From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
linux-media@vger.kernel.org,
Alexander Stein <alexander.stein@ew.tq-group.com>
Subject: Re: [PATCH v2 11/13] media: i2c: imx290: Add support for 74.25MHz external clock
Date: Tue, 7 Feb 2023 03:50:02 +0200 [thread overview]
Message-ID: <Y+GuSqapyqV+Lp9b@pendragon.ideasonboard.com> (raw)
In-Reply-To: <20230203191811.947697-12-dave.stevenson@raspberrypi.com>
Hi Dave,
Thank you for the patch.
On Fri, Feb 03, 2023 at 07:18:09PM +0000, Dave Stevenson wrote:
> The sensor supports either a 37.125 or 74.25MHz external, but
> the driver only supported 37.125MHz.
>
> Add the relevant register configuration for either clock
> frequency option.
>
> Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> ---
> drivers/media/i2c/imx290.c | 132 ++++++++++++++++++++++++++++++++-----
> 1 file changed, 116 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c
> index a74930e86a6c..045d27b4d31b 100644
> --- a/drivers/media/i2c/imx290.c
> +++ b/drivers/media/i2c/imx290.c
> @@ -102,6 +102,7 @@
> #define IMX290_TCLKPREPARE IMX290_REG_16BIT(0x3452)
> #define IMX290_TLPX IMX290_REG_16BIT(0x3454)
> #define IMX290_X_OUT_SIZE IMX290_REG_16BIT(0x3472)
> +#define IMX290_INCKSEL7 IMX290_REG_8BIT(0x3480)
>
> #define IMX290_PGCTRL_REGEN BIT(0)
> #define IMX290_PGCTRL_THRU BIT(1)
> @@ -178,11 +179,29 @@ struct imx290_model_info {
> enum imx290_colour_variant colour_variant;
> };
>
> +enum imx290_clk_freq {
> + IMX290_CLK_37_125,
> + IMX290_CLK_74_25,
> + IMX290_NUM_CLK
> +};
> +
> struct imx290_regval {
> u32 reg;
> u32 val;
> };
>
> +/*
> + * Clock configuration for registers INCKSEL1 to INCKSEL6.
> + */
> +struct imx290_clk_cfg {
> + u8 incksel1;
> + u8 incksel2;
> + u8 incksel3;
> + u8 incksel4;
> + u8 incksel5;
> + u8 incksel6;
> +};
> +
> struct imx290_mode {
> u32 width;
> u32 height;
> @@ -192,6 +211,8 @@ struct imx290_mode {
>
> const struct imx290_regval *data;
> u32 data_size;
> +
> + const struct imx290_clk_cfg *clk_cfg;
> };
>
> struct imx290_csi_cfg {
> @@ -210,6 +231,7 @@ struct imx290 {
> struct device *dev;
> struct clk *xclk;
> struct regmap *regmap;
> + enum imx290_clk_freq xclk_idx;
> u8 nlanes;
> const struct imx290_model_info *model;
>
> @@ -238,7 +260,6 @@ static inline struct imx290 *to_imx290(struct v4l2_subdev *_sd)
> */
>
> static const struct imx290_regval imx290_global_init_settings[] = {
> - { IMX290_EXTCK_FREQ, 0x2520 },
> { IMX290_WINWV_OB, 12 },
> { IMX290_WINPH, 0 },
> { IMX290_WINPV, 0 },
> @@ -288,7 +309,18 @@ static const struct imx290_regval imx290_global_init_settings[] = {
> { IMX290_REG_8BIT(0x33b0), 0x50 },
> { IMX290_REG_8BIT(0x33b2), 0x1a },
> { IMX290_REG_8BIT(0x33b3), 0x04 },
> - { IMX290_REG_8BIT(0x3480), 0x49 },
> +};
> +
> +#define IMX290_NUM_CLK_REGS 2
> +static const struct imx290_regval xclk_regs[][IMX290_NUM_CLK_REGS] = {
> + [IMX290_CLK_37_125] = {
> + { IMX290_EXTCK_FREQ, (37125 * 256) / 1000 },
> + { IMX290_INCKSEL7, 0x49 },
> + },
> + [IMX290_CLK_74_25] = {
> + { IMX290_EXTCK_FREQ, (74250 * 256) / 1000 },
> + { IMX290_INCKSEL7, 0x92 },
> + },
> };
>
> static const struct imx290_regval imx290_1080p_settings[] = {
> @@ -298,12 +330,6 @@ static const struct imx290_regval imx290_1080p_settings[] = {
> { IMX290_OPB_SIZE_V, 10 },
> { IMX290_X_OUT_SIZE, 1920 },
> { IMX290_Y_OUT_SIZE, 1080 },
> - { IMX290_INCKSEL1, 0x18 },
> - { IMX290_INCKSEL2, 0x03 },
> - { IMX290_INCKSEL3, 0x20 },
> - { IMX290_INCKSEL4, 0x01 },
> - { IMX290_INCKSEL5, 0x1a },
> - { IMX290_INCKSEL6, 0x1a },
> };
>
> static const struct imx290_regval imx290_720p_settings[] = {
> @@ -313,12 +339,6 @@ static const struct imx290_regval imx290_720p_settings[] = {
> { IMX290_OPB_SIZE_V, 4 },
> { IMX290_X_OUT_SIZE, 1280 },
> { IMX290_Y_OUT_SIZE, 720 },
> - { IMX290_INCKSEL1, 0x20 },
> - { IMX290_INCKSEL2, 0x00 },
> - { IMX290_INCKSEL3, 0x20 },
> - { IMX290_INCKSEL4, 0x01 },
> - { IMX290_INCKSEL5, 0x1a },
> - { IMX290_INCKSEL6, 0x1a },
> };
>
> static const struct imx290_regval imx290_10bit_settings[] = {
> @@ -424,6 +444,48 @@ static inline int imx290_link_freqs_num(const struct imx290 *imx290)
> return ARRAY_SIZE(imx290_link_freq_4lanes);
> }
>
> +static const struct imx290_clk_cfg imx290_1080p_clock_config[] = {
> + [IMX290_CLK_37_125] = {
> + /* 37.125MHz clock config */
> + .incksel1 = 0x18,
> + .incksel2 = 0x03,
> + .incksel3 = 0x20,
> + .incksel4 = 0x01,
> + .incksel5 = 0x1a,
> + .incksel6 = 0x1a,
> + },
> + [IMX290_CLK_74_25] = {
> + /* 74.25MHz clock config */
> + .incksel1 = 0x0c,
> + .incksel2 = 0x03,
> + .incksel3 = 0x10,
> + .incksel4 = 0x01,
> + .incksel5 = 0x1b,
> + .incksel6 = 0x1b,
> + },
> +};
> +
> +static const struct imx290_clk_cfg imx290_720p_clock_config[] = {
> + [IMX290_CLK_37_125] = {
> + /* 37.125MHz clock config */
> + .incksel1 = 0x20,
> + .incksel2 = 0x00,
> + .incksel3 = 0x20,
> + .incksel4 = 0x01,
> + .incksel5 = 0x1a,
> + .incksel6 = 0x1a,
> + },
> + [IMX290_CLK_74_25] = {
> + /* 74.25MHz clock config */
> + .incksel1 = 0x10,
> + .incksel2 = 0x00,
> + .incksel3 = 0x10,
> + .incksel4 = 0x01,
> + .incksel5 = 0x1b,
> + .incksel6 = 0x1b,
> + },
> +};
> +
> /* Mode configs */
> static const struct imx290_mode imx290_modes_2lanes[] = {
> {
> @@ -434,6 +496,7 @@ static const struct imx290_mode imx290_modes_2lanes[] = {
> .link_freq_index = FREQ_INDEX_1080P,
> .data = imx290_1080p_settings,
> .data_size = ARRAY_SIZE(imx290_1080p_settings),
> + .clk_cfg = imx290_1080p_clock_config,
> },
> {
> .width = 1280,
> @@ -443,6 +506,7 @@ static const struct imx290_mode imx290_modes_2lanes[] = {
> .link_freq_index = FREQ_INDEX_720P,
> .data = imx290_720p_settings,
> .data_size = ARRAY_SIZE(imx290_720p_settings),
> + .clk_cfg = imx290_720p_clock_config,
> },
> };
>
> @@ -455,6 +519,7 @@ static const struct imx290_mode imx290_modes_4lanes[] = {
> .link_freq_index = FREQ_INDEX_1080P,
> .data = imx290_1080p_settings,
> .data_size = ARRAY_SIZE(imx290_1080p_settings),
> + .clk_cfg = imx290_1080p_clock_config,
> },
> {
> .width = 1280,
> @@ -464,6 +529,7 @@ static const struct imx290_mode imx290_modes_4lanes[] = {
> .link_freq_index = FREQ_INDEX_720P,
> .data = imx290_720p_settings,
> .data_size = ARRAY_SIZE(imx290_720p_settings),
> + .clk_cfg = imx290_720p_clock_config,
> },
> };
>
> @@ -587,6 +653,26 @@ static int imx290_set_register_array(struct imx290 *imx290,
> return 0;
> }
>
> +static int imx290_set_clock(struct imx290 *imx290)
> +{
> + const struct imx290_mode *mode = imx290->current_mode;
> + enum imx290_clk_freq clk_idx = imx290->xclk_idx;
> + const struct imx290_clk_cfg *clk_cfg = &mode->clk_cfg[clk_idx];
> + int ret;
> +
> + ret = imx290_set_register_array(imx290, xclk_regs[clk_idx],
> + IMX290_NUM_CLK_REGS);
> +
> + imx290_write(imx290, IMX290_INCKSEL1, clk_cfg->incksel1, &ret);
> + imx290_write(imx290, IMX290_INCKSEL2, clk_cfg->incksel2, &ret);
> + imx290_write(imx290, IMX290_INCKSEL3, clk_cfg->incksel3, &ret);
> + imx290_write(imx290, IMX290_INCKSEL4, clk_cfg->incksel4, &ret);
> + imx290_write(imx290, IMX290_INCKSEL5, clk_cfg->incksel5, &ret);
> + imx290_write(imx290, IMX290_INCKSEL6, clk_cfg->incksel6, &ret);
> +
> + return ret;
> +}
> +
> static int imx290_set_data_lanes(struct imx290 *imx290)
> {
> int ret = 0;
> @@ -891,6 +977,13 @@ static int imx290_start_streaming(struct imx290 *imx290,
> return ret;
> }
>
> + /* Set clock parameters based on mode and xclk */
> + ret = imx290_set_clock(imx290);
> + if (ret < 0) {
> + dev_err(imx290->dev, "Could not set clocks\n");
> + return ret;
> + }
> +
> /* Set data lane count */
> ret = imx290_set_data_lanes(imx290);
> if (ret < 0) {
> @@ -1290,8 +1383,15 @@ static int imx290_init_clk(struct imx290 *imx290)
> return ret;
> }
>
> - /* external clock must be 37.125 MHz */
> - if (xclk_freq != 37125000) {
> + /* external clock must be 37.125 MHz or 74.25MHz */
> + switch (xclk_freq) {
> + case 37125000:
> + imx290->xclk_idx = IMX290_CLK_37_125;
> + break;
> + case 74250000:
> + imx290->xclk_idx = IMX290_CLK_74_25;
> + break;
> + default:
> dev_err(imx290->dev, "External clock frequency %u is not supported\n",
> xclk_freq);
> return -EINVAL;
--
Regards,
Laurent Pinchart
next prev parent reply other threads:[~2023-02-07 1:50 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-02-03 19:17 [PATCH v2 00/13] imx290: Minor fixes, support for alternate INCK, and more ctrls Dave Stevenson
2023-02-03 19:17 ` [PATCH v2 01/13] media: i2c: imx290: Match kernel coding style on whitespace Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 02/13] media: i2c: imx290: Set the colorspace fields in the format Dave Stevenson
2023-02-07 1:34 ` Laurent Pinchart
2023-02-03 19:18 ` [PATCH v2 03/13] media: i2c: imx290: Add V4L2_SUBDEV_FL_HAS_EVENTS and subscribe hooks Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 04/13] media: i2c: imx290: Fix the pixel rate at 148.5Mpix/s Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 05/13] media: i2c: imx290: Support 60fps in 2 lane operation Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 06/13] media: i2c: imx290: Use CSI timings as per datasheet Dave Stevenson
2023-02-06 7:48 ` Alexander Stein
2023-02-03 19:18 ` [PATCH v2 07/13] media: i2c: imx290: Convert V4L2_CID_HBLANK to read/write Dave Stevenson
2023-02-06 7:59 ` Alexander Stein
2023-02-03 19:18 ` [PATCH v2 08/13] media: i2c: imx290: Convert V4L2_CID_VBLANK " Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 09/13] media: i2c: imx290: VMAX is mode dependent Dave Stevenson
2023-02-07 1:46 ` Laurent Pinchart
2023-02-03 19:18 ` [PATCH v2 10/13] media: i2c: imx290: Remove duplicated write to IMX290_CTRL_07 Dave Stevenson
2023-02-03 19:18 ` [PATCH v2 11/13] media: i2c: imx290: Add support for 74.25MHz external clock Dave Stevenson
2023-02-06 8:24 ` Alexander Stein
2023-02-07 1:50 ` Laurent Pinchart [this message]
2023-02-03 19:18 ` [PATCH v2 12/13] media: i2c: imx290: Add support for H & V Flips Dave Stevenson
2023-02-07 1:52 ` Laurent Pinchart
2023-02-03 19:18 ` [PATCH v2 13/13] media: i2c: imx290: Add the error code to logs in start_streaming Dave Stevenson
2023-02-06 8:27 ` Alexander Stein
2023-02-07 1:53 ` Laurent Pinchart
2023-02-07 1:55 ` [PATCH v2 00/13] imx290: Minor fixes, support for alternate INCK, and more ctrls Laurent Pinchart
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Y+GuSqapyqV+Lp9b@pendragon.ideasonboard.com \
--to=laurent.pinchart@ideasonboard.com \
--cc=alexander.stein@ew.tq-group.com \
--cc=dave.stevenson@raspberrypi.com \
--cc=linux-media@vger.kernel.org \
--cc=mani@kernel.org \
--cc=mchehab@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox