* 290e locking issue @ 2012-01-25 22:16 Claus Olesen 2012-01-26 9:07 ` Antti Palosaari 0 siblings, 1 reply; 9+ messages in thread From: Claus Olesen @ 2012-01-25 22:16 UTC (permalink / raw) To: linux-media just got 3.2.1-3.fc16.i686.PAE the issue that the driver had to be removed for the 290e to work after a replug is gone. the issue that a usb mem stick cannot be mounted while the 290e is plugged in still lingers. one workaround is to unplug the 290e and wait a little (no need to also remove the driver). ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: 290e locking issue 2012-01-25 22:16 290e locking issue Claus Olesen @ 2012-01-26 9:07 ` Antti Palosaari 2012-01-26 11:46 ` Claus Olesen 0 siblings, 1 reply; 9+ messages in thread From: Antti Palosaari @ 2012-01-26 9:07 UTC (permalink / raw) To: Claus Olesen; +Cc: linux-media On 01/26/2012 12:16 AM, Claus Olesen wrote: > just got 3.2.1-3.fc16.i686.PAE > the issue that the driver had to be removed for the 290e to work after > a replug is gone. > the issue that a usb mem stick cannot be mounted while the 290e is > plugged in still lingers. > one workaround is to unplug the 290e and wait a little (no need to > also remove the driver). What it prints to the system log? Use tail -f /var/log/messages or dmesg. Antti -- http://palosaari.fi/ ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: 290e locking issue 2012-01-26 9:07 ` Antti Palosaari @ 2012-01-26 11:46 ` Claus Olesen 2012-01-26 11:58 ` Antti Palosaari 0 siblings, 1 reply; 9+ messages in thread From: Claus Olesen @ 2012-01-26 11:46 UTC (permalink / raw) To: Antti Palosaari; +Cc: linux-media the dmesg output from inplug of 290e until usb mem stick mount timeout with a cut marked "--- cut similar ---" between mount and timeout for less output is >inplug 290e [ 112.367345] usb 2-3: new high-speed USB device number 2 using ehci_hcd [ 112.482773] usb 2-3: New USB device found, idVendor=2013, idProduct=024f [ 112.482783] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 112.482790] usb 2-3: Product: PCTV 290e [ 112.482796] usb 2-3: Manufacturer: PCTV Systems [ 112.482801] usb 2-3: SerialNumber: 00000006VEJQ [ 112.988850] em28xx: New device PCTV Systems PCTV 290e @ 480 Mbps (2013:024f, interface 0, class 0) [ 112.988929] em28xx #0: chip ID is em28174 [ 113.284694] em28xx #0: Identified as PCTV nanoStick T2 290e (card=78) [ 113.340323] Registered IR keymap rc-pinnacle-pctv-hd [ 113.340594] input: em28xx IR (em28xx #0) as /devices/pci0000:00/0000:00:1d.7/usb2/2-3/rc/rc1/input19 [ 113.341677] rc1: em28xx IR (em28xx #0) as /devices/pci0000:00/0000:00:1d.7/usb2/2-3/rc/rc1 [ 113.342411] em28xx #0: v4l2 driver version 0.1.3 [ 113.348855] em28xx #0: V4L2 video device registered as video1 [ 113.350562] usbcore: registered new interface driver em28xx [ 113.350568] em28xx driver loaded [ 113.480057] tda18271 17-0060: creating new instance [ 113.485221] TDA18271HD/C2 detected @ 17-0060 [ 113.724218] tda18271 17-0060: attaching existing instance [ 113.724227] DVB: registering new adapter (em28xx #0) [ 113.724235] DVB: registering adapter 0 frontend 0 (Sony CXD2820R (DVB-T/T2))... [ 113.724763] DVB: registering adapter 0 frontend 1 (Sony CXD2820R (DVB-C))... [ 113.728614] em28xx #0: Successfully loaded em28xx-dvb [ 113.728617] Em28xx: Initialized (Em28xx dvb Extension) extension >inplug usb mem stick [ 136.177341] usb 2-1: new high-speed USB device number 3 using ehci_hcd [ 136.308531] usb 2-1: New USB device found, idVendor=0bda, idProduct=0120 [ 136.308541] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 136.308548] usb 2-1: Product: USB2.0-CRW [ 136.308554] usb 2-1: Manufacturer: Generic [ 136.308559] usb 2-1: SerialNumber: 20060413092100000 [ 136.630379] Initializing USB Mass Storage driver... [ 136.630764] scsi6 : usb-storage 2-1:1.0 [ 136.631270] usbcore: registered new interface driver usb-storage [ 136.631275] USB Mass Storage support registered. [ 137.636863] scsi 6:0:0:0: Direct-Access Generic- Card Reader 1.00 PQ: 0 ANSI: 0 CCS [ 137.639519] sd 6:0:0:0: Attached scsi generic sg3 type 0 [ 138.446467] sd 6:0:0:0: [sdc] 15661056 512-byte logical blocks: (8.01 GB/7.46 GiB) [ 138.447282] sd 6:0:0:0: [sdc] Write Protect is off [ 138.447291] sd 6:0:0:0: [sdc] Mode Sense: 03 00 00 00 [ 138.448138] sd 6:0:0:0: [sdc] No Caching mode page present [ 138.448147] sd 6:0:0:0: [sdc] Assuming drive cache: write through [ 138.451639] sd 6:0:0:0: [sdc] No Caching mode page present [ 138.451647] sd 6:0:0:0: [sdc] Assuming drive cache: write through [ 138.452729] sdc: sdc1 >mount usb mem stick sdc1 [ 168.838133] usb 2-1: reset high-speed USB device number 3 using ehci_hcd [ 168.959139] sd 6:0:0:0: [sdc] No Caching mode page present [ 168.959150] sd 6:0:0:0: [sdc] Assuming drive cache: write through [ 168.959159] sd 6:0:0:0: [sdc] Attached SCSI removable disk [ 199.878136] usb 2-1: reset high-speed USB device number 3 using ehci_hcd [ 199.998075] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 199.998082] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 199.998087] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 199.998094] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 80 00 00 08 00 [ 199.998106] end_request: I/O error, dev sdc, sector 15660928 [ 199.998110] Buffer I/O error on device sdc, logical block 1957616 [ 199.999455] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 199.999460] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 199.999465] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 199.999471] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 80 00 00 08 00 [ 199.999480] end_request: I/O error, dev sdc, sector 15660928 [ 199.999484] Buffer I/O error on device sdc, logical block 1957616 [ 200.000570] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.000573] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.000576] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.000580] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 80 00 00 08 00 [ 200.000586] end_request: I/O error, dev sdc, sector 15660928 [ 200.000589] Buffer I/O error on device sdc1, logical block 1956592 [ 200.001696] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.001701] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.001705] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.001711] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 f0 00 00 08 00 [ 200.001721] end_request: I/O error, dev sdc, sector 15661040 [ 200.001724] Buffer I/O error on device sdc, logical block 1957630 [ 200.002819] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.002824] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.002829] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.002835] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 80 00 00 08 00 [ 200.002844] end_request: I/O error, dev sdc, sector 15660928 [ 200.002848] Buffer I/O error on device sdc1, logical block 1956592 [ 200.003945] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.003950] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.003955] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.003961] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 f0 00 00 08 00 [ 200.003970] end_request: I/O error, dev sdc, sector 15661040 [ 200.003973] Buffer I/O error on device sdc, logical block 1957630 [ 200.031199] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.031204] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.031209] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.031215] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 f0 00 00 08 00 [ 200.031225] end_request: I/O error, dev sdc, sector 15661040 [ 200.031229] Buffer I/O error on device sdc1, logical block 1956606 [ 200.032322] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.032327] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.032331] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.032337] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 200.032347] end_request: I/O error, dev sdc, sector 0 [ 200.032350] Buffer I/O error on device sdc, logical block 0 [ 200.033448] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.033452] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.033457] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.033463] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 f0 00 00 08 00 [ 200.033472] end_request: I/O error, dev sdc, sector 15661040 [ 200.033476] Buffer I/O error on device sdc1, logical block 1956606 [ 200.034603] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.034612] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.034621] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.034633] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 200.034652] end_request: I/O error, dev sdc, sector 0 [ 200.034658] Buffer I/O error on device sdc, logical block 0 [ 200.035709] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.035719] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.035728] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.035740] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 08 00 [ 200.035761] end_request: I/O error, dev sdc, sector 8192 [ 200.036837] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.036846] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.036855] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.036867] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 08 00 00 08 00 [ 200.036886] end_request: I/O error, dev sdc, sector 8 [ 200.037961] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.037970] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.037979] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.037991] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 08 00 [ 200.038027] end_request: I/O error, dev sdc, sector 8192 [ 200.039091] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.039101] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.039110] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.039123] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 f8 00 00 01 00 [ 200.039142] end_request: I/O error, dev sdc, sector 15661048 [ 200.040209] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 200.040218] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 200.040227] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 200.040239] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 08 00 00 08 00 [ 200.040259] end_request: I/O error, dev sdc, sector 8200 [ 230.854039] usb 2-1: reset high-speed USB device number 3 using ehci_hcd [ 230.974172] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 230.974178] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 230.974184] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 230.974191] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 f8 00 00 01 00 [ 230.974202] end_request: I/O error, dev sdc, sector 15661048 [ 230.974206] quiet_error: 5 callbacks suppressed [ 230.974210] Buffer I/O error on device sdc, logical block 1957631 --- cut similar --- [ 478.279628] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 478.279634] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 478.279639] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 478.279645] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 02 00 00 02 00 [ 478.279656] end_request: I/O error, dev sdc, sector 8194 [ 478.279675] EXT4-fs (sdc1): unable to read superblock [ 478.288033] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 478.288045] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 478.288056] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 478.288068] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 40 00 00 02 00 [ 478.288090] end_request: I/O error, dev sdc, sector 8256 [ 478.288124] isofs_fill_super: bread failed, dev=sdc1, iso_blknum=16, block=32 [ 478.342498] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 478.342504] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 478.342510] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 478.342517] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 01 00 [ 478.342528] end_request: I/O error, dev sdc, sector 8192 [ 478.342545] FAT-fs (sdc1): unable to read boot sector On Thu, Jan 26, 2012 at 10:07 AM, Antti Palosaari <crope@iki.fi> wrote: > On 01/26/2012 12:16 AM, Claus Olesen wrote: >> >> just got 3.2.1-3.fc16.i686.PAE >> the issue that the driver had to be removed for the 290e to work after >> a replug is gone. >> the issue that a usb mem stick cannot be mounted while the 290e is >> plugged in still lingers. >> one workaround is to unplug the 290e and wait a little (no need to >> also remove the driver). > > > What it prints to the system log? Use tail -f /var/log/messages or dmesg. > > > Antti > -- > http://palosaari.fi/ ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: 290e locking issue 2012-01-26 11:46 ` Claus Olesen @ 2012-01-26 11:58 ` Antti Palosaari 2012-01-26 15:18 ` Devin Heitmueller 2012-01-26 17:09 ` Claus Olesen 0 siblings, 2 replies; 9+ messages in thread From: Antti Palosaari @ 2012-01-26 11:58 UTC (permalink / raw) To: Claus Olesen; +Cc: linux-media On 01/26/2012 01:46 PM, Claus Olesen wrote: > the dmesg output from inplug of 290e until usb mem stick mount timeout > with a cut marked "--- cut similar ---" between mount and timeout for > less output is I think it is maybe some incapability of em28xx driver. Maybe it could be something to do with USB HCI too... Could you test latest drivers using media_build.git ? > >> inplug 290e > [ 112.367345] usb 2-3: new high-speed USB device number 2 using ehci_hcd > [ 112.482773] usb 2-3: New USB device found, idVendor=2013, idProduct=024f > [ 112.482783] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 > [ 112.482790] usb 2-3: Product: PCTV 290e > [ 112.482796] usb 2-3: Manufacturer: PCTV Systems > [ 112.482801] usb 2-3: SerialNumber: 00000006VEJQ > [ 112.988850] em28xx: New device PCTV Systems PCTV 290e @ 480 Mbps > (2013:024f, interface 0, class 0) > [ 112.988929] em28xx #0: chip ID is em28174 > [ 113.284694] em28xx #0: Identified as PCTV nanoStick T2 290e (card=78) > [ 113.340323] Registered IR keymap rc-pinnacle-pctv-hd > [ 113.340594] input: em28xx IR (em28xx #0) as > /devices/pci0000:00/0000:00:1d.7/usb2/2-3/rc/rc1/input19 > [ 113.341677] rc1: em28xx IR (em28xx #0) as > /devices/pci0000:00/0000:00:1d.7/usb2/2-3/rc/rc1 > [ 113.342411] em28xx #0: v4l2 driver version 0.1.3 > [ 113.348855] em28xx #0: V4L2 video device registered as video1 > [ 113.350562] usbcore: registered new interface driver em28xx > [ 113.350568] em28xx driver loaded > [ 113.480057] tda18271 17-0060: creating new instance > [ 113.485221] TDA18271HD/C2 detected @ 17-0060 > [ 113.724218] tda18271 17-0060: attaching existing instance > [ 113.724227] DVB: registering new adapter (em28xx #0) > [ 113.724235] DVB: registering adapter 0 frontend 0 (Sony CXD2820R > (DVB-T/T2))... > [ 113.724763] DVB: registering adapter 0 frontend 1 (Sony CXD2820R (DVB-C))... > [ 113.728614] em28xx #0: Successfully loaded em28xx-dvb > [ 113.728617] Em28xx: Initialized (Em28xx dvb Extension) extension >> inplug usb mem stick > [ 136.177341] usb 2-1: new high-speed USB device number 3 using ehci_hcd > [ 136.308531] usb 2-1: New USB device found, idVendor=0bda, idProduct=0120 > [ 136.308541] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 > [ 136.308548] usb 2-1: Product: USB2.0-CRW > [ 136.308554] usb 2-1: Manufacturer: Generic > [ 136.308559] usb 2-1: SerialNumber: 20060413092100000 > [ 136.630379] Initializing USB Mass Storage driver... > [ 136.630764] scsi6 : usb-storage 2-1:1.0 > [ 136.631270] usbcore: registered new interface driver usb-storage > [ 136.631275] USB Mass Storage support registered. > [ 137.636863] scsi 6:0:0:0: Direct-Access Generic- Card Reader > 1.00 PQ: 0 ANSI: 0 CCS > [ 137.639519] sd 6:0:0:0: Attached scsi generic sg3 type 0 > [ 138.446467] sd 6:0:0:0: [sdc] 15661056 512-byte logical blocks: > (8.01 GB/7.46 GiB) > [ 138.447282] sd 6:0:0:0: [sdc] Write Protect is off > [ 138.447291] sd 6:0:0:0: [sdc] Mode Sense: 03 00 00 00 > [ 138.448138] sd 6:0:0:0: [sdc] No Caching mode page present > [ 138.448147] sd 6:0:0:0: [sdc] Assuming drive cache: write through > [ 138.451639] sd 6:0:0:0: [sdc] No Caching mode page present > [ 138.451647] sd 6:0:0:0: [sdc] Assuming drive cache: write through > [ 138.452729] sdc: sdc1 >> mount usb mem stick sdc1 > [ 168.838133] usb 2-1: reset high-speed USB device number 3 using ehci_hcd [... removed lot of similar USB errors ...] > driverbyte=DRIVER_SENSE > [ 478.342504] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] > [ 478.342510] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range > [ 478.342517] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 01 00 > [ 478.342528] end_request: I/O error, dev sdc, sector 8192 > [ 478.342545] FAT-fs (sdc1): unable to read boot sector > > > > On Thu, Jan 26, 2012 at 10:07 AM, Antti Palosaari<crope@iki.fi> wrote: >> On 01/26/2012 12:16 AM, Claus Olesen wrote: >>> >>> just got 3.2.1-3.fc16.i686.PAE >>> the issue that the driver had to be removed for the 290e to work after >>> a replug is gone. >>> the issue that a usb mem stick cannot be mounted while the 290e is >>> plugged in still lingers. >>> one workaround is to unplug the 290e and wait a little (no need to >>> also remove the driver). >> >> >> What it prints to the system log? Use tail -f /var/log/messages or dmesg. >> >> >> Antti >> -- >> http://palosaari.fi/ -- http://palosaari.fi/ ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: 290e locking issue 2012-01-26 11:58 ` Antti Palosaari @ 2012-01-26 15:18 ` Devin Heitmueller 2012-01-26 17:09 ` Claus Olesen 1 sibling, 0 replies; 9+ messages in thread From: Devin Heitmueller @ 2012-01-26 15:18 UTC (permalink / raw) To: Antti Palosaari; +Cc: Claus Olesen, linux-media On Thu, Jan 26, 2012 at 6:58 AM, Antti Palosaari <crope@iki.fi> wrote: > I think it is maybe some incapability of em28xx driver. Maybe it could be > something to do with USB HCI too... >From a USB standpoint there isn't a whole lot the em28xx driver could do wrong. It's an isoc device, and perhaps it's not clearing it's bandwidth reservation after streaming is done, but even in that case it shouldn't prevent a disk from working since those are typically bulk devices. Devin -- Devin J. Heitmueller - Kernel Labs http://www.kernellabs.com ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: 290e locking issue 2012-01-26 11:58 ` Antti Palosaari 2012-01-26 15:18 ` Devin Heitmueller @ 2012-01-26 17:09 ` Claus Olesen 2012-01-26 18:16 ` Antti Palosaari 1 sibling, 1 reply; 9+ messages in thread From: Claus Olesen @ 2012-01-26 17:09 UTC (permalink / raw) To: Antti Palosaari; +Cc: linux-media the behavior with the latest media_build.git is the same as that which was with fedora stock. the dmesg is >inplug 290e [ 112.284350] usb 2-3: new high-speed USB device number 2 using ehci_hcd [ 112.399774] usb 2-3: New USB device found, idVendor=2013, idProduct=024f [ 112.399783] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 112.399790] usb 2-3: Product: PCTV 290e [ 112.399796] usb 2-3: Manufacturer: PCTV Systems [ 112.399802] usb 2-3: SerialNumber: 00000006VEJQ [ 112.920507] em28xx: New device PCTV Systems PCTV 290e @ 480 Mbps (2013:024f, interface 0, class 0) [ 112.920515] em28xx: DVB interface 0 found [ 112.920647] em28xx #0: chip ID is em28174 [ 113.216668] em28xx #0: Identified as PCTV nanoStick T2 290e (card=78) [ 113.258309] Registered IR keymap rc-pinnacle-pctv-hd [ 113.258579] input: em28xx IR (em28xx #0) as /devices/pci0000:00/0000:00:1d.7/usb2/2-3/rc/rc1/input19 [ 113.259685] rc1: em28xx IR (em28xx #0) as /devices/pci0000:00/0000:00:1d.7/usb2/2-3/rc/rc1 [ 113.260303] em28xx #0: v4l2 driver version 0.1.3 [ 113.265485] em28xx #0: V4L2 video device registered as video1 [ 113.266619] usbcore: registered new interface driver em28xx [ 113.301706] WARNING: You are using an experimental version of the media stack. [ 113.301709] As the driver is backported to an older kernel, it doesn't offer [ 113.301710] enough quality for its usage in production. [ 113.301711] Use it with care. [ 113.301712] Latest git patches (needed if you report a bug to linux-media@vger.kernel.org): [ 113.301713] 59b30294e14fa6a370fdd2bc2921cca1f977ef16 Merge branch 'v4l_for_linus' into staging/for_v3.4 [ 113.301714] 72565224609a23a60d10fcdf42f87a2fa8f7b16d [media] cxd2820r: sleep on DVB-T/T2 delivery system switch [ 113.301715] 46de20a78ae4b122b79fc02633e9a6c3d539ecad [media] anysee: fix CI init [ 113.382193] tda18271 17-0060: creating new instance [ 113.386895] TDA18271HD/C2 detected @ 17-0060 [ 113.629529] DVB: registering new adapter (em28xx #0) [ 113.629541] DVB: registering adapter 0 frontend 0 (Sony CXD2820R)... [ 113.632902] em28xx #0: Successfully loaded em28xx-dvb [ 113.632910] Em28xx: Initialized (Em28xx dvb Extension) extension >inplug usb mem stick [ 152.204343] usb 2-1: new high-speed USB device number 3 using ehci_hcd [ 152.336629] usb 2-1: New USB device found, idVendor=0bda, idProduct=0120 [ 152.336639] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 152.336646] usb 2-1: Product: USB2.0-CRW [ 152.336652] usb 2-1: Manufacturer: Generic [ 152.336657] usb 2-1: SerialNumber: 20060413092100000 [ 152.655077] Initializing USB Mass Storage driver... [ 152.655230] scsi6 : usb-storage 2-1:1.0 [ 152.655334] usbcore: registered new interface driver usb-storage [ 152.655336] USB Mass Storage support registered. [ 153.659503] scsi 6:0:0:0: Direct-Access Generic- Card Reader 1.00 PQ: 0 ANSI: 0 CCS [ 153.661960] sd 6:0:0:0: Attached scsi generic sg3 type 0 [ 154.551529] sd 6:0:0:0: [sdc] 15661056 512-byte logical blocks: (8.01 GB/7.46 GiB) [ 154.552415] sd 6:0:0:0: [sdc] Write Protect is off [ 154.552424] sd 6:0:0:0: [sdc] Mode Sense: 03 00 00 00 [ 154.553309] sd 6:0:0:0: [sdc] No Caching mode page present [ 154.553318] sd 6:0:0:0: [sdc] Assuming drive cache: write through [ 154.556786] sd 6:0:0:0: [sdc] No Caching mode page present [ 154.556793] sd 6:0:0:0: [sdc] Assuming drive cache: write through [ 154.557864] sdc: sdc1 >mount usb mem stick sdc1 [ 184.838198] usb 2-1: reset high-speed USB device number 3 using ehci_hcd [ 184.959925] sd 6:0:0:0: [sdc] No Caching mode page present [ 184.959936] sd 6:0:0:0: [sdc] Assuming drive cache: write through [ 184.959944] sd 6:0:0:0: [sdc] Attached SCSI removable disk [ 215.878053] usb 2-1: reset high-speed USB device number 3 using ehci_hcd [ 215.998116] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 215.998123] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 215.998128] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 215.998135] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 80 00 00 08 00 [ 215.998147] end_request: I/O error, dev sdc, sector 15660928 [ 215.998152] Buffer I/O error on device sdc, logical block 1957616 [ 215.999614] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 215.999619] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 215.999623] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 215.999629] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 80 00 00 08 00 [ 215.999639] end_request: I/O error, dev sdc, sector 15660928 [ 215.999642] Buffer I/O error on device sdc, logical block 1957616 [ 216.000987] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 216.000992] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 216.000996] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 216.001045] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 f0 00 00 08 00 [ 216.001055] end_request: I/O error, dev sdc, sector 15661040 [ 216.001058] Buffer I/O error on device sdc, logical block 1957630 [ 216.002119] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 216.002124] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 216.002129] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 216.002135] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 80 00 00 08 00 [ 216.002145] end_request: I/O error, dev sdc, sector 15660928 [ 216.002149] Buffer I/O error on device sdc1, logical block 1956592 [ 216.003238] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 216.003243] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 216.003247] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 216.003253] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 f0 00 00 08 00 [ 216.003263] end_request: I/O error, dev sdc, sector 15661040 [ 216.003266] Buffer I/O error on device sdc, logical block 1957630 [ 216.004365] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 216.004370] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 216.004374] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 216.004380] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 80 00 00 08 00 [ 216.004390] end_request: I/O error, dev sdc, sector 15660928 [ 216.004394] Buffer I/O error on device sdc1, logical block 1956592 [ 216.005490] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 216.005495] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 216.005499] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 216.005505] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 216.005515] end_request: I/O error, dev sdc, sector 0 [ 216.005518] Buffer I/O error on device sdc, logical block 0 [ 219.880502] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 219.880507] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 219.880511] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 219.880516] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 f0 00 00 08 00 [ 219.880524] end_request: I/O error, dev sdc, sector 15661040 [ 219.880528] Buffer I/O error on device sdc1, logical block 1956606 [ 219.881999] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 219.882015] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 219.882020] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 219.882028] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 219.882047] end_request: I/O error, dev sdc, sector 0 [ 219.882052] Buffer I/O error on device sdc, logical block 0 [ 219.883480] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 219.883484] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 219.883487] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 219.883492] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 ee f7 f0 00 00 08 00 [ 219.883499] end_request: I/O error, dev sdc, sector 15661040 [ 219.884732] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 219.884736] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 219.884739] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 219.884743] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 08 00 [ 219.884750] end_request: I/O error, dev sdc, sector 8192 --- cut similar --- [ 219.932609] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 219.932614] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 219.932618] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 219.932624] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 08 00 [ 219.932633] end_request: I/O error, dev sdc, sector 8192 [ 222.265999] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 222.266017] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 222.266022] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 222.266030] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 08 00 [ 222.266049] end_request: I/O error, dev sdc, sector 8192 [ 222.266055] quiet_error: 31 callbacks suppressed [ 222.266059] Buffer I/O error on device sdc1, logical block 0 [ 222.267359] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 222.267365] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 222.267370] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 222.267375] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 08 00 00 08 00 [ 222.267385] end_request: I/O error, dev sdc, sector 8200 [ 222.267389] Buffer I/O error on device sdc1, logical block 1 [ 222.276618] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 222.276632] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 222.276642] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 222.276654] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 10 00 [ 222.276675] end_request: I/O error, dev sdc, sector 8192 [ 222.276686] Buffer I/O error on device sdc1, logical block 0 [ 222.276701] Buffer I/O error on device sdc1, logical block 1 [ 222.277987] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 222.277992] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 222.277997] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 222.278014] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 08 00 [ 222.278031] end_request: I/O error, dev sdc, sector 8192 [ 222.278036] Buffer I/O error on device sdc1, logical block 0 --- cut similar --- [ 314.433818] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 314.433829] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 314.433840] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 314.433853] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 02 00 00 02 00 [ 314.433874] end_request: I/O error, dev sdc, sector 8194 [ 314.433905] EXT4-fs (sdc1): unable to read superblock [ 314.438939] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 314.438950] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 314.438960] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 314.438972] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 40 00 00 02 00 [ 314.438994] end_request: I/O error, dev sdc, sector 8256 [ 314.439027] isofs_fill_super: bread failed, dev=sdc1, iso_blknum=16, block=32 [ 314.481436] sd 6:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 314.481443] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] [ 314.481449] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range [ 314.481456] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 01 00 [ 314.481467] end_request: I/O error, dev sdc, sector 8192 [ 314.481485] FAT-fs (sdc1): unable to read boot sector On Thu, Jan 26, 2012 at 12:58 PM, Antti Palosaari <crope@iki.fi> wrote: > On 01/26/2012 01:46 PM, Claus Olesen wrote: >> >> the dmesg output from inplug of 290e until usb mem stick mount timeout >> with a cut marked "--- cut similar ---" between mount and timeout for >> less output is > > > I think it is maybe some incapability of em28xx driver. Maybe it could be > something to do with USB HCI too... > > > Could you test latest drivers using media_build.git ? > > > >> >>> inplug 290e >> >> [ 112.367345] usb 2-3: new high-speed USB device number 2 using ehci_hcd >> [ 112.482773] usb 2-3: New USB device found, idVendor=2013, >> idProduct=024f >> [ 112.482783] usb 2-3: New USB device strings: Mfr=1, Product=2, >> SerialNumber=3 >> [ 112.482790] usb 2-3: Product: PCTV 290e >> [ 112.482796] usb 2-3: Manufacturer: PCTV Systems >> [ 112.482801] usb 2-3: SerialNumber: 00000006VEJQ >> [ 112.988850] em28xx: New device PCTV Systems PCTV 290e @ 480 Mbps >> (2013:024f, interface 0, class 0) >> [ 112.988929] em28xx #0: chip ID is em28174 >> [ 113.284694] em28xx #0: Identified as PCTV nanoStick T2 290e (card=78) >> [ 113.340323] Registered IR keymap rc-pinnacle-pctv-hd >> [ 113.340594] input: em28xx IR (em28xx #0) as >> /devices/pci0000:00/0000:00:1d.7/usb2/2-3/rc/rc1/input19 >> [ 113.341677] rc1: em28xx IR (em28xx #0) as >> /devices/pci0000:00/0000:00:1d.7/usb2/2-3/rc/rc1 >> [ 113.342411] em28xx #0: v4l2 driver version 0.1.3 >> [ 113.348855] em28xx #0: V4L2 video device registered as video1 >> [ 113.350562] usbcore: registered new interface driver em28xx >> [ 113.350568] em28xx driver loaded >> [ 113.480057] tda18271 17-0060: creating new instance >> [ 113.485221] TDA18271HD/C2 detected @ 17-0060 >> [ 113.724218] tda18271 17-0060: attaching existing instance >> [ 113.724227] DVB: registering new adapter (em28xx #0) >> [ 113.724235] DVB: registering adapter 0 frontend 0 (Sony CXD2820R >> (DVB-T/T2))... >> [ 113.724763] DVB: registering adapter 0 frontend 1 (Sony CXD2820R >> (DVB-C))... >> [ 113.728614] em28xx #0: Successfully loaded em28xx-dvb >> [ 113.728617] Em28xx: Initialized (Em28xx dvb Extension) extension >>> >>> inplug usb mem stick >> >> [ 136.177341] usb 2-1: new high-speed USB device number 3 using ehci_hcd >> [ 136.308531] usb 2-1: New USB device found, idVendor=0bda, >> idProduct=0120 >> [ 136.308541] usb 2-1: New USB device strings: Mfr=1, Product=2, >> SerialNumber=3 >> [ 136.308548] usb 2-1: Product: USB2.0-CRW >> [ 136.308554] usb 2-1: Manufacturer: Generic >> [ 136.308559] usb 2-1: SerialNumber: 20060413092100000 >> [ 136.630379] Initializing USB Mass Storage driver... >> [ 136.630764] scsi6 : usb-storage 2-1:1.0 >> [ 136.631270] usbcore: registered new interface driver usb-storage >> [ 136.631275] USB Mass Storage support registered. >> [ 137.636863] scsi 6:0:0:0: Direct-Access Generic- Card Reader >> 1.00 PQ: 0 ANSI: 0 CCS >> [ 137.639519] sd 6:0:0:0: Attached scsi generic sg3 type 0 >> [ 138.446467] sd 6:0:0:0: [sdc] 15661056 512-byte logical blocks: >> (8.01 GB/7.46 GiB) >> [ 138.447282] sd 6:0:0:0: [sdc] Write Protect is off >> [ 138.447291] sd 6:0:0:0: [sdc] Mode Sense: 03 00 00 00 >> [ 138.448138] sd 6:0:0:0: [sdc] No Caching mode page present >> [ 138.448147] sd 6:0:0:0: [sdc] Assuming drive cache: write through >> [ 138.451639] sd 6:0:0:0: [sdc] No Caching mode page present >> [ 138.451647] sd 6:0:0:0: [sdc] Assuming drive cache: write through >> [ 138.452729] sdc: sdc1 >>> >>> mount usb mem stick sdc1 >> >> [ 168.838133] usb 2-1: reset high-speed USB device number 3 using >> ehci_hcd > > > [... removed lot of similar USB errors ...] > > >> driverbyte=DRIVER_SENSE >> [ 478.342504] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current] >> [ 478.342510] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of >> range >> [ 478.342517] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 01 >> 00 >> [ 478.342528] end_request: I/O error, dev sdc, sector 8192 >> [ 478.342545] FAT-fs (sdc1): unable to read boot sector >> >> >> >> On Thu, Jan 26, 2012 at 10:07 AM, Antti Palosaari<crope@iki.fi> wrote: >>> >>> On 01/26/2012 12:16 AM, Claus Olesen wrote: >>>> >>>> >>>> just got 3.2.1-3.fc16.i686.PAE >>>> the issue that the driver had to be removed for the 290e to work after >>>> a replug is gone. >>>> the issue that a usb mem stick cannot be mounted while the 290e is >>>> plugged in still lingers. >>>> one workaround is to unplug the 290e and wait a little (no need to >>>> also remove the driver). >>> >>> >>> >>> What it prints to the system log? Use tail -f /var/log/messages or dmesg. >>> >>> >>> Antti >>> -- >>> http://palosaari.fi/ > > > > -- > http://palosaari.fi/ ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: 290e locking issue 2012-01-26 17:09 ` Claus Olesen @ 2012-01-26 18:16 ` Antti Palosaari 2012-01-26 19:25 ` Claus Olesen 0 siblings, 1 reply; 9+ messages in thread From: Antti Palosaari @ 2012-01-26 18:16 UTC (permalink / raw) To: Claus Olesen; +Cc: linux-media On 01/26/2012 07:09 PM, Claus Olesen wrote: > the behavior with the latest media_build.git is the same as that which > was with fedora stock. After all I am almost 100% sure it is em28xx (USB-interface driver used) or/and USB-bus related issue. Likely it will happen for other em28xx devices too. But as I do not have enough knowledge about that area I cannot do much for fixing it. Maybe it is better try to avoid using those devices same time and try use USB-hub, other USB-port, add new USB-controller, etc... regards Antti -- http://palosaari.fi/ ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: 290e locking issue 2012-01-26 18:16 ` Antti Palosaari @ 2012-01-26 19:25 ` Claus Olesen 2012-01-26 19:41 ` Devin Heitmueller 0 siblings, 1 reply; 9+ messages in thread From: Claus Olesen @ 2012-01-26 19:25 UTC (permalink / raw) To: Antti Palosaari; +Cc: linux-media I just came to think of my old 800e because also it is a em28xx device and for what it is worth I just tried it and it does not exhibit the issue. it's dmesg is >inplug 800e [ 179.499370] usb 2-4: new high-speed USB device number 2 using ehci_hcd [ 179.622477] usb 2-4: New USB device found, idVendor=2304, idProduct=0227 [ 179.622486] usb 2-4: New USB device strings: Mfr=3, Product=1, SerialNumber=2 [ 179.622494] usb 2-4: Product: PCTV 800e [ 179.622500] usb 2-4: Manufacturer: Pinnacle Systems [ 179.622505] usb 2-4: SerialNumber: 061101051592 [ 179.915633] em28xx: New device Pinnacle Systems PCTV 800e @ 480 Mbps (2304:0227, interface 0, class 0) [ 179.915636] em28xx: Audio Vendor Class interface 0 found [ 179.915638] em28xx: Video interface 0 found [ 179.915639] em28xx: DVB interface 0 found [ 179.915749] em28xx #0: chip ID is em2882/em2883 [ 180.058726] em28xx #0: i2c eeprom 00: 1a eb 67 95 04 23 27 02 d0 12 5c 03 8e 16 a4 1c [ 180.058753] em28xx #0: i2c eeprom 10: 6a 24 27 57 46 07 01 00 00 00 00 00 00 00 00 00 [ 180.058775] em28xx #0: i2c eeprom 20: 46 00 01 00 f0 10 02 00 b8 00 00 00 5b 1c 00 00 [ 180.058798] em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 01 01 00 00 00 00 00 00 [ 180.058820] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 180.058841] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 180.058862] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 24 03 50 00 69 00 [ 180.058884] em28xx #0: i2c eeprom 70: 6e 00 6e 00 61 00 63 00 6c 00 65 00 20 00 53 00 [ 180.058906] em28xx #0: i2c eeprom 80: 79 00 73 00 74 00 65 00 6d 00 73 00 00 00 16 03 [ 180.058928] em28xx #0: i2c eeprom 90: 50 00 43 00 54 00 56 00 20 00 38 00 30 00 30 00 [ 180.058950] em28xx #0: i2c eeprom a0: 65 00 00 00 1c 03 30 00 36 00 31 00 31 00 30 00 [ 180.058972] em28xx #0: i2c eeprom b0: 31 00 30 00 35 00 31 00 35 00 39 00 32 00 00 00 [ 180.058994] em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 180.059079] em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 180.059125] em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 180.059170] em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 180.059219] em28xx #0: EEPROM ID= 0x9567eb1a, EEPROM hash = 0xd2e5aebf [ 180.059226] em28xx #0: EEPROM info: [ 180.059232] em28xx #0: AC97 audio (5 sample rates) [ 180.059239] em28xx #0: 500mA max power [ 180.059247] em28xx #0: Table at 0x27, strings=0x168e, 0x1ca4, 0x246a [ 180.060458] em28xx #0: Identified as Pinnacle PCTV HD Pro Stick (card=17) [ 180.091733] tvp5150 17-005c: chip found @ 0xb8 (em28xx #0) [ 180.140502] tvp5150 17-005c: tvp5150am1 detected. [ 180.147912] i2c-core: driver [tuner] using legacy suspend method [ 180.147919] i2c-core: driver [tuner] using legacy resume method [ 180.151227] tuner 17-0061: Tuner -1 found with type(s) Radio TV. [ 180.169032] xc2028 17-0061: creating new instance [ 180.169041] xc2028 17-0061: type set to XCeive xc2028/xc3028 tuner [ 180.174254] xc2028 17-0061: Error: firmware xc3028-v27.fw not found. [ 180.199094] Registered IR keymap rc-pinnacle-pctv-hd [ 180.199334] input: em28xx IR (em28xx #0) as /devices/pci0000:00/0000:00:1d.7/usb2/2-4/rc/rc1/input19 [ 180.200463] rc1: em28xx IR (em28xx #0) as /devices/pci0000:00/0000:00:1d.7/usb2/2-4/rc/rc1 [ 180.200895] em28xx #0: Config register raw data: 0xd0 [ 180.202271] em28xx #0: AC97 vendor ID = 0xffffffff [ 180.202640] em28xx #0: AC97 features = 0x6a90 [ 180.202644] em28xx #0: Empia 202 AC97 audio processor detected [ 180.366381] em28xx #0: v4l2 driver version 0.1.3 [ 180.371937] xc2028 17-0061: Error: firmware xc3028-v27.fw not found. [ 180.441716] em28xx #0: V4L2 video device registered as video1 [ 180.441723] em28xx #0: V4L2 VBI device registered as vbi0 [ 180.444325] usbcore: registered new interface driver em28xx [ 180.469757] em28xx-audio.c: probing for em28xx Audio Vendor Class [ 180.469760] em28xx-audio.c: Copyright (C) 2006 Markus Rechberger [ 180.469761] em28xx-audio.c: Copyright (C) 2007-2011 Mauro Carvalho Chehab [ 180.470139] Em28xx: Initialized (Em28xx Audio Extension) extension [ 180.473969] WARNING: You are using an experimental version of the media stack. [ 180.473971] As the driver is backported to an older kernel, it doesn't offer [ 180.473972] enough quality for its usage in production. [ 180.473973] Use it with care. [ 180.473973] Latest git patches (needed if you report a bug to linux-media@vger.kernel.org): [ 180.473975] 59b30294e14fa6a370fdd2bc2921cca1f977ef16 Merge branch 'v4l_for_linus' into staging/for_v3.4 [ 180.473976] 72565224609a23a60d10fcdf42f87a2fa8f7b16d [media] cxd2820r: sleep on DVB-T/T2 delivery system switch [ 180.473977] 46de20a78ae4b122b79fc02633e9a6c3d539ecad [media] anysee: fix CI init [ 180.669893] xc2028 17-0061: attaching existing instance [ 180.669901] xc2028 17-0061: type set to XCeive xc2028/xc3028 tuner [ 180.669906] em28xx #0: em28xx #0/2: xc3028 attached [ 180.669912] DVB: registering new adapter (em28xx #0) [ 180.669919] DVB: registering adapter 0 frontend 0 (LG Electronics LGDT3303 VSB/QAM Frontend)... [ 180.672073] em28xx #0: Successfully loaded em28xx-dvb [ 180.672085] Em28xx: Initialized (Em28xx dvb Extension) extension >inplug usb mem stick [ 208.445353] usb 2-1: new high-speed USB device number 3 using ehci_hcd [ 208.576550] usb 2-1: New USB device found, idVendor=0bda, idProduct=0120 [ 208.576560] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 208.576568] usb 2-1: Product: USB2.0-CRW [ 208.576573] usb 2-1: Manufacturer: Generic [ 208.576578] usb 2-1: SerialNumber: 20060413092100000 [ 208.876874] Initializing USB Mass Storage driver... [ 208.877477] scsi6 : usb-storage 2-1:1.0 [ 208.877749] usbcore: registered new interface driver usb-storage [ 208.877754] USB Mass Storage support registered. [ 209.881690] scsi 6:0:0:0: Direct-Access Generic- Card Reader 1.00 PQ: 0 ANSI: 0 CCS [ 209.884211] sd 6:0:0:0: Attached scsi generic sg3 type 0 [ 210.685592] sd 6:0:0:0: [sdc] 15661056 512-byte logical blocks: (8.01 GB/7.46 GiB) [ 210.686415] sd 6:0:0:0: [sdc] Write Protect is off [ 210.686425] sd 6:0:0:0: [sdc] Mode Sense: 03 00 00 00 [ 210.687304] sd 6:0:0:0: [sdc] No Caching mode page present [ 210.687313] sd 6:0:0:0: [sdc] Assuming drive cache: write through [ 210.690785] sd 6:0:0:0: [sdc] No Caching mode page present [ 210.690793] sd 6:0:0:0: [sdc] Assuming drive cache: write through [ 210.691861] sdc: sdc1 [ 210.694644] sd 6:0:0:0: [sdc] No Caching mode page present [ 210.694652] sd 6:0:0:0: [sdc] Assuming drive cache: write through [ 210.694659] sd 6:0:0:0: [sdc] Attached SCSI removable disk >mount usb memstick sdc1 [ 247.064778] SELinux: initialized (dev sdc1, type vfat), uses genfs_contexts On Thu, Jan 26, 2012 at 7:16 PM, Antti Palosaari <crope@iki.fi> wrote: > On 01/26/2012 07:09 PM, Claus Olesen wrote: >> >> the behavior with the latest media_build.git is the same as that which >> was with fedora stock. > > > After all I am almost 100% sure it is em28xx (USB-interface driver used) > or/and USB-bus related issue. Likely it will happen for other em28xx devices > too. But as I do not have enough knowledge about that area I cannot do much > for fixing it. Maybe it is better try to avoid using those devices same time > and try use USB-hub, other USB-port, add new USB-controller, etc... > > > regards > Antti > -- > http://palosaari.fi/ ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: 290e locking issue 2012-01-26 19:25 ` Claus Olesen @ 2012-01-26 19:41 ` Devin Heitmueller 0 siblings, 0 replies; 9+ messages in thread From: Devin Heitmueller @ 2012-01-26 19:41 UTC (permalink / raw) To: Claus Olesen; +Cc: Antti Palosaari, linux-media On Thu, Jan 26, 2012 at 2:25 PM, Claus Olesen <ceolesen@gmail.com> wrote: > I just came to think of my old 800e because also it is a em28xx device > and for what it is worth I just tried it and it does not exhibit the > issue. it's dmesg is Wow, that's *really* surprising (I did both the original em2874 driver support as well as the 800e driver, and as a result am intimately familiar with the differences). I'm not sure what is going on there. Devin -- Devin J. Heitmueller - Kernel Labs http://www.kernellabs.com ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2012-01-26 19:41 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2012-01-25 22:16 290e locking issue Claus Olesen 2012-01-26 9:07 ` Antti Palosaari 2012-01-26 11:46 ` Claus Olesen 2012-01-26 11:58 ` Antti Palosaari 2012-01-26 15:18 ` Devin Heitmueller 2012-01-26 17:09 ` Claus Olesen 2012-01-26 18:16 ` Antti Palosaari 2012-01-26 19:25 ` Claus Olesen 2012-01-26 19:41 ` Devin Heitmueller
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).