xc4000 patches folded

[Mauro Carvalho Chehab <mchehab@redhat.com>]

In order to make easier for review, I've folded all the following xc4000 patches into one
patch:

Davide Ferri (1):
      [media] dib0700: add initial code for PCTV 340e by Davide Ferri

Devin Heitmueller (22):
      [media] dib0700: add USB id for PCTV 340eSE
      [media] dib0700: properly setup GPIOs for PCTV 340e
      [media] dib0700: successfully connect to xc4000 over i2c for PCTV 340e
      [media] dib0700: add a sleep before attempting to detect dib7000p
      [media] dib7000p: setup dev.parent for i2c master built into 7000p
      [media] xc4000: pull in firmware management code from xc3028
      [media] xc4000: cut over to using xc5000 version for loading i2c sequences
      [media] xc4000: properly set type for init1 firmware
      [media] xc4000: remove XREG_BUSY code only supported in xc5000
      [media] xc4000: remove xc5000 firmware loading routine
      [media] xc4000: add code to do standard and scode firmware loading
      [media] xc4000: continued cleanup of the firmware loading routine
      [media] xc4000: use if_khz provided in xc4000_config
      [media] xc4000: setup dib7000p AGC config for PCTV 340e
      [media] xc4000: handle dib0700 broken i2c stretching
      [media] dib0700: fixup PLL config for PCTV 340e
      [media] xc4000: get rid of hard-coded 8MHz firmware config
      [media] dib0700: make PCTV 340e work!
      [media] xc4000: turn off debug logging by default
      [media] xc4000: rename firmware image filename
      [media] xc4000: cleanup dmesg logging
      [media] dib0700: remove notes from bringup of PCTV 340e

Istvan Varga (19):
      [media] XC4000: code cleanup
      [media] XC4000: updated standards table
      [media] XC4000: added support for 7 MHz DVB-T
      [media] XC4000: added mutex
      [media] XC4000: fixed frequency error
      [media] XC4000: added firmware_name parameter
      [media] XC4000: simplified seek_firmware()
      [media] XC4000: simplified load_scode
      [media] XC4000: check_firmware() cleanup
      [media] XC4000: added card_type
      [media] XC4000: implemented power management
      [media] XC4000: firmware initialization
      [media] XC4000: debug message improvements
      [media] XC4000: setting registers
      [media] XC4000: added audio_std module parameter
      [media] XC4000: implemented analog TV and radio
      [media] XC4000: xc_tune_channel() cleanup
      [media] XC4000: removed redundant tuner reset
      [media] XC4000: detect XC4100

Mauro Carvalho Chehab (1):
      [media] xc4000: Fix a few bad whitespaces on it

 Documentation/video4linux/CARDLIST.tuner    |    1 +
 drivers/media/common/tuners/Kconfig         |   10 +
 drivers/media/common/tuners/Makefile        |    1 +
 drivers/media/common/tuners/tuner-types.c   |    4 +
 drivers/media/common/tuners/xc4000.c        | 1731 +++++++++++++++++++++++++++
 drivers/media/common/tuners/xc4000.h        |   66 +
 drivers/media/dvb/dvb-usb/dib0700_devices.c |  185 +++
 drivers/media/dvb/dvb-usb/dvb-usb-ids.h     |    2 +
 drivers/media/dvb/frontends/dib7000p.c      |    5 +
 drivers/media/video/tuner-core.c            |   14 +
 include/media/tuner.h                       |    2 +
 11 files changed, 2021 insertions(+), 0 deletions(-)
 create mode 100644 drivers/media/common/tuners/xc4000.c
 create mode 100644 drivers/media/common/tuners/xc4000.h

I'll be replying to this email for the xc4000 driver review.

Cheers,
Mauro.

diff --git a/Documentation/video4linux/CARDLIST.tuner b/Documentation/video4linux/CARDLIST.tuner
index 562d7fa..6323b7a 100644
--- a/Documentation/video4linux/CARDLIST.tuner
+++ b/Documentation/video4linux/CARDLIST.tuner
@@ -78,6 +78,7 @@ tuner=77 - TCL tuner MF02GIP-5N-E
 tuner=78 - Philips FMD1216MEX MK3 Hybrid Tuner
 tuner=79 - Philips PAL/SECAM multi (FM1216 MK5)
 tuner=80 - Philips FQ1216LME MK3 PAL/SECAM w/active loopthrough
+tuner=81 - Xceive 4000 tuner
 tuner=81 - Partsnic (Daewoo) PTI-5NF05
 tuner=82 - Philips CU1216L
 tuner=83 - NXP TDA18271
diff --git a/drivers/media/common/tuners/Kconfig b/drivers/media/common/tuners/Kconfig
index 22d3ca3..996302a 100644
--- a/drivers/media/common/tuners/Kconfig
+++ b/drivers/media/common/tuners/Kconfig
@@ -23,6 +23,7 @@ config MEDIA_TUNER
 	depends on VIDEO_MEDIA && I2C
 	select MEDIA_TUNER_XC2028 if !MEDIA_TUNER_CUSTOMISE
 	select MEDIA_TUNER_XC5000 if !MEDIA_TUNER_CUSTOMISE
+	select MEDIA_TUNER_XC4000 if !MEDIA_TUNER_CUSTOMISE
 	select MEDIA_TUNER_MT20XX if !MEDIA_TUNER_CUSTOMISE
 	select MEDIA_TUNER_TDA8290 if !MEDIA_TUNER_CUSTOMISE
 	select MEDIA_TUNER_TEA5761 if !MEDIA_TUNER_CUSTOMISE
@@ -152,6 +153,15 @@ config MEDIA_TUNER_XC5000
 	  This device is only used inside a SiP called together with a
 	  demodulator for now.
 
+config MEDIA_TUNER_XC4000
+	tristate "Xceive XC4000 silicon tuner"
+	depends on VIDEO_MEDIA && I2C
+	default m if MEDIA_TUNER_CUSTOMISE
+	help
+	  A driver for the silicon tuner XC4000 from Xceive.
+	  This device is only used inside a SiP called together with a
+	  demodulator for now.
+
 config MEDIA_TUNER_MXL5005S
 	tristate "MaxLinear MSL5005S silicon tuner"
 	depends on VIDEO_MEDIA && I2C
diff --git a/drivers/media/common/tuners/Makefile b/drivers/media/common/tuners/Makefile
index 2cb4f53..20d24fc 100644
--- a/drivers/media/common/tuners/Makefile
+++ b/drivers/media/common/tuners/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_MEDIA_TUNER_TDA9887) += tda9887.o
 obj-$(CONFIG_MEDIA_TUNER_TDA827X) += tda827x.o
 obj-$(CONFIG_MEDIA_TUNER_TDA18271) += tda18271.o
 obj-$(CONFIG_MEDIA_TUNER_XC5000) += xc5000.o
+obj-$(CONFIG_MEDIA_TUNER_XC4000) += xc4000.o
 obj-$(CONFIG_MEDIA_TUNER_MT2060) += mt2060.o
 obj-$(CONFIG_MEDIA_TUNER_MT2266) += mt2266.o
 obj-$(CONFIG_MEDIA_TUNER_QT1010) += qt1010.o
diff --git a/drivers/media/common/tuners/tuner-types.c b/drivers/media/common/tuners/tuner-types.c
index afba6dc..94a603a 100644
--- a/drivers/media/common/tuners/tuner-types.c
+++ b/drivers/media/common/tuners/tuner-types.c
@@ -1805,6 +1805,10 @@ struct tunertype tuners[] = {
 		.name   = "Xceive 5000 tuner",
 		/* see xc5000.c for details */
 	},
+	[TUNER_XC4000] = { /* Xceive 4000 */
+		.name   = "Xceive 4000 tuner",
+		/* see xc4000.c for details */
+	},
 	[TUNER_TCL_MF02GIP_5N] = { /* TCL tuner MF02GIP-5N-E */
 		.name   = "TCL tuner MF02GIP-5N-E",
 		.params = tuner_tcl_mf02gip_5n_params,
diff --git a/drivers/media/common/tuners/xc4000.c b/drivers/media/common/tuners/xc4000.c
new file mode 100644
index 0000000..160ca26
--- /dev/null
+++ b/drivers/media/common/tuners/xc4000.c
@@ -0,0 +1,1731 @@
+/*
+ *  Driver for Xceive XC4000 "QAM/8VSB single chip tuner"
+ *
+ *  Copyright (c) 2007 Xceive Corporation
+ *  Copyright (c) 2007 Steven Toth <stoth@linuxtv.org>
+ *  Copyright (c) 2009 Devin Heitmueller <dheitmueller@kernellabs.com>
+ *  Copyright (c) 2009 Davide Ferri <d.ferri@zero11.it>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/videodev2.h>
+#include <linux/delay.h>
+#include <linux/dvb/frontend.h>
+#include <linux/i2c.h>
+#include <linux/mutex.h>
+#include <asm/unaligned.h>
+
+#include "dvb_frontend.h"
+
+#include "xc4000.h"
+#include "tuner-i2c.h"
+#include "tuner-xc2028-types.h"
+
+static int debug;
+module_param(debug, int, 0644);
+MODULE_PARM_DESC(debug, "\n\t\tDebugging level (0 to 2, default: 0 (off)).");
+
+static int no_poweroff;
+module_param(no_poweroff, int, 0644);
+MODULE_PARM_DESC(no_poweroff, "\n\t\t1: keep device energized and with tuner "
+	"ready all the times.\n"
+	"\t\tFaster, but consumes more power and keeps the device hotter.\n"
+	"\t\t2: powers device off when not used.\n"
+	"\t\t0 (default): use device-specific default mode.");
+
+#define XC4000_AUDIO_STD_B		 1
+#define XC4000_AUDIO_STD_A2		 2
+#define XC4000_AUDIO_STD_K3		 4
+#define XC4000_AUDIO_STD_L		 8
+#define XC4000_AUDIO_STD_INPUT1		16
+#define XC4000_AUDIO_STD_MONO		32
+
+static int audio_std;
+module_param(audio_std, int, 0644);
+MODULE_PARM_DESC(audio_std, "\n\t\tAudio standard. XC4000 audio decoder "
+	"explicitly needs to know\n"
+	"\t\twhat audio standard is needed for some video standards with\n"
+	"\t\taudio A2 or NICAM.\n"
+	"\t\tThe valid settings are a sum of:\n"
+	"\t\t 1: use NICAM/B or A2/B instead of NICAM/A or A2/A\n"
+	"\t\t 2: use A2 instead of NICAM or BTSC\n"
+	"\t\t 4: use SECAM/K3 instead of K1\n"
+	"\t\t 8: use PAL-D/K audio for SECAM-D/K\n"
+	"\t\t16: use FM radio input 1 instead of input 2\n"
+	"\t\t32: use mono audio (the lower three bits are ignored)");
+
+#define XC4000_DEFAULT_FIRMWARE "xc4000.fw"
+
+static char firmware_name[30];
+module_param_string(firmware_name, firmware_name, sizeof(firmware_name), 0);
+MODULE_PARM_DESC(firmware_name, "\n\t\tFirmware file name. Allows overriding "
+	"the default firmware\n"
+	"\t\tname.");
+
+static DEFINE_MUTEX(xc4000_list_mutex);
+static LIST_HEAD(hybrid_tuner_instance_list);
+
+#define dprintk(level, fmt, arg...) if (debug >= level) \
+	printk(KERN_INFO "%s: " fmt, "xc4000", ## arg)
+
+/* struct for storing firmware table */
+struct firmware_description {
+	unsigned int  type;
+	v4l2_std_id   id;
+	__u16         int_freq;
+	unsigned char *ptr;
+	unsigned int  size;
+};
+
+struct firmware_properties {
+	unsigned int	type;
+	v4l2_std_id	id;
+	v4l2_std_id	std_req;
+	__u16		int_freq;
+	unsigned int	scode_table;
+	int		scode_nr;
+};
+
+struct xc4000_priv {
+	struct tuner_i2c_props i2c_props;
+	struct list_head hybrid_tuner_instance_list;
+	struct firmware_description *firm;
+	int	firm_size;
+	__u16	firm_version;
+	u32	if_khz;
+	u32	freq_hz;
+	u32	bandwidth;
+	u8	video_standard;
+	u8	rf_mode;
+	u8	card_type;
+	u8	ignore_i2c_write_errors;
+ /*	struct xc2028_ctrl	ctrl; */
+	struct firmware_properties cur_fw;
+	__u16	hwmodel;
+	__u16	hwvers;
+	struct mutex	lock;
+};
+
+/* Misc Defines */
+#define MAX_TV_STANDARD			24
+#define XC_MAX_I2C_WRITE_LENGTH		64
+#define XC_POWERED_DOWN			0x80000000U
+
+/* Signal Types */
+#define XC_RF_MODE_AIR			0
+#define XC_RF_MODE_CABLE		1
+
+/* Result codes */
+#define XC_RESULT_SUCCESS		0
+#define XC_RESULT_RESET_FAILURE		1
+#define XC_RESULT_I2C_WRITE_FAILURE	2
+#define XC_RESULT_I2C_READ_FAILURE	3
+#define XC_RESULT_OUT_OF_RANGE		5
+
+/* Product id */
+#define XC_PRODUCT_ID_FW_NOT_LOADED	0x2000
+#define XC_PRODUCT_ID_XC4000		0x0FA0
+#define XC_PRODUCT_ID_XC4100		0x1004
+
+/* Registers (Write-only) */
+#define XREG_INIT         0x00
+#define XREG_VIDEO_MODE   0x01
+#define XREG_AUDIO_MODE   0x02
+#define XREG_RF_FREQ      0x03
+#define XREG_D_CODE       0x04
+#define XREG_DIRECTSITTING_MODE 0x05
+#define XREG_SEEK_MODE    0x06
+#define XREG_POWER_DOWN   0x08
+#define XREG_SIGNALSOURCE 0x0A
+#define XREG_SMOOTHEDCVBS 0x0E
+#define XREG_AMPLITUDE    0x10
+
+/* Registers (Read-only) */
+#define XREG_ADC_ENV      0x00
+#define XREG_QUALITY      0x01
+#define XREG_FRAME_LINES  0x02
+#define XREG_HSYNC_FREQ   0x03
+#define XREG_LOCK         0x04
+#define XREG_FREQ_ERROR   0x05
+#define XREG_SNR          0x06
+#define XREG_VERSION      0x07
+#define XREG_PRODUCT_ID   0x08
+
+/*
+   Basic firmware description. This will remain with
+   the driver for documentation purposes.
+
+   This represents an I2C firmware file encoded as a
+   string of unsigned char. Format is as follows:
+
+   char[0  ]=len0_MSB  -> len = len_MSB * 256 + len_LSB
+   char[1  ]=len0_LSB  -> length of first write transaction
+   char[2  ]=data0 -> first byte to be sent
+   char[3  ]=data1
+   char[4  ]=data2
+   char[   ]=...
+   char[M  ]=dataN  -> last byte to be sent
+   char[M+1]=len1_MSB  -> len = len_MSB * 256 + len_LSB
+   char[M+2]=len1_LSB  -> length of second write transaction
+   char[M+3]=data0
+   char[M+4]=data1
+   ...
+   etc.
+
+   The [len] value should be interpreted as follows:
+
+   len= len_MSB _ len_LSB
+   len=1111_1111_1111_1111   : End of I2C_SEQUENCE
+   len=0000_0000_0000_0000   : Reset command: Do hardware reset
+   len=0NNN_NNNN_NNNN_NNNN   : Normal transaction: number of bytes = {1:32767)
+   len=1WWW_WWWW_WWWW_WWWW   : Wait command: wait for {1:32767} ms
+
+   For the RESET and WAIT commands, the two following bytes will contain
+   immediately the length of the following transaction.
+*/
+
+struct XC_TV_STANDARD {
+	const char  *Name;
+	u16	    AudioMode;
+	u16	    VideoMode;
+	u16	    int_freq;
+};
+
+/* Tuner standards */
+#define XC4000_MN_NTSC_PAL_BTSC		0
+#define XC4000_MN_NTSC_PAL_A2		1
+#define XC4000_MN_NTSC_PAL_EIAJ		2
+#define XC4000_MN_NTSC_PAL_Mono		3
+#define XC4000_BG_PAL_A2		4
+#define XC4000_BG_PAL_NICAM		5
+#define XC4000_BG_PAL_MONO		6
+#define XC4000_I_PAL_NICAM		7
+#define XC4000_I_PAL_NICAM_MONO		8
+#define XC4000_DK_PAL_A2		9
+#define XC4000_DK_PAL_NICAM		10
+#define XC4000_DK_PAL_MONO		11
+#define XC4000_DK_SECAM_A2DK1		12
+#define XC4000_DK_SECAM_A2LDK3		13
+#define XC4000_DK_SECAM_A2MONO		14
+#define XC4000_DK_SECAM_NICAM		15
+#define XC4000_L_SECAM_NICAM		16
+#define XC4000_LC_SECAM_NICAM		17
+#define XC4000_DTV6			18
+#define XC4000_DTV8			19
+#define XC4000_DTV7_8			20
+#define XC4000_DTV7			21
+#define XC4000_FM_Radio_INPUT2		22
+#define XC4000_FM_Radio_INPUT1		23
+
+static struct XC_TV_STANDARD XC4000_Standard[MAX_TV_STANDARD] = {
+	{"M/N-NTSC/PAL-BTSC",	0x0000, 0x80A0, 4500},
+	{"M/N-NTSC/PAL-A2",	0x0000, 0x80A0, 4600},
+	{"M/N-NTSC/PAL-EIAJ",	0x0040, 0x80A0, 4500},
+	{"M/N-NTSC/PAL-Mono",	0x0078, 0x80A0, 4500},
+	{"B/G-PAL-A2",		0x0000, 0x8159, 5640},
+	{"B/G-PAL-NICAM",	0x0004, 0x8159, 5740},
+	{"B/G-PAL-MONO",	0x0078, 0x8159, 5500},
+	{"I-PAL-NICAM",		0x0080, 0x8049, 6240},
+	{"I-PAL-NICAM-MONO",	0x0078, 0x8049, 6000},
+	{"D/K-PAL-A2",		0x0000, 0x8049, 6380},
+	{"D/K-PAL-NICAM",	0x0080, 0x8049, 6200},
+	{"D/K-PAL-MONO",	0x0078, 0x8049, 6500},
+	{"D/K-SECAM-A2 DK1",	0x0000, 0x8049, 6340},
+	{"D/K-SECAM-A2 L/DK3",	0x0000, 0x8049, 6000},
+	{"D/K-SECAM-A2 MONO",	0x0078, 0x8049, 6500},
+	{"D/K-SECAM-NICAM",	0x0080, 0x8049, 6200},
+	{"L-SECAM-NICAM",	0x8080, 0x0009, 6200},
+	{"L'-SECAM-NICAM",	0x8080, 0x4009, 6200},
+	{"DTV6",		0x00C0, 0x8002,    0},
+	{"DTV8",		0x00C0, 0x800B,    0},
+	{"DTV7/8",		0x00C0, 0x801B,    0},
+	{"DTV7",		0x00C0, 0x8007,    0},
+	{"FM Radio-INPUT2",	0x0008, 0x9800,10700},
+	{"FM Radio-INPUT1",	0x0008, 0x9000,10700}
+};
+
+static int xc4000_readreg(struct xc4000_priv *priv, u16 reg, u16 *val);
+static int xc4000_TunerReset(struct dvb_frontend *fe);
+static void xc_debug_dump(struct xc4000_priv *priv);
+
+static int xc_send_i2c_data(struct xc4000_priv *priv, u8 *buf, int len)
+{
+	struct i2c_msg msg = { .addr = priv->i2c_props.addr,
+			       .flags = 0, .buf = buf, .len = len };
+	if (i2c_transfer(priv->i2c_props.adap, &msg, 1) != 1) {
+		if (priv->ignore_i2c_write_errors == 0) {
+			printk(KERN_ERR "xc4000: I2C write failed (len=%i)\n",
+			       len);
+			if (len == 4) {
+				printk("bytes %02x %02x %02x %02x\n", buf[0],
+				       buf[1], buf[2], buf[3]);
+			}
+			return XC_RESULT_I2C_WRITE_FAILURE;
+		}
+	}
+	return XC_RESULT_SUCCESS;
+}
+
+static void xc_wait(int wait_ms)
+{
+	msleep(wait_ms);
+}
+
+static int xc4000_TunerReset(struct dvb_frontend *fe)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+	int ret;
+
+	dprintk(1, "%s()\n", __func__);
+
+	if (fe->callback) {
+		ret = fe->callback(((fe->dvb) && (fe->dvb->priv)) ?
+					   fe->dvb->priv :
+					   priv->i2c_props.adap->algo_data,
+					   DVB_FRONTEND_COMPONENT_TUNER,
+					   XC4000_TUNER_RESET, 0);
+		if (ret) {
+			printk(KERN_ERR "xc4000: reset failed\n");
+			return XC_RESULT_RESET_FAILURE;
+		}
+	} else {
+		printk(KERN_ERR "xc4000: no tuner reset callback function, fatal\n");
+		return XC_RESULT_RESET_FAILURE;
+	}
+	return XC_RESULT_SUCCESS;
+}
+
+static int xc_write_reg(struct xc4000_priv *priv, u16 regAddr, u16 i2cData)
+{
+	u8 buf[4];
+	int result;
+
+	buf[0] = (regAddr >> 8) & 0xFF;
+	buf[1] = regAddr & 0xFF;
+	buf[2] = (i2cData >> 8) & 0xFF;
+	buf[3] = i2cData & 0xFF;
+	result = xc_send_i2c_data(priv, buf, 4);
+
+	return result;
+}
+
+static int xc_load_i2c_sequence(struct dvb_frontend *fe, const u8 *i2c_sequence)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+
+	int i, nbytes_to_send, result;
+	unsigned int len, pos, index;
+	u8 buf[XC_MAX_I2C_WRITE_LENGTH];
+
+	index = 0;
+	while ((i2c_sequence[index] != 0xFF) ||
+		(i2c_sequence[index + 1] != 0xFF)) {
+		len = i2c_sequence[index] * 256 + i2c_sequence[index+1];
+		if (len == 0x0000) {
+			/* RESET command */
+			index += 2;
+#if 0			/* not needed, as already called by check_firmware() */
+			result = xc4000_TunerReset(fe);
+			if (result != XC_RESULT_SUCCESS)
+				return result;
+#endif
+		} else if (len & 0x8000) {
+			/* WAIT command */
+			xc_wait(len & 0x7FFF);
+			index += 2;
+		} else {
+			/* Send i2c data whilst ensuring individual transactions
+			 * do not exceed XC_MAX_I2C_WRITE_LENGTH bytes.
+			 */
+			index += 2;
+			buf[0] = i2c_sequence[index];
+			buf[1] = i2c_sequence[index + 1];
+			pos = 2;
+			while (pos < len) {
+				if ((len - pos) > XC_MAX_I2C_WRITE_LENGTH - 2)
+					nbytes_to_send =
+						XC_MAX_I2C_WRITE_LENGTH;
+				else
+					nbytes_to_send = (len - pos + 2);
+				for (i = 2; i < nbytes_to_send; i++) {
+					buf[i] = i2c_sequence[index + pos +
+						i - 2];
+				}
+				result = xc_send_i2c_data(priv, buf,
+					nbytes_to_send);
+
+				if (result != XC_RESULT_SUCCESS)
+					return result;
+
+				pos += nbytes_to_send - 2;
+			}
+			index += len;
+		}
+	}
+	return XC_RESULT_SUCCESS;
+}
+
+static int xc_SetTVStandard(struct xc4000_priv *priv,
+	u16 VideoMode, u16 AudioMode)
+{
+	int ret;
+	dprintk(1, "%s(0x%04x,0x%04x)\n", __func__, VideoMode, AudioMode);
+	dprintk(1, "%s() Standard = %s\n",
+		__func__,
+		XC4000_Standard[priv->video_standard].Name);
+
+	/* Don't complain when the request fails because of i2c stretching */
+	priv->ignore_i2c_write_errors = 1;
+
+	ret = xc_write_reg(priv, XREG_VIDEO_MODE, VideoMode);
+	if (ret == XC_RESULT_SUCCESS)
+		ret = xc_write_reg(priv, XREG_AUDIO_MODE, AudioMode);
+
+	priv->ignore_i2c_write_errors = 0;
+
+	return ret;
+}
+
+static int xc_SetSignalSource(struct xc4000_priv *priv, u16 rf_mode)
+{
+	dprintk(1, "%s(%d) Source = %s\n", __func__, rf_mode,
+		rf_mode == XC_RF_MODE_AIR ? "ANTENNA" : "CABLE");
+
+	if ((rf_mode != XC_RF_MODE_AIR) && (rf_mode != XC_RF_MODE_CABLE)) {
+		rf_mode = XC_RF_MODE_CABLE;
+		printk(KERN_ERR
+			"%s(), Invalid mode, defaulting to CABLE",
+			__func__);
+	}
+	return xc_write_reg(priv, XREG_SIGNALSOURCE, rf_mode);
+}
+
+static const struct dvb_tuner_ops xc4000_tuner_ops;
+
+static int xc_set_RF_frequency(struct xc4000_priv *priv, u32 freq_hz)
+{
+	u16 freq_code;
+
+	dprintk(1, "%s(%u)\n", __func__, freq_hz);
+
+	if ((freq_hz > xc4000_tuner_ops.info.frequency_max) ||
+		(freq_hz < xc4000_tuner_ops.info.frequency_min))
+		return XC_RESULT_OUT_OF_RANGE;
+
+	freq_code = (u16)(freq_hz / 15625);
+
+	/* WAS: Starting in firmware version 1.1.44, Xceive recommends using the
+	   FINERFREQ for all normal tuning (the doc indicates reg 0x03 should
+	   only be used for fast scanning for channel lock) */
+	return xc_write_reg(priv, XREG_RF_FREQ, freq_code); /* WAS: XREG_FINERFREQ */
+}
+
+static int xc_get_ADC_Envelope(struct xc4000_priv *priv, u16 *adc_envelope)
+{
+	return xc4000_readreg(priv, XREG_ADC_ENV, adc_envelope);
+}
+
+static int xc_get_frequency_error(struct xc4000_priv *priv, u32 *freq_error_hz)
+{
+	int result;
+	u16 regData;
+	u32 tmp;
+
+	result = xc4000_readreg(priv, XREG_FREQ_ERROR, &regData);
+	if (result != XC_RESULT_SUCCESS)
+		return result;
+
+	tmp = (u32)regData & 0xFFFFU;
+	tmp = (tmp < 0x8000U ? tmp : 0x10000U - tmp);
+	(*freq_error_hz) = tmp * 15625;
+	return result;
+}
+
+static int xc_get_lock_status(struct xc4000_priv *priv, u16 *lock_status)
+{
+	return xc4000_readreg(priv, XREG_LOCK, lock_status);
+}
+
+static int xc_get_version(struct xc4000_priv *priv,
+	u8 *hw_majorversion, u8 *hw_minorversion,
+	u8 *fw_majorversion, u8 *fw_minorversion)
+{
+	u16 data;
+	int result;
+
+	result = xc4000_readreg(priv, XREG_VERSION, &data);
+	if (result != XC_RESULT_SUCCESS)
+		return result;
+
+	(*hw_majorversion) = (data >> 12) & 0x0F;
+	(*hw_minorversion) = (data >>  8) & 0x0F;
+	(*fw_majorversion) = (data >>  4) & 0x0F;
+	(*fw_minorversion) = data & 0x0F;
+
+	return 0;
+}
+
+static int xc_get_hsync_freq(struct xc4000_priv *priv, u32 *hsync_freq_hz)
+{
+	u16 regData;
+	int result;
+
+	result = xc4000_readreg(priv, XREG_HSYNC_FREQ, &regData);
+	if (result != XC_RESULT_SUCCESS)
+		return result;
+
+	(*hsync_freq_hz) = ((regData & 0x0fff) * 763)/100;
+	return result;
+}
+
+static int xc_get_frame_lines(struct xc4000_priv *priv, u16 *frame_lines)
+{
+	return xc4000_readreg(priv, XREG_FRAME_LINES, frame_lines);
+}
+
+static int xc_get_quality(struct xc4000_priv *priv, u16 *quality)
+{
+	return xc4000_readreg(priv, XREG_QUALITY, quality);
+}
+
+static u16 WaitForLock(struct xc4000_priv *priv)
+{
+	u16 lockState = 0;
+	int watchDogCount = 40;
+
+	while ((lockState == 0) && (watchDogCount > 0)) {
+		xc_get_lock_status(priv, &lockState);
+		if (lockState != 1) {
+			xc_wait(5);
+			watchDogCount--;
+		}
+	}
+	return lockState;
+}
+
+static int xc_tune_channel(struct xc4000_priv *priv, u32 freq_hz)
+{
+	int	found = 1;
+	int	result;
+
+	dprintk(1, "%s(%u)\n", __func__, freq_hz);
+
+	/* Don't complain when the request fails because of i2c stretching */
+	priv->ignore_i2c_write_errors = 1;
+	result = xc_set_RF_frequency(priv, freq_hz);
+	priv->ignore_i2c_write_errors = 0;
+
+	if (result != XC_RESULT_SUCCESS)
+		return 0;
+
+	/* wait for lock only in analog TV mode */
+	if ((priv->cur_fw.type & (FM | DTV6 | DTV7 | DTV78 | DTV8)) == 0) {
+		if (WaitForLock(priv) != 1)
+			found = 0;
+	}
+
+	/* Wait for stats to stabilize.
+	 * Frame Lines needs two frame times after initial lock
+	 * before it is valid.
+	 */
+	xc_wait(debug ? 100 : 10);
+
+	if (debug)
+		xc_debug_dump(priv);
+
+	return found;
+}
+
+static int xc4000_readreg(struct xc4000_priv *priv, u16 reg, u16 *val)
+{
+	u8 buf[2] = { reg >> 8, reg & 0xff };
+	u8 bval[2] = { 0, 0 };
+	struct i2c_msg msg[2] = {
+		{ .addr = priv->i2c_props.addr,
+			.flags = 0, .buf = &buf[0], .len = 2 },
+		{ .addr = priv->i2c_props.addr,
+			.flags = I2C_M_RD, .buf = &bval[0], .len = 2 },
+	};
+
+	if (i2c_transfer(priv->i2c_props.adap, msg, 2) != 2) {
+		printk(KERN_WARNING "xc4000: I2C read failed\n");
+		return -EREMOTEIO;
+	}
+
+	*val = (bval[0] << 8) | bval[1];
+	return XC_RESULT_SUCCESS;
+}
+
+#define dump_firm_type(t)	dump_firm_type_and_int_freq(t, 0)
+static void dump_firm_type_and_int_freq(unsigned int type, u16 int_freq)
+{
+	 if (type & BASE)
+		printk("BASE ");
+	 if (type & INIT1)
+		printk("INIT1 ");
+	 if (type & F8MHZ)
+		printk("F8MHZ ");
+	 if (type & MTS)
+		printk("MTS ");
+	 if (type & D2620)
+		printk("D2620 ");
+	 if (type & D2633)
+		printk("D2633 ");
+	 if (type & DTV6)
+		printk("DTV6 ");
+	 if (type & QAM)
+		printk("QAM ");
+	 if (type & DTV7)
+		printk("DTV7 ");
+	 if (type & DTV78)
+		printk("DTV78 ");
+	 if (type & DTV8)
+		printk("DTV8 ");
+	 if (type & FM)
+		printk("FM ");
+	 if (type & INPUT1)
+		printk("INPUT1 ");
+	 if (type & LCD)
+		printk("LCD ");
+	 if (type & NOGD)
+		printk("NOGD ");
+	 if (type & MONO)
+		printk("MONO ");
+	 if (type & ATSC)
+		printk("ATSC ");
+	 if (type & IF)
+		printk("IF ");
+	 if (type & LG60)
+		printk("LG60 ");
+	 if (type & ATI638)
+		printk("ATI638 ");
+	 if (type & OREN538)
+		printk("OREN538 ");
+	 if (type & OREN36)
+		printk("OREN36 ");
+	 if (type & TOYOTA388)
+		printk("TOYOTA388 ");
+	 if (type & TOYOTA794)
+		printk("TOYOTA794 ");
+	 if (type & DIBCOM52)
+		printk("DIBCOM52 ");
+	 if (type & ZARLINK456)
+		printk("ZARLINK456 ");
+	 if (type & CHINA)
+		printk("CHINA ");
+	 if (type & F6MHZ)
+		printk("F6MHZ ");
+	 if (type & INPUT2)
+		printk("INPUT2 ");
+	 if (type & SCODE)
+		printk("SCODE ");
+	 if (type & HAS_IF)
+		printk("HAS_IF_%d ", int_freq);
+}
+
+static int seek_firmware(struct dvb_frontend *fe, unsigned int type,
+			 v4l2_std_id *id)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+	int		i, best_i = -1;
+	unsigned int	best_nr_diffs = 255U;
+
+	if (!priv->firm) {
+		printk("Error! firmware not loaded\n");
+		return -EINVAL;
+	}
+
+	if (((type & ~SCODE) == 0) && (*id == 0))
+		*id = V4L2_STD_PAL;
+
+	/* Seek for generic video standard match */
+	for (i = 0; i < priv->firm_size; i++) {
+		v4l2_std_id	id_diff_mask =
+			(priv->firm[i].id ^ (*id)) & (*id);
+		unsigned int	type_diff_mask =
+			(priv->firm[i].type ^ type)
+			& (BASE_TYPES | DTV_TYPES | LCD | NOGD | MONO | SCODE);
+		unsigned int	nr_diffs;
+
+		if (type_diff_mask
+		    & (BASE | INIT1 | FM | DTV6 | DTV7 | DTV78 | DTV8 | SCODE))
+			continue;
+
+		nr_diffs = hweight64(id_diff_mask) + hweight32(type_diff_mask);
+		if (!nr_diffs)	/* Supports all the requested standards */
+			goto found;
+
+		if (nr_diffs < best_nr_diffs) {
+			best_nr_diffs = nr_diffs;
+			best_i = i;
+		}
+	}
+
+	/* FIXME: Would make sense to seek for type "hint" match ? */
+	if (best_i < 0) {
+		i = -ENOENT;
+		goto ret;
+	}
+
+	if (best_nr_diffs > 0U) {
+		printk("Selecting best matching firmware (%u bits differ) for "
+		       "type=", best_nr_diffs);
+		printk("(%x), id %016llx:\n", type, (unsigned long long)*id);
+		i = best_i;
+	}
+
+found:
+	*id = priv->firm[i].id;
+
+ret:
+	if (debug) {
+		printk("%s firmware for type=", (i < 0) ? "Can't find" :
+		       "Found");
+		dump_firm_type(type);
+		printk("(%x), id %016llx.\n", type, (unsigned long long)*id);
+	}
+	return i;
+}
+
+static int load_firmware(struct dvb_frontend *fe, unsigned int type,
+			 v4l2_std_id *id)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+	int                pos, rc;
+	unsigned char      *p;
+
+	pos = seek_firmware(fe, type, id);
+	if (pos < 0)
+		return pos;
+
+	p = priv->firm[pos].ptr;
+
+	/* Don't complain when the request fails because of i2c stretching */
+	priv->ignore_i2c_write_errors = 1;
+
+	rc = xc_load_i2c_sequence(fe, p);
+
+	priv->ignore_i2c_write_errors = 0;
+
+	return rc;
+}
+
+static int xc4000_fwupload(struct dvb_frontend *fe)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+	const struct firmware *fw   = NULL;
+	const unsigned char   *p, *endp;
+	int                   rc = 0;
+	int		      n, n_array;
+	char		      name[33];
+	const char	      *fname;
+
+	if (firmware_name[0] != '\0')
+		fname = firmware_name;
+	else
+		fname = XC4000_DEFAULT_FIRMWARE;
+
+	printk("Reading firmware %s\n",  fname);
+	rc = request_firmware(&fw, fname, priv->i2c_props.adap->dev.parent);
+	if (rc < 0) {
+		if (rc == -ENOENT)
+			printk("Error: firmware %s not found.\n",
+				   fname);
+		else
+			printk("Error %d while requesting firmware %s \n",
+				   rc, fname);
+
+		return rc;
+	}
+	p = fw->data;
+	endp = p + fw->size;
+
+	if (fw->size < sizeof(name) - 1 + 2 + 2) {
+		printk("Error: firmware file %s has invalid size!\n",
+		       fname);
+		goto corrupt;
+	}
+
+	memcpy(name, p, sizeof(name) - 1);
+	name[sizeof(name) - 1] = 0;
+	p += sizeof(name) - 1;
+
+	priv->firm_version = get_unaligned_le16(p);
+	p += 2;
+
+	n_array = get_unaligned_le16(p);
+	p += 2;
+
+	dprintk(1, "Loading %d firmware images from %s, type: %s, ver %d.%d\n",
+		n_array, fname, name,
+		priv->firm_version >> 8, priv->firm_version & 0xff);
+
+	priv->firm = kzalloc(sizeof(*priv->firm) * n_array, GFP_KERNEL);
+	if (priv->firm == NULL) {
+		printk("Not enough memory to load firmware file.\n");
+		rc = -ENOMEM;
+		goto err;
+	}
+	priv->firm_size = n_array;
+
+	n = -1;
+	while (p < endp) {
+		__u32 type, size;
+		v4l2_std_id id;
+		__u16 int_freq = 0;
+
+		n++;
+		if (n >= n_array) {
+			printk("More firmware images in file than "
+			       "were expected!\n");
+			goto corrupt;
+		}
+
+		/* Checks if there's enough bytes to read */
+		if (endp - p < sizeof(type) + sizeof(id) + sizeof(size))
+			goto header;
+
+		type = get_unaligned_le32(p);
+		p += sizeof(type);
+
+		id = get_unaligned_le64(p);
+		p += sizeof(id);
+
+		if (type & HAS_IF) {
+			int_freq = get_unaligned_le16(p);
+			p += sizeof(int_freq);
+			if (endp - p < sizeof(size))
+				goto header;
+		}
+
+		size = get_unaligned_le32(p);
+		p += sizeof(size);
+
+		if (!size || size > endp - p) {
+			printk("Firmware type (%x), id %llx is corrupted "
+			       "(size=%d, expected %d)\n",
+			       type, (unsigned long long)id,
+			       (unsigned)(endp - p), size);
+			goto corrupt;
+		}
+
+		priv->firm[n].ptr = kzalloc(size, GFP_KERNEL);
+		if (priv->firm[n].ptr == NULL) {
+			printk("Not enough memory to load firmware file.\n");
+			rc = -ENOMEM;
+			goto err;
+		}
+
+		if (debug) {
+			printk("Reading firmware type ");
+			dump_firm_type_and_int_freq(type, int_freq);
+			printk("(%x), id %llx, size=%d.\n",
+			       type, (unsigned long long)id, size);
+		}
+
+		memcpy(priv->firm[n].ptr, p, size);
+		priv->firm[n].type = type;
+		priv->firm[n].id   = id;
+		priv->firm[n].size = size;
+		priv->firm[n].int_freq = int_freq;
+
+		p += size;
+	}
+
+	if (n + 1 != priv->firm_size) {
+		printk("Firmware file is incomplete!\n");
+		goto corrupt;
+	}
+
+	goto done;
+
+header:
+	printk("Firmware header is incomplete!\n");
+corrupt:
+	rc = -EINVAL;
+	printk("Error: firmware file is corrupted!\n");
+
+err:
+	printk("Releasing partially loaded firmware file.\n");
+
+done:
+	release_firmware(fw);
+	if (rc == 0)
+		dprintk(1, "Firmware files loaded.\n");
+
+	return rc;
+}
+
+static int load_scode(struct dvb_frontend *fe, unsigned int type,
+			 v4l2_std_id *id, __u16 int_freq, int scode)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+	int		pos, rc;
+	unsigned char	*p;
+	u8		scode_buf[13];
+	u8		indirect_mode[5];
+
+	dprintk(1, "%s called int_freq=%d\n", __func__, int_freq);
+
+	if (!int_freq) {
+		pos = seek_firmware(fe, type, id);
+		if (pos < 0)
+			return pos;
+	} else {
+		for (pos = 0; pos < priv->firm_size; pos++) {
+			if ((priv->firm[pos].int_freq == int_freq) &&
+			    (priv->firm[pos].type & HAS_IF))
+				break;
+		}
+		if (pos == priv->firm_size)
+			return -ENOENT;
+	}
+
+	p = priv->firm[pos].ptr;
+
+	if (priv->firm[pos].size != 12 * 16 || scode >= 16)
+		return -EINVAL;
+	p += 12 * scode;
+
+	tuner_info("Loading SCODE for type=");
+	dump_firm_type_and_int_freq(priv->firm[pos].type,
+				    priv->firm[pos].int_freq);
+	printk("(%x), id %016llx.\n", priv->firm[pos].type,
+	       (unsigned long long)*id);
+
+	scode_buf[0] = 0x00;
+	memcpy(&scode_buf[1], p, 12);
+
+	/* Enter direct-mode */
+	rc = xc_write_reg(priv, XREG_DIRECTSITTING_MODE, 0);
+	if (rc < 0) {
+		printk("failed to put device into direct mode!\n");
+		return -EIO;
+	}
+
+	rc = xc_send_i2c_data(priv, scode_buf, 13);
+	if (rc != XC_RESULT_SUCCESS) {
+		/* Even if the send failed, make sure we set back to indirect
+		   mode */
+		printk("Failed to set scode %d\n", rc);
+	}
+
+	/* Switch back to indirect-mode */
+	memset(indirect_mode, 0, sizeof(indirect_mode));
+	indirect_mode[4] = 0x88;
+	xc_send_i2c_data(priv, indirect_mode, sizeof(indirect_mode));
+	msleep(10);
+
+	return 0;
+}
+
+static int check_firmware(struct dvb_frontend *fe, unsigned int type,
+			  v4l2_std_id std, __u16 int_freq)
+{
+	struct xc4000_priv         *priv = fe->tuner_priv;
+	struct firmware_properties new_fw;
+	int			   rc = 0, is_retry = 0;
+	u16			   version = 0, hwmodel;
+	v4l2_std_id		   std0;
+	u8			   hw_major, hw_minor, fw_major, fw_minor;
+
+	dprintk(1, "%s called\n", __func__);
+
+	if (!priv->firm) {
+		rc = xc4000_fwupload(fe);
+		if (rc < 0)
+			return rc;
+	}
+
+#ifdef DJH_DEBUG
+	if (priv->ctrl.mts && !(type & FM))
+		type |= MTS;
+#endif
+
+retry:
+	new_fw.type = type;
+	new_fw.id = std;
+	new_fw.std_req = std;
+	new_fw.scode_table = SCODE /* | priv->ctrl.scode_table */;
+	new_fw.scode_nr = 0;
+	new_fw.int_freq = int_freq;
+
+	dprintk(1, "checking firmware, user requested type=");
+	if (debug) {
+		dump_firm_type(new_fw.type);
+		printk("(%x), id %016llx, ", new_fw.type,
+		       (unsigned long long)new_fw.std_req);
+		if (!int_freq) {
+			printk("scode_tbl ");
+#ifdef DJH_DEBUG
+			dump_firm_type(priv->ctrl.scode_table);
+			printk("(%x), ", priv->ctrl.scode_table);
+#endif
+		} else
+			printk("int_freq %d, ", new_fw.int_freq);
+		printk("scode_nr %d\n", new_fw.scode_nr);
+	}
+
+	/* No need to reload base firmware if it matches */
+	if (priv->cur_fw.type & BASE) {
+		dprintk(1, "BASE firmware not changed.\n");
+		goto skip_base;
+	}
+
+	/* Updating BASE - forget about all currently loaded firmware */
+	memset(&priv->cur_fw, 0, sizeof(priv->cur_fw));
+
+	/* Reset is needed before loading firmware */
+	rc = xc4000_TunerReset(fe);
+	if (rc < 0)
+		goto fail;
+
+	/* BASE firmwares are all std0 */
+	std0 = 0;
+	rc = load_firmware(fe, BASE, &std0);
+	if (rc < 0) {
+		printk("Error %d while loading base firmware\n", rc);
+		goto fail;
+	}
+
+	/* Load INIT1, if needed */
+	dprintk(1, "Load init1 firmware, if exists\n");
+
+	rc = load_firmware(fe, BASE | INIT1, &std0);
+	if (rc == -ENOENT)
+		rc = load_firmware(fe, BASE | INIT1, &std0);
+	if (rc < 0 && rc != -ENOENT) {
+		tuner_err("Error %d while loading init1 firmware\n",
+			  rc);
+		goto fail;
+	}
+
+skip_base:
+	/*
+	 * No need to reload standard specific firmware if base firmware
+	 * was not reloaded and requested video standards have not changed.
+	 */
+	if (priv->cur_fw.type == (BASE | new_fw.type) &&
+	    priv->cur_fw.std_req == std) {
+		dprintk(1, "Std-specific firmware already loaded.\n");
+		goto skip_std_specific;
+	}
+
+	/* Reloading std-specific firmware forces a SCODE update */
+	priv->cur_fw.scode_table = 0;
+
+	/* Load the standard firmware */
+	rc = load_firmware(fe, new_fw.type, &new_fw.id);
+
+	if (rc < 0)
+		goto fail;
+
+skip_std_specific:
+	if (priv->cur_fw.scode_table == new_fw.scode_table &&
+	    priv->cur_fw.scode_nr == new_fw.scode_nr) {
+		dprintk(1, "SCODE firmware already loaded.\n");
+		goto check_device;
+	}
+
+	/* Load SCODE firmware, if exists */
+	rc = load_scode(fe, new_fw.type | new_fw.scode_table, &new_fw.id,
+			new_fw.int_freq, new_fw.scode_nr);
+	if (rc != XC_RESULT_SUCCESS)
+		dprintk(1, "load scode failed %d\n", rc);
+
+check_device:
+	rc = xc4000_readreg(priv, XREG_PRODUCT_ID, &hwmodel);
+
+	if (xc_get_version(priv, &hw_major, &hw_minor, &fw_major,
+			   &fw_minor) != XC_RESULT_SUCCESS) {
+		printk("Unable to read tuner registers.\n");
+		goto fail;
+	}
+
+	dprintk(1, "Device is Xceive %d version %d.%d, "
+		"firmware version %d.%d\n",
+		hwmodel, hw_major, hw_minor, fw_major, fw_minor);
+
+	/* Check firmware version against what we downloaded. */
+#ifdef DJH_DEBUG
+	if (priv->firm_version != ((version & 0xf0) << 4 | (version & 0x0f))) {
+		printk("Incorrect readback of firmware version %x.\n",
+		       (version & 0xff));
+		goto fail;
+	}
+#endif
+
+	/* Check that the tuner hardware model remains consistent over time. */
+	if (priv->hwmodel == 0 &&
+	    (hwmodel == XC_PRODUCT_ID_XC4000 ||
+	     hwmodel == XC_PRODUCT_ID_XC4100)) {
+		priv->hwmodel = hwmodel;
+		priv->hwvers  = version & 0xff00;
+	} else if (priv->hwmodel == 0 || priv->hwmodel != hwmodel ||
+		   priv->hwvers != (version & 0xff00)) {
+		printk("Read invalid device hardware information - tuner "
+		       "hung?\n");
+		goto fail;
+	}
+
+	memcpy(&priv->cur_fw, &new_fw, sizeof(priv->cur_fw));
+
+	/*
+	 * By setting BASE in cur_fw.type only after successfully loading all
+	 * firmwares, we can:
+	 * 1. Identify that BASE firmware with type=0 has been loaded;
+	 * 2. Tell whether BASE firmware was just changed the next time through.
+	 */
+	priv->cur_fw.type |= BASE;
+
+	return 0;
+
+fail:
+	memset(&priv->cur_fw, 0, sizeof(priv->cur_fw));
+	if (!is_retry) {
+		msleep(50);
+		is_retry = 1;
+		dprintk(1, "Retrying firmware load\n");
+		goto retry;
+	}
+
+	if (rc == -ENOENT)
+		rc = -EINVAL;
+	return rc;
+}
+
+static void xc_debug_dump(struct xc4000_priv *priv)
+{
+	u16	adc_envelope;
+	u32	freq_error_hz = 0;
+	u16	lock_status;
+	u32	hsync_freq_hz = 0;
+	u16	frame_lines;
+	u16	quality;
+	u8	hw_majorversion = 0, hw_minorversion = 0;
+	u8	fw_majorversion = 0, fw_minorversion = 0;
+
+	xc_get_ADC_Envelope(priv, &adc_envelope);
+	dprintk(1, "*** ADC envelope (0-1023) = %d\n", adc_envelope);
+
+	xc_get_frequency_error(priv, &freq_error_hz);
+	dprintk(1, "*** Frequency error = %d Hz\n", freq_error_hz);
+
+	xc_get_lock_status(priv, &lock_status);
+	dprintk(1, "*** Lock status (0-Wait, 1-Locked, 2-No-signal) = %d\n",
+		lock_status);
+
+	xc_get_version(priv, &hw_majorversion, &hw_minorversion,
+		       &fw_majorversion, &fw_minorversion);
+	dprintk(1, "*** HW: V%02x.%02x, FW: V%02x.%02x\n",
+		hw_majorversion, hw_minorversion,
+		fw_majorversion, fw_minorversion);
+
+	if (priv->video_standard < XC4000_DTV6) {
+		xc_get_hsync_freq(priv, &hsync_freq_hz);
+		dprintk(1, "*** Horizontal sync frequency = %d Hz\n",
+			hsync_freq_hz);
+
+		xc_get_frame_lines(priv, &frame_lines);
+		dprintk(1, "*** Frame lines = %d\n", frame_lines);
+	}
+
+	xc_get_quality(priv, &quality);
+	dprintk(1, "*** Quality (0:<8dB, 7:>56dB) = %d\n", quality);
+}
+
+static int xc4000_set_params(struct dvb_frontend *fe,
+	struct dvb_frontend_parameters *params)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+	unsigned int type;
+	int	ret = -EREMOTEIO;
+
+	dprintk(1, "%s() frequency=%d (Hz)\n", __func__, params->frequency);
+
+	mutex_lock(&priv->lock);
+
+	if (fe->ops.info.type == FE_ATSC) {
+		dprintk(1, "%s() ATSC\n", __func__);
+		switch (params->u.vsb.modulation) {
+		case VSB_8:
+		case VSB_16:
+			dprintk(1, "%s() VSB modulation\n", __func__);
+			priv->rf_mode = XC_RF_MODE_AIR;
+			priv->freq_hz = params->frequency - 1750000;
+			priv->bandwidth = BANDWIDTH_6_MHZ;
+			priv->video_standard = XC4000_DTV6;
+			type = DTV6;
+			break;
+		case QAM_64:
+		case QAM_256:
+		case QAM_AUTO:
+			dprintk(1, "%s() QAM modulation\n", __func__);
+			priv->rf_mode = XC_RF_MODE_CABLE;
+			priv->freq_hz = params->frequency - 1750000;
+			priv->bandwidth = BANDWIDTH_6_MHZ;
+			priv->video_standard = XC4000_DTV6;
+			type = DTV6;
+			break;
+		default:
+			ret = -EINVAL;
+			goto fail;
+		}
+	} else if (fe->ops.info.type == FE_OFDM) {
+		dprintk(1, "%s() OFDM\n", __func__);
+		switch (params->u.ofdm.bandwidth) {
+		case BANDWIDTH_6_MHZ:
+			priv->bandwidth = BANDWIDTH_6_MHZ;
+			priv->video_standard = XC4000_DTV6;
+			priv->freq_hz = params->frequency - 1750000;
+			type = DTV6;
+			break;
+		case BANDWIDTH_7_MHZ:
+			priv->bandwidth = BANDWIDTH_7_MHZ;
+			priv->video_standard = XC4000_DTV7;
+			priv->freq_hz = params->frequency - 2250000;
+			type = DTV7;
+			break;
+		case BANDWIDTH_8_MHZ:
+			priv->bandwidth = BANDWIDTH_8_MHZ;
+			priv->video_standard = XC4000_DTV8;
+			priv->freq_hz = params->frequency - 2750000;
+			type = DTV8;
+			break;
+		case BANDWIDTH_AUTO:
+			if (params->frequency < 400000000) {
+				priv->bandwidth = BANDWIDTH_7_MHZ;
+				priv->freq_hz = params->frequency - 2250000;
+			} else {
+				priv->bandwidth = BANDWIDTH_8_MHZ;
+				priv->freq_hz = params->frequency - 2750000;
+			}
+			priv->video_standard = XC4000_DTV7_8;
+			type = DTV78;
+			break;
+		default:
+			printk(KERN_ERR "xc4000 bandwidth not set!\n");
+			ret = -EINVAL;
+			goto fail;
+		}
+		priv->rf_mode = XC_RF_MODE_AIR;
+	} else {
+		printk(KERN_ERR "xc4000 modulation type not supported!\n");
+		ret = -EINVAL;
+		goto fail;
+	}
+
+	dprintk(1, "%s() frequency=%d (compensated)\n",
+		__func__, priv->freq_hz);
+
+	/* Make sure the correct firmware type is loaded */
+	if (check_firmware(fe, type, 0, priv->if_khz) != XC_RESULT_SUCCESS)
+		goto fail;
+
+	ret = xc_SetSignalSource(priv, priv->rf_mode);
+	if (ret != XC_RESULT_SUCCESS) {
+		printk(KERN_ERR
+		       "xc4000: xc_SetSignalSource(%d) failed\n",
+		       priv->rf_mode);
+		goto fail;
+	} else {
+		u16	video_mode, audio_mode;
+		video_mode = XC4000_Standard[priv->video_standard].VideoMode;
+		audio_mode = XC4000_Standard[priv->video_standard].AudioMode;
+		if (type == DTV6 && priv->firm_version != 0x0102)
+			video_mode |= 0x0001;
+		ret = xc_SetTVStandard(priv, video_mode, audio_mode);
+		if (ret != XC_RESULT_SUCCESS) {
+			printk(KERN_ERR "xc4000: xc_SetTVStandard failed\n");
+			/* DJH - do not return when it fails... */
+			/* goto fail; */
+		}
+	}
+
+	if (priv->card_type == XC4000_CARD_WINFAST_CX88) {
+		if (xc_write_reg(priv, XREG_D_CODE, 0) == 0)
+			ret = 0;
+		if (xc_write_reg(priv, XREG_AMPLITUDE,
+				 (priv->firm_version == 0x0102 ? 132 : 134))
+		    != 0)
+			ret = -EREMOTEIO;
+		if (xc_write_reg(priv, XREG_SMOOTHEDCVBS, 1) != 0)
+			ret = -EREMOTEIO;
+		if (ret != 0) {
+			printk(KERN_ERR "xc4000: setting registers failed\n");
+			/* goto fail; */
+		}
+	}
+
+	xc_tune_channel(priv, priv->freq_hz);
+
+	ret = 0;
+
+fail:
+	mutex_unlock(&priv->lock);
+
+	return ret;
+}
+
+static int xc4000_set_analog_params(struct dvb_frontend *fe,
+	struct analog_parameters *params)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+	unsigned int type = 0;
+	int	ret = -EREMOTEIO;
+
+	if (params->mode == V4L2_TUNER_RADIO) {
+		dprintk(1, "%s() frequency=%d (in units of 62.5Hz)\n",
+			__func__, params->frequency);
+
+		mutex_lock(&priv->lock);
+
+		params->std = 0;
+		priv->freq_hz = params->frequency * 125L / 2;
+
+		if (audio_std & XC4000_AUDIO_STD_INPUT1) {
+			priv->video_standard = XC4000_FM_Radio_INPUT1;
+			type = FM | INPUT1;
+		} else {
+			priv->video_standard = XC4000_FM_Radio_INPUT2;
+			type = FM | INPUT2;
+		}
+
+		goto tune_channel;
+	}
+
+	dprintk(1, "%s() frequency=%d (in units of 62.5khz)\n",
+		__func__, params->frequency);
+
+	mutex_lock(&priv->lock);
+
+	/* params->frequency is in units of 62.5khz */
+	priv->freq_hz = params->frequency * 62500;
+
+	params->std &= V4L2_STD_ALL;
+	/* if std is not defined, choose one */
+	if (!params->std)
+		params->std = V4L2_STD_PAL_BG;
+
+	if (audio_std & XC4000_AUDIO_STD_MONO)
+		type = MONO;
+
+	if (params->std & V4L2_STD_MN) {
+		params->std = V4L2_STD_MN;
+		if (audio_std & XC4000_AUDIO_STD_MONO) {
+			priv->video_standard = XC4000_MN_NTSC_PAL_Mono;
+		} else if (audio_std & XC4000_AUDIO_STD_A2) {
+			params->std |= V4L2_STD_A2;
+			priv->video_standard = XC4000_MN_NTSC_PAL_A2;
+		} else {
+			params->std |= V4L2_STD_BTSC;
+			priv->video_standard = XC4000_MN_NTSC_PAL_BTSC;
+		}
+		goto tune_channel;
+	}
+
+	if (params->std & V4L2_STD_PAL_BG) {
+		params->std = V4L2_STD_PAL_BG;
+		if (audio_std & XC4000_AUDIO_STD_MONO) {
+			priv->video_standard = XC4000_BG_PAL_MONO;
+		} else if (!(audio_std & XC4000_AUDIO_STD_A2)) {
+			if (!(audio_std & XC4000_AUDIO_STD_B)) {
+				params->std |= V4L2_STD_NICAM_A;
+				priv->video_standard = XC4000_BG_PAL_NICAM;
+			} else {
+				params->std |= V4L2_STD_NICAM_B;
+				priv->video_standard = XC4000_BG_PAL_NICAM;
+			}
+		} else {
+			if (!(audio_std & XC4000_AUDIO_STD_B)) {
+				params->std |= V4L2_STD_A2_A;
+				priv->video_standard = XC4000_BG_PAL_A2;
+			} else {
+				params->std |= V4L2_STD_A2_B;
+				priv->video_standard = XC4000_BG_PAL_A2;
+			}
+		}
+		goto tune_channel;
+	}
+
+	if (params->std & V4L2_STD_PAL_I) {
+		/* default to NICAM audio standard */
+		params->std = V4L2_STD_PAL_I | V4L2_STD_NICAM;
+		if (audio_std & XC4000_AUDIO_STD_MONO) {
+			priv->video_standard = XC4000_I_PAL_NICAM_MONO;
+		} else {
+			priv->video_standard = XC4000_I_PAL_NICAM;
+		}
+		goto tune_channel;
+	}
+
+	if (params->std & V4L2_STD_PAL_DK) {
+		params->std = V4L2_STD_PAL_DK;
+		if (audio_std & XC4000_AUDIO_STD_MONO) {
+			priv->video_standard = XC4000_DK_PAL_MONO;
+		} else if (audio_std & XC4000_AUDIO_STD_A2) {
+			params->std |= V4L2_STD_A2;
+			priv->video_standard = XC4000_DK_PAL_A2;
+		} else {
+			params->std |= V4L2_STD_NICAM;
+			priv->video_standard = XC4000_DK_PAL_NICAM;
+		}
+		goto tune_channel;
+	}
+
+	if (params->std & V4L2_STD_SECAM_DK) {
+		/* default to A2 audio standard */
+		params->std = V4L2_STD_SECAM_DK | V4L2_STD_A2;
+		if (audio_std & XC4000_AUDIO_STD_L) {
+			type = 0;
+			priv->video_standard = XC4000_DK_SECAM_NICAM;
+		} else if (audio_std & XC4000_AUDIO_STD_MONO) {
+			priv->video_standard = XC4000_DK_SECAM_A2MONO;
+		} else if (audio_std & XC4000_AUDIO_STD_K3) {
+			params->std |= V4L2_STD_SECAM_K3;
+			priv->video_standard = XC4000_DK_SECAM_A2LDK3;
+		} else {
+			priv->video_standard = XC4000_DK_SECAM_A2DK1;
+		}
+		goto tune_channel;
+	}
+
+	if (params->std & V4L2_STD_SECAM_L) {
+		/* default to NICAM audio standard */
+		type = 0;
+		params->std = V4L2_STD_SECAM_L | V4L2_STD_NICAM;
+		priv->video_standard = XC4000_L_SECAM_NICAM;
+		goto tune_channel;
+	}
+
+	if (params->std & V4L2_STD_SECAM_LC) {
+		/* default to NICAM audio standard */
+		type = 0;
+		params->std = V4L2_STD_SECAM_LC | V4L2_STD_NICAM;
+		priv->video_standard = XC4000_LC_SECAM_NICAM;
+		goto tune_channel;
+	}
+
+tune_channel:
+	/* Fix me: it could be air. */
+	priv->rf_mode = XC_RF_MODE_CABLE;
+
+	if (check_firmware(fe, type, params->std,
+			   XC4000_Standard[priv->video_standard].int_freq)
+	    != XC_RESULT_SUCCESS) {
+		goto fail;
+	}
+
+	ret = xc_SetSignalSource(priv, priv->rf_mode);
+	if (ret != XC_RESULT_SUCCESS) {
+		printk(KERN_ERR
+		       "xc4000: xc_SetSignalSource(%d) failed\n",
+		       priv->rf_mode);
+		goto fail;
+	} else {
+		u16	video_mode, audio_mode;
+		video_mode = XC4000_Standard[priv->video_standard].VideoMode;
+		audio_mode = XC4000_Standard[priv->video_standard].AudioMode;
+		if (priv->video_standard < XC4000_BG_PAL_A2) {
+			if (0 /*type & NOGD*/)
+				video_mode &= 0xFF7F;
+		} else if (priv->video_standard < XC4000_I_PAL_NICAM) {
+			if (priv->card_type == XC4000_CARD_WINFAST_CX88 &&
+			    priv->firm_version == 0x0102)
+				video_mode &= 0xFEFF;
+			if (audio_std & XC4000_AUDIO_STD_B)
+				video_mode |= 0x0080;
+		}
+		ret = xc_SetTVStandard(priv, video_mode, audio_mode);
+		if (ret != XC_RESULT_SUCCESS) {
+			printk(KERN_ERR "xc4000: xc_SetTVStandard failed\n");
+			goto fail;
+		}
+	}
+
+	if (priv->card_type == XC4000_CARD_WINFAST_CX88) {
+		if (xc_write_reg(priv, XREG_D_CODE, 0) == 0)
+			ret = 0;
+		if (xc_write_reg(priv, XREG_AMPLITUDE, 1) != 0)
+			ret = -EREMOTEIO;
+		if (xc_write_reg(priv, XREG_SMOOTHEDCVBS, 1) != 0)
+			ret = -EREMOTEIO;
+		if (ret != 0) {
+			printk(KERN_ERR "xc4000: setting registers failed\n");
+			goto fail;
+		}
+	}
+
+	xc_tune_channel(priv, priv->freq_hz);
+
+	ret = 0;
+
+fail:
+	mutex_unlock(&priv->lock);
+
+	return ret;
+}
+
+static int xc4000_get_frequency(struct dvb_frontend *fe, u32 *freq)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+
+	*freq = priv->freq_hz;
+
+	if (debug) {
+		mutex_lock(&priv->lock);
+		if ((priv->cur_fw.type
+		     & (BASE | FM | DTV6 | DTV7 | DTV78 | DTV8)) == BASE) {
+			u16	snr = 0;
+			if (xc4000_readreg(priv, XREG_SNR, &snr) == 0) {
+				mutex_unlock(&priv->lock);
+				dprintk(1, "%s() freq = %u, SNR = %d\n",
+					__func__, *freq, snr);
+				return 0;
+			}
+		}
+		mutex_unlock(&priv->lock);
+	}
+
+	dprintk(1, "%s()\n", __func__);
+
+	return 0;
+}
+
+static int xc4000_get_bandwidth(struct dvb_frontend *fe, u32 *bw)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+	dprintk(1, "%s()\n", __func__);
+
+	*bw = priv->bandwidth;
+	return 0;
+}
+
+static int xc4000_get_status(struct dvb_frontend *fe, u32 *status)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+	u16	lock_status = 0;
+
+	mutex_lock(&priv->lock);
+
+	if (priv->cur_fw.type & BASE)
+		xc_get_lock_status(priv, &lock_status);
+
+	*status = (lock_status == 1 ?
+		   TUNER_STATUS_LOCKED | TUNER_STATUS_STEREO : 0);
+	if (priv->cur_fw.type & (DTV6 | DTV7 | DTV78 | DTV8))
+		*status &= (~TUNER_STATUS_STEREO);
+
+	mutex_unlock(&priv->lock);
+
+	dprintk(2, "%s() lock_status = %d\n", __func__, lock_status);
+
+	return 0;
+}
+
+static int xc4000_sleep(struct dvb_frontend *fe)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+	int	ret = XC_RESULT_SUCCESS;
+
+	dprintk(1, "%s()\n", __func__);
+
+	mutex_lock(&priv->lock);
+
+	/* Avoid firmware reload on slow devices */
+	if ((no_poweroff == 2 ||
+	     (no_poweroff == 0 &&
+	      priv->card_type != XC4000_CARD_WINFAST_CX88)) &&
+	    (priv->cur_fw.type & BASE) != 0) {
+		/* force reset and firmware reload */
+		priv->cur_fw.type = XC_POWERED_DOWN;
+
+		if (xc_write_reg(priv, XREG_POWER_DOWN, 0)
+		    != XC_RESULT_SUCCESS) {
+			printk(KERN_ERR
+			       "xc4000: %s() unable to shutdown tuner\n",
+			       __func__);
+			ret = -EREMOTEIO;
+		}
+		xc_wait(20);
+	}
+
+	mutex_unlock(&priv->lock);
+
+	return ret;
+}
+
+static int xc4000_init(struct dvb_frontend *fe)
+{
+	dprintk(1, "%s()\n", __func__);
+
+	return 0;
+}
+
+static int xc4000_release(struct dvb_frontend *fe)
+{
+	struct xc4000_priv *priv = fe->tuner_priv;
+
+	dprintk(1, "%s()\n", __func__);
+
+	mutex_lock(&xc4000_list_mutex);
+
+	if (priv)
+		hybrid_tuner_release_state(priv);
+
+	mutex_unlock(&xc4000_list_mutex);
+
+	fe->tuner_priv = NULL;
+
+	return 0;
+}
+
+static const struct dvb_tuner_ops xc4000_tuner_ops = {
+	.info = {
+		.name           = "Xceive XC4000",
+		.frequency_min  =    1000000,
+		.frequency_max  = 1023000000,
+		.frequency_step =      50000,
+	},
+
+	.release	   = xc4000_release,
+	.init		   = xc4000_init,
+	.sleep		   = xc4000_sleep,
+
+	.set_params	   = xc4000_set_params,
+	.set_analog_params = xc4000_set_analog_params,
+	.get_frequency	   = xc4000_get_frequency,
+	.get_bandwidth	   = xc4000_get_bandwidth,
+	.get_status	   = xc4000_get_status
+};
+
+struct dvb_frontend *xc4000_attach(struct dvb_frontend *fe,
+				   struct i2c_adapter *i2c,
+				   struct xc4000_config *cfg)
+{
+	struct xc4000_priv *priv = NULL;
+	int	instance;
+	u16	id = 0;
+
+	if (cfg->card_type != XC4000_CARD_GENERIC) {
+		if (cfg->card_type == XC4000_CARD_WINFAST_CX88) {
+			cfg->i2c_address = 0x61;
+			cfg->if_khz = 4560;
+		} else {			/* default to PCTV 340E */
+			cfg->i2c_address = 0x61;
+			cfg->if_khz = 5400;
+		}
+	}
+
+	dprintk(1, "%s(%d-%04x)\n", __func__,
+		i2c ? i2c_adapter_id(i2c) : -1,
+		cfg ? cfg->i2c_address : -1);
+
+	mutex_lock(&xc4000_list_mutex);
+
+	instance = hybrid_tuner_request_state(struct xc4000_priv, priv,
+					      hybrid_tuner_instance_list,
+					      i2c, cfg->i2c_address, "xc4000");
+	if (cfg->card_type != XC4000_CARD_GENERIC)
+		priv->card_type = cfg->card_type;
+	switch (instance) {
+	case 0:
+		goto fail;
+		break;
+	case 1:
+		/* new tuner instance */
+		priv->bandwidth = BANDWIDTH_6_MHZ;
+		mutex_init(&priv->lock);
+		fe->tuner_priv = priv;
+		break;
+	default:
+		/* existing tuner instance */
+		fe->tuner_priv = priv;
+		break;
+	}
+
+	if (cfg->if_khz != 0) {
+		/* If the IF hasn't been set yet, use the value provided by
+		   the caller (occurs in hybrid devices where the analog
+		   call to xc4000_attach occurs before the digital side) */
+		priv->if_khz = cfg->if_khz;
+	}
+
+	/* Check if firmware has been loaded. It is possible that another
+	   instance of the driver has loaded the firmware.
+	 */
+
+	if (instance == 1) {
+		if (xc4000_readreg(priv, XREG_PRODUCT_ID, &id)
+		    != XC_RESULT_SUCCESS)
+			goto fail;
+	} else {
+		id = ((priv->cur_fw.type & BASE) != 0 ?
+		      priv->hwmodel : XC_PRODUCT_ID_FW_NOT_LOADED);
+	}
+
+	switch (id) {
+	case XC_PRODUCT_ID_XC4000:
+	case XC_PRODUCT_ID_XC4100:
+		printk(KERN_INFO
+			"xc4000: Successfully identified at address 0x%02x\n",
+			cfg->i2c_address);
+		printk(KERN_INFO
+			"xc4000: Firmware has been loaded previously\n");
+		break;
+	case XC_PRODUCT_ID_FW_NOT_LOADED:
+		printk(KERN_INFO
+			"xc4000: Successfully identified at address 0x%02x\n",
+			cfg->i2c_address);
+		printk(KERN_INFO
+			"xc4000: Firmware has not been loaded previously\n");
+		break;
+	default:
+		printk(KERN_ERR
+			"xc4000: Device not found at addr 0x%02x (0x%x)\n",
+			cfg->i2c_address, id);
+		goto fail;
+	}
+
+	mutex_unlock(&xc4000_list_mutex);
+
+	memcpy(&fe->ops.tuner_ops, &xc4000_tuner_ops,
+		sizeof(struct dvb_tuner_ops));
+
+	if (instance == 1) {
+		int	ret;
+		mutex_lock(&priv->lock);
+		ret = xc4000_fwupload(fe);
+		mutex_unlock(&priv->lock);
+		if (ret != XC_RESULT_SUCCESS)
+			goto fail2;
+	}
+
+	return fe;
+fail:
+	mutex_unlock(&xc4000_list_mutex);
+fail2:
+	xc4000_release(fe);
+	return NULL;
+}
+EXPORT_SYMBOL(xc4000_attach);
+
+MODULE_AUTHOR("Steven Toth, Davide Ferri");
+MODULE_DESCRIPTION("Xceive xc4000 silicon tuner driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/media/common/tuners/xc4000.h b/drivers/media/common/tuners/xc4000.h
new file mode 100644
index 0000000..d560d01
--- /dev/null
+++ b/drivers/media/common/tuners/xc4000.h
@@ -0,0 +1,66 @@
+/*
+ *  Driver for Xceive XC4000 "QAM/8VSB single chip tuner"
+ *
+ *  Copyright (c) 2007 Steven Toth <stoth@linuxtv.org>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __XC4000_H__
+#define __XC4000_H__
+
+#include <linux/firmware.h>
+
+struct dvb_frontend;
+struct i2c_adapter;
+
+#define XC4000_CARD_GENERIC		0
+#define XC4000_CARD_PCTV_340E		1
+#define XC4000_CARD_WINFAST_CX88	2
+
+struct xc4000_config {
+	u8	card_type;	/* if card type is not generic, all other */
+	u8	i2c_address;	/* parameters are automatically set */
+	u32	if_khz;
+};
+
+/* xc4000 callback command */
+#define XC4000_TUNER_RESET		0
+
+/* For each bridge framework, when it attaches either analog or digital,
+ * it has to store a reference back to its _core equivalent structure,
+ * so that it can service the hardware by steering gpio's etc.
+ * Each bridge implementation is different so cast devptr accordingly.
+ * The xc4000 driver cares not for this value, other than ensuring
+ * it's passed back to a bridge during tuner_callback().
+ */
+
+#if defined(CONFIG_MEDIA_TUNER_XC4000) || \
+    (defined(CONFIG_MEDIA_TUNER_XC4000_MODULE) && defined(MODULE))
+extern struct dvb_frontend *xc4000_attach(struct dvb_frontend *fe,
+					  struct i2c_adapter *i2c,
+					  struct xc4000_config *cfg);
+#else
+static inline struct dvb_frontend *xc4000_attach(struct dvb_frontend *fe,
+						 struct i2c_adapter *i2c,
+						 struct xc4000_config *cfg)
+{
+	printk(KERN_WARNING "%s: driver disabled by Kconfig\n", __func__);
+	return NULL;
+}
+#endif
+
+#endif
diff --git a/drivers/media/dvb/dvb-usb/dib0700_devices.c b/drivers/media/dvb/dvb-usb/dib0700_devices.c
index c519ad5..a5212a5 100644
--- a/drivers/media/dvb/dvb-usb/dib0700_devices.c
+++ b/drivers/media/dvb/dvb-usb/dib0700_devices.c
@@ -17,6 +17,7 @@
 #include "mt2266.h"
 #include "tuner-xc2028.h"
 #include "xc5000.h"
+#include "xc4000.h"
 #include "s5h1411.h"
 #include "dib0070.h"
 #include "dib0090.h"
@@ -2655,6 +2656,153 @@ static int xc5000_tuner_attach(struct dvb_usb_adapter *adap)
 		== NULL ? -ENODEV : 0;
 }
 
+static int dib0700_xc4000_tuner_callback(void *priv, int component,
+					 int command, int arg)
+{
+	struct dvb_usb_adapter *adap = priv;
+
+	if (command == XC4000_TUNER_RESET) {
+		/* Reset the tuner */
+		dib7000p_set_gpio(adap->fe, 8, 0, 0);
+		msleep(10);
+		dib7000p_set_gpio(adap->fe, 8, 0, 1);
+	} else {
+		err("xc4000: unknown tuner callback command: %d\n", command);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static struct dibx000_agc_config stk7700p_7000p_xc4000_agc_config = {
+	.band_caps = BAND_UHF | BAND_VHF,
+	.setup = 0x64,
+	.inv_gain = 0x02c8,
+	.time_stabiliz = 0x15,
+	.alpha_level = 0x00,
+	.thlock = 0x76,
+	.wbd_inv = 0x01,
+	.wbd_ref = 0x0b33,
+	.wbd_sel = 0x00,
+	.wbd_alpha = 0x02,
+	.agc1_max = 0x00,
+	.agc1_min = 0x00,
+	.agc2_max = 0x9b26,
+	.agc2_min = 0x26ca,
+	.agc1_pt1 = 0x00,
+	.agc1_pt2 = 0x00,
+	.agc1_pt3 = 0x00,
+	.agc1_slope1 = 0x00,
+	.agc1_slope2 = 0x00,
+	.agc2_pt1 = 0x00,
+	.agc2_pt2 = 0x80,
+	.agc2_slope1 = 0x1d,
+	.agc2_slope2 = 0x1d,
+	.alpha_mant = 0x11,
+	.alpha_exp = 0x1b,
+	.beta_mant = 0x17,
+	.beta_exp = 0x33,
+	.perform_agc_softsplit = 0x00,
+};
+
+static struct dibx000_bandwidth_config stk7700p_xc4000_pll_config = {
+	60000, 30000, // internal, sampling
+	1, 8, 3, 1, 0, // pll_cfg: prediv, ratio, range, reset, bypass
+	0, 0, 1, 1, 0, // misc: refdiv, bypclk_div, IO_CLK_en_core, ADClkSrc, modulo
+	(3 << 14) | (1 << 12) | (524 << 0), // sad_cfg: refsel, sel, freq_15k
+	39370534, // ifreq
+	20452225, // timf
+	30000000, // xtal
+};
+
+/* FIXME: none of these inputs are validated yet */
+static struct dib7000p_config pctv_340e_config = {
+	.output_mpeg2_in_188_bytes = 1,
+
+	.agc_config_count = 1,
+	.agc = &stk7700p_7000p_xc4000_agc_config,
+	.bw  = &stk7700p_xc4000_pll_config,
+
+	.gpio_dir = DIB7000M_GPIO_DEFAULT_DIRECTIONS,
+	.gpio_val = DIB7000M_GPIO_DEFAULT_VALUES,
+	.gpio_pwm_pos = DIB7000M_GPIO_DEFAULT_PWM_POS,
+};
+
+/* PCTV 340e GPIOs map:
+   dib0700:
+   GPIO2  - CX25843 sleep
+   GPIO3  - CS5340 reset
+   GPIO5  - IRD
+   GPIO6  - Power Supply
+   GPIO8  - LNA (1=off 0=on)
+   GPIO10 - CX25843 reset
+   dib7000:
+   GPIO8  - xc4000 reset
+ */
+static int pctv340e_frontend_attach(struct dvb_usb_adapter *adap)
+{
+	struct dib0700_state *st = adap->dev->priv;
+
+	/* Power Supply on */
+	dib0700_set_gpio(adap->dev, GPIO6,  GPIO_OUT, 0);
+	msleep(50);
+	dib0700_set_gpio(adap->dev, GPIO6,  GPIO_OUT, 1);
+	msleep(100); /* Allow power supply to settle before probing */
+
+	/* cx25843 reset */
+	dib0700_set_gpio(adap->dev, GPIO10,  GPIO_OUT, 0);
+	msleep(1); /* cx25843 datasheet say 350us required */
+	dib0700_set_gpio(adap->dev, GPIO10,  GPIO_OUT, 1);
+
+	/* LNA off for now */
+	dib0700_set_gpio(adap->dev, GPIO8,  GPIO_OUT, 1);
+
+	/* Put the CX25843 to sleep for now since we're in digital mode */
+	dib0700_set_gpio(adap->dev, GPIO2, GPIO_OUT, 1);
+
+	/* FIXME: not verified yet */
+	dib0700_ctrl_clock(adap->dev, 72, 1);
+
+	msleep(500);
+
+	if (dib7000pc_detection(&adap->dev->i2c_adap) == 0) {
+		/* Demodulator not found for some reason? */
+		return -ENODEV;
+	}
+
+	adap->fe = dvb_attach(dib7000p_attach, &adap->dev->i2c_adap, 0x12,
+			      &pctv_340e_config);
+	st->is_dib7000pc = 1;
+
+	return adap->fe == NULL ? -ENODEV : 0;
+}
+
+
+static struct xc4000_config dib7000p_xc4000_tunerconfig = {
+	.i2c_address      = 0x61,
+	.if_khz           = 5400,
+};
+
+static int xc4000_tuner_attach(struct dvb_usb_adapter *adap)
+{
+	struct i2c_adapter *tun_i2c;
+
+	/* The xc4000 is not on the main i2c bus */
+	tun_i2c = dib7000p_get_i2c_master(adap->fe,
+					  DIBX000_I2C_INTERFACE_TUNER, 1);
+	if (tun_i2c == NULL) {
+		printk("Could not reach tuner i2c bus\n");
+		return 0;
+	}
+
+	/* Setup the reset callback */
+	adap->fe->callback = dib0700_xc4000_tuner_callback;
+
+	return dvb_attach(xc4000_attach, adap->fe, tun_i2c,
+			  &dib7000p_xc4000_tunerconfig)
+		== NULL ? -ENODEV : 0;
+}
+
 static struct lgdt3305_config hcw_lgdt3305_config = {
 	.i2c_addr           = 0x0e,
 	.mpeg_mode          = LGDT3305_MPEG_PARALLEL,
@@ -2802,6 +2950,8 @@ struct usb_device_id dib0700_usb_id_table[] = {
 	{ USB_DEVICE(USB_VID_DIBCOM,    USB_PID_DIBCOM_TFE7090PVR) },
 	{ USB_DEVICE(USB_VID_TECHNISAT, USB_PID_TECHNISAT_AIRSTAR_TELESTICK_2) },
 /* 75 */{ USB_DEVICE(USB_VID_MEDION,    USB_PID_CREATIX_CTX1921) },
+	{ USB_DEVICE(USB_VID_PINNACLE,  USB_PID_PINNACLE_PCTV340E) },
+	{ USB_DEVICE(USB_VID_PINNACLE,  USB_PID_PINNACLE_PCTV340E_SE) },
 	{ 0 }		/* Terminating entry */
 };
 MODULE_DEVICE_TABLE(usb, dib0700_usb_id_table);
@@ -3772,6 +3922,41 @@ struct dvb_usb_device_properties dib0700_devices[] = {
 					    RC_TYPE_NEC,
 			.change_protocol  = dib0700_change_protocol,
 		},
+	}, { DIB0700_DEFAULT_DEVICE_PROPERTIES,
+		.num_adapters = 1,
+		.adapter = {
+			{
+				.frontend_attach  = pctv340e_frontend_attach,
+				.tuner_attach     = xc4000_tuner_attach,
+
+				DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
+
+				.size_of_priv = sizeof(struct
+						dib0700_adapter_state),
+			},
+		},
+
+		.num_device_descs = 2,
+		.devices = {
+			{   "Pinnacle PCTV 340e HD Pro USB Stick",
+				{ &dib0700_usb_id_table[76], NULL },
+				{ NULL },
+			},
+			{   "Pinnacle PCTV Hybrid Stick Solo",
+				{ &dib0700_usb_id_table[77], NULL },
+				{ NULL },
+			},
+		},
+		.rc.core = {
+			.rc_interval      = DEFAULT_RC_INTERVAL,
+			.rc_codes         = RC_MAP_DIB0700_RC5_TABLE,
+			.module_name	  = "dib0700",
+			.rc_query         = dib0700_rc_query_old_firmware,
+			.allowed_protos   = RC_TYPE_RC5 |
+					    RC_TYPE_RC6 |
+					    RC_TYPE_NEC,
+			.change_protocol  = dib0700_change_protocol,
+		},
 	},
 };
 
diff --git a/drivers/media/dvb/dvb-usb/dvb-usb-ids.h b/drivers/media/dvb/dvb-usb/dvb-usb-ids.h
index 21b1549..20e4788 100644
--- a/drivers/media/dvb/dvb-usb/dvb-usb-ids.h
+++ b/drivers/media/dvb/dvb-usb/dvb-usb-ids.h
@@ -230,6 +230,8 @@
 #define USB_PID_PINNACLE_PCTV310E			0x3211
 #define USB_PID_PINNACLE_PCTV801E			0x023a
 #define USB_PID_PINNACLE_PCTV801E_SE			0x023b
+#define USB_PID_PINNACLE_PCTV340E			0x023d
+#define USB_PID_PINNACLE_PCTV340E_SE			0x023e
 #define USB_PID_PINNACLE_PCTV73A			0x0243
 #define USB_PID_PINNACLE_PCTV73ESE			0x0245
 #define USB_PID_PINNACLE_PCTV74E			0x0246
diff --git a/drivers/media/dvb/frontends/dib7000p.c b/drivers/media/dvb/frontends/dib7000p.c
index 0c9f40c..a64a538 100644
--- a/drivers/media/dvb/frontends/dib7000p.c
+++ b/drivers/media/dvb/frontends/dib7000p.c
@@ -2336,6 +2336,11 @@ struct dvb_frontend *dib7000p_attach(struct i2c_adapter *i2c_adap, u8 i2c_addr,
 		request_firmware() will hit an OOPS (this should be moved somewhere
 		more common) */
 
+	/* FIXME: make sure the dev.parent field is initialized, or else
+	   request_firmware() will hit an OOPS (this should be moved somewhere
+	   more common) */
+	st->i2c_master.gated_tuner_i2c_adap.dev.parent = i2c_adap->dev.parent;
+
 	dibx000_init_i2c_master(&st->i2c_master, DIB7000P, st->i2c_adap, st->i2c_addr);
 
 	/* init 7090 tuner adapter */
diff --git a/drivers/media/video/tuner-core.c b/drivers/media/video/tuner-core.c
index 9363ed9..417c6d1 100644
--- a/drivers/media/video/tuner-core.c
+++ b/drivers/media/video/tuner-core.c
@@ -39,6 +39,7 @@
 #include "tda9887.h"
 #include "xc5000.h"
 #include "tda18271.h"
+#include "xc4000.h"
 
 #define UNSET (-1U)
 
@@ -391,6 +392,19 @@ static void set_type(struct i2c_client *c, unsigned int type,
 		tune_now = 0;
 		break;
 	}
+	case TUNER_XC4000:
+	{
+		struct xc4000_config xc4000_cfg = {
+			.i2c_address	  = t->i2c->addr,
+			/* if_khz will be set when the digital dvb_attach() occurs */
+			.if_khz	  = 0,
+		};
+		if (!dvb_attach(xc4000_attach,
+				&t->fe, t->i2c->adapter, &xc4000_cfg))
+			goto attach_failed;
+		tune_now = 0;
+		break;
+	}
 	default:
 		if (!dvb_attach(simple_tuner_attach, &t->fe,
 				t->i2c->adapter, t->i2c->addr, t->type))
diff --git a/include/media/tuner.h b/include/media/tuner.h
index 963e334..89c290b 100644
--- a/include/media/tuner.h
+++ b/include/media/tuner.h
@@ -127,6 +127,8 @@
 #define TUNER_PHILIPS_FMD1216MEX_MK3	78
 #define TUNER_PHILIPS_FM1216MK5		79
 #define TUNER_PHILIPS_FQ1216LME_MK3	80	/* Active loopthrough, no FM */
+#define TUNER_XC4000			81	/* Xceive Silicon Tuner */
+
 #define TUNER_PARTSNIC_PTI_5NF05	81
 #define TUNER_PHILIPS_CU1216L           82
 #define TUNER_NXP_TDA18271		83