Re: [PATCH v2 1/2] [media] imx214: device tree binding

[Laurent Pinchart <laurent.pinchart@ideasonboard.com>]

Hi Ricardo,

Thank you for the patch.

On Friday, 21 September 2018 13:09:19 EEST Ricardo Ribalda Delgado wrote:
> Document bindings for imx214 v4l2 driver.

Those are bindings for the IMX214 camera sensor, not for its V4L2 driver.

> Cc: devicetree@vger.kernel.org
> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
> ---
>  .../devicetree/bindings/media/i2c/imx214.txt  | 51 +++++++++++++++++++
>  1 file changed, 51 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/imx214.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/imx214.txt
> b/Documentation/devicetree/bindings/media/i2c/imx214.txt new file mode
> 100644
> index 000000000000..4ff76d96332e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/imx214.txt
> @@ -0,0 +1,51 @@
> +* Sony 1/3.06-Inch 13.13Mp CMOS Digital Image Sensor
> +
> +The Sony imx214 is a 1/3.06-inch CMOS active pixel digital image sensor
> with +an active array size of 4224H x 3176V. It is programmable through I2C
> +interface.

s/I2C interface/an I2C interface/

> The I2C address can be configured to to 0x1a or 0x10, depending
> on +how is wired.

Maybe "depending on how the hardware is wired" ?

> +Image data is sent through MIPI CSI-2, which is configured as 4 lanes
> +at 1440 Mbps.

Can the sensor use less lanes than 4, or is it fixed ?

> +Required Properties:
> +- compatible: value should be "sony,imx214" for imx214 sensor
> +- reg: I2C bus address of the device
> +- enable-gpios: Sensor enable GPIO

Maybe "GPIO descriptor for the enable pin" ?

> +- vdddo-supply: Chip digital IO regulator (1.8V).
> +- vdda-supply: Chip analog regulator (2.7V).
> +- vddd-supply: Chip digital core regulator (1.12V).
> +- clocks = Reference to the xclk clock.
> +- clock-names = Should be "xclk".

If there's a single clock, is the name mandatory ?

> +- clock-frequency = Frequency of the xclk clock. Should be <24000000>;

The frequency of the clock can be queried at runtime. If you want to hardcode 
a specific frequency in DT, you should use the assigned-clock-rates property.

> +Optional Properties:
> +- flash-leds: See ../video-interfaces.txt
> +- lens-focus: See ../video-interfaces.txt
> +
> +The imx274 device node should contain one 'port' child node with
> +an 'endpoint' subnode. For further reading on port node refer to
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Example:
> +
> +	camera_rear@1a {
> +		status = "okay";

Isn't that the default ?

> +		compatible = "sony,imx214";
> +		reg = <0x1a>;
> +		vdddo-supply = <&pm8994_lvs1>;
> +		vddd-supply = <&camera_vddd_1v12>;
> +		vdda-supply = <&pm8994_l17>;
> +		lens-focus = <&ad5820>;
> +		enable-gpios = <&msmgpio 25 GPIO_ACTIVE_HIGH>;
> +		clocks = <&mmcc CAMSS_MCLK0_CLK>;
> +		clock-names = "xclk";
> +		clock-frequency = <24000000>;
> +		port {
> +				imx214_ep: endpoint {

Incorrect indentation ?

> +				clock-lanes = <1>;
> +				data-lanes = <0 2 3 4>;

Those properties are not documented. The data-lanes value is peculiar, does 
the sensor support lanes remapping ?

> +				remote-endpoint = <&csiphy0_ep>;
> +			};
> +		};
> +	};


-- 
Regards,

Laurent Pinchart