* Bugs reporting
@ 2015-08-21 14:32 Anton Tinchev
2015-08-24 12:26 ` AW: " Norbert Auge
0 siblings, 1 reply; 4+ messages in thread
From: Anton Tinchev @ 2015-08-21 14:32 UTC (permalink / raw)
To: Norbert Auge, linux-media; +Cc: Georgi Chorbadzhiyski, Marian Zahariev
Hi,
can you point me where is usually reported the bugs with the cards firmware and/or drivers.
The combination is Cine S2 v6.5 with Duoflex S2 V4.
The miniDiSEqC (AB) is not working on the Duoflex S2 V4. Is not board fault, same behavior have
all cards i tested - about 20 Duoflex and 8 Cine modules.
For the protocol i tested:
Cine S2 v6.5 + Duoflex S2 V4:
- ports 0 and 1 (Ports on Cine card) - miniDiSEqC is working
- ports 0 and 1 (Ports on Cine card) - DiSEqC is working
- ports 2 and up (Ports on Duflex cards) - DiSEqC is working
- ports 2 and up (Ports on Duflex cards) - miniDiSEqC is NOT WORKING
Cine S2 v6.2 + Duoflex S2 older versions:
- all ports - both Cine and Duoflex - miniDiSEqC is working
- all ports - both Cine and Duoflex - DiSEqC is working
Cine S2 v6.5 + Duoflex S2 older version:
- Not tested, will test soon
Cine S2 v6.2 + Duoflex S2 V4:
- Not tested, will test when purchase next batch.
Also there is tons of errors on i2c bus to Duoflex S2 V4 tabs.
This was tested with latest drivers, also was tested with stock drivers with several
kernel versions from 3.18.11 to 4.2 rc2 - same behavior
^ permalink raw reply [flat|nested] 4+ messages in thread
* AW: Bugs reporting
2015-08-21 14:32 Bugs reporting Anton Tinchev
@ 2015-08-24 12:26 ` Norbert Auge
2015-08-24 16:39 ` Anton Tinchev
0 siblings, 1 reply; 4+ messages in thread
From: Norbert Auge @ 2015-08-24 12:26 UTC (permalink / raw)
To: 'Anton Tinchev', linux-media
Cc: 'Georgi Chorbadzhiyski', 'Marian Zahariev'
Hello Anton,
the driver for STV0910 does not support ToneBurst (=minidiseqc).
If it is essential for you we can address this in our driver development
best regards
Dieter
-----Ursprüngliche Nachricht-----
Von: Anton Tinchev [mailto:atl@unixsol.org]
Gesendet: Freitag, 21. August 2015 16:33
An: Norbert Auge; linux-media@vger.kernel.org
Cc: Georgi Chorbadzhiyski; Marian Zahariev
Betreff: Bugs reporting
Hi,
can you point me where is usually reported the bugs with the cards firmware and/or drivers.
The combination is Cine S2 v6.5 with Duoflex S2 V4.
The miniDiSEqC (AB) is not working on the Duoflex S2 V4. Is not board fault, same behavior have all cards i tested - about 20 Duoflex and 8 Cine modules.
For the protocol i tested:
Cine S2 v6.5 + Duoflex S2 V4:
- ports 0 and 1 (Ports on Cine card) - miniDiSEqC is working
- ports 0 and 1 (Ports on Cine card) - DiSEqC is working
- ports 2 and up (Ports on Duflex cards) - DiSEqC is working
- ports 2 and up (Ports on Duflex cards) - miniDiSEqC is NOT WORKING
Cine S2 v6.2 + Duoflex S2 older versions:
- all ports - both Cine and Duoflex - miniDiSEqC is working
- all ports - both Cine and Duoflex - DiSEqC is working
Cine S2 v6.5 + Duoflex S2 older version:
- Not tested, will test soon
Cine S2 v6.2 + Duoflex S2 V4:
- Not tested, will test when purchase next batch.
Also there is tons of errors on i2c bus to Duoflex S2 V4 tabs.
This was tested with latest drivers, also was tested with stock drivers with several kernel versions from 3.18.11 to 4.2 rc2 - same behavior
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: AW: Bugs reporting
2015-08-24 12:26 ` AW: " Norbert Auge
@ 2015-08-24 16:39 ` Anton Tinchev
[not found] ` <00cd01d0df1f$d4da9760$7e8fc620$@digitaldevices.de>
0 siblings, 1 reply; 4+ messages in thread
From: Anton Tinchev @ 2015-08-24 16:39 UTC (permalink / raw)
To: Norbert Auge, linux-media
Cc: 'Georgi Chorbadzhiyski', 'Marian Zahariev'
Hello.
It is not critical (our multiswitches works with normal disqc too), but should be reported and taken care.
Most important are the i2c errors i'm getting:
This during module load
------------
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.518270] Attaching STV0900 demodulator(2) Cut=0x30
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.518597] LNBx2x attached on addr=8
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.519359] stv6110x_attach: Attaching STV6110x
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.519740] attach tuner input 1 adr 63
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.520160] ddbridge 0000:02:00.0: DVB: registering adapter 1 frontend 0 (STV090x Multistandard)...
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.523102] Found STV0910 id=0x51
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.524056] hub 2-1:1.0: USB hub found
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.524540] hub 2-1:1.0: 6 ports detected
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.529937] ndiv = 18, MasterClock = 135000000
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.540615] lnbh25: i2c_write error
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.541479] LNB25 on 0c
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.544768] attach_init OK
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.546639] stv6111_regs = 08 41 8f 12 ce 54 55 45 47 b5 11
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.547047] reg[] = 08 41 8f 02 ce 54 55 45 46 bd 11
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.548011] ddbridge 0000:02:00.0: DVB: registering adapter 2 frontend 0 (STV0910)...
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.549037] lnbh25: i2c_write error
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.549897] LNB25 on 0d
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.552078] attach_init OK
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.553953] stv6111_regs = 08 41 8f 12 ce 54 55 45 47 b5 11
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.554400] reg[] = 08 41 8f 02 ce 54 55 45 46 bd 11
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.555401] ddbridge 0000:02:00.0: DVB: registering adapter 3 frontend 0 (STV0910)...
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.557056] Found STV0910 id=0x51
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.563966] ndiv = 18, MasterClock = 135000000
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.573658] lnbh25: i2c_write error
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.574560] LNB25 on 0c
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.576780] attach_init OK
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.578680] stv6111_regs = 08 41 8f 12 ce 54 55 45 47 b5 11
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.579121] reg[] = 08 41 8f 02 ce 54 55 45 46 bd 11
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.580113] ddbridge 0000:02:00.0: DVB: registering adapter 4 frontend 0 (STV0910)...
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.581138] lnbh25: i2c_write error
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.582043] LNB25 on 0d
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.584268] attach_init OK
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.586166] stv6111_regs = 08 41 8f 12 ce 54 55 45 47 b5 11
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.586611] reg[] = 08 41 8f 02 ce 54 55 45 46 bd 11
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.587615] ddbridge 0000:02:00.0: DVB: registering adapter 5 frontend 0 (STV0910)...
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.588598] DDBridge driver detected: Digital Devices Cine S2 V6.5 DVB adapter
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.589423] DDBridge: HW 0001000d REGMAP 00010004
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.591109] Port 0: Link 0, Link Port 0 (TAB 1): DUAL DVB-S2
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.699984] Port 1: Link 0, Link Port 1 (TAB 2): DUAL DVB-S2
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.808653] Port 2: Link 0, Link Port 2 (TAB 3): DUAL DVB-S2
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.909984] usb 3-3.1: new low-speed USB device number 3 using xhci_hcd
Aug 21 04:45:05 dvb-tams2 kernel: [ 5.917763] Port 3: Link 0, Link Port 3 (TAB 4): DUAL DVB-S2
-----------------
And this during tunning:
-----------------
Aug 21 04:50:31 dvb-tams2 kernel: [ 335.997919] tuner sleep
Aug 21 04:50:31 dvb-tams2 kernel: [ 335.998309] tuner sleep
Aug 21 04:50:31 dvb-tams2 kernel: [ 335.998750] sleep 1
Aug 21 04:50:31 dvb-tams2 kernel: [ 335.999403] tuner sleep
Aug 21 04:50:31 dvb-tams2 kernel: [ 335.999630] tuner sleep
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.000494] sleep 0
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.000496] tuner sleep
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.000933] sleep 0
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.001363] tuner sleep
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.001976] sleep 0
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.002356] tuner sleep
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.002362] sleep 1
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.002415] tuner sleep
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.003213] sleep 1
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.003704] sleep 0
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.004144] tuner sleep
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.004434] tuner sleep
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.004834] sleep 1
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.005568] sleep 0
Aug 21 04:50:31 dvb-tams2 kernel: [ 336.005884] sleep 1
Aug 21 04:50:56 dvb-tams2 kernel: [ 360.979348] init
Aug 21 04:50:56 dvb-tams2 kernel: [ 360.984277] init
Aug 21 04:50:56 dvb-tams2 kernel: [ 360.986318] init
Aug 21 04:50:56 dvb-tams2 kernel: [ 360.987005] init
Aug 21 04:50:56 dvb-tams2 kernel: [ 360.988641] init
Aug 21 04:50:56 dvb-tams2 kernel: [ 360.988733] init
Aug 21 04:50:56 dvb-tams2 kernel: [ 360.989130] init
Aug 21 04:50:56 dvb-tams2 kernel: [ 360.990351] init
Aug 21 04:50:56 dvb-tams2 kernel: [ 360.990445] init
Aug 21 04:50:56 dvb-tams2 kernel: [ 360.992777] init
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.383101] F = 1406000, COF = 19850000
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.390553] F = 1406000, COF = 19850000
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.390559] F = 1406000, COF = 19850000
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.391051] F = 1406000, COF = 19850000
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.392043] F = 1406000, COF = 19850000
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.404338] stv6111_regs = 08 41 8f 02 af 00 00 26 3b b1 11
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.404530] reg[] = 08 41 8f 02 af 00 00 26 3a bd 11
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.406148] F = 1406000, COF = 19850000
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.406632] symb = 10679
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.412797] stv6111_regs = 08 41 8f 02 af 00 00 26 3b b1 11
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.412806] stv6111_regs = 08 41 8f 02 af 00 00 26 3b b1 11
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.412807] reg[] = 08 41 8f 02 af 00 00 26 3a bd 11
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.412815] stv6111_regs = 08 41 8f 02 af 00 00 26 3b b1 11
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.412816] reg[] = 08 41 8f 02 af 00 00 26 3a bd 11
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.413030] stv6111_regs = 08 41 8f 02 af 00 00 26 3b b1 11
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.413031] reg[] = 08 41 8f 02 af 00 00 26 3a bd 11
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.414063] reg[] = 08 41 8f 02 af 00 00 26 3a bd 11
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.414362] F = 1406000, COF = 19850000
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.414556] F = 1406000, COF = 19850000
Aug 21 04:50:56 dvb-tams2 kernel: [ 361.414585] F = 1406000, COF = 19850000
A
-----------------
Norbert Auge wrote:
> Hello Anton,
> the driver for STV0910 does not support ToneBurst (=minidiseqc).
> If it is essential for you we can address this in our driver development
>
> best regards
> Dieter
>
> -----Ursprüngliche Nachricht-----
> Von: Anton Tinchev [mailto:atl@unixsol.org]
> Gesendet: Freitag, 21. August 2015 16:33
> An: Norbert Auge; linux-media@vger.kernel.org
> Cc: Georgi Chorbadzhiyski; Marian Zahariev
> Betreff: Bugs reporting
>
> Hi,
> can you point me where is usually reported the bugs with the cards firmware and/or drivers.
> The combination is Cine S2 v6.5 with Duoflex S2 V4.
>
> The miniDiSEqC (AB) is not working on the Duoflex S2 V4. Is not board fault, same behavior have all cards i tested - about 20 Duoflex and 8 Cine modules.
> For the protocol i tested:
>
> Cine S2 v6.5 + Duoflex S2 V4:
> - ports 0 and 1 (Ports on Cine card) - miniDiSEqC is working
> - ports 0 and 1 (Ports on Cine card) - DiSEqC is working
> - ports 2 and up (Ports on Duflex cards) - DiSEqC is working
> - ports 2 and up (Ports on Duflex cards) - miniDiSEqC is NOT WORKING
>
> Cine S2 v6.2 + Duoflex S2 older versions:
> - all ports - both Cine and Duoflex - miniDiSEqC is working
> - all ports - both Cine and Duoflex - DiSEqC is working
>
>
> Cine S2 v6.5 + Duoflex S2 older version:
> - Not tested, will test soon
>
> Cine S2 v6.2 + Duoflex S2 V4:
> - Not tested, will test when purchase next batch.
>
>
> Also there is tons of errors on i2c bus to Duoflex S2 V4 tabs.
>
>
>
> This was tested with latest drivers, also was tested with stock drivers with several kernel versions from 3.18.11 to 4.2 rc2 - same behavior
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* WG: Bugs reporting
[not found] ` <55DC448C.6090004@digitaldevices.de>
@ 2015-08-25 10:39 ` Norbert Auge
0 siblings, 0 replies; 4+ messages in thread
From: Norbert Auge @ 2015-08-25 10:39 UTC (permalink / raw)
To: atl, linux-media; +Cc: gf, marian
-----Ursprüngliche Nachricht-----
Von: Dieter Rimmele [mailto:drimmele@digitaldevices.de]
Gesendet: Dienstag, 25. August 2015 12:34
An: Norbert Auge
Betreff: Re: Bugs reporting
could you please try it again with MSI=0 as module parameter for DD Bridge when loading the driver.
> -----Ursprüngliche Nachricht-----
> Von: Anton Tinchev [mailto:atl@unixsol.org]
> Gesendet: Montag, 24. August 2015 18:40
> An: Norbert Auge; linux-media@vger.kernel.org
> Cc: 'Georgi Chorbadzhiyski'; 'Marian Zahariev'
> Betreff: Re: AW: Bugs reporting
>
> Hello.
> It is not critical (our multiswitches works with normal disqc too), but should be reported and taken care.
> Most important are the i2c errors i'm getting:
> This during module load
> ------------
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.518270] Attaching STV0900 demodulator(2) Cut=0x30
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.518597] LNBx2x attached on addr=8
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.519359] stv6110x_attach: Attaching STV6110x
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.519740] attach tuner input 1 adr 63
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.520160] ddbridge 0000:02:00.0: DVB: registering adapter 1 frontend 0 (STV090x Multistandard)...
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.523102] Found STV0910 id=0x51
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.524056] hub 2-1:1.0: USB hub found
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.524540] hub 2-1:1.0: 6 ports detected
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.529937] ndiv = 18, MasterClock = 135000000
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.540615] lnbh25: i2c_write error
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.541479] LNB25 on 0c
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.544768] attach_init OK
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.546639] stv6111_regs = 08 41 8f 12 ce 54 55 45 47 b5 11
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.547047] reg[] = 08 41 8f 02 ce 54 55 45 46 bd 11
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.548011] ddbridge 0000:02:00.0: DVB: registering adapter 2 frontend 0 (STV0910)...
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.549037] lnbh25: i2c_write error
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.549897] LNB25 on 0d
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.552078] attach_init OK
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.553953] stv6111_regs = 08 41 8f 12 ce 54 55 45 47 b5 11
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.554400] reg[] = 08 41 8f 02 ce 54 55 45 46 bd 11
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.555401] ddbridge 0000:02:00.0: DVB: registering adapter 3 frontend 0 (STV0910)...
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.557056] Found STV0910 id=0x51
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.563966] ndiv = 18, MasterClock = 135000000
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.573658] lnbh25: i2c_write error
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.574560] LNB25 on 0c
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.576780] attach_init OK
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.578680] stv6111_regs = 08 41 8f 12 ce 54 55 45 47 b5 11
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.579121] reg[] = 08 41 8f 02 ce 54 55 45 46 bd 11
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.580113] ddbridge 0000:02:00.0: DVB: registering adapter 4 frontend 0 (STV0910)...
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.581138] lnbh25: i2c_write error
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.582043] LNB25 on 0d
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.584268] attach_init OK
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.586166] stv6111_regs = 08 41 8f 12 ce 54 55 45 47 b5 11
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.586611] reg[] = 08 41 8f 02 ce 54 55 45 46 bd 11
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.587615] ddbridge 0000:02:00.0: DVB: registering adapter 5 frontend 0 (STV0910)...
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.588598] DDBridge driver detected: Digital Devices Cine S2 V6.5 DVB adapter
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.589423] DDBridge: HW 0001000d REGMAP 00010004
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.591109] Port 0: Link 0, Link Port 0 (TAB 1): DUAL DVB-S2
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.699984] Port 1: Link 0, Link Port 1 (TAB 2): DUAL DVB-S2
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.808653] Port 2: Link 0, Link Port 2 (TAB 3): DUAL DVB-S2
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.909984] usb 3-3.1: new low-speed USB device number 3 using xhci_hcd
> Aug 21 04:45:05 dvb-tams2 kernel: [ 5.917763] Port 3: Link 0, Link Port 3 (TAB 4): DUAL DVB-S2
> -----------------
> And this during tunning:
> -----------------
> Aug 21 04:50:31 dvb-tams2 kernel: [ 335.997919] tuner sleep Aug 21 04:50:31 dvb-tams2 kernel: [ 335.998309] tuner sleep Aug 21 04:50:31 dvb-tams2 kernel: [ 335.998750] sleep 1 Aug 21 04:50:31 dvb-tams2 kernel: [ 335.999403] tuner sleep Aug 21 04:50:31 dvb-tams2 kernel: [ 335.999630] tuner sleep Aug 21 04:50:31 dvb-tams2 kernel: [ 336.000494] sleep 0 Aug 21 04:50:31 dvb-tams2 kernel: [ 336.000496] tuner sleep Aug 21 04:50:31 dvb-tams2 kernel: [ 336.000933] sleep 0 Aug 21 04:50:31 dvb-tams2 kernel: [ 336.001363] tuner sleep Aug 21 04:50:31 dvb-tams2 kernel: [ 336.001976] sleep 0 Aug 21 04:50:31 dvb-tams2 kernel: [ 336.002356] tuner sleep Aug 21 04:50:31 dvb-tams2 kernel: [ 336.002362] sleep 1 Aug 21 04:50:31 dvb-tams2 kernel: [ 336.002415] tuner sleep Aug 21 04:50:31 dvb-tams2 kernel: [ 336.003213] sleep 1 Aug 21 04:50:31 dvb-tams2 kernel: [ 336.003704] sleep 0 Aug 21 04:50:31 dvb-tams2 kernel: [ 336.004144] tuner sleep Aug 21 04:50:31 dvb-tams2 kernel: [ 336.004434] tuner sleep Aug 21 04:50:31 dvb-tams2 kernel: [ 336.004834] sleep 1 Aug 21 04:50:31 dvb-tams2 kernel: [ 336.005568] sleep 0 Aug 21 04:50:31 dvb-tams2 kernel: [ 336.005884] sleep 1 Aug 21 04:50:56 dvb-tams2 kernel: [ 360.979348] init Aug 21 04:50:56 dvb-tams2 kernel: [ 360.984277] init Aug 21 04:50:56 dvb-tams2 kernel: [ 360.986318] init Aug 21 04:50:56 dvb-tams2 kernel: [ 360.987005] init Aug 21 04:50:56 dvb-tams2 kernel: [ 360.988641] init Aug 21 04:50:56 dvb-tams2 kernel: [ 360.988733] init Aug 21 04:50:56 dvb-tams2 kernel: [ 360.989130] init Aug 21 04:50:56 dvb-tams2 kernel: [ 360.990351] init Aug 21 04:50:56 dvb-tams2 kernel: [ 360.990445] init Aug 21 04:50:56 dvb-tams2 kernel: [ 360.992777] init Aug 21 04:50:56 dvb-tams2 kernel: [ 361.383101] F = 1406000, COF = 19850000 Aug 21 04:50:56 dvb-tams2 kernel: [ 361.390553] F = 1406000, COF = 19850000 Aug 21 04:50:56 dvb-tams2 kernel: [ 361.390559] F = 1406000, COF = 19850000 Aug 21 04:50:56 dvb-tams2 kernel: [ 361.391051] F = 1406000, COF = 19850000 Aug 21 04:50:56 dvb-tams2 kernel: [ 361.392043] F = 1406000, COF = 19850000 Aug 21 04:50:56 dvb-tams2 kernel: [ 361.404338] stv6111_regs = 08 41 8f 02 af 00 00 26 3b b1 11
> Aug 21 04:50:56 dvb-tams2 kernel: [ 361.404530] reg[] = 08 41 8f 02 af 00 00 26 3a bd 11
> Aug 21 04:50:56 dvb-tams2 kernel: [ 361.406148] F = 1406000, COF = 19850000 Aug 21 04:50:56 dvb-tams2 kernel: [ 361.406632] symb = 10679 Aug 21 04:50:56 dvb-tams2 kernel: [ 361.412797] stv6111_regs = 08 41 8f 02 af 00 00 26 3b b1 11 Aug 21 04:50:56 dvb-tams2 kernel: [ 361.412806] stv6111_regs = 08 41 8f 02 af 00 00 26 3b b1 11
> Aug 21 04:50:56 dvb-tams2 kernel: [ 361.412807] reg[] = 08 41 8f 02 af 00 00 26 3a bd 11
> Aug 21 04:50:56 dvb-tams2 kernel: [ 361.412815] stv6111_regs = 08 41 8f 02 af 00 00 26 3b b1 11
> Aug 21 04:50:56 dvb-tams2 kernel: [ 361.412816] reg[] = 08 41 8f 02 af 00 00 26 3a bd 11
> Aug 21 04:50:56 dvb-tams2 kernel: [ 361.413030] stv6111_regs = 08 41 8f 02 af 00 00 26 3b b1 11
> Aug 21 04:50:56 dvb-tams2 kernel: [ 361.413031] reg[] = 08 41 8f 02 af 00 00 26 3a bd 11
> Aug 21 04:50:56 dvb-tams2 kernel: [ 361.414063] reg[] = 08 41 8f 02 af 00 00 26 3a bd 11
> Aug 21 04:50:56 dvb-tams2 kernel: [ 361.414362] F = 1406000, COF =
> 19850000 Aug 21 04:50:56 dvb-tams2 kernel: [ 361.414556] F = 1406000,
> COF = 19850000 Aug 21 04:50:56 dvb-tams2 kernel: [ 361.414585] F =
> 1406000, COF = 19850000 A
> -----------------
>
>
> Norbert Auge wrote:
>> Hello Anton,
>> the driver for STV0910 does not support ToneBurst (=minidiseqc).
>> If it is essential for you we can address this in our driver
>> development
>>
>> best regards
>> Dieter
>>
>> -----Ursprüngliche Nachricht-----
>> Von: Anton Tinchev [mailto:atl@unixsol.org]
>> Gesendet: Freitag, 21. August 2015 16:33
>> An: Norbert Auge; linux-media@vger.kernel.org
>> Cc: Georgi Chorbadzhiyski; Marian Zahariev
>> Betreff: Bugs reporting
>>
>> Hi,
>> can you point me where is usually reported the bugs with the cards firmware and/or drivers.
>> The combination is Cine S2 v6.5 with Duoflex S2 V4.
>>
>> The miniDiSEqC (AB) is not working on the Duoflex S2 V4. Is not board fault, same behavior have all cards i tested - about 20 Duoflex and 8 Cine modules.
>> For the protocol i tested:
>>
>> Cine S2 v6.5 + Duoflex S2 V4:
>> - ports 0 and 1 (Ports on Cine card) - miniDiSEqC is working
>> - ports 0 and 1 (Ports on Cine card) - DiSEqC is working
>> - ports 2 and up (Ports on Duflex cards) - DiSEqC is working
>> - ports 2 and up (Ports on Duflex cards) - miniDiSEqC is NOT WORKING
>>
>> Cine S2 v6.2 + Duoflex S2 older versions:
>> - all ports - both Cine and Duoflex - miniDiSEqC is working
>> - all ports - both Cine and Duoflex - DiSEqC is working
>>
>>
>> Cine S2 v6.5 + Duoflex S2 older version:
>> - Not tested, will test soon
>>
>> Cine S2 v6.2 + Duoflex S2 V4:
>> - Not tested, will test when purchase next batch.
>>
>>
>> Also there is tons of errors on i2c bus to Duoflex S2 V4 tabs.
>>
>>
>>
>> This was tested with latest drivers, also was tested with stock
>> drivers with several kernel versions from 3.18.11 to 4.2 rc2 - same
>> behavior
>>
>
>
--
Linux4Media GmbH
Zussdorferstrasse 67
D-88271 Wilhelmsdorf
Tel.: +49(0)7503-9300 0
Fax.: +49(0)7503-9300 50
www.digitaldevices.de
drimmele@digitaldevices.de
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2015-08-25 10:37 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-08-21 14:32 Bugs reporting Anton Tinchev
2015-08-24 12:26 ` AW: " Norbert Auge
2015-08-24 16:39 ` Anton Tinchev
[not found] ` <00cd01d0df1f$d4da9760$7e8fc620$@digitaldevices.de>
[not found] ` <55DC448C.6090004@digitaldevices.de>
2015-08-25 10:39 ` WG: " Norbert Auge
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).