* AF9015 problems
@ 2011-03-20 19:10 Lucio Crusca
2011-03-20 19:37 ` Antti Palosaari
0 siblings, 1 reply; 3+ messages in thread
From: Lucio Crusca @ 2011-03-20 19:10 UTC (permalink / raw)
To: linux-media
Hello *,
I'm new here, hope to be on the right list (crossposting from
linux-dvb@linuxtv.org which mailman told me is deprecated).
I'm trying to tune a AF9015, but w_scan finds only 4 tv services, while the
same dongle attached to the same antenna cable, on the same computer, with
Windows Media Center finds as much as 135 tv services.
The 4 services it finds are all from the same 205500 KHz transponder. Any clue?
Some details:
# lsusb
...
Bus 002 Device 002: ID 15a4:9016 Afatech Technologies, Inc. AF9015 DVB-T
USB2.0 stick
...
# dmesg
[ 6484.732102] usb 2-2: new high speed USB device using ehci_hcd and address 2
[ 6484.913877] IR NEC protocol handler initialized
[ 6484.915782] IR RC5(x) protocol handler initialized
[ 6484.918307] IR RC6 protocol handler initialized
[ 6484.920723] IR JVC protocol handler initialized
[ 6484.922643] IR Sony protocol handler initialized
[ 6484.925543] lirc_dev: IR Remote Control driver registered, major 250
[ 6484.926765] IR LIRC bridge handler initialized
[ 6485.285760] dvb-usb: found a 'Afatech AF9015 DVB-T USB2.0 stick' in cold
state, will try to load a firmware
[ 6485.318245] dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw'
[ 6485.385897] dvb-usb: found a 'Afatech AF9015 DVB-T USB2.0 stick' in warm
state.
[ 6485.386035] dvb-usb: will pass the complete MPEG2 transport stream to the
software demuxer.
[ 6485.386449] DVB: registering new adapter (Afatech AF9015 DVB-T USB2.0
stick)
[ 6485.404493] af9013: firmware version:4.95.0.0
[ 6485.408621] DVB: registering adapter 0 frontend 0 (Afatech AF9013 DVB-T)...
[ 6485.413124] tda18218: NXP TDA18218HN successfully identified.
[ 6485.415018] Registered IR keymap rc-empty
[ 6485.415127] input: IR-receiver inside an USB DVB receiver as
/devices/pci0000:00/0000:00:1d.7/usb2/2-2/rc/rc0/input13
[ 6485.415208] rc0: IR-receiver inside an USB DVB receiver as
/devices/pci0000:00/0000:00:1d.7/usb2/2-2/rc/rc0
[ 6485.415212] dvb-usb: schedule remote query interval to 500 msecs.
[ 6485.415216] dvb-usb: Afatech AF9015 DVB-T USB2.0 stick successfully
initialized and connected.
[ 6485.423782] usbcore: registered new interface driver dvb_usb_af9015
[ 6485.440130] usbcore: registered new interface driver usbhid
[ 6485.440134] usbhid: USB HID core driver
# uname -r
2.6.38-rc6
# lsmod | grep dvb
dvb_usb_af9015 19468 0
dvb_usb 15052 1 dvb_usb_af9015
dvb_core 86023 1 dvb_usb
rc_core 16999 9
ir_lirc_codec,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,dvb_usb_af9015,ir_rc5_decoder,ir_nec_decoder,dvb_usb
# w_scan -c IT -ft -X
w_scan version 20100316 (compiled for DVB API 5.1)
using settings for ITALY
DVB aerial
DVB-T Europe
frontend_type DVB-T, channellist 4
output format czap/tzap/szap/xine
Info: using DVB adapter auto detection.
/dev/dvb/adapter0/frontend0 -> DVB-T "Afatech AF9013 DVB-T": good :-)
Using DVB-T frontend (adapter /dev/dvb/adapter0/frontend0)
-_-_-_-_ Getting frontend capabilities-_-_-_-_
Using DVB API 5.2
frontend Afatech AF9013 DVB-T supports
INVERSION_AUTO
QAM_AUTO
TRANSMISSION_MODE_AUTO
GUARD_INTERVAL_AUTO
HIERARCHY_AUTO
FEC_AUTO
-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_
Scanning 7MHz frequencies...
177500: (time: 00:00)
184500: (time: 00:03)
191500: (time: 00:05)
198500: (time: 00:08)
205500: (time: 00:10) (time: 00:13) signal ok:
QAM_AUTO f = 205500 kHz I999B7C999D999T999G999Y999
new transponder:
(QAM_64 f = 1600000 kHz I999B8C34D0T8G16Y0)
212500: (time: 00:26)
219500: (time: 00:29)
226500: (time: 00:31)
Scanning 8MHz frequencies...
474000: (time: 00:34)
482000: (time: 00:36)
490000: (time: 00:39)
498000: (time: 00:41)
506000: (time: 00:44)
514000: (time: 00:46)
522000: (time: 00:49)
530000: (time: 00:51)
538000: (time: 00:54)
546000: (time: 00:56)
554000: (time: 00:59)
562000: (time: 01:01)
570000: (time: 01:04)
578000: (time: 01:07)
586000: (time: 01:09)
594000: (time: 01:12)
602000: (time: 01:14)
610000: (time: 01:17)
618000: (time: 01:19)
626000: (time: 01:22)
634000: (time: 01:24)
642000: (time: 01:27) (time: 01:29)
650000: (time: 01:30)
658000: (time: 01:33)
666000: (time: 01:36)
674000: (time: 01:38)
682000: (time: 01:41)
690000: (time: 01:43)
698000: (time: 01:46)
706000: (time: 01:48)
714000: (time: 01:51)
722000: (time: 01:53)
730000: (time: 01:56)
738000: (time: 01:59)
746000: (time: 02:01)
754000: (time: 02:04)
762000: (time: 02:06)
770000: (time: 02:09)
778000: (time: 02:11)
786000: (time: 02:14)
794000: (time: 02:16)
802000: (time: 02:19)
810000: (time: 02:22)
818000: (time: 02:24)
826000: (time: 02:27)
834000: (time: 02:29)
842000: (time: 02:32)
850000: (time: 02:34)
858000: (time: 02:37)
tune to: QAM_AUTO f = 205500 kHz I999B7C999D999T999G999Y999
(time: 02:39) service = Rai 1 (RAI)
service = Rai 2 (RAI)
service = Rai 3 TGR Piemonte (Rai)
service = Rai Radio1 (RAI)
service = Rai Radio2 (RAI)
service = Rai Radio3 (RAI)
service = Rai News (Rai)
tune to: QAM_64 f = 1600000 kHz I999B8C34D0T8G16Y0
(time: 02:53) set_frontend:1703: ERROR: Setting frontend parameters failed
(API v5.x)
: 22 Invalid argument
tune to: QAM_64 f = 1600000 kHz I999B8C34D0T8G16Y0
(time: 02:53) set_frontend:1703: ERROR: Setting frontend parameters failed
(API v5.x)
: 22 Invalid argument
dumping lists (7 services)
Done.
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: AF9015 problems
2011-03-20 19:10 AF9015 problems Lucio Crusca
@ 2011-03-20 19:37 ` Antti Palosaari
2011-03-20 20:27 ` Lucio Crusca
0 siblings, 1 reply; 3+ messages in thread
From: Antti Palosaari @ 2011-03-20 19:37 UTC (permalink / raw)
To: Lucio Crusca; +Cc: linux-media
On 03/20/2011 09:10 PM, Lucio Crusca wrote:
> I'm trying to tune a AF9015, but w_scan finds only 4 tv services, while the
> same dongle attached to the same antenna cable, on the same computer, with
> Windows Media Center finds as much as 135 tv services.
>
> The 4 services it finds are all from the same 205500 KHz transponder. Any clue?
[...]
> 205500: (time: 00:10) (time: 00:13) signal ok:
> QAM_AUTO f = 205500 kHz I999B7C999D999T999G999Y999
> new transponder:
> (QAM_64 f = 1600000 kHz I999B8C34D0T8G16Y0)
[...]
> tune to: QAM_64 f = 1600000 kHz I999B8C34D0T8G16Y0
> (time: 02:53) set_frontend:1703: ERROR: Setting frontend parameters failed
> (API v5.x)
> : 22 Invalid argument
> tune to: QAM_64 f = 1600000 kHz I999B8C34D0T8G16Y0
> (time: 02:53) set_frontend:1703: ERROR: Setting frontend parameters failed
> (API v5.x)
> : 22 Invalid argument
> dumping lists (7 services)
> Done.
1600000 kHz == 1600 MHz == 1.6 GHz
uh, operator have configured wrongly neighbour transponders ?
I have still no knowledge why scanning didn't find any other freqs. If
there is error in driver then most likely it is TDA18218HN tuner driver
issue since thats reverse-engineered one and without modulator I cannot
ran very much tests.
Could you say which are missing freqs and bandwidth of those freqs?
Antti
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: AF9015 problems
2011-03-20 19:37 ` Antti Palosaari
@ 2011-03-20 20:27 ` Lucio Crusca
0 siblings, 0 replies; 3+ messages in thread
From: Lucio Crusca @ 2011-03-20 20:27 UTC (permalink / raw)
To: Antti Palosaari; +Cc: linux-media
> Could you say which are missing freqs and bandwidth of those freqs?
The missing frequences are all in the 8MHz bands, while the 4 services it finds
are the only services in the 7MHz bands. The 4 services it finds are all "RAI"
services, which is the national tv here, just in case it helps knowing that.
When I scan for services with the TV decoder, RAI services are always the first
to be found and I'm quite convinced that's because they have the lowest
frequencies among all. 205500 KHz seems also to be the last frequency with
7MHz bandwidth. The TV decoder, after RAI services, skips immediately to 8MHz
bands.
The TV decoder finds a number of services at 594000 KHz/8MHz bandwidth
(Mediaset), and then others at higher frequences. Between 205500 and 594000
KHz there appears to be nothing also for the TV decoder.
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2011-03-20 20:27 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-03-20 19:10 AF9015 problems Lucio Crusca
2011-03-20 19:37 ` Antti Palosaari
2011-03-20 20:27 ` Lucio Crusca
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox