* EM28xx - MSI Digivox Trio - almost working. @ 2013-06-20 5:14 P. van Gaans 2013-06-20 7:40 ` Antti Palosaari 2013-08-08 0:37 ` P. van Gaans 0 siblings, 2 replies; 6+ messages in thread From: P. van Gaans @ 2013-06-20 5:14 UTC (permalink / raw) To: linux-media Hi all, (device: http://linuxtv.org/wiki/index.php/MSI_DigiVox_Trio) Thanks to the message from Philip Pemberton I was able to try loading the em28xx driver myself using: sudo modprobe em28xx card=NUMBER echo eb1a 2885 | sudo tee /sys/bus/usb/drivers/em28xx/new_id Here are the results for NUMBER: Card=79 (Terratec Cinergy H5): works, less corruption than card=87, just some blocks every few seconds. Attenuators didn't help. Card=81 (Hauppauge WinTV HVR 930C): doesn't work, no /dev/dvb adapter Card=82 (Terratec Cinergy HTC Stick): similar to card=87 Card=85 (PCTV QuatroStick (510e)): constantly producing i2c read errors, doesn't work Card=86 (PCTV QuatroStick nano (520e): same Card=87 (Terratec Cinergy HTC USB XS): stick works and scans channels, but reception is bugged with corruption. It's like having a DVB-T antenna that's just not good enough, except this is DVB-C and my signal is excellent. Attenuators didn't help. Card=88 (C3 Tech Digital Duo HDTV/SDTV USB): doesn't work, no /dev/dvb adapter So with card=79 it's really close to working. What else can I do? Best regareds, P. van Gaans ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: EM28xx - MSI Digivox Trio - almost working. 2013-06-20 5:14 EM28xx - MSI Digivox Trio - almost working P. van Gaans @ 2013-06-20 7:40 ` Antti Palosaari 2013-06-20 8:11 ` P. van Gaans 2013-08-08 0:37 ` P. van Gaans 1 sibling, 1 reply; 6+ messages in thread From: Antti Palosaari @ 2013-06-20 7:40 UTC (permalink / raw) To: P. van Gaans; +Cc: linux-media On 06/20/2013 08:14 AM, P. van Gaans wrote: > Hi all, > > (device: http://linuxtv.org/wiki/index.php/MSI_DigiVox_Trio) > > Thanks to the message from Philip Pemberton I was able to try loading > the em28xx driver myself using: > > sudo modprobe em28xx card=NUMBER > echo eb1a 2885 | sudo tee /sys/bus/usb/drivers/em28xx/new_id > > Here are the results for NUMBER: > > Card=79 (Terratec Cinergy H5): works, less corruption than card=87, just > some blocks every few seconds. Attenuators didn't help. > Card=81 (Hauppauge WinTV HVR 930C): doesn't work, no /dev/dvb adapter > Card=82 (Terratec Cinergy HTC Stick): similar to card=87 > Card=85 (PCTV QuatroStick (510e)): constantly producing i2c read errors, > doesn't work > Card=86 (PCTV QuatroStick nano (520e): same > Card=87 (Terratec Cinergy HTC USB XS): stick works and scans channels, > but reception is bugged with corruption. It's like having a DVB-T > antenna that's just not good enough, except this is DVB-C and my signal > is excellent. Attenuators didn't help. > Card=88 (C3 Tech Digital Duo HDTV/SDTV USB): doesn't work, no /dev/dvb > adapter > > So with card=79 it's really close to working. What else can I do? Take USB sniffs, generate code, copy & paste that to the driver until it starts working. After it start working start reducing generated code. That way with trial and error you will find out problematic register(s) very quickly. There is suitable scripts to generate em28xx drx-k code from the sniffs, maybe in dvb-utils package. Mauro has done that script. I used it when I added PCTV 520e support (problem was bug in DRX-K GPIO code). regards Antti -- http://palosaari.fi/ ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: EM28xx - MSI Digivox Trio - almost working. 2013-06-20 7:40 ` Antti Palosaari @ 2013-06-20 8:11 ` P. van Gaans 2013-06-20 8:20 ` Antti Palosaari 0 siblings, 1 reply; 6+ messages in thread From: P. van Gaans @ 2013-06-20 8:11 UTC (permalink / raw) To: linux-media On 20-06-13 09:40, Antti Palosaari wrote: > On 06/20/2013 08:14 AM, P. van Gaans wrote: >> Hi all, >> >> (device: http://linuxtv.org/wiki/index.php/MSI_DigiVox_Trio) >> >> Thanks to the message from Philip Pemberton I was able to try loading >> the em28xx driver myself using: >> >> sudo modprobe em28xx card=NUMBER >> echo eb1a 2885 | sudo tee /sys/bus/usb/drivers/em28xx/new_id >> >> Here are the results for NUMBER: >> >> Card=79 (Terratec Cinergy H5): works, less corruption than card=87, just >> some blocks every few seconds. Attenuators didn't help. >> Card=81 (Hauppauge WinTV HVR 930C): doesn't work, no /dev/dvb adapter >> Card=82 (Terratec Cinergy HTC Stick): similar to card=87 >> Card=85 (PCTV QuatroStick (510e)): constantly producing i2c read errors, >> doesn't work >> Card=86 (PCTV QuatroStick nano (520e): same >> Card=87 (Terratec Cinergy HTC USB XS): stick works and scans channels, >> but reception is bugged with corruption. It's like having a DVB-T >> antenna that's just not good enough, except this is DVB-C and my signal >> is excellent. Attenuators didn't help. >> Card=88 (C3 Tech Digital Duo HDTV/SDTV USB): doesn't work, no /dev/dvb >> adapter >> >> So with card=79 it's really close to working. What else can I do? > > Take USB sniffs, generate code, copy & paste that to the driver until it > starts working. After it start working start reducing generated code. > That way with trial and error you will find out problematic register(s) > very quickly. > > There is suitable scripts to generate em28xx drx-k code from the sniffs, > maybe in dvb-utils package. Mauro has done that script. I used it when I > added PCTV 520e support (problem was bug in DRX-K GPIO code). > > regards > Antti > Hi Antti, Thanks for your answer. Do you mean I sniff on Windows or Linux? Would you happen to remember the name of the script you are referring to? Also in em28xx-new (https://bitbucket.org/mdonoughe/em28xx-new/overview) the device was supported. Wouldn't it be easier to try and find the differences between the Cinergy H5 and the Digivox in that code, or should I not even think of going there? Best regards, P. van Gaans ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: EM28xx - MSI Digivox Trio - almost working. 2013-06-20 8:11 ` P. van Gaans @ 2013-06-20 8:20 ` Antti Palosaari 0 siblings, 0 replies; 6+ messages in thread From: Antti Palosaari @ 2013-06-20 8:20 UTC (permalink / raw) To: P. van Gaans; +Cc: linux-media On 06/20/2013 11:11 AM, P. van Gaans wrote: > On 20-06-13 09:40, Antti Palosaari wrote: >> On 06/20/2013 08:14 AM, P. van Gaans wrote: >>> Hi all, >>> >>> (device: http://linuxtv.org/wiki/index.php/MSI_DigiVox_Trio) >>> >>> Thanks to the message from Philip Pemberton I was able to try loading >>> the em28xx driver myself using: >>> >>> sudo modprobe em28xx card=NUMBER >>> echo eb1a 2885 | sudo tee /sys/bus/usb/drivers/em28xx/new_id >>> >>> Here are the results for NUMBER: >>> >>> Card=79 (Terratec Cinergy H5): works, less corruption than card=87, just >>> some blocks every few seconds. Attenuators didn't help. >>> Card=81 (Hauppauge WinTV HVR 930C): doesn't work, no /dev/dvb adapter >>> Card=82 (Terratec Cinergy HTC Stick): similar to card=87 >>> Card=85 (PCTV QuatroStick (510e)): constantly producing i2c read errors, >>> doesn't work >>> Card=86 (PCTV QuatroStick nano (520e): same >>> Card=87 (Terratec Cinergy HTC USB XS): stick works and scans channels, >>> but reception is bugged with corruption. It's like having a DVB-T >>> antenna that's just not good enough, except this is DVB-C and my signal >>> is excellent. Attenuators didn't help. >>> Card=88 (C3 Tech Digital Duo HDTV/SDTV USB): doesn't work, no /dev/dvb >>> adapter >>> >>> So with card=79 it's really close to working. What else can I do? >> >> Take USB sniffs, generate code, copy & paste that to the driver until it >> starts working. After it start working start reducing generated code. >> That way with trial and error you will find out problematic register(s) >> very quickly. >> >> There is suitable scripts to generate em28xx drx-k code from the sniffs, >> maybe in dvb-utils package. Mauro has done that script. I used it when I >> added PCTV 520e support (problem was bug in DRX-K GPIO code). >> >> regards >> Antti >> > > Hi Antti, > > Thanks for your answer. Do you mean I sniff on Windows or Linux? Would > you happen to remember the name of the script you are referring to? > > Also in em28xx-new (https://bitbucket.org/mdonoughe/em28xx-new/overview) > the device was supported. Wouldn't it be easier to try and find the > differences between the Cinergy H5 and the Digivox in that code, or > should I not even think of going there? > > Best regards, > > P. van Gaans Download codes and look yourself. Also, I have added MaxMedia UB425-TC to that driver. You should test it too. Basically there is not much critical that differs between those devices. GPIO is the most important. Also some dummy analog decoder init could be needed. You have to take sniffs and compare those against drivers. There is not much I could do for you. regards Antti -- http://palosaari.fi/ ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: EM28xx - MSI Digivox Trio - almost working. 2013-06-20 5:14 EM28xx - MSI Digivox Trio - almost working P. van Gaans 2013-06-20 7:40 ` Antti Palosaari @ 2013-08-08 0:37 ` P. van Gaans 2013-10-23 23:03 ` P. van Gaans 1 sibling, 1 reply; 6+ messages in thread From: P. van Gaans @ 2013-08-08 0:37 UTC (permalink / raw) To: linux-media On 20-06-13 07:14, P. van Gaans wrote: > Hi all, > > (device: http://linuxtv.org/wiki/index.php/MSI_DigiVox_Trio) > > Thanks to the message from Philip Pemberton I was able to try loading > the em28xx driver myself using: > > sudo modprobe em28xx card=NUMBER > echo eb1a 2885 | sudo tee /sys/bus/usb/drivers/em28xx/new_id > > Here are the results for NUMBER: > > Card=79 (Terratec Cinergy H5): works, less corruption than card=87, just > some blocks every few seconds. Attenuators didn't help. > Card=81 (Hauppauge WinTV HVR 930C): doesn't work, no /dev/dvb adapter > Card=82 (Terratec Cinergy HTC Stick): similar to card=87 > Card=85 (PCTV QuatroStick (510e)): constantly producing i2c read errors, > doesn't work > Card=86 (PCTV QuatroStick nano (520e): same > Card=87 (Terratec Cinergy HTC USB XS): stick works and scans channels, > but reception is bugged with corruption. It's like having a DVB-T > antenna that's just not good enough, except this is DVB-C and my signal > is excellent. Attenuators didn't help. > Card=88 (C3 Tech Digital Duo HDTV/SDTV USB): doesn't work, no /dev/dvb > adapter > > So with card=79 it's really close to working. What else can I do? > > Best regareds, > > P. van Gaans > -- > To unsubscribe from this list: send the line "unsubscribe linux-media" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Hi all, Success! While I never succeeded in figuring out how the sniffing is supposed to be done (how to get any output from those scripts anyway? how to load the debug module in such away it actually works? run on native linux, or a windows VM on linux, or snoop in windows en run the script on linux? you get the picture) I just noticed a little notice on the DVB-C USB wiki page: "If you are experiencing problems with USB devices, it may not be the fault of the tuner. For example AMD 700 series chipsets (e.g. 780G) have a problem with USB ports which results in tuners working or partially working or not working at all." I was actually not even testing on an AMD 700 series but on an AMD 600 series. And a somewhat older kernel, with latest v4l-dvb compiled. So here's what I did: I took the Digivox Trio, plugged it in an Ivy Bridgy computer with Lubuntu 13.04 (stock kernel, stock v4l-dvb, Lubuntu appears to come with the firmware preloaded), load the em28xx driver as if the Digivox were a Terratec H5 and watched 5 minutes or so, flawless. I will continue to test and watch some longer programs, but right now it appears it is safe to say the Digivox Trio can be supported by simply treating as an H5. Best regards, P. van Gaans ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: EM28xx - MSI Digivox Trio - almost working. 2013-08-08 0:37 ` P. van Gaans @ 2013-10-23 23:03 ` P. van Gaans 0 siblings, 0 replies; 6+ messages in thread From: P. van Gaans @ 2013-10-23 23:03 UTC (permalink / raw) To: linux-media On 08/08/2013 02:37 AM, P. van Gaans wrote: > On 20-06-13 07:14, P. van Gaans wrote: >> Hi all, >> >> (device: http://linuxtv.org/wiki/index.php/MSI_DigiVox_Trio) >> >> Thanks to the message from Philip Pemberton I was able to try loading >> the em28xx driver myself using: >> >> sudo modprobe em28xx card=NUMBER >> echo eb1a 2885 | sudo tee /sys/bus/usb/drivers/em28xx/new_id >> >> Here are the results for NUMBER: >> >> Card=79 (Terratec Cinergy H5): works, less corruption than card=87, just >> some blocks every few seconds. Attenuators didn't help. >> Card=81 (Hauppauge WinTV HVR 930C): doesn't work, no /dev/dvb adapter >> Card=82 (Terratec Cinergy HTC Stick): similar to card=87 >> Card=85 (PCTV QuatroStick (510e)): constantly producing i2c read errors, >> doesn't work >> Card=86 (PCTV QuatroStick nano (520e): same >> Card=87 (Terratec Cinergy HTC USB XS): stick works and scans channels, >> but reception is bugged with corruption. It's like having a DVB-T >> antenna that's just not good enough, except this is DVB-C and my signal >> is excellent. Attenuators didn't help. >> Card=88 (C3 Tech Digital Duo HDTV/SDTV USB): doesn't work, no /dev/dvb >> adapter >> >> So with card=79 it's really close to working. What else can I do? >> >> Best regareds, >> >> P. van Gaans >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-media" in >> the body of a message to majordomo@vger.kernel.org >> More majordomo info at http://vger.kernel.org/majordomo-info.html >> > > Hi all, > > Success! > > While I never succeeded in figuring out how the sniffing is supposed to > be done (how to get any output from those scripts anyway? how to load > the debug module in such away it actually works? run on native linux, or > a windows VM on linux, or snoop in windows en run the script on linux? > you get the picture) I just noticed a little notice on the DVB-C USB > wiki page: > > "If you are experiencing problems with USB devices, it may not be the > fault of the tuner. For example AMD 700 series chipsets (e.g. 780G) have > a problem with USB ports which results in tuners working or partially > working or not working at all." > > I was actually not even testing on an AMD 700 series but on an AMD 600 > series. And a somewhat older kernel, with latest v4l-dvb compiled. > > So here's what I did: I took the Digivox Trio, plugged it in an Ivy > Bridgy computer with Lubuntu 13.04 (stock kernel, stock v4l-dvb, Lubuntu > appears to come with the firmware preloaded), load the em28xx driver as > if the Digivox were a Terratec H5 and watched 5 minutes or so, flawless. > > I will continue to test and watch some longer programs, but right now it > appears it is safe to say the Digivox Trio can be supported by simply > treating as an H5. > > Best regards, > > P. van Gaans > -- > To unsubscribe from this list: send the line "unsubscribe linux-media" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > It's been a while I've been using this setup and I haven't found any obvious flaws. I've added this to my own linux/drivers/media/usb/em28xx/em28xx-cards.c: { USB_DEVICE(0xeb1a, 0x2885), /* MSI Digivox Trio */ .driver_info = EM2884_BOARD_TERRATEC_H5 }, So it would load automatically. I've been using two of these with tvheadend. So can this device be added? Any more info needed? Best regards, P. van Gaans ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2013-10-23 23:02 UTC | newest] Thread overview: 6+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2013-06-20 5:14 EM28xx - MSI Digivox Trio - almost working P. van Gaans 2013-06-20 7:40 ` Antti Palosaari 2013-06-20 8:11 ` P. van Gaans 2013-06-20 8:20 ` Antti Palosaari 2013-08-08 0:37 ` P. van Gaans 2013-10-23 23:03 ` P. van Gaans
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).