From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
linux-media@vger.kernel.org,
Alexander Stein <alexander.stein@ew.tq-group.com>
Subject: Re: [PATCH v2 12/13] media: i2c: imx290: Add support for H & V Flips
Date: Tue, 7 Feb 2023 03:52:53 +0200 [thread overview]
Message-ID: <Y+Gu9aSaY8NJVCcs@pendragon.ideasonboard.com> (raw)
In-Reply-To: <20230203191811.947697-13-dave.stevenson@raspberrypi.com>
Hi Dave,
Thank you for the patch.
On Fri, Feb 03, 2023 at 07:18:10PM +0000, Dave Stevenson wrote:
> The sensor supports H & V flips, so add the relevant hooks for
> V4L2_CID_HFLIP and V4L2_CID_VFLIP to configure them.
>
> Note that the Bayer order is maintained as the readout area
> shifts by 1 pixel in the appropriate direction (note the
> comment about the top margin being 8 pixels whilst the bottom
> margin is 9). The V4L2_SEL_TGT_CROP region is therefore
> adjusted appropriately.
>
> Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> ---
> drivers/media/i2c/imx290.c | 51 ++++++++++++++++++++++++++++++++++----
> 1 file changed, 46 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c
> index 045d27b4d31b..7167eb1edb9b 100644
> --- a/drivers/media/i2c/imx290.c
> +++ b/drivers/media/i2c/imx290.c
> @@ -208,6 +208,7 @@ struct imx290_mode {
> u32 hmax_min;
> u32 vmax_min;
> u8 link_freq_index;
> + u8 ctrl_07;
>
> const struct imx290_regval *data;
> u32 data_size;
> @@ -248,6 +249,10 @@ struct imx290 {
> struct v4l2_ctrl *hblank;
> struct v4l2_ctrl *vblank;
> struct v4l2_ctrl *exposure;
> + struct {
> + struct v4l2_ctrl *hflip;
> + struct v4l2_ctrl *vflip;
> + };
> };
>
> static inline struct imx290 *to_imx290(struct v4l2_subdev *_sd)
> @@ -325,7 +330,6 @@ static const struct imx290_regval xclk_regs[][IMX290_NUM_CLK_REGS] = {
>
> static const struct imx290_regval imx290_1080p_settings[] = {
> /* mode settings */
> - { IMX290_CTRL_07, IMX290_WINMODE_1080P },
> { IMX290_WINWV_OB, 12 },
> { IMX290_OPB_SIZE_V, 10 },
> { IMX290_X_OUT_SIZE, 1920 },
> @@ -334,7 +338,6 @@ static const struct imx290_regval imx290_1080p_settings[] = {
>
> static const struct imx290_regval imx290_720p_settings[] = {
> /* mode settings */
> - { IMX290_CTRL_07, IMX290_WINMODE_720P },
> { IMX290_WINWV_OB, 6 },
> { IMX290_OPB_SIZE_V, 4 },
> { IMX290_X_OUT_SIZE, 1280 },
> @@ -494,6 +497,7 @@ static const struct imx290_mode imx290_modes_2lanes[] = {
> .hmax_min = 2200,
> .vmax_min = 1125,
> .link_freq_index = FREQ_INDEX_1080P,
> + .ctrl_07 = IMX290_WINMODE_1080P,
> .data = imx290_1080p_settings,
> .data_size = ARRAY_SIZE(imx290_1080p_settings),
> .clk_cfg = imx290_1080p_clock_config,
> @@ -504,6 +508,7 @@ static const struct imx290_mode imx290_modes_2lanes[] = {
> .hmax_min = 3300,
> .vmax_min = 750,
> .link_freq_index = FREQ_INDEX_720P,
> + .ctrl_07 = IMX290_WINMODE_720P,
> .data = imx290_720p_settings,
> .data_size = ARRAY_SIZE(imx290_720p_settings),
> .clk_cfg = imx290_720p_clock_config,
> @@ -517,6 +522,7 @@ static const struct imx290_mode imx290_modes_4lanes[] = {
> .hmax_min = 2200,
> .vmax_min = 1125,
> .link_freq_index = FREQ_INDEX_1080P,
> + .ctrl_07 = IMX290_WINMODE_1080P,
> .data = imx290_1080p_settings,
> .data_size = ARRAY_SIZE(imx290_1080p_settings),
> .clk_cfg = imx290_1080p_clock_config,
> @@ -527,6 +533,7 @@ static const struct imx290_mode imx290_modes_4lanes[] = {
> .hmax_min = 3300,
> .vmax_min = 750,
> .link_freq_index = FREQ_INDEX_720P,
> + .ctrl_07 = IMX290_WINMODE_720P,
> .data = imx290_720p_settings,
> .data_size = ARRAY_SIZE(imx290_720p_settings),
> .clk_cfg = imx290_720p_clock_config,
> @@ -835,6 +842,20 @@ static int imx290_set_ctrl(struct v4l2_ctrl *ctrl)
> NULL);
> break;
>
> + case V4L2_CID_HFLIP:
> + case V4L2_CID_VFLIP:
> + {
> + u32 reg;
> +
> + reg = imx290->current_mode->ctrl_07;
> + if (imx290->hflip->val)
> + reg |= IMX290_HREVERSE;
> + if (imx290->vflip->val)
> + reg |= IMX290_VREVERSE;
> + ret = imx290_write(imx290, IMX290_CTRL_07, reg, NULL);
> + break;
> + }
> +
> default:
> ret = -EINVAL;
> break;
> @@ -887,7 +908,7 @@ static int imx290_ctrl_init(struct imx290 *imx290)
> if (ret < 0)
> return ret;
>
> - v4l2_ctrl_handler_init(&imx290->ctrls, 9);
> + v4l2_ctrl_handler_init(&imx290->ctrls, 11);
>
> /*
> * The sensor has an analog gain and a digital gain, both controlled
> @@ -944,6 +965,12 @@ static int imx290_ctrl_init(struct imx290 *imx290)
> imx290->vblank = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops,
> V4L2_CID_VBLANK, 1, 1, 1, 1);
>
> + imx290->hflip = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops,
> + V4L2_CID_HFLIP, 0, 1, 1, 0);
> + imx290->vflip = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops,
> + V4L2_CID_VFLIP, 0, 1, 1, 0);
> + v4l2_ctrl_cluster(2, &imx290->hflip);
> +
> v4l2_ctrl_new_fwnode_properties(&imx290->ctrls, &imx290_ctrl_ops,
> &props);
>
> @@ -1065,6 +1092,13 @@ static int imx290_set_stream(struct v4l2_subdev *sd, int enable)
> pm_runtime_put_autosuspend(imx290->dev);
> }
>
> + /*
> + * vflip and hflip should not be changed during streaming as the sensor
> + * will produce an invalid frame.
> + */
> + __v4l2_ctrl_grab(imx290->vflip, enable);
> + __v4l2_ctrl_grab(imx290->hflip, enable);
> +
> unlock:
> v4l2_subdev_unlock_state(state);
> return ret;
> @@ -1147,16 +1181,23 @@ static int imx290_get_selection(struct v4l2_subdev *sd,
> struct v4l2_subdev_state *sd_state,
> struct v4l2_subdev_selection *sel)
> {
> + struct imx290 *imx290 = to_imx290(sd);
> struct v4l2_mbus_framefmt *format;
>
> switch (sel->target) {
> case V4L2_SEL_TGT_CROP: {
> format = v4l2_subdev_get_pad_format(sd, sd_state, 0);
>
> + /*
> + * The sensor moves the readout by 1 pixel based on flips to
> + * keep the Bayer order the same.
> + */
> sel->r.top = IMX920_PIXEL_ARRAY_MARGIN_TOP
> - + (IMX290_PIXEL_ARRAY_RECORDING_HEIGHT - format->height) / 2;
> + + (IMX290_PIXEL_ARRAY_RECORDING_HEIGHT - format->height) / 2
> + + imx290->vflip->val;
> sel->r.left = IMX920_PIXEL_ARRAY_MARGIN_LEFT
> - + (IMX290_PIXEL_ARRAY_RECORDING_WIDTH - format->width) / 2;
> + + (IMX290_PIXEL_ARRAY_RECORDING_WIDTH - format->width) / 2
> + + imx290->hflip->val;
> sel->r.width = format->width;
> sel->r.height = format->height;
>
--
Regards,
Laurent Pinchart
next prev parent reply other threads:[~2023-02-07 1:53 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-02-03 19:17 [PATCH v2 00/13] imx290: Minor fixes, support for alternate INCK, and more ctrls Dave Stevenson
2023-02-03 19:17 ` [PATCH v2 01/13] media: i2c: imx290: Match kernel coding style on whitespace Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 02/13] media: i2c: imx290: Set the colorspace fields in the format Dave Stevenson
2023-02-07 1:34 ` Laurent Pinchart
2023-02-03 19:18 ` [PATCH v2 03/13] media: i2c: imx290: Add V4L2_SUBDEV_FL_HAS_EVENTS and subscribe hooks Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 04/13] media: i2c: imx290: Fix the pixel rate at 148.5Mpix/s Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 05/13] media: i2c: imx290: Support 60fps in 2 lane operation Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 06/13] media: i2c: imx290: Use CSI timings as per datasheet Dave Stevenson
2023-02-06 7:48 ` Alexander Stein
2023-02-03 19:18 ` [PATCH v2 07/13] media: i2c: imx290: Convert V4L2_CID_HBLANK to read/write Dave Stevenson
2023-02-06 7:59 ` Alexander Stein
2023-02-03 19:18 ` [PATCH v2 08/13] media: i2c: imx290: Convert V4L2_CID_VBLANK " Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 09/13] media: i2c: imx290: VMAX is mode dependent Dave Stevenson
2023-02-07 1:46 ` Laurent Pinchart
2023-02-03 19:18 ` [PATCH v2 10/13] media: i2c: imx290: Remove duplicated write to IMX290_CTRL_07 Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 11/13] media: i2c: imx290: Add support for 74.25MHz external clock Dave Stevenson
2023-02-06 8:24 ` Alexander Stein
2023-02-07 1:50 ` Laurent Pinchart
2023-02-03 19:18 ` [PATCH v2 12/13] media: i2c: imx290: Add support for H & V Flips Dave Stevenson
2023-02-07 1:52 ` Laurent Pinchart [this message]
2023-02-03 19:18 ` [PATCH v2 13/13] media: i2c: imx290: Add the error code to logs in start_streaming Dave Stevenson
2023-02-06 8:27 ` Alexander Stein
2023-02-07 1:53 ` Laurent Pinchart
2023-02-07 1:55 ` [PATCH v2 00/13] imx290: Minor fixes, support for alternate INCK, and more ctrls Laurent Pinchart
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Y+Gu9aSaY8NJVCcs@pendragon.ideasonboard.com \
--to=laurent.pinchart@ideasonboard.com \
--cc=alexander.stein@ew.tq-group.com \
--cc=dave.stevenson@raspberrypi.com \
--cc=linux-media@vger.kernel.org \
--cc=mani@kernel.org \
--cc=mchehab@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox