From: Bozhan Boiadzhiev <bozhan@abv.bg>
To: linux-dvb@linuxtv.org, video4linux-list@redhat.com
Subject: Re: [linux-dvb] ASUS My-Cinema remote patch
Date: Tue, 17 Jun 2008 22:28:24 +0300 (EEST) [thread overview]
Message-ID: <626861405.35803.1213730904672.JavaMail.apache@mail72.abv.bg> (raw)
whatever ...
adding option saa7134 card=78
solve all of my problems :)
my card doesn't have dvb but that is all difference with card 78
thanks
>-------- Оригинално писмо --------
>От: hermann pitton
>Относно: Re: Re: Re: [linux-dvb] ASUS My-Cinema remote patch
>До: Bozhan Boiadzhiev , linux-dvb@linuxtv.org, video4linux-list@redhat.com
>Изпратено на: Вторник, 2008, Юни 17 03:21:34 EEST
>Hi,
>
>Am Dienstag, den 17.06.2008, 00:42 +0300 schrieb Bozhan Boiadzhiev:
>> first of all
>> case SAA7134_BOARD_ASUSTeK_TVFM35:
>> must be
>> case SAA7134_BOARD_ASUSTeK_TVFM7135:
>> and second(result):
>
>of course, caused by at least faking it on a P7131_Dual previously and
>it seems I don't have all the devices in mind anymore ...
>
>> [ 27.947020] Linux video capture interface: v2.00
>> [ 28.018335] saa7130/34: v4l2 driver version 0.2.14 loaded
>> [ 28.018746] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 19
>> [ 28.018757] ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNKC] -> GSI 19 (level, low) -> IRQ 20
>> [ 28.018765] saa7133[0]: found at 0000:01:0a.0, rev: 208, irq: 20, latency: 32, mmio: 0xdffff800
>> [ 28.018770] saa7133[0]: subsystem: 1043:4845, board: ASUS TV-FM 7135 [card=53,autodetected]
>> [ 28.018785] saa7133[0]: board init: gpio is 40000
>> [ 28.168275] saa7133[0]: i2c eeprom 00: 43 10 45 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
>> [ 28.168284] saa7133[0]: i2c eeprom 10: 00 ff e2 0f ff 20 ff ff ff ff ff ff ff ff ff ff
>> [ 28.168290] saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 88 ff ff ff ff
>> [ 28.168296] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.168302] saa7133[0]: i2c eeprom 40: ff 22 00 c2 96 ff 02 30 15 ff ff ff ff ff ff ff
>> [ 28.168307] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.168313] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.168318] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.168324] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.168330] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.168335] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.168341] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.168346] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.168352] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.168358] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.168363] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> [ 28.404285] tuner' 2-004b: chip found @ 0x96 (saa7133[0])
>> [ 28.448222] saa7133[0]: P7131 analog only, using entry of ASUSTeK P7131 Analog
>> [ 28.528013] tda829x 2-004b: setting tuner address to 61
>> [ 28.655950] tda829x 2-004b: type set to tda8290+75a
>> [ 28.680922] NET: Registered protocol family 10
>> [ 28.681144] lo: Disabled Privacy Extensions
>> [ 29.067262] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input5
>> [ 32.489132] saa7133[0]: registered device video0 [v4l2]
>> [ 32.489154] saa7133[0]: registered device vbi0
>> [ 32.489175] saa7133[0]: registered device radio0
>> [ 32.552715] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 23
>> [ 32.552723] ACPI: PCI Interrupt 0000:00:05.0[B] -> Link [LAZA] -> GSI 23 (level, low) -> IRQ 16
>> [ 32.552748] PCI: Setting latency timer of device 0000:00:05.0 to 64
>> [ 32.588072] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
>> [ 32.599962] saa7134_alsa: disagrees about version of symbol saa7134_tvaudio_setmute
>> [ 32.599968] saa7134_alsa: Unknown symbol saa7134_tvaudio_setmute
>> [ 32.600067] saa7134_alsa: disagrees about version of symbol saa_dsp_writel
>> [ 32.600069] saa7134_alsa: Unknown symbol saa_dsp_writel
>> [ 32.600181] saa7134_alsa: disagrees about version of symbol videobuf_dma_free
>> [ 32.600183] saa7134_alsa: Unknown symbol videobuf_dma_free
>> [ 32.600298] saa7134_alsa: disagrees about version of symbol saa7134_pgtable_alloc
>> [ 32.600300] saa7134_alsa: Unknown symbol saa7134_pgtable_alloc
>> [ 32.600332] saa7134_alsa: disagrees about version of symbol saa7134_pgtable_build
>> [ 32.600334] saa7134_alsa: Unknown symbol saa7134_pgtable_build
>> [ 32.600360] saa7134_alsa: disagrees about version of symbol saa7134_pgtable_free
>> [ 32.600362] saa7134_alsa: Unknown symbol saa7134_pgtable_free
>> [ 32.600389] saa7134_alsa: disagrees about version of symbol saa7134_dmasound_init
>> [ 32.600391] saa7134_alsa: Unknown symbol saa7134_dmasound_init
>> [ 32.600477] saa7134_alsa: disagrees about version of symbol saa7134_dmasound_exit
>> [ 32.600478] saa7134_alsa: Unknown symbol saa7134_dmasound_exit
>> [ 32.600540] saa7134_alsa: disagrees about version of symbol videobuf_dma_init
>> [ 32.600542] saa7134_alsa: Unknown symbol videobuf_dma_init
>> [ 32.600633] saa7134_alsa: disagrees about version of symbol videobuf_dma_init_kernel
>> [ 32.600635] saa7134_alsa: Unknown symbol videobuf_dma_init_kernel
>> [ 32.600710] saa7134_alsa: Unknown symbol videobuf_pci_dma_unmap
>> [ 32.600796] saa7134_alsa: Unknown symbol videobuf_pci_dma_map
>> [ 32.600828] saa7134_alsa: disagrees about version of symbol saa7134_set_dmabits
>> [ 32.600830] saa7134_alsa: Unknown symbol saa7134_set_dmabits
>> [ 33.623299] lp: driver loaded but no devices found
>> [ 33.773941] Adding 859436k swap on /dev/sda5. Priority:-1 extents:1 across:859436k
>>
>>
>> and ...:)
>> no sound :)
>
>Did you upgrade to some recent Ubuntu in between?
>You don't have the on board analog audio out connected and are depending
>on saa7134-alsa?
>
>Analog audio and saa7134-alsa was tested on my fake stuff, also that DVB
>is not registered and should work.
>
>> aa and no one more input device either
>
>This is more serious and brain damage by me, improved by faking the
>device. Since you have no IR registered on your device, the Dual has,
>we can't "steel" it and that fails here.
>
>Force card=145 for now. No sure what to try next yet.
>
>> thanks
>>
>> >-------- Оригинално писмо --------
>> >От: hermann pitton
>> >Относно: Re: Re: [linux-dvb] ASUS My-Cinema remote patch
>> >До: Bozhan Boiadzhiev , Hartmut Hackmann , Mauro Carvalho Chehab
>> >Изпратено на: Неделя, 2008, Юни 15 23:34:35 EEST
>>
>> >Hi,
>> >
>> >Am Sonntag, den 15.06.2008, 13:03 +0300 schrieb Bozhan Boiadzhiev:
>> >>
>> >> ok i'll test patch later.
>> >> thanks
>> >> :)
>> >
>> >here is an updated version after latest changes by Matthias and Tim on
>> >saa7134. Should work.
>> >
>> >Can't do much more on it.
>> >
>> >Hartmut, Mauro, the eeprom detection is very basic, but should work. I
>> >sign off so far. Also attached.
>> >
>> >Cheers,
>> >Hermann
>> >
>> >saa7134: add a separate entry for the ASUSTeK P7131 analog only
>> > and do some eeprom detection to escape from the TVFM35
>> > with the same PCI subsystem on auto detection.
>
>Many thanks to Bozhan Boiadzhiev for testing and reporting.
>
>Recent version attached, but not ready yet for IR on auto detection.
>
>> >
>> >Signed-off-by: Hermann Pitton
>> >
>[snip]
>> >
>> >> >-------- Оригинално писмо --------
>> >> >От: hermann pitton
>> >> >Относно: Re: [linux-dvb] ASUS My-Cinema remote patch
>> >> >До: Bozhan Boiadzhiev
>> >> >Изпратено на: Неделя, 2008, Юни 15 04:53:14 EEST
>> >>
>> >> >Hi Bozhan,
>> >> >
>> >> >Am Samstag, den 14.06.2008, 23:44 +0300 schrieb Bozhan Boiadzhiev:
>> >> >> ASUS My-Cinema package include remote
>> >> >> here i found patch for 2.6.22 https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.22/+bug/141622
>> >> >> Please include it!
>> >> >> All ASUS My-Cinema comes with remote control.
>> >> >> Thanks.
>> >> >>
>> >> >
>> >> >the video4linux-list is the better place for analog only cards.
>> >> >
>> >> >The problem is known, but we had no testers.
>> >> >
>> >> >The old Asus TVFM35 is not identical to your card.
>> >> >
>> >> >It seems to have different s-video and composite inputs and also came
>> >> >with an USB remote. Adding a new, on the old card not present remote now
>> >> >there, seems to be confusing for the users.
>> >> >
>> >> >The new tuner type tda8275a is auto detected, that makes the old entry
>> >> >working for you. It has the previous tda8275 not "a".
>> >> >
>> >> >The problem is the unchanged PCI subsystem on your card, which causes
>> >> >that it is autodetected as card=53.
>> >> >
>> >> >The following untested patch is a first try to detect your card and add
>> >> >a separate entry for it. We discussed this once.
>> >> >
>> >> >Cheers,
>> >> >Hermann
>> >>
>
>
>
>
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
next reply other threads:[~2008-06-17 19:28 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-06-17 19:28 Bozhan Boiadzhiev [this message]
2008-06-17 22:14 ` [linux-dvb] ASUS My-Cinema remote patch hermann pitton
-- strict thread matches above, loose matches on Subject: below --
2008-06-24 3:07 Diego V. Martinez
2008-06-24 21:35 ` hermann pitton
2008-06-23 15:52 Diego V. Martinez
2008-06-23 22:07 ` hermann pitton
2008-06-15 10:03 Bozhan Boiadzhiev
[not found] ` <1213562075.2683.79.camel@pc10.localdom.local>
2008-07-12 12:29 ` Mauro Carvalho Chehab
2008-07-12 21:18 ` hermann pitton
[not found] ` <1215897249.2987.28.camel@pc10.localdom.local>
2008-07-17 22:55 ` Mauro Carvalho Chehab
2008-06-14 20:44 Bozhan Boiadzhiev
2008-06-15 1:53 ` hermann pitton
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=626861405.35803.1213730904672.JavaMail.apache@mail72.abv.bg \
--to=bozhan@abv.bg \
--cc=linux-dvb@linuxtv.org \
--cc=video4linux-list@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox