* Help needed: Anysee E30C Plus (DVB-C Tuner)
@ 2011-05-12 13:27 Per Kofod
2011-05-12 14:08 ` Antti Palosaari
0 siblings, 1 reply; 4+ messages in thread
From: Per Kofod @ 2011-05-12 13:27 UTC (permalink / raw)
To: linux-media
Hi
I am new to this mailing list, so bare with me if this have been asked
before.
I have just bought an Anysee E30C Plus, as I had read, that this device
is supported
in Linux, my plan is building a Mythtv media center, to replace my old
harddisk recorder.
However I cannot get it to work, and then I read thatt the newest
version might not work,
and that I should join this list.
I have tried to compile a new kernel with the newest dvb stuff from the
git repository, just
to make sure, that I have the newest drivers. I have alsio blacklistet
the zl10353 module
to avoid the device being loaded as an DVB-T device (which it is not, it
is a cable only version).
What information do you need me to obtain, or do you have a hint to how
I might get this working?
The device is reconnized OK as seen here from dmesg:
[ 11.354973] dvb-usb: found a 'Anysee DVB USB2.0' in warm state.
[ 11.355004] dvb-usb: will pass the complete MPEG2 transport stream to
the software demuxer.
[ 11.355239] DVB: registering new adapter (Anysee DVB USB2.0)
[ 11.356661] anysee: firmware version:0.1.2 hardware id:15
[ 11.391192] IR NEC protocol handler initialized
[ 11.412221] IR RC5(x) protocol handler initialized
[ 11.412611] DVB: Unable to find symbol zl10353_attach()
[ 11.414527] DVB: Unable to find symbol zl10353_attach()
[ 11.417536] DVB: registering adapter 1 frontend 0 (Philips TDA10023
DVB-C)...
[ 11.430950] IR RC6 protocol handler initialized
[ 11.553821] IR JVC protocol handler initialized
[ 11.555642] input: IR-receiver inside an USB DVB receiver as
/devices/pci0000:00/0000:00:1d.7/usb2/2-5/input/input6
[ 11.555682] dvb-usb: schedule remote query interval to 200 msecs.
[ 11.555689] dvb-usb: Anysee DVB USB2.0 successfully initialized and
connected.
[ 11.557207] usbcore: registered new interface driver dvb_usb_anysee
[ 11.569445] IR Sony protocol handler initialized
[ 11.584259] lirc_dev: IR Remote Control driver registered, major 251
[ 11.586747] IR LIRC bridge handler initialized
but lsusb reports this as an DVB-T Device:
tux3:~ # lsusb -s 002:002 -v
Bus 002 Device 002: ID 1c73:861f AMT Anysee E30 USB 2.0 DVB-T Receiver
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1c73 AMT
idProduct 0x861f Anysee E30 USB 2.0 DVB-T Receiver
bcdDevice 1.00
iManufacturer 1 AMT.CO.KR
iProduct 2 anysee-FA(LP)
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 83
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x1400 3x 1024 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x1400 3x 1024 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0002
(Bus Powered)
Remote Wakeup Enabled
The problem is, that I cannot get it to tune into any frequency:
using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'
initial transponder 143000000 6875000 0 3
initial transponder 156000000 6875000 0 3
initial transponder 378000000 6875000 0 3
initial transponder 394000000 6875000 0 3
initial transponder 442000000 6875000 0 3
initial transponder 490000000 6875000 0 3
initial transponder 498000000 6875000 0 3
initial transponder 514000000 6875000 0 3
initial transponder 530000000 6875000 0 3
initial transponder 538000000 6875000 0 3
initial transponder 554000000 6875000 0 3
initial transponder 570000000 6875000 0 3
initial transponder 578000000 6875000 0 3
initial transponder 618000000 6875000 0 3
initial transponder 626000000 6875000 0 3
initial transponder 714000000 6875000 0 3
initial transponder 730000000 6875000 0 3
initial transponder 770000000 6875000 0 3
initial transponder 786000000 6875000 0 3
initial transponder 794000000 6875000 0 3
>>> tune to: 143000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_64
WARNING: >>> tuning failed!!!
>>> tune to: 143000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_64 (tuning
failed)
WARNING: >>> tuning failed!!!
>>> tune to: 156000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_64
WARNING: >>> tuning failed!!!
>>> tune to: 156000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_64 (tuning
failed)
WARNING: >>> tuning failed!!!
>>> tune to: 378000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_64
WARNING: >>> tuning failed!!!
ETC
Rgds Per
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Help needed: Anysee E30C Plus (DVB-C Tuner)
2011-05-12 13:27 Help needed: Anysee E30C Plus (DVB-C Tuner) Per Kofod
@ 2011-05-12 14:08 ` Antti Palosaari
2011-05-12 14:35 ` Per Kofod
0 siblings, 1 reply; 4+ messages in thread
From: Antti Palosaari @ 2011-05-12 14:08 UTC (permalink / raw)
To: Per Kofod; +Cc: linux-media
On 05/12/2011 04:27 PM, Per Kofod wrote:
> Hi
>
> I am new to this mailing list, so bare with me if this have been asked
> before.
>
> I have just bought an Anysee E30C Plus, as I had read, that this device
> is supported
> in Linux, my plan is building a Mythtv media center, to replace my old
> harddisk recorder.
>
> However I cannot get it to work, and then I read thatt the newest
> version might not work,
> and that I should join this list.
>
> I have tried to compile a new kernel with the newest dvb stuff from the
> git repository, just
> to make sure, that I have the newest drivers. I have alsio blacklistet
> the zl10353 module
> to avoid the device being loaded as an DVB-T device (which it is not, it
> is a cable only version).
>
> What information do you need me to obtain, or do you have a hint to how
> I might get this working?
>
> The device is reconnized OK as seen here from dmesg:
>
> [ 11.354973] dvb-usb: found a 'Anysee DVB USB2.0' in warm state.
> [ 11.355004] dvb-usb: will pass the complete MPEG2 transport stream to
> the software demuxer.
> [ 11.355239] DVB: registering new adapter (Anysee DVB USB2.0)
> [ 11.356661] anysee: firmware version:0.1.2 hardware id:15
For the some reason hardware ID 15 does not work on latest Ubuntu 11.04.
That is basically E30 Combo Plus and newer E30 C Plus, which is same
device as E30 Combo Plus but without DVB-T demod.
Install latest drivers and it will work. And I hope someone have time to
examine why it does not work anymore out-of-the-box in Ubuntu 11.04.
http://linuxtv.org/wiki/index.php/How_to_Obtain,_Build_and_Install_V4L-DVB_Device_Drivers
Antti
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Help needed: Anysee E30C Plus (DVB-C Tuner)
2011-05-12 14:08 ` Antti Palosaari
@ 2011-05-12 14:35 ` Per Kofod
2011-05-12 17:33 ` Antti Palosaari
0 siblings, 1 reply; 4+ messages in thread
From: Per Kofod @ 2011-05-12 14:35 UTC (permalink / raw)
To: Antti Palosaari; +Cc: linux-media
Thanks, that worked. Actually I am not running ubuntu on this PC; but
OpenSuSE 11.4;
but I was planninh using Mythbuntu far my media center.
Thanks a lot.
Cheers Per
On 05/12/2011 04:08 PM, Antti Palosaari wrote:
> On 05/12/2011 04:27 PM, Per Kofod wrote:
>> Hi
>>
>> I am new to this mailing list, so bare with me if this have been asked
>> before.
>>
>> I have just bought an Anysee E30C Plus, as I had read, that this device
>> is supported
>> in Linux, my plan is building a Mythtv media center, to replace my old
>> harddisk recorder.
>>
>> However I cannot get it to work, and then I read thatt the newest
>> version might not work,
>> and that I should join this list.
>>
>> I have tried to compile a new kernel with the newest dvb stuff from the
>> git repository, just
>> to make sure, that I have the newest drivers. I have alsio blacklistet
>> the zl10353 module
>> to avoid the device being loaded as an DVB-T device (which it is not, it
>> is a cable only version).
>>
>> What information do you need me to obtain, or do you have a hint to how
>> I might get this working?
>>
>> The device is reconnized OK as seen here from dmesg:
>>
>> [ 11.354973] dvb-usb: found a 'Anysee DVB USB2.0' in warm state.
>> [ 11.355004] dvb-usb: will pass the complete MPEG2 transport stream to
>> the software demuxer.
>> [ 11.355239] DVB: registering new adapter (Anysee DVB USB2.0)
>> [ 11.356661] anysee: firmware version:0.1.2 hardware id:15
>
>
> For the some reason hardware ID 15 does not work on latest Ubuntu
> 11.04. That is basically E30 Combo Plus and newer E30 C Plus, which is
> same device as E30 Combo Plus but without DVB-T demod.
>
> Install latest drivers and it will work. And I hope someone have time
> to examine why it does not work anymore out-of-the-box in Ubuntu 11.04.
>
> http://linuxtv.org/wiki/index.php/How_to_Obtain,_Build_and_Install_V4L-DVB_Device_Drivers
>
>
>
> Antti
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Help needed: Anysee E30C Plus (DVB-C Tuner)
2011-05-12 14:35 ` Per Kofod
@ 2011-05-12 17:33 ` Antti Palosaari
0 siblings, 0 replies; 4+ messages in thread
From: Antti Palosaari @ 2011-05-12 17:33 UTC (permalink / raw)
To: Per Kofod; +Cc: linux-media
Thanks for the report. I have now following matrix:
not working:
OpenSuSE 11.4 Kernel 2.6.37
Ubuntu 11.4 Kernel 2.6.38
working:
Fedora 14 Kernel 2.6.35
regards
Antti
On 05/12/2011 05:35 PM, Per Kofod wrote:
> Thanks, that worked. Actually I am not running ubuntu on this PC; but
> OpenSuSE 11.4;
> but I was planninh using Mythbuntu far my media center.
>
> Thanks a lot.
>
> Cheers Per
>
> On 05/12/2011 04:08 PM, Antti Palosaari wrote:
>> On 05/12/2011 04:27 PM, Per Kofod wrote:
>>> Hi
>>>
>>> I am new to this mailing list, so bare with me if this have been asked
>>> before.
>>>
>>> I have just bought an Anysee E30C Plus, as I had read, that this device
>>> is supported
>>> in Linux, my plan is building a Mythtv media center, to replace my old
>>> harddisk recorder.
>>>
>>> However I cannot get it to work, and then I read thatt the newest
>>> version might not work,
>>> and that I should join this list.
>>>
>>> I have tried to compile a new kernel with the newest dvb stuff from the
>>> git repository, just
>>> to make sure, that I have the newest drivers. I have alsio blacklistet
>>> the zl10353 module
>>> to avoid the device being loaded as an DVB-T device (which it is not, it
>>> is a cable only version).
>>>
>>> What information do you need me to obtain, or do you have a hint to how
>>> I might get this working?
>>>
>>> The device is reconnized OK as seen here from dmesg:
>>>
>>> [ 11.354973] dvb-usb: found a 'Anysee DVB USB2.0' in warm state.
>>> [ 11.355004] dvb-usb: will pass the complete MPEG2 transport stream to
>>> the software demuxer.
>>> [ 11.355239] DVB: registering new adapter (Anysee DVB USB2.0)
>>> [ 11.356661] anysee: firmware version:0.1.2 hardware id:15
>>
>>
>> For the some reason hardware ID 15 does not work on latest Ubuntu
>> 11.04. That is basically E30 Combo Plus and newer E30 C Plus, which is
>> same device as E30 Combo Plus but without DVB-T demod.
>>
>> Install latest drivers and it will work. And I hope someone have time
>> to examine why it does not work anymore out-of-the-box in Ubuntu 11.04.
>>
>> http://linuxtv.org/wiki/index.php/How_to_Obtain,_Build_and_Install_V4L-DVB_Device_Drivers
>>
>>
>>
>> Antti
>>
>
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2011-05-12 17:33 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-05-12 13:27 Help needed: Anysee E30C Plus (DVB-C Tuner) Per Kofod
2011-05-12 14:08 ` Antti Palosaari
2011-05-12 14:35 ` Per Kofod
2011-05-12 17:33 ` Antti Palosaari
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox