel.org \
--cc=thomas.schorpp@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox