[PATCH v1 2/2] Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices

sean.wang
2019-03-08T01:15:44Z

From: Sean Wang <sean.wang@mediatek.com>

This adds the support of enabling MT7663S and MT7668S SDIO-based
Bluetooth function.

There are quite many differences between MT766[3,8]S and standard
Bluetooth SDIO devices such as Type-A and Type-B devices. For example,
MT766[3,8]S have its own SDIO registers layout, definition, SDIO packet
format, and the specific flow should be programmed on them to complete
the device initialization and low power control and so on.

Currently, there are many independent programming sequences from the
transport which are exactly the same as the ones in btusb.c about MediaTek
support [1] and btmtkuart.c. We can try to split the transport independent
Bluetooth setups on the advance, place them into the common files and allow
varous transport drivers to reuse them in the future.

[1] http://lists.infradead.org/pipermail/linux-mediatek/2019-January/017074.html

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
---
drivers/bluetooth/Kconfig | 11 +
drivers/bluetooth/Makefile | 1 +
drivers/bluetooth/btmtksdio.c | 979 ++++++++++++++++++++++++++++++++++
3 files changed, 991 insertions(+)
create mode 100644 drivers/bluetooth/btmtksdio.c

diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
index de62ccf43df6..bff51d45cdcf 100644
--- a/drivers/bluetooth/Kconfig
+++ b/drivers/bluetooth/Kconfig
@@ -390,6 +390,17 @@ config BT_WILINK
Say Y here to compile support for Texas Instrument's WiLink7 driver
into the kernel or say M to compile it as module (btwilink).

+config BT_MTKSDIO
+ tristate "MediaTek HCI SDIO driver"
+ depends on MMC
+ help
+ MediaTek Bluetooth HCI SDIO driver.
+ This driver is required if you want to use MediaTek Bluetooth
+ with SDIO interface.
+
+ Say Y here to compile support for MediaTek Bluetooth SDIO devices
+ into the kernel or say M to compile it as module (btmtksdio).
+
config BT_MTKUART
tristate "MediaTek HCI UART driver"
depends on SERIAL_DEV_BUS
diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
index b7e393cfc1e3..34887b9b3a85 100644
--- a/drivers/bluetooth/Makefile
+++ b/drivers/bluetooth/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_BT_ATH3K) += ath3k.o
obj-$(CONFIG_BT_MRVL) += btmrvl.o
obj-$(CONFIG_BT_MRVL_SDIO) += btmrvl_sdio.o
obj-$(CONFIG_BT_WILINK) += btwilink.o
+obj-$(CONFIG_BT_MTKSDIO) += btmtksdio.o
obj-$(CONFIG_BT_MTKUART) += btmtkuart.o
obj-$(CONFIG_BT_QCOMSMD) += btqcomsmd.o
obj-$(CONFIG_BT_BCM) += btbcm.o
diff --git a/drivers/bluetooth/btmtksdio.c b/drivers/bluetooth/btmtksdio.c
new file mode 100644
index 000000000000..b4b8320f279e
--- /dev/null
+++ b/drivers/bluetooth/btmtksdio.c
@@ -0,0 +1,979 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019 MediaTek Inc.
+
+/*
+ * Bluetooth support for MediaTek SDIO devices
+ *
+ * This file is written based on btsdio.c and btmtkuart.c.
+ *
+ * Author: Sean Wang <sean.wang@mediatek.com>
+ *
+ */
+
+#include <asm/unaligned.h>
+#include <linux/atomic.h>
+#include <linux/firmware.h>
+#include <linux/init.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/skbuff.h>
+
+#include <linux/mmc/host.h>
+#include <linux/mmc/sdio_ids.h>
+#include <linux/mmc/sdio_func.h>
+
+#include <net/bluetooth/bluetooth.h>
+#include <net/bluetooth/hci_core.h>
+
+#include "h4_recv.h"
+
+#define VERSION "0.1"
+
+#define FIRMWARE_MT7663 "mediatek/mt7663pr2h.bin"
+#define FIRMWARE_MT7668 "mediatek/mt7668pr2h.bin"
+
+struct btmtksdio_data {
+ const char *fwname;
+};
+
+static const struct btmtksdio_data mt7663_data = {
+ .fwname = FIRMWARE_MT7663,
+};
+
+static const struct btmtksdio_data mt7668_data = {
+ .fwname = FIRMWARE_MT7668,
+};
+
+static const struct sdio_device_id btmtksdio_table[] = {
+ {SDIO_DEVICE(SDIO_VENDOR_ID_MEDIATEK, 0x7663),
+ .driver_data = (kernel_ulong_t)&mt7663_data },
+ {SDIO_DEVICE(SDIO_VENDOR_ID_MEDIATEK, 0x7668),
+ .driver_data = (kernel_ulong_t)&mt7668_data },
+ { } /* Terminating entry */
+};
+
+#define MTK_REG_CHLPCR 0x4 /* W1S */
+#define C_INT_EN_SET BIT(0)
+#define C_INT_EN_CLR BIT(1)
+#define C_FW_OWN_REQ_SET BIT(8)
+#define C_FW_OWN_REQ_CLR BIT(9)
+
+#define MTK_REG_CSDIOCSR 0x8
+#define SDIO_RE_INIT_EN BIT(0)
+#define SDIO_INT_CTL BIT(2)
+
+#define MTK_REG_CHCR 0xc
+#define C_INT_CLR_CTRL BIT(1)
+
+/* CHISR have the same bits field definition with CHIER */
+#define MTK_REG_CHISR 0x10
+#define MTK_REG_CHIER 0x14
+#define FW_OWN_BACK_INT BIT(0)
+#define RX_DONE_INT BIT(1)
+#define TX_EMPTY BIT(2)
+#define TX_FIFO_OVERFLOW BIT(8)
+#define RX_PKT_LEN GENMASK(31, 16)
+
+#define MTK_REG_CTDR 0x18
+
+#define MTK_REG_CRDR 0x1c
+
+#define MTK_SDIO_BLOCK_SIZE 256
+
+#define BTMTKSDIO_TX_WAIT_VND_EVT 1
+
+enum {
+ MTK_WMT_PATCH_DWNLD = 0x1,
+ MTK_WMT_TEST = 0x2,
+ MTK_WMT_WAKEUP = 0x3,
+ MTK_WMT_HIF = 0x4,
+ MTK_WMT_FUNC_CTRL = 0x6,
+ MTK_WMT_RST = 0x7,
+ MTK_WMT_SEMAPHORE = 0x17,
+};
+
+enum {
+ BTMTK_WMT_INVALID,
+ BTMTK_WMT_PATCH_UNDONE,
+ BTMTK_WMT_PATCH_DONE,
+ BTMTK_WMT_ON_UNDONE,
+ BTMTK_WMT_ON_DONE,
+ BTMTK_WMT_ON_PROGRESS,
+};
+
+struct mtkbtsdio_hdr {
+ __le16 len;
+ __le16 reserved;
+ u8 bt_type;
+} __packed;
+
+struct mtk_wmt_hdr {
+ u8 dir;
+ u8 op;
+ __le16 dlen;
+ u8 flag;
+} __packed;
+
+struct mtk_hci_wmt_cmd {
+ struct mtk_wmt_hdr hdr;
+ u8 data[256];
+} __packed;
+
+struct btmtk_hci_wmt_evt {
+ struct hci_event_hdr hhdr;
+ struct mtk_wmt_hdr whdr;
+} __packed;
+
+struct btmtk_hci_wmt_evt_funcc {
+ struct btmtk_hci_wmt_evt hwhdr;
+ __be16 status;
+} __packed;
+
+struct btmtk_tci_sleep {
+ u8 mode;
+ __le16 duration;
+ __le16 host_duration;
+ u8 host_wakeup_pin;
+ u8 time_compensation;
+} __packed;
+
+struct btmtk_hci_wmt_params {
+ u8 op;
+ u8 flag;
+ u16 dlen;
+ const void *data;
+ u32 *status;
+};
+
+struct btmtksdio_dev {
+ struct hci_dev *hdev;
+ struct sdio_func *func;
+
+ struct work_struct tx_work;
+ unsigned long tx_state;
+ struct sk_buff_head txq;
+
+ struct sk_buff *evt_skb;
+
+ const struct btmtksdio_data *data;
+};
+
+static int mtk_hci_wmt_sync(struct hci_dev *hdev,
+ struct btmtk_hci_wmt_params *wmt_params)
+{
+ struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+ struct btmtk_hci_wmt_evt_funcc *wmt_evt_funcc;
+ u32 hlen, status = BTMTK_WMT_INVALID;
+ struct btmtk_hci_wmt_evt *wmt_evt;
+ struct mtk_hci_wmt_cmd wc;
+ struct mtk_wmt_hdr *hdr;
+ int err;
+
+ hlen = sizeof(*hdr) + wmt_params->dlen;
+ if (hlen > 255)
+ return -EINVAL;
+
+ hdr = (struct mtk_wmt_hdr *)&wc;
+ hdr->dir = 1;
+ hdr->op = wmt_params->op;
+ hdr->dlen = cpu_to_le16(wmt_params->dlen + 1);
+ hdr->flag = wmt_params->flag;
+ memcpy(wc.data, wmt_params->data, wmt_params->dlen);
+
+ set_bit(BTMTKSDIO_TX_WAIT_VND_EVT, &bdev->tx_state);
+
+ err = __hci_cmd_send(hdev, 0xfc6f, hlen, &wc);
+ if (err < 0) {
+ clear_bit(BTMTKSDIO_TX_WAIT_VND_EVT, &bdev->tx_state);
+ return err;
+ }
+
+ /* The vendor specific WMT commands are all answered by a vendor
+ * specific event and will not have the Command Status or Command
+ * Complete as with usual HCI command flow control.
+ *
+ * After sending the command, wait for BTMTKSDIO_TX_WAIT_VND_EVT
+ * state to be cleared. The driver specific event receive routine
+ * will clear that state and with that indicate completion of the
+ * WMT command.
+ */
+ err = wait_on_bit_timeout(&bdev->tx_state, BTMTKSDIO_TX_WAIT_VND_EVT,
+ TASK_INTERRUPTIBLE, HCI_INIT_TIMEOUT);
+ if (err == -EINTR) {
+ bt_dev_err(hdev, "Execution of wmt command interrupted");
+ clear_bit(BTMTKSDIO_TX_WAIT_VND_EVT, &bdev->tx_state);
+ return err;
+ }
+
+ if (err) {
+ bt_dev_err(hdev, "Execution of wmt command timed out");
+ clear_bit(BTMTKSDIO_TX_WAIT_VND_EVT, &bdev->tx_state);
+ return -ETIMEDOUT;
+ }
+
+ /* Parse and handle the return WMT event */
+ wmt_evt = (struct btmtk_hci_wmt_evt *)bdev->evt_skb->data;
+ if (wmt_evt->whdr.op != hdr->op) {
+ bt_dev_err(hdev, "Wrong op received %d expected %d",
+ wmt_evt->whdr.op, hdr->op);
+ err = -EIO;
+ goto err_free_skb;
+ }
+
+ switch (wmt_evt->whdr.op) {
+ case MTK_WMT_SEMAPHORE:
+ if (wmt_evt->whdr.flag == 2)
+ status = BTMTK_WMT_PATCH_UNDONE;
+ else
+ status = BTMTK_WMT_PATCH_DONE;
+ break;
+ case MTK_WMT_FUNC_CTRL:
+ wmt_evt_funcc = (struct btmtk_hci_wmt_evt_funcc *)wmt_evt;
+ if (be16_to_cpu(wmt_evt_funcc->status) == 0x404)
+ status = BTMTK_WMT_ON_DONE;
+ else if (be16_to_cpu(wmt_evt_funcc->status) == 0x420)
+ status = BTMTK_WMT_ON_PROGRESS;
+ else
+ status = BTMTK_WMT_ON_UNDONE;
+ break;
+ }
+
+ if (wmt_params->status)
+ *wmt_params->status = status;
+
+err_free_skb:
+ kfree_skb(bdev->evt_skb);
+ bdev->evt_skb = NULL;
+
+ return err;
+}
+
+static int btmtksdio_tx_packet(struct btmtksdio_dev *bdev,
+ struct sk_buff *skb)
+{
+ struct mtkbtsdio_hdr *sdio_hdr;
+ int err;
+
+ /* Make sure that there are enough rooms for SDIO header */
+ if (unlikely(skb_headroom(skb) < sizeof(*sdio_hdr))) {
+ err = pskb_expand_head(skb, sizeof(*sdio_hdr), 0,
+ GFP_ATOMIC);
+ if (err < 0)
+ return err;
+ }
+
+ /* Prepend MediaTek SDIO Specific Header */
+ skb_push(skb, sizeof(*sdio_hdr));
+
+ sdio_hdr = (void *)skb->data;
+ sdio_hdr->len = cpu_to_le16(skb->len);
+ sdio_hdr->reserved = cpu_to_le16(0);
+ sdio_hdr->bt_type = hci_skb_pkt_type(skb);
+
+ err = sdio_writesb(bdev->func, MTK_REG_CTDR, skb->data,
+ round_up(skb->len, MTK_SDIO_BLOCK_SIZE));
+ if (err < 0)
+ goto err_skb_pull;
+
+ bdev->hdev->stat.byte_tx += skb->len;
+
+ kfree_skb(skb);
+
+ return 0;
+
+err_skb_pull:
+ skb_pull(skb, sizeof(*sdio_hdr));
+
+ return err;
+}
+
+static u32 btmtksdio_drv_own_query(struct btmtksdio_dev *bdev)
+{
+ return sdio_readl(bdev->func, MTK_REG_CHLPCR, NULL);
+}
+
+static void btmtksdio_tx_work(struct work_struct *work)
+{
+ struct btmtksdio_dev *bdev = container_of(work, struct btmtksdio_dev,
+ tx_work);
+ struct sk_buff *skb;
+ int err;
+
+ sdio_claim_host(bdev->func);
+
+ while ((skb = skb_dequeue(&bdev->txq))) {
+ err = btmtksdio_tx_packet(bdev, skb);
+ if (err < 0) {
+ bdev->hdev->stat.err_tx++;
+ skb_queue_head(&bdev->txq, skb);
+ break;
+ }
+ }
+
+ sdio_release_host(bdev->func);
+}
+
+static int btmtksdio_recv_event(struct hci_dev *hdev, struct sk_buff *skb)
+{
+ struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+ struct hci_event_hdr *hdr = (void *)skb->data;
+ int err;
+
+ /* Fix up the vendor event id with 0xff for vendor specific instead
+ * of 0xe4 so that event send via monitoring socket can be parsed
+ * properly.
+ */
+ if (hdr->evt == 0xe4)
+ hdr->evt = HCI_EV_VENDOR;
+
+ /* When someone waits for the WMT event, the skb is being cloned
+ * and being processed the events from there then.
+ */
+ if (test_bit(BTMTKSDIO_TX_WAIT_VND_EVT, &bdev->tx_state)) {
+ bdev->evt_skb = skb_clone(skb, GFP_KERNEL);
+ if (!bdev->evt_skb) {
+ err = -ENOMEM;
+ goto err_out;
+ }
+ }
+
+ err = hci_recv_frame(hdev, skb);
+ if (err < 0)
+ goto err_free_skb;
+
+ if (hdr->evt == HCI_EV_VENDOR) {
+ if (test_and_clear_bit(BTMTKSDIO_TX_WAIT_VND_EVT,
+ &bdev->tx_state)) {
+ /* Barrier to sync with other CPUs */
+ smp_mb__after_atomic();
+ wake_up_bit(&bdev->tx_state, BTMTKSDIO_TX_WAIT_VND_EVT);
+ }
+ }
+
+ return 0;
+
+err_free_skb:
+ kfree_skb(bdev->evt_skb);
+ bdev->evt_skb = NULL;
+
+err_out:
+ return err;
+}
+
+static const struct h4_recv_pkt mtk_recv_pkts[] = {
+ { H4_RECV_ACL, .recv = hci_recv_frame },
+ { H4_RECV_SCO, .recv = hci_recv_frame },
+ { H4_RECV_EVENT, .recv = btmtksdio_recv_event },
+};
+
+static int btmtksdio_rx_packet(struct btmtksdio_dev *bdev, u16 rx_size)
+{
+ const struct h4_recv_pkt *pkts = mtk_recv_pkts;
+ int pkts_count = ARRAY_SIZE(mtk_recv_pkts);
+ struct mtkbtsdio_hdr *sdio_hdr;
+ unsigned char *old_data;
+ unsigned int old_len;
+ int err, i, pad_size;
+ struct sk_buff *skb;
+ u16 dlen;
+
+ if (rx_size < sizeof(*sdio_hdr))
+ return -EILSEQ;
+
+ /* A SDIO packet is exactly containing a Bluetooth packet */
+ skb = bt_skb_alloc(rx_size, GFP_KERNEL);
+ if (!skb)
+ return -ENOMEM;
+
+ skb_put(skb, rx_size);
+
+ err = sdio_readsb(bdev->func, skb->data, MTK_REG_CRDR, rx_size);
+ if (err < 0)
+ goto err_kfree_skb;
+
+ /* Keep old data for dump the content in case of some error is
+ * caught in the following packet parsing.
+ */
+ old_data = skb->data;
+ old_len = skb->len;
+
+ bdev->hdev->stat.byte_rx += rx_size;
+
+ sdio_hdr = (void *)skb->data;
+
+ /* We assume the default error as -EILSEQ simply to make the error path
+ * be cleaner.
+ */
+ err = -EILSEQ;
+
+ if (rx_size != le16_to_cpu(sdio_hdr->len)) {
+ bt_dev_err(bdev->hdev, "Rx size in sdio header is mismatched ");
+ goto err_kfree_skb;
+ }
+
+ hci_skb_pkt_type(skb) = sdio_hdr->bt_type;
+
+ /* Remove MediaTek SDIO header */
+ skb_pull(skb, sizeof(*sdio_hdr));
+
+ /* We have to dig into the packet to get payload size and then know how
+ * many padding bytes at the tail, these padding bytes should be removed
+ * before the packet is indicated to the core layer.
+ */
+ for (i = 0; i < pkts_count; i++) {
+ if (sdio_hdr->bt_type == (&pkts[i])->type)
+ break;
+ }
+
+ if (i >= pkts_count) {
+ bt_dev_err(bdev->hdev, "Invalid bt type 0x%02x",
+ sdio_hdr->bt_type);
+ goto err_kfree_skb;
+ }
+
+ /* Remaining bytes cannot hold a header*/
+ if (skb->len < (&pkts[i])->hlen) {
+ bt_dev_err(bdev->hdev, "The size of bt header is mismatched");
+ goto err_kfree_skb;
+ }
+
+ switch ((&pkts[i])->lsize) {
+ case 1:
+ dlen = skb->data[(&pkts[i])->loff];
+ break;
+ case 2:
+ dlen = get_unaligned_le16(skb->data +
+ (&pkts[i])->loff);
+ break;
+ default:
+ goto err_kfree_skb;
+ }
+
+ pad_size = skb->len - (&pkts[i])->hlen - dlen;
+
+ /* Remaining bytes cannot hold a payload */
+ if (pad_size < 0) {
+ bt_dev_err(bdev->hdev, "The size of bt payload is mismatched");
+ goto err_kfree_skb;
+ }
+
+ /* Remove padding bytes */
+ skb_trim(skb, skb->len - pad_size);
+
+ /* Complete frame */
+ (&pkts[i])->recv(bdev->hdev, skb);
+
+ return 0;
+
+err_kfree_skb:
+ print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
+ old_data, old_len, true);
+ kfree_skb(skb);
+
+ return err;
+}
+
+static void btmtksdio_interrupt(struct sdio_func *func)
+{
+ struct btmtksdio_dev *bdev = sdio_get_drvdata(func);
+ u32 int_status;
+ u16 rx_size;
+
+ /* Disable interrupt */
+ sdio_writel(func, C_INT_EN_CLR, MTK_REG_CHLPCR, 0);
+
+ int_status = sdio_readl(func, MTK_REG_CHISR, NULL);
+
+ /* Ack an interrupt as soon as possible before any operation on
+ * hardware.
+ *
+ * Note that we don't ack any status during operations to avoid race
+ * condition between the host and the device such as it's possible to
+ * mistakenly ack RX_DONE for the next packet and then cause interrupts
+ * not be raised again but there is still pending data in the hardware
+ * FIFO.
+ */
+ sdio_writel(func, int_status, MTK_REG_CHISR, NULL);
+
+ if (unlikely(!int_status))
+ bt_dev_err(bdev->hdev, "CHISR is 0\n");
+
+ if (int_status & FW_OWN_BACK_INT)
+ bt_dev_dbg(bdev->hdev, "Get fw own back\n");
+
+ if (int_status & TX_EMPTY)
+ schedule_work(&bdev->tx_work);
+ else if (unlikely(int_status & TX_FIFO_OVERFLOW))
+ bt_dev_warn(bdev->hdev, "Tx fifo overflow\n");
+
+ if (int_status & RX_DONE_INT) {
+ rx_size = (int_status & RX_PKT_LEN) >> 16;
+
+ if (btmtksdio_rx_packet(bdev, rx_size) < 0)
+ bdev->hdev->stat.err_rx++;
+ }
+
+ /* Enable interrupt */
+ sdio_writel(func, C_INT_EN_SET, MTK_REG_CHLPCR, 0);
+}
+
+static int btmtksdio_open(struct hci_dev *hdev)
+{
+ struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+ int err;
+ u32 status;
+
+ sdio_claim_host(bdev->func);
+
+ err = sdio_enable_func(bdev->func);
+ if (err < 0)
+ goto err_release_host;
+
+ /* Get ownership from the device */
+ sdio_writel(bdev->func, C_FW_OWN_REQ_CLR, MTK_REG_CHLPCR, &err);
+ if (err < 0)
+ goto err_disable_func;
+
+ err = readx_poll_timeout(btmtksdio_drv_own_query, bdev, status,
+ status & C_FW_OWN_REQ_SET, 2000, 1000000);
+ if (err < 0) {
+ bt_dev_err(bdev->hdev, "Cannot get ownership from device");
+ goto err_disable_func;
+ }
+
+ /* Disable interrupt & mask out all interrupt sources */
+ sdio_writel(bdev->func, C_INT_EN_CLR, MTK_REG_CHLPCR, &err);
+ if (err < 0)
+ goto err_disable_func;
+
+ sdio_writel(bdev->func, 0, MTK_REG_CHIER, &err);
+ if (err < 0)
+ goto err_disable_func;
+
+ err = sdio_claim_irq(bdev->func, btmtksdio_interrupt);
+ if (err < 0)
+ goto err_disable_func;
+
+ err = sdio_set_block_size(bdev->func, MTK_SDIO_BLOCK_SIZE);
+ if (err < 0)
+ goto err_release_irq;
+
+ /* SDIO CMD 5 allows the SDIO device back to idle state an
+ * synchronous interrupt is supported in SDIO 4-bit mode
+ */
+ sdio_writel(bdev->func, SDIO_INT_CTL | SDIO_RE_INIT_EN,
+ MTK_REG_CSDIOCSR, &err);
+ if (err < 0)
+ goto err_release_irq;
+
+ /* Setup write-1-clear for CHISR register */
+ sdio_writel(bdev->func, C_INT_CLR_CTRL, MTK_REG_CHCR, &err);
+ if (err < 0)
+ goto err_release_irq;
+
+ /* Setup interrupt sources */
+ sdio_writel(bdev->func, RX_DONE_INT | TX_EMPTY | TX_FIFO_OVERFLOW,
+ MTK_REG_CHIER, &err);
+ if (err < 0)
+ goto err_release_irq;
+
+ /* Enable interrupt */
+ sdio_writel(bdev->func, C_INT_EN_SET, MTK_REG_CHLPCR, &err);
+ if (err < 0)
+ goto err_release_irq;
+
+ sdio_release_host(bdev->func);
+
+ return 0;
+
+err_release_irq:
+ sdio_release_irq(bdev->func);
+
+err_disable_func:
+ sdio_disable_func(bdev->func);
+
+err_release_host:
+ sdio_release_host(bdev->func);
+
+ return err;
+}
+
+static int btmtksdio_close(struct hci_dev *hdev)
+{
+ struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+ u32 status;
+ int err;
+
+ sdio_claim_host(bdev->func);
+
+ /* Disable interrupt */
+ sdio_writel(bdev->func, C_INT_EN_CLR, MTK_REG_CHLPCR, NULL);
+
+ sdio_release_irq(bdev->func);
+
+ /* Return ownership to the device */
+ sdio_writel(bdev->func, C_FW_OWN_REQ_SET, MTK_REG_CHLPCR, NULL);
+
+ err = readx_poll_timeout(btmtksdio_drv_own_query, bdev, status,
+ !(status & C_FW_OWN_REQ_SET), 2000, 1000000);
+ if (err < 0)
+ bt_dev_err(bdev->hdev, "Cannot return ownership to device");
+
+ sdio_disable_func(bdev->func);
+
+ sdio_release_host(bdev->func);
+
+ return 0;
+}
+
+static int btmtksdio_flush(struct hci_dev *hdev)
+{
+ struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+
+ skb_queue_purge(&bdev->txq);
+
+ cancel_work_sync(&bdev->tx_work);
+
+ return 0;
+}
+
+static int btmtksdio_func_query(struct hci_dev *hdev)
+{
+ struct btmtk_hci_wmt_params wmt_params;
+ int status, err;
+ u8 param = 0;
+
+ /* Query whether the function is enabled */
+ wmt_params.op = MTK_WMT_FUNC_CTRL;
+ wmt_params.flag = 4;
+ wmt_params.dlen = sizeof(param);
+ wmt_params.data = &param;
+ wmt_params.status = &status;
+
+ err = mtk_hci_wmt_sync(hdev, &wmt_params);
+ if (err < 0) {
+ bt_dev_err(hdev, "Failed to query function status (%d)", err);
+ return err;
+ }
+
+ return status;
+}
+
+static int mtk_setup_firmware(struct hci_dev *hdev, const char *fwname)
+{
+ struct btmtk_hci_wmt_params wmt_params;
+ const struct firmware *fw;
+ const u8 *fw_ptr;
+ size_t fw_size;
+ int err, dlen;
+ u8 flag;
+
+ err = request_firmware(&fw, fwname, &hdev->dev);
+ if (err < 0) {
+ bt_dev_err(hdev, "Failed to load firmware file (%d)", err);
+ return err;
+ }
+
+ fw_ptr = fw->data;
+ fw_size = fw->size;
+
+ /* The size of patch header is 30 bytes, should be skip */
+ if (fw_size < 30) {
+ err = -EINVAL;
+ goto free_fw;
+ }
+
+ fw_size -= 30;
+ fw_ptr += 30;
+ flag = 1;
+
+ wmt_params.op = MTK_WMT_PATCH_DWNLD;
+ wmt_params.status = NULL;
+
+ while (fw_size > 0) {
+ dlen = min_t(int, 250, fw_size);
+
+ /* Tell device the position in sequence */
+ if (fw_size - dlen <= 0)
+ flag = 3;
+ else if (fw_size < fw->size - 30)
+ flag = 2;
+
+ wmt_params.flag = flag;
+ wmt_params.dlen = dlen;
+ wmt_params.data = fw_ptr;
+
+ err = mtk_hci_wmt_sync(hdev, &wmt_params);
+ if (err < 0) {
+ bt_dev_err(hdev, "Failed to send wmt patch dwnld (%d)",
+ err);
+ goto free_fw;
+ }
+
+ fw_size -= dlen;
+ fw_ptr += dlen;
+ }
+
+ wmt_params.op = MTK_WMT_RST;
+ wmt_params.flag = 4;
+ wmt_params.dlen = 0;
+ wmt_params.data = NULL;
+ wmt_params.status = NULL;
+
+ /* Activate funciton the firmware providing to */
+ err = mtk_hci_wmt_sync(hdev, &wmt_params);
+ if (err < 0) {
+ bt_dev_err(hdev, "Failed to send wmt rst (%d)", err);
+ goto free_fw;
+ }
+
+ /* Wait a few moments for firmware activation done */
+ usleep_range(10000, 12000);
+
+free_fw:
+ release_firmware(fw);
+ return err;
+}
+
+static int btmtksdio_setup(struct hci_dev *hdev)
+{
+ struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+ struct btmtk_hci_wmt_params wmt_params;
+ ktime_t calltime, delta, rettime;
+ struct btmtk_tci_sleep tci_sleep;
+ unsigned long long duration;
+ struct sk_buff *skb;
+ int err, status;
+ u8 param = 0x1;
+
+ calltime = ktime_get();
+
+ /* Query whether the firmware is already download */
+ wmt_params.op = MTK_WMT_SEMAPHORE;
+ wmt_params.flag = 1;
+ wmt_params.dlen = 0;
+ wmt_params.data = NULL;
+ wmt_params.status = &status;
+
+ err = mtk_hci_wmt_sync(hdev, &wmt_params);
+ if (err < 0) {
+ bt_dev_err(hdev, "Failed to query firmware status (%d)", err);
+ return err;
+ }
+
+ if (status == BTMTK_WMT_PATCH_DONE) {
+ bt_dev_info(hdev, "Firmware already downloaded");
+ goto ignore_setup_fw;
+ }
+
+ /* Setup a firmware which the device definitely requires */
+ err = mtk_setup_firmware(hdev, bdev->data->fwname);
+ if (err < 0)
+ return err;
+
+ignore_setup_fw:
+ /* Query whether the device is already enabled */
+ err = readx_poll_timeout(btmtksdio_func_query, hdev, status,
+ status < 0 || status != BTMTK_WMT_ON_PROGRESS,
+ 2000, 5000000);
+ /* -ETIMEDOUT happens */
+ if (err < 0)
+ return err;
+
+ /* The other errors happen in btusb_mtk_func_query */
+ if (status < 0)
+ return status;
+
+ if (status == BTMTK_WMT_ON_DONE) {
+ bt_dev_info(hdev, "function already on");
+ goto ignore_func_on;
+ }
+
+ /* Enable Bluetooth protocol */
+ wmt_params.op = MTK_WMT_FUNC_CTRL;
+ wmt_params.flag = 0;
+ wmt_params.dlen = sizeof(param);
+ wmt_params.data = &param;
+ wmt_params.status = NULL;
+
+ err = mtk_hci_wmt_sync(hdev, &wmt_params);
+ if (err < 0) {
+ bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
+ return err;
+ }
+
+ignore_func_on:
+ /* Apply the low power environment setup */
+ tci_sleep.mode = 0x5;
+ tci_sleep.duration = cpu_to_le16(0x640);
+ tci_sleep.host_duration = cpu_to_le16(0x640);
+ tci_sleep.host_wakeup_pin = 0;
+ tci_sleep.time_compensation = 0;
+
+ skb = __hci_cmd_sync(hdev, 0xfc7a, sizeof(tci_sleep), &tci_sleep,
+ HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ err = PTR_ERR(skb);
+ bt_dev_err(hdev, "Failed to apply low power setting (%d)", err);
+ return err;
+ }
+ kfree_skb(skb);
+
+ rettime = ktime_get();
+ delta = ktime_sub(rettime, calltime);
+ duration = (unsigned long long)ktime_to_ns(delta) >> 10;
+
+ bt_dev_info(hdev, "Device setup in %llu usecs", duration);
+
+ return 0;
+}
+
+static int btmtksdio_shutdown(struct hci_dev *hdev)
+{
+ struct btmtk_hci_wmt_params wmt_params;
+ u8 param = 0x0;
+ int err;
+
+ /* Disable the device */
+ wmt_params.op = MTK_WMT_FUNC_CTRL;
+ wmt_params.flag = 0;
+ wmt_params.dlen = sizeof(param);
+ wmt_params.data = &param;
+ wmt_params.status = NULL;
+
+ err = mtk_hci_wmt_sync(hdev, &wmt_params);
+ if (err < 0) {
+ bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
+ return err;
+ }
+
+ return 0;
+}
+
+static int btmtksdio_send_frame(struct hci_dev *hdev, struct sk_buff *skb)
+{
+ struct btmtksdio_dev *bdev = hci_get_drvdata(hdev);
+
+ switch (hci_skb_pkt_type(skb)) {
+ case HCI_COMMAND_PKT:
+ hdev->stat.cmd_tx++;
+ break;
+
+ case HCI_ACLDATA_PKT:
+ hdev->stat.acl_tx++;
+ break;
+
+ case HCI_SCODATA_PKT:
+ hdev->stat.sco_tx++;
+ break;
+
+ default:
+ return -EILSEQ;
+ }
+
+ skb_queue_tail(&bdev->txq, skb);
+
+ schedule_work(&bdev->tx_work);
+
+ return 0;
+}
+
+static int btmtksdio_probe(struct sdio_func *func,
+ const struct sdio_device_id *id)
+{
+ struct btmtksdio_dev *bdev;
+ struct hci_dev *hdev;
+ int err;
+
+ bdev = devm_kzalloc(&func->dev, sizeof(*bdev), GFP_KERNEL);
+ if (!bdev)
+ return -ENOMEM;
+
+ bdev->data = (void *)id->driver_data;
+ if (!bdev->data)
+ return -ENODEV;
+
+ bdev->func = func;
+
+ INIT_WORK(&bdev->tx_work, btmtksdio_tx_work);
+ skb_queue_head_init(&bdev->txq);
+
+ /* Initialize and register HCI device */
+ hdev = hci_alloc_dev();
+ if (!hdev) {
+ dev_err(&func->dev, "Can't allocate HCI device\n");
+ return -ENOMEM;
+ }
+
+ bdev->hdev = hdev;
+
+ hdev->bus = HCI_SDIO;
+ hci_set_drvdata(hdev, bdev);
+
+ hdev->open = btmtksdio_open;
+ hdev->close = btmtksdio_close;
+ hdev->flush = btmtksdio_flush;
+ hdev->setup = btmtksdio_setup;
+ hdev->shutdown = btmtksdio_shutdown;
+ hdev->send = btmtksdio_send_frame;
+ SET_HCIDEV_DEV(hdev, &func->dev);
+
+ hdev->manufacturer = 70;
+ set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);
+
+ err = hci_register_dev(hdev);
+ if (err < 0) {
+ dev_err(&func->dev, "Can't register HCI device\n");
+ hci_free_dev(hdev);
+ return err;
+ }
+
+ sdio_set_drvdata(func, bdev);
+
+ return 0;
+}
+
+static void btmtksdio_remove(struct sdio_func *func)
+{
+ struct btmtksdio_dev *bdev = sdio_get_drvdata(func);
+ struct hci_dev *hdev;
+
+ if (!bdev)
+ return;
+
+ hdev = bdev->hdev;
+
+ sdio_set_drvdata(func, NULL);
+ hci_unregister_dev(hdev);
+ hci_free_dev(hdev);
+}
+
+static struct sdio_driver btmtksdio_driver = {
+ .name = "btmtksdio",
+ .probe = btmtksdio_probe,
+ .remove = btmtksdio_remove,
+ .id_table = btmtksdio_table,
+};
+
+static int __init btmtksdio_init(void)
+{
+ BT_INFO("MediaTek Bluetooth SDIO driver ver %s", VERSION);
+
+ return sdio_register_driver(&btmtksdio_driver);
+}
+
+static void __exit btmtksdio_exit(void)
+{
+ sdio_unregister_driver(&btmtksdio_driver);
+}
+
+module_init(btmtksdio_init);
+module_exit(btmtksdio_exit);
+
+MODULE_AUTHOR("Sean Wang <sean.wang@mediatek.com>");
+MODULE_DESCRIPTION("MediaTek Bluetooth SDIO driver ver " VERSION);
+MODULE_VERSION(VERSION);
+MODULE_LICENSE("GPL");
+MODULE_FIRMWARE(FIRMWARE_MT7663);
+MODULE_FIRMWARE(FIRMWARE_MT7668);
--
2.18.0