From mboxrd@z Thu Jan 1 00:00:00 1970 From: Jorge Ramirez-Ortiz Subject: [PATCH v3 1/2] mtd: mediatek: device tree docs for MTK Smart Device Gen1 NAND Date: Mon, 11 Apr 2016 12:56:11 -0400 Message-ID: <1460393772-26910-2-git-send-email-jorge.ramirez-ortiz@linaro.org> References: <1460393772-26910-1-git-send-email-jorge.ramirez-ortiz@linaro.org> Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Return-path: In-Reply-To: <1460393772-26910-1-git-send-email-jorge.ramirez-ortiz-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org> List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Sender: "Linux-mediatek" Errors-To: linux-mediatek-bounces+glpam-linux-mediatek=m.gmane.org-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org To: jorge.ramirez-ortiz-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org, dwmw2-wEGCiKHe2LqWVfeAwA7xHQ@public.gmane.org, boris.brezillon-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org, computersforpeace-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, matthias.bgg-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: linux-mediatek-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, xiaolei.li-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org, linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, daniel.thompson-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org, erin.lo-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org List-Id: linux-mediatek@lists.infradead.org This patch adds documentation support for Smart Device Gen1 type of NAND controllers. Signed-off-by: Jorge Ramirez-Ortiz --- Documentation/devicetree/bindings/mtd/mtk-nand.txt | 145 +++++++++++++++++++++ 1 file changed, 145 insertions(+) create mode 100644 Documentation/devicetree/bindings/mtd/mtk-nand.txt diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt new file mode 100644 index 0000000..ca3cc95 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt @@ -0,0 +1,145 @@ +MTK SoCs NAND FLASH controller (NFC) DT binding + +This file documents the device tree bindings for MTK SoCs NAND controllers. +The functional split of the controller requires two drivers to operate: +the nand controller interface driver and the ECC engine driver. + +The hardware description for both devices must be captured as device +tree nodes. + +1) NFC NAND Controller Interface (NFI): +======================================= + +The first part of NFC is NAND Controller Interface (NFI) HW. +Required NFI properties: +- compatible: Should be "mediatek,mtxxxx-nfc". +- reg: Base physical address and size of NFI. +- interrupts: Interrupts of NFI. +- clocks: NFI required clocks. +- clock-names: NFI clocks internal name. +- status: Disabled default. Then set "okay" by platform. +- ecc-engine: Required ECC Engine node. +- #address-cells: NAND chip index, should be 1. +- #size-cells: Should be 0. + +Example: + + nandc: nfi@1100d000 { + compatible = "mediatek,mt2701-nfc"; + reg = <0 0x1100d000 0 0x1000>; + interrupts = ; + clocks = <&pericfg CLK_PERI_NFI>, + <&pericfg CLK_PERI_NFI_PAD>; + clock-names = "nfi_clk", "pad_clk"; + status = "disabled"; + ecc-engine = <&bch>; + #address-cells = <1>; + #size-cells = <0>; + }; + +Platform related properties, should be set in {platform_name}.dts: +- children nodes: NAND chips. + +Children nodes properties: +- reg: Chip Select Signal, default 0. + Set as reg = <0>, <1> when need 2 CS. +- spare_per_sector: Spare size of each sector. +- nand-on-flash-bbt: Store BBT on NAND Flash. +- nand-ecc-mode: NAND ecc mode (check driver for supported modes) +- nand-ecc-strength: Number of bits to correct per ECC step. +- nand-ecc-step-size: Number of data bytes covered by a single ECC step. + +Optional: +- vmch-supply: NAND power supply. +- pinctrl-names: Default NAND pin GPIO setting name. +- pinctrl-0: GPIO setting node. + +Example: + &pio { + nand_pins_default: nanddefault { + pins_dat { + pinmux = , + , + , + , + , + , + , + , + ; + input-enable; + drive-strength = ; + bias-pull-up; + }; + + pins_we { + pinmux = ; + drive-strength = ; + bias-pull-up = ; + }; + + pins_ale { + pinmux = ; + drive-strength = ; + bias-pull-down = ; + }; + }; + }; + + &nandc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins_default>; + nand@0 { + reg = <0>; + spare_per_sector = <56>; + nand-on-flash-bbt; + nand-ecc-mode = "hw"; + nand-ecc-strength = <24>; + nand-ecc-step-size = <1024>; + }; + }; + +NAND chip optional subnodes: +- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + preloader@0 { + label = "pl"; + read-only; + reg = <0x00000000 0x00400000>; + }; + android@0x00400000 { + label = "android"; + reg = <0x00400000 0x12c00000>; + }; + }; + }; + +2) ECC Engine: +============== + +Required BCH properties: +- compatible: Should be "mediatek,mtxxxx-ecc". +- reg: Base physical address and size of ECC. +- interrupts: Interrupts of ECC. +- clocks: ECC required clocks. +- clock-names: ECC clocks internal name. +- status: Disabled default. Then set "okay" by platform. + +Example: + + bch: ecc@1100e000 { + compatible = "mediatek,mt2701-ecc"; + reg = <0 0x1100e000 0 0x1000>; + interrupts = ; + clocks = <&pericfg CLK_PERI_NFI_ECC>; + clock-names = "nfiecc_clk"; + status = "disabled"; + }; -- 2.5.0