[PATCH v8 0/7] media: i2c: IMX355 for the Pixel 3a

[PATCH v8 0/7] media: i2c: IMX355 for the Pixel 3a

[Richard Acayan]

This adds support for the IMX355 in devicetree and adds support for the
Pixel 3a front camera.

Changes since v7 (https://lore.kernel.org/r/20260117040657.27043-1-mailingradian@gmail.com):
- restrict data-lanes to 4 (4/7)
- include first patch (1/7)
- add back optional data-lanes in bindings (2/7)
- remove assert low on power on again (Bryan's review retained) (3/7)
- use dev_err_probe in power on (3/7)
- remove second error on probe power on (3/7)
- add review tags (2/7, 3/7, 7/7)

Changes since v6 (https://lore.kernel.org/r/20260107043044.92485-1-mailingradian@gmail.com):
- remove NAK from Krzysztof (3/6)
- assert reset GPIO on probe (3/6)
- change delays in reset sequence (3/6)
- remove __maybe_unused from OF match table (3/6)
- fix alignment for arguments to devm_regulator_bulk_get_const (3/6)
- remove front camera pin configuration (6/6)
- remove clock-lanes from camss endpoint (1/6, 6/6)
- remove data-lanes from camera sensor endpoint (2/6, 6/6)
- remove blank line at top of binding (2/6)
- add review tags (2/6, 3/6, 5/6, 6/6)

Changes since v5 (https://lore.kernel.org/r/20260107042451.92048-1-mailingradian@gmail.com):
- add Bryan to CC who added a Reviewed-by

Changes since v4 (https://lore.kernel.org/r/20251211014846.16602-1-mailingradian@gmail.com):
- add NAK from Krzysztof (2/5)
- label the camss ports (3/5, 5/5)
- define endpoint properties correctly (1/5)
- use devm_regulator_bulk_get_const (2/5)
- remove clock-names (1/5, 5/5)
- set reset GPIO as active low (1/5, 2/5, 5/5)
- explicitly drive reset low at start of sequence (2/5)
- make data-lanes in endpoint optional and start at 1 (1/5, 5/5)
- add mclk3 pin (4/5)
- add Reviewed-by's (4/5)

Changes since v3 (https://lore.kernel.org/r/20250905215516.289998-6-mailingradian@gmail.com):
- separate camera mclk pins and move to different patch (4/5, 5/5)
- remove polarity from rear camera pin (5/5)
- remove output-low from front camera pins (5/5)
- mention effects of dcf6fb89e6f7 ("media: qcom: camss: remove a check for unavailable CAMSS endpoint") (3/5)
- specify single clock-name without items nesting (1/5)
- rebase on 49c6ac166cf7 ("media: i2c: imx355: Replace client->dev
  usage") and eaa7d46d9654 ("media: i2c: imx335: Use V4L2 sensor clock
  helper") (2/5)
- do not use of_match_ptr for OF match table (2/5)
- remove redundant GPIO validity checks (2/5)
- describe endpoint data-lanes (1/5)

Changes since v2 (https://lore.kernel.org/r/20250714210227.714841-6-mailingradian@gmail.com):
- use devm_v4l2_sensor_clk_get (2/4)
- require supplies and clock-names (1/4)
- move unevaluatedProperties down (1/4)
- disable clocks as last power-off action (2/4)
- use 0 in gpio pin power-supply (4/4)

Changes since v1 (https://lore.kernel.org/r/20250630225944.320755-7-mailingradian@gmail.com):
- too much to have a complete list (1-4/4)
- squash camera orientation patch (4/4, previously 5/5)
- squash driver changes (2/4, previously 3/5)
- remove labelled endpoint node in sdm670.dtsi (3/4, 4/4)
- change init sequence to match other similar drivers (2/4)
- retrieve clock frequency from devicetree-defined clock (4/4)
- remove clock-frequency from dt-bindings (1/4)
- remove redundant descriptions of child nodes (1/4)
- switch initial drive of the reset GPIO to low (2/4)
- set mclk frequency to 19.2 MHz (4/4)
- add vdda-pll supply for camss (4/4)
- use common power on and off functions (2/4)
- use devm_clk_get_optional (2/4)
- remove extra layer when describing mclk pin (4/4)
- rename regulators (1/4, 2/4, 4/4)

Richard Acayan (7):
  dt-bindings: media: qcom,sdm670-camss: Remove clock-lanes property
  dt-bindings: media: i2c: Add Sony IMX355
  media: i2c: imx355: Support devicetree and power management
  media: i2c: imx355: Restrict data lanes to 4
  arm64: dts: qcom: sdm670: label the camss ports instead of endpoints
  arm64: dts: qcom: sdm670: add camera mclk pins
  arm64: dts: qcom: sdm670-google-sargo: add imx355 front camera

 .../bindings/media/i2c/sony,imx355.yaml       | 111 ++++++++++++++++
 .../bindings/media/qcom,sdm670-camss.yaml     |  13 --
 .../boot/dts/qcom/sdm670-google-sargo.dts     |  95 ++++++++++++++
 arch/arm64/boot/dts/qcom/sdm670.dtsi          |  46 ++++---
 drivers/media/i2c/imx355.c                    | 118 ++++++++++++++++--
 5 files changed, 347 insertions(+), 36 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml

-- 
2.53.0

[PATCH v8 1/7] dt-bindings: media: qcom,sdm670-camss: Remove clock-lanes property

[Richard Acayan]

The clock-lanes property has no effect on the hardware configuration, as
of 336136e197e2 ("media: dt-bindings: media: camss: Remove clock-lane
property"). Remove the clock-lanes property.

Suggested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/bbf0dcd9-d0f2-49a6-a2f2-6ec9376f2f59@linaro.org
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 .../bindings/media/qcom,sdm670-camss.yaml           | 13 -------------
 1 file changed, 13 deletions(-)

diff --git a/Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml
index 35c40fe22376..78b9e03da06b 100644
--- a/Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml
+++ b/Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml
@@ -116,15 +116,11 @@ properties:
             unevaluatedProperties: false
 
             properties:
-              clock-lanes:
-                maxItems: 1
-
               data-lanes:
                 minItems: 1
                 maxItems: 4
 
             required:
-              - clock-lanes
               - data-lanes
 
       port@1:
@@ -139,15 +135,11 @@ properties:
             unevaluatedProperties: false
 
             properties:
-              clock-lanes:
-                maxItems: 1
-
               data-lanes:
                 minItems: 1
                 maxItems: 4
 
             required:
-              - clock-lanes
               - data-lanes
 
       port@2:
@@ -162,15 +154,11 @@ properties:
             unevaluatedProperties: false
 
             properties:
-              clock-lanes:
-                maxItems: 1
-
               data-lanes:
                 minItems: 1
                 maxItems: 4
 
             required:
-              - clock-lanes
               - data-lanes
 
 required:
@@ -308,7 +296,6 @@ examples:
                     reg = <0>;
 
                     csiphy_ep0: endpoint {
-                        clock-lanes = <7>;
                         data-lanes = <0 1 2 3>;
                         remote-endpoint = <&front_sensor_ep>;
                     };
-- 
2.53.0

Re: [PATCH v8 1/7] dt-bindings: media: qcom,sdm670-camss: Remove clock-lanes property

[Krzysztof Kozlowski]

On Mon, Feb 09, 2026 at 09:02:00PM -0500, Richard Acayan wrote:
> The clock-lanes property has no effect on the hardware configuration, as
> of 336136e197e2 ("media: dt-bindings: media: camss: Remove clock-lane

Please run checkpatch.

> property"). Remove the clock-lanes property.
> 
> Suggested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
> Link: https://lore.kernel.org/r/bbf0dcd9-d0f2-49a6-a2f2-6ec9376f2f59@linaro.org
> Signed-off-by: Richard Acayan <mailingradian@gmail.com>

Best regards,
Krzysztof

Re: [PATCH v8 1/7] dt-bindings: media: qcom,sdm670-camss: Remove clock-lanes property

[Vladimir Zapolskiy]

On 2/10/26 04:02, Richard Acayan wrote:
> The clock-lanes property has no effect on the hardware configuration, as
> of 336136e197e2 ("media: dt-bindings: media: camss: Remove clock-lane
> property"). Remove the clock-lanes property.
> 
> Suggested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>

Remove this unauthrized tag from me.

I asked to remove CAMSS 'clock-lanes' property from .dtsi file, and this
displayed change very is different one.

> Link: https://lore.kernel.org/r/bbf0dcd9-d0f2-49a6-a2f2-6ec9376f2f59@linaro.org

Remove this given irrelevant link also.

> Signed-off-by: Richard Acayan <mailingradian@gmail.com>

-- 
Best wishes,
Vladimir

Re: [PATCH v8 1/7] dt-bindings: media: qcom,sdm670-camss: Remove clock-lanes property

[Bryan O'Donoghue]

On 10/02/2026 02:02, Richard Acayan wrote:
> The clock-lanes property has no effect on the hardware configuration, as
> of 336136e197e2 ("media: dt-bindings: media: camss: Remove clock-lane
> property"). Remove the clock-lanes property.
> 
> Suggested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
> Link: https://lore.kernel.org/r/bbf0dcd9-d0f2-49a6-a2f2-6ec9376f2f59@linaro.org
> Signed-off-by: Richard Acayan <mailingradian@gmail.com>
> ---
>   .../bindings/media/qcom,sdm670-camss.yaml           | 13 -------------
>   1 file changed, 13 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml
> index 35c40fe22376..78b9e03da06b 100644
> --- a/Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml
> +++ b/Documentation/devicetree/bindings/media/qcom,sdm670-camss.yaml
> @@ -116,15 +116,11 @@ properties:
>               unevaluatedProperties: false
>   
>               properties:
> -              clock-lanes:
> -                maxItems: 1
> -
>                 data-lanes:
>                   minItems: 1
>                   maxItems: 4
>   
>               required:
> -              - clock-lanes
>                 - data-lanes
>   
>         port@1:
> @@ -139,15 +135,11 @@ properties:
>               unevaluatedProperties: false
>   
>               properties:
> -              clock-lanes:
> -                maxItems: 1
> -
>                 data-lanes:
>                   minItems: 1
>                   maxItems: 4
>   
>               required:
> -              - clock-lanes
>                 - data-lanes
>   
>         port@2:
> @@ -162,15 +154,11 @@ properties:
>               unevaluatedProperties: false
>   
>               properties:
> -              clock-lanes:
> -                maxItems: 1
> -
>                 data-lanes:
>                   minItems: 1
>                   maxItems: 4
>   
>               required:
> -              - clock-lanes
>                 - data-lanes
>   
>   required:
> @@ -308,7 +296,6 @@ examples:
>                       reg = <0>;
>   
>                       csiphy_ep0: endpoint {
> -                        clock-lanes = <7>;
>                           data-lanes = <0 1 2 3>;
>                           remote-endpoint = <&front_sensor_ep>;
>                       };

I think the ask was to have clock-lanes in the board dts rather than 
dropping the clock-lanes from the yaml.

We want to keep clock-lanes in general as some SoCs support changing the 
lane assignment.

---
bod

[PATCH v8 2/7] dt-bindings: media: i2c: Add Sony IMX355

[Richard Acayan]

The IMX355 camera sensor is a camera sensor that can be found as the
front camera in some smartphones, such as the Pixel 3, Pixel 3 XL, Pixel
3a, and Pixel 3a XL. It already has a driver, but needs support for
device tree. Document the IMX355 to support defining it in device tree.

Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 .../bindings/media/i2c/sony,imx355.yaml       | 111 ++++++++++++++++++
 1 file changed, 111 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml

diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml
new file mode 100644
index 000000000000..6050d7e7dcfe
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/sony,imx355.yaml
@@ -0,0 +1,111 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/sony,imx355.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony IMX355 Sensor
+
+maintainers:
+  - Richard Acayan <mailingradian@gmail.com>
+
+description:
+  The IMX355 sensor is a 3280x2464 image sensor, commonly found as the front
+  camera in smartphones.
+
+allOf:
+  - $ref: /schemas/media/video-interface-devices.yaml#
+
+properties:
+  compatible:
+    const: sony,imx355
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  avdd-supply:
+    description: Analog power supply.
+
+  dvdd-supply:
+    description: Digital power supply.
+
+  dovdd-supply:
+    description: Interface power supply.
+
+  reset-gpios:
+    description: Reset GPIO (active low).
+    maxItems: 1
+
+  port:
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    additionalProperties: false
+
+    properties:
+      endpoint:
+        $ref: /schemas/media/video-interfaces.yaml
+        unevaluatedProperties: false
+
+        properties:
+          data-lanes:
+            minItems: 4
+            maxItems: 4
+
+        required:
+          - link-frequencies
+
+    required:
+      - endpoint
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - avdd-supply
+  - dvdd-supply
+  - dovdd-supply
+  - port
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,camcc-sdm845.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        camera@1a {
+            compatible = "sony,imx355";
+            reg = <0x1a>;
+
+            clocks = <&camcc CAM_CC_MCLK2_CLK>;
+
+            assigned-clocks = <&camcc CAM_CC_MCLK2_CLK>;
+            assigned-clock-rates = <24000000>;
+
+            reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
+
+            avdd-supply = <&cam_front_ldo>;
+            dvdd-supply = <&cam_front_ldo>;
+            dovdd-supply = <&cam_vio_ldo>;
+
+            pinctrl-names = "default";
+            pinctrl-0 = <&cam_front_default>;
+
+            rotation = <270>;
+            orientation = <0>;
+
+            port {
+                cam_front_endpoint: endpoint {
+                    data-lanes = <1 2 3 4>;
+                    link-frequencies = /bits/ 64 <360000000>;
+                    remote-endpoint = <&camss_endpoint1>;
+                };
+            };
+        };
+    };
-- 
2.53.0

[PATCH v8 3/7] media: i2c: imx355: Support devicetree and power management

[Richard Acayan]

A device tree compatible makes it possible for this driver to be used on
Open Firmware devices. Initialization of power-managed resources such as
the reset GPIO and voltage regulators can be specified in the device
tree and handled by the driver. Add support for this so the Pixel 3a can
use the driver.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 drivers/media/i2c/imx355.c | 111 ++++++++++++++++++++++++++++++++++---
 1 file changed, 103 insertions(+), 8 deletions(-)

diff --git a/drivers/media/i2c/imx355.c b/drivers/media/i2c/imx355.c
index 776107efe386..9ca87488c933 100644
--- a/drivers/media/i2c/imx355.c
+++ b/drivers/media/i2c/imx355.c
@@ -3,9 +3,13 @@
 
 #include <linux/acpi.h>
 #include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
 #include <linux/unaligned.h>
 
 #include <media/v4l2-ctrls.h>
@@ -125,6 +129,15 @@ struct imx355 {
 	 * Protect access to sensor v4l2 controls.
 	 */
 	struct mutex mutex;
+
+	struct gpio_desc *reset_gpio;
+	struct regulator_bulk_data *supplies;
+};
+
+static const struct regulator_bulk_data imx355_supplies[] = {
+	{ .supply = "avdd" },
+	{ .supply = "dvdd" },
+	{ .supply = "dovdd" },
 };
 
 static const struct imx355_reg imx355_global_regs[] = {
@@ -1515,6 +1528,52 @@ static const struct v4l2_subdev_internal_ops imx355_internal_ops = {
 	.open = imx355_open,
 };
 
+static int imx355_power_off(struct device *dev)
+{
+	struct i2c_client *client = container_of(dev, struct i2c_client, dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct imx355 *imx355 = to_imx355(sd);
+
+	gpiod_set_value_cansleep(imx355->reset_gpio, 1);
+
+	regulator_bulk_disable(ARRAY_SIZE(imx355_supplies), imx355->supplies);
+	clk_disable_unprepare(imx355->clk);
+
+	return 0;
+}
+
+static int imx355_power_on(struct device *dev)
+{
+	struct i2c_client *client = container_of(dev, struct i2c_client, dev);
+	struct v4l2_subdev *sd = i2c_get_clientdata(client);
+	struct imx355 *imx355 = to_imx355(sd);
+	int ret;
+
+	ret = clk_prepare_enable(imx355->clk);
+	if (ret)
+		return dev_err_probe(dev, ret, "failed to enable clocks");
+
+	ret = regulator_bulk_enable(ARRAY_SIZE(imx355_supplies),
+				    imx355->supplies);
+	if (ret) {
+		dev_err_probe(dev, ret, "failed to enable regulators");
+		goto error_disable_clocks;
+	}
+
+	usleep_range(1000, 2000);
+	gpiod_set_value_cansleep(imx355->reset_gpio, 0);
+	usleep_range(10000, 11000);
+
+	return 0;
+
+error_disable_clocks:
+	clk_disable_unprepare(imx355->clk);
+	return ret;
+}
+
+static DEFINE_RUNTIME_DEV_PM_OPS(imx355_pm_ops, imx355_power_off,
+				 imx355_power_on, NULL);
+
 /* Initialize control handlers */
 static int imx355_init_controls(struct imx355 *imx355)
 {
@@ -1689,16 +1748,26 @@ static int imx355_probe(struct i2c_client *client)
 				     "external clock %lu is not supported\n",
 				     freq);
 
-	/* Initialize subdev */
-	v4l2_i2c_subdev_init(&imx355->sd, client, &imx355_subdev_ops);
-
-	/* Check module identity */
-	ret = imx355_identify_module(imx355);
+	ret = devm_regulator_bulk_get_const(imx355->dev,
+					    ARRAY_SIZE(imx355_supplies),
+					    imx355_supplies,
+					    &imx355->supplies);
 	if (ret) {
-		dev_err(imx355->dev, "failed to find sensor: %d", ret);
+		dev_err_probe(imx355->dev, ret, "could not get regulators");
 		goto error_probe;
 	}
 
+	imx355->reset_gpio = devm_gpiod_get_optional(imx355->dev, "reset",
+						     GPIOD_OUT_HIGH);
+	if (IS_ERR(imx355->reset_gpio)) {
+		ret = dev_err_probe(imx355->dev, PTR_ERR(imx355->reset_gpio),
+				    "failed to get gpios");
+		goto error_probe;
+	}
+
+	/* Initialize subdev */
+	v4l2_i2c_subdev_init(&imx355->sd, client, &imx355_subdev_ops);
+
 	imx355->hwcfg = imx355_get_hwcfg(imx355->dev);
 	if (!imx355->hwcfg) {
 		dev_err(imx355->dev, "failed to get hwcfg");
@@ -1706,13 +1775,24 @@ static int imx355_probe(struct i2c_client *client)
 		goto error_probe;
 	}
 
+	ret = imx355_power_on(imx355->dev);
+	if (ret)
+		goto error_probe;
+
+	/* Check module identity */
+	ret = imx355_identify_module(imx355);
+	if (ret) {
+		dev_err(imx355->dev, "failed to find sensor: %d", ret);
+		goto error_power_off;
+	}
+
 	/* Set default mode to max resolution */
 	imx355->cur_mode = &supported_modes[0];
 
 	ret = imx355_init_controls(imx355);
 	if (ret) {
 		dev_err(imx355->dev, "failed to init controls: %d", ret);
-		goto error_probe;
+		goto error_power_off;
 	}
 
 	/* Initialize subdev */
@@ -1752,6 +1832,9 @@ static int imx355_probe(struct i2c_client *client)
 error_handler_free:
 	v4l2_ctrl_handler_free(imx355->sd.ctrl_handler);
 
+error_power_off:
+	imx355_power_off(imx355->dev);
+
 error_probe:
 	mutex_destroy(&imx355->mutex);
 
@@ -1768,7 +1851,11 @@ static void imx355_remove(struct i2c_client *client)
 	v4l2_ctrl_handler_free(sd->ctrl_handler);
 
 	pm_runtime_disable(imx355->dev);
-	pm_runtime_set_suspended(imx355->dev);
+
+	if (!pm_runtime_status_suspended(imx355->dev)) {
+		imx355_power_off(imx355->dev);
+		pm_runtime_set_suspended(imx355->dev);
+	}
 
 	mutex_destroy(&imx355->mutex);
 }
@@ -1779,10 +1866,18 @@ static const struct acpi_device_id imx355_acpi_ids[] __maybe_unused = {
 };
 MODULE_DEVICE_TABLE(acpi, imx355_acpi_ids);
 
+static const struct of_device_id imx355_match_table[] = {
+	{ .compatible = "sony,imx355", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx355_match_table);
+
 static struct i2c_driver imx355_i2c_driver = {
 	.driver = {
 		.name = "imx355",
 		.acpi_match_table = ACPI_PTR(imx355_acpi_ids),
+		.of_match_table = imx355_match_table,
+		.pm = &imx355_pm_ops,
 	},
 	.probe = imx355_probe,
 	.remove = imx355_remove,
-- 
2.53.0

[PATCH v8 5/7] arm64: dts: qcom: sdm670: label the camss ports instead of endpoints

[Richard Acayan]

Endpoints cannot be pre-defined since dcf6fb89e6f7 ("media: qcom: camss:
remove a check for unavailable CAMSS endpoint") was applied, probing all
endpoint nodes and requiring them to have a remote. There is no sensible
remote in the SoC devicetree because camera sensors are board-specific.

The ports are meant to be extended by a board devicetree in order to
define fully configured endpoints and connect the ports to camera
sensors. For nodes that are only meaningful if extended, labels are
usually assigned. Label these ports so they can be extended directly.

Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 arch/arm64/boot/dts/qcom/sdm670.dtsi | 18 +++---------------
 1 file changed, 3 insertions(+), 15 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sdm670.dtsi b/arch/arm64/boot/dts/qcom/sdm670.dtsi
index b8a8dcbdfbe3..3eb4eaf7b8d7 100644
--- a/arch/arm64/boot/dts/qcom/sdm670.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm670.dtsi
@@ -1776,28 +1776,16 @@ ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				camss_port0: port@0 {
 					reg = <0>;
-
-					camss_endpoint0: endpoint {
-						status = "disabled";
-					};
 				};
 
-				port@1 {
+				camss_port1: port@1 {
 					reg = <1>;
-
-					camss_endpoint1: endpoint {
-						status = "disabled";
-					};
 				};
 
-				port@2 {
+				camss_port2: port@2 {
 					reg = <2>;
-
-					camss_endpoint2: endpoint {
-						status = "disabled";
-					};
 				};
 			};
 		};
-- 
2.53.0

[PATCH v8 6/7] arm64: dts: qcom: sdm670: add camera mclk pins

[Richard Acayan]

The camera subsystem is added for the SoC common devicetree, but the
mclk pins should also be common across the SoC. Add the mclk pins for
the cameras.

Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/5135823c-f2e4-4873-9e3a-9d190cac0113@oss.qualcomm.com
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bod@kernel.org>
Reviewed-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 arch/arm64/boot/dts/qcom/sdm670.dtsi | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm670.dtsi b/arch/arm64/boot/dts/qcom/sdm670.dtsi
index 3eb4eaf7b8d7..f21e60a6a2ef 100644
--- a/arch/arm64/boot/dts/qcom/sdm670.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm670.dtsi
@@ -1196,6 +1196,34 @@ tlmm: pinctrl@3400000 {
 			gpio-ranges = <&tlmm 0 0 151>;
 			wakeup-parent = <&pdc>;
 
+			cam_mclk0_default: cam-mclk0-default-state {
+				pins = "gpio13";
+				function = "cam_mclk";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			cam_mclk1_default: cam-mclk1-default-state {
+				pins = "gpio14";
+				function = "cam_mclk";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			cam_mclk2_default: cam-mclk2-default-state {
+				pins = "gpio15";
+				function = "cam_mclk";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			cam_mclk3_default: cam-mclk3-default-state {
+				pins = "gpio16";
+				function = "cam_mclk";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
 			cci0_default: cci0-default-state {
 				pins = "gpio17", "gpio18";
 				function = "cci_i2c";
-- 
2.53.0

[PATCH v8 7/7] arm64: dts: qcom: sdm670-google-sargo: add imx355 front camera

[Richard Acayan]

The Sony IMX355 is the front camera on the Pixel 3a, mounted in portrait
mode. It is connected to CSIPHY1 and CCI I2C1, and uses MCLK2. Add
support for it.

Co-developed-by: Robert Mader <robert.mader@collabora.com>
Signed-off-by: Robert Mader <robert.mader@collabora.com>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 .../boot/dts/qcom/sdm670-google-sargo.dts     | 95 +++++++++++++++++++
 1 file changed, 95 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts b/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
index ed55646ca419..e925cba0381f 100644
--- a/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
+++ b/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
@@ -172,6 +172,34 @@ vreg_s2b_1p05: vreg-s2b-regulator {
 		regulator-min-microvolt = <1050000>;
 		regulator-max-microvolt = <1050000>;
 	};
+
+	cam_front_ldo: cam-front-ldo-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_front_ldo";
+		regulator-min-microvolt = <1352000>;
+		regulator-max-microvolt = <1352000>;
+		regulator-enable-ramp-delay = <135>;
+
+		gpios = <&pm660l_gpios 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&cam_front_ldo_pin>;
+		pinctrl-names = "default";
+	};
+
+	cam_vio_ldo: cam-vio-ldo-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_vio_ldo";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-enable-ramp-delay = <233>;
+
+		gpios = <&pm660_gpios 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&cam_vio_pin>;
+		pinctrl-names = "default";
+	};
 };
 
 &apps_rsc {
@@ -392,6 +420,59 @@ vreg_bob: bob {
 	};
 };
 
+&camss {
+	vdda-phy-supply = <&vreg_l1a_1p225>;
+	vdda-pll-supply = <&vreg_s6a_0p87>;
+
+	status = "okay";
+};
+
+&camss_port1 {
+	camss_endpoint1: endpoint {
+		data-lanes = <0 1 2 3>;
+		remote-endpoint = <&cam_front_endpoint>;
+	};
+};
+
+&cci {
+	pinctrl-0 = <&cci1_default>;
+	pinctrl-1 = <&cci1_sleep>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+};
+
+&cci_i2c1 {
+	camera@1a {
+		compatible = "sony,imx355";
+		reg = <0x1a>;
+
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+
+		assigned-clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		assigned-clock-rates = <19200000>;
+
+		reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
+
+		avdd-supply = <&cam_front_ldo>;
+		dvdd-supply = <&cam_front_ldo>;
+		dovdd-supply = <&cam_vio_ldo>;
+
+		pinctrl-0 = <&cam_mclk2_default>;
+		pinctrl-names = "default";
+
+		rotation = <270>;
+		orientation = <0>;
+
+		port {
+			cam_front_endpoint: endpoint {
+				link-frequencies = /bits/ 64 <360000000>;
+				remote-endpoint = <&camss_endpoint1>;
+			};
+		};
+	};
+};
+
 &gcc {
 	protected-clocks = <GCC_QSPI_CORE_CLK>,
 			   <GCC_QSPI_CORE_CLK_SRC>,
@@ -490,6 +571,14 @@ &pm660_charger {
 	status = "okay";
 };
 
+&pm660_gpios {
+	cam_vio_pin: cam-vio-state {
+		pins = "gpio13";
+		function = "normal";
+		power-source = <0>;
+	};
+};
+
 &pm660_rradc {
 	status = "okay";
 };
@@ -508,6 +597,12 @@ led-0 {
 };
 
 &pm660l_gpios {
+	cam_front_ldo_pin: cam-front-state {
+		pins = "gpio4";
+		function = "normal";
+		power-source = <0>;
+	};
+
 	vol_up_pin: vol-up-state {
 		pins = "gpio7";
 		function = "normal";
-- 
2.53.0

Re: [PATCH v8 0/7] media: i2c: IMX355 for the Pixel 3a

[Richard Acayan]

On Mon, Feb 09, 2026 at 09:01:59PM -0500, Richard Acayan wrote:
> This adds support for the IMX355 in devicetree and adds support for the
> Pixel 3a front camera.
> 
> Changes since v7 (https://lore.kernel.org/r/20260117040657.27043-1-mailingradian@gmail.com):
> - restrict data-lanes to 4 (4/7)

Apparently the 4th patch has been blocked by Gmail.

Re: [PATCH v8 0/7] media: i2c: IMX355 for the Pixel 3a

[Vladimir Zapolskiy]

On 2/11/26 02:21, Richard Acayan wrote:
> On Mon, Feb 09, 2026 at 09:01:59PM -0500, Richard Acayan wrote:
>> This adds support for the IMX355 in devicetree and adds support for the
>> Pixel 3a front camera.
>>
>> Changes since v7 (https://lore.kernel.org/r/20260117040657.27043-1-mailingradian@gmail.com):
>> - restrict data-lanes to 4 (4/7)
> 
> Apparently the 4th patch has been blocked by Gmail.

To complete the series you can send it by

   git send-email --in-reply-to="<20260210020207.10246-1-mailingradian@gmail.com>" <snip> v8-0004-*

-- 
Best wishes,
Vladimir