From: Petko Manolov <petko.manolov@konsulko.com>
To: Kieran Bingham <kieran.bingham@ideasonboard.com>
Cc: linux-media@vger.kernel.org, laurent.pinchart@ideasonboard.com,
sakari.ailus@iki.fi
Subject: Re: [PATCH v1 0/5] Adds media driver for Sony IMX492 sensor
Date: Mon, 28 Nov 2022 15:11:39 +0200 [thread overview]
Message-ID: <Y4Sziw2nt8gSyjSv@bender.k.g> (raw)
In-Reply-To: <166963953216.1079859.6469563044691422088@Monstersaurus>
On 22-11-28 12:45:32, Kieran Bingham wrote:
> Hi Petko,
>
> What device/ISP are you testing this sensor on?
I'll tell you, but only if you promise to not laugh too much. Deal?
i.MX8M-Mini
I hope nobody will notice the above line...
> Quoting Petko Manolov (2022-11-25 15:31:15)
> > This patch adds dt-bindings documentation, driver source, etc for Sony imx492
> > image sensor.
> >
> > imx492 is a diagonal 23.1 mm (Type 1.4) CMOS image sensor with color or
> > monochrome square pixel array and approximately 47.08 M effective pixels. 12-bit
> > digital output makes it possible to output the signals with high definition for
> > moving pictures. It is programmable through I2C interface. The I2C client
> > address can be either 0x10 or 0x1a depending on SLASEL pin. Image data is sent
> > through MIPI CSI-2.
> >
> > Petko Manolov (5):
> > DT bindings for imx492
> > media: i2c: imx492: driver's header
> > media: i2c: imx492: driver's source
> > media: i2c: add imx492 config entry
> > media: i2c: add imx492 entry for make
>
> Could you squash patches 2, 3, 4, and 5 into a single patch please?
This is the exact opposite to what the networking folks would prefer, but it's
OK with me.
> Also - I think you'll need an entry in MAINTAINERS.
Right, that one too.
> I can't see any reference to the selection controls:
> - V4L2_SEL_TGT_CROP_DEFAULT
> - V4L2_SEL_TGT_CROP
> - V4L2_SEL_TGT_CROP_BOUNDS
These are in a very early phase of implementing.
> Do you have the datasheet or sufficient information to be able to implement
> these controls?
Of course not. We are brute forcing our way forward by mostly reverse
engineering another solution that has an FPGA on the other end of the CSI link.
> --
> Kieran
>
> > .../bindings/media/i2c/sony,imx492.yaml | 101 ++
> > drivers/media/i2c/Kconfig | 14 +
> > drivers/media/i2c/Makefile | 1 +
> > drivers/media/i2c/imx492.c | 1092 +++++++++++++++++
> > drivers/media/i2c/imx492.h | 555 +++++++++
> > 5 files changed, 1763 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/i2c/sony,imx492.yaml
> > create mode 100644 drivers/media/i2c/imx492.c
> > create mode 100644 drivers/media/i2c/imx492.h
> >
> > --
> > 2.30.2
> >
Petko
next prev parent reply other threads:[~2022-11-28 13:12 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-11-25 15:31 [PATCH v1 0/5] Adds media driver for Sony IMX492 sensor Petko Manolov
2022-11-25 15:31 ` [PATCH v1 1/5] DT bindings for imx492 Petko Manolov
2022-11-28 4:37 ` Laurent Pinchart
2022-11-28 13:07 ` Petko Manolov
2022-11-28 13:28 ` Laurent Pinchart
2022-11-25 15:31 ` [PATCH v1 2/5] media: i2c: imx492: driver's header Petko Manolov
2022-11-28 4:40 ` Laurent Pinchart
2022-11-28 13:12 ` Petko Manolov
2022-11-28 12:47 ` Kieran Bingham
2022-11-28 13:14 ` Petko Manolov
2022-11-28 13:30 ` Laurent Pinchart
2022-11-28 13:53 ` Petko Manolov
2022-11-25 15:31 ` [PATCH v1 3/5] media: i2c: imx492: driver's source Petko Manolov
2022-11-28 5:16 ` Laurent Pinchart
2022-11-28 13:42 ` Petko Manolov
2022-11-28 14:08 ` Laurent Pinchart
2022-11-28 14:18 ` Dave Stevenson
2022-11-28 12:58 ` Kieran Bingham
2022-11-28 13:48 ` Petko Manolov
2022-11-25 15:31 ` [PATCH v1 4/5] media: i2c: add imx492 config entry Petko Manolov
2022-11-25 15:31 ` [PATCH v1 5/5] media: i2c: add imx492 entry for make Petko Manolov
2022-11-25 19:48 ` kernel test robot
2022-11-28 12:45 ` [PATCH v1 0/5] Adds media driver for Sony IMX492 sensor Kieran Bingham
2022-11-28 13:11 ` Petko Manolov [this message]
2022-11-28 13:38 ` Kieran Bingham
2022-11-28 13:46 ` Laurent Pinchart
2022-11-28 14:07 ` Petko Manolov
2022-11-28 15:04 ` Kieran Bingham
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Y4Sziw2nt8gSyjSv@bender.k.g \
--to=petko.manolov@konsulko.com \
--cc=kieran.bingham@ideasonboard.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-media@vger.kernel.org \
--cc=sakari.ailus@iki.fi \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox