From: Sakari Ailus <sakari.ailus@linux.intel.com>
To: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-media@vger.kernel.org,
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Subject: Re: [PATCH v2 2/2] media: i2c: IMX296 camera sensor driver
Date: Wed, 22 Dec 2021 00:41:08 +0200 [thread overview]
Message-ID: <YcJYBKB+Z4XYANgi@paasikivi.fi.intel.com> (raw)
In-Reply-To: <YcH5RufWI398s232@pendragon.ideasonboard.com>
Hi Laurent,
On Tue, Dec 21, 2021 at 05:56:54PM +0200, Laurent Pinchart wrote:
,,,
> > > +static int imx296_ctrls_init(struct imx296 *sensor)
> > > +{
> > > + struct v4l2_fwnode_device_properties props;
> > > + unsigned int hblank;
> > > + int ret;
> > > +
> > > + ret = v4l2_fwnode_device_parse(sensor->dev, &props);
> > > + if (ret < 0)
> > > + return ret;
> > > +
> > > + v4l2_ctrl_handler_init(&sensor->ctrls, 9);
> > > +
> > > + v4l2_ctrl_new_std(&sensor->ctrls, &imx296_ctrl_ops,
> > > + V4L2_CID_EXPOSURE, 1, 1048575, 1, 1104);
> > > + v4l2_ctrl_new_std(&sensor->ctrls, &imx296_ctrl_ops,
> > > + V4L2_CID_ANALOGUE_GAIN, IMX296_GAIN_MIN,
> > > + IMX296_GAIN_MAX, 1, IMX296_GAIN_MIN);
> > > +
> > > + /*
> > > + * Horizontal blanking is controlled through the HMAX register, which
> > > + * contains a line length in INCK clock units. The INCK frequency is
> > > + * fixed to 74.25 MHz. The HMAX value is currently fixed to 1100,
> >
> > It seems the driver supports other values, too. Shouldn't this be the
> > actual frequency?
>
> That's not clear to me from the documentation I have access to :-( It's
> quite convoluted, there are a few examples from which I tried to infer
> what was going on, but no clear explanation. My board uses a fixed clock
> frequency of 37.125MHz so I can't test other values.
>
> Can we start with this and update it later if we can figure out more
> (assuming there's an issue, it may actually be correct already) ?
Sounds reasonable. I was just wondering.
>
> > > + * convert it to a number of pixels based on the nominal pixel rate.
> > > + */
> > > + hblank = 1100 * 1188000000ULL / 10 / 74250000
> > > + - IMX296_PIXEL_ARRAY_WIDTH;
> > > + sensor->hblank = v4l2_ctrl_new_std(&sensor->ctrls, &imx296_ctrl_ops,
> > > + V4L2_CID_HBLANK, hblank, hblank, 1,
> > > + hblank);
> > > + if (sensor->hblank)
> > > + sensor->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> > > +
> > > + sensor->vblank = v4l2_ctrl_new_std(&sensor->ctrls, &imx296_ctrl_ops,
> > > + V4L2_CID_VBLANK, 30,
> > > + 1048575 - IMX296_PIXEL_ARRAY_HEIGHT,
> > > + 1, 30);
> > > + /*
> > > + * The sensor calculates the MIPI timings internally to achieve a bit
> > > + * rate between 1122 and 1198 Mbps. The exact value is unfortunately not
> > > + * reported, at least according to the documentation. Report a nominal
> > > + * rate of 1188 Mbps as that is used by the datasheet in multiple
> > > + * examples.
> > > + */
> > > + v4l2_ctrl_new_std(&sensor->ctrls, NULL, V4L2_CID_PIXEL_RATE,
> > > + 1122000000 / 10, 1198000000 / 10, 1, 1188000000 / 10);
> >
> > What about the link frequency?
> >
> > Is this value constant for the sensor? Or should there be a list of
> > hardware supported link frequencies?
>
> It seems to be constant, but again the documentation is fairly unclear.
Ack.
...
> > > +static int __maybe_unused imx296_runtime_resume(struct device *dev)
> > > +{
> > > + struct i2c_client *client = to_i2c_client(dev);
> > > + struct v4l2_subdev *subdev = i2c_get_clientdata(client);
> > > + struct imx296 *sensor = to_imx296(subdev);
> > > +
> > > + return imx296_power_on(sensor);
> > > +}
> > > +
> > > +static int __maybe_unused imx296_runtime_suspend(struct device *dev)
> > > +{
> > > + struct i2c_client *client = to_i2c_client(dev);
> > > + struct v4l2_subdev *subdev = i2c_get_clientdata(client);
> > > + struct imx296 *sensor = to_imx296(subdev);
> > > +
> > > + imx296_power_off(sensor);
> > > +
> > > + return 0;
> >
> > I'd merge these two with imx296_power_o{n,ff}.
>
> That would require calling imx296_runtime_resume() and
> imx296_runtime_suspend() in probe() and remove(), which I don't really
> like. I'd prefer keeping the functions separate.
You could keep calling the functions imx296_power_o{n,ff}. There's really
no need for two pairs of functions doing the same things.
...
> > > + dev_warn(&adapter->dev,
> > > + "I2C-Adapter doesn't support I2C_FUNC_SMBUS_BYTE\n");
> > > + return -EIO;
> > > + }
> > > +
> > > + sensor = devm_kzalloc(&client->dev, sizeof(*sensor), GFP_KERNEL);
> > > + if (!sensor)
> > > + return -ENOMEM;
> > > +
> > > + sensor->dev = &client->dev;
> > > +
> > > + mutex_init(&sensor->lock);
> >
> > You could simplify error handling a little by moving mutex init later. Up
> > to you.
>
> That's right, but if you don't mind I'd prefer keeping it here, to have
> ass the "static" initialization of "generic" members at the top.
Sure.
--
Regards,
Sakari Ailus
next prev parent reply other threads:[~2021-12-21 22:41 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-19 22:09 [PATCH v2 0/2] media: i2c: IMX296 camera sensor support Laurent Pinchart
2021-12-19 22:09 ` [PATCH v2 1/2] dt-bindings: media: i2c: Add IMX296 CMOS sensor binding Laurent Pinchart
2021-12-21 22:36 ` Sakari Ailus
2021-12-21 22:47 ` Laurent Pinchart
2021-12-22 17:36 ` Rob Herring
2021-12-19 22:09 ` [PATCH v2 2/2] media: i2c: IMX296 camera sensor driver Laurent Pinchart
2021-12-21 12:54 ` Sakari Ailus
2021-12-21 15:56 ` Laurent Pinchart
2021-12-21 22:41 ` Sakari Ailus [this message]
2021-12-21 22:53 ` Laurent Pinchart
2021-12-22 9:31 ` Sakari Ailus
2021-12-29 16:37 ` Laurent Pinchart
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YcJYBKB+Z4XYANgi@paasikivi.fi.intel.com \
--to=sakari.ailus@linux.intel.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-media@vger.kernel.org \
--cc=manivannan.sadhasivam@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox