[PATCH v5 6/6] usb: musb: Add support for MediaTek musb controller

min.guo
2019-02-19T07:36:35Z

This adds support for MediaTek musb controller in
host, peripheral and otg mode.
There are some quirk of MediaTek musb controller, such as:
-W1C interrupt status registers
-Private data toggle registers
-No dedicated DMA interrupt line

Signed-off-by: Min Guo <min.guo@mediatek.com>
Signed-off-by: Yonglong Wu <yonglong.wu@mediatek.com>
---
changes in v5:
1. Replace musb_readb() with musb_clearb() to clear common/tx/rx pending interrupts
2. Make musb_clearb/w() return the value of musb_readb/w()
3. Add driver to get child nodes of usb connector and extcon device

changes in v4:
1. no changes

changes in v3:
suggested by Bin:
1. Remove 'u8/u16 data' parameter in clearb/w() hooks
2. Replace musb_readb/w() with musb_clearb/w() to clear interrupts status

changes in v2:
suggested by Bin:
1. Add summarize of MediaTek musb controller differences in the commit log
2. Add "|| COMPILE_TEST" in Kconfig
3. Move MediaTek's private toggle registers from musb_regs.h to mediatek.c
4. Replace musb_readl() with musb_readw() to read 16bit toggle register
---
drivers/usb/musb/Kconfig | 8 +-
drivers/usb/musb/Makefile | 1 +
drivers/usb/musb/mediatek.c | 629 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 637 insertions(+), 1 deletion(-)
create mode 100644 drivers/usb/musb/mediatek.c

diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig
index ad08895..b72b7c1 100644
--- a/drivers/usb/musb/Kconfig
+++ b/drivers/usb/musb/Kconfig
@@ -115,6 +115,12 @@ config USB_MUSB_JZ4740
depends on USB_MUSB_GADGET
depends on USB_OTG_BLACKLIST_HUB

+config USB_MUSB_MEDIATEK
+ tristate "MediaTek platforms"
+ depends on ARCH_MEDIATEK || COMPILE_TEST
+ depends on NOP_USB_XCEIV
+ depends on GENERIC_PHY
+
config USB_MUSB_AM335X_CHILD
tristate

@@ -141,7 +147,7 @@ config USB_UX500_DMA

config USB_INVENTRA_DMA
bool 'Inventra'
- depends on USB_MUSB_OMAP2PLUS
+ depends on USB_MUSB_OMAP2PLUS || USB_MUSB_MEDIATEK
help
Enable DMA transfers using Mentor's engine.

diff --git a/drivers/usb/musb/Makefile b/drivers/usb/musb/Makefile
index 3a88c79..63d82d0 100644
--- a/drivers/usb/musb/Makefile
+++ b/drivers/usb/musb/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_USB_MUSB_DA8XX) += da8xx.o
obj-$(CONFIG_USB_MUSB_UX500) += ux500.o
obj-$(CONFIG_USB_MUSB_JZ4740) += jz4740.o
obj-$(CONFIG_USB_MUSB_SUNXI) += sunxi.o
+obj-$(CONFIG_USB_MUSB_MEDIATEK) += mediatek.o

obj-$(CONFIG_USB_MUSB_AM335X_CHILD) += musb_am335x.o
diff --git a/drivers/usb/musb/mediatek.c b/drivers/usb/musb/mediatek.c
new file mode 100644
index 0000000..946b453
--- /dev/null
+++ b/drivers/usb/musb/mediatek.c
@@ -0,0 +1,629 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 MediaTek Inc.
+ *
+ * Author:
+ * Min Guo <min.guo@mediatek.com>
+ * Yonglong Wu <yonglong.wu@mediatek.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/usb/usb_phy_generic.h>
+#include "musb_core.h"
+#include "musb_dma.h"
+
+#define USB_L1INTS 0x00a0
+#define USB_L1INTM 0x00a4
+#define MTK_MUSB_TXFUNCADDR 0x0480
+
+/* MediaTek controller toggle enable and status reg */
+#define MUSB_RXTOG 0x80
+#define MUSB_RXTOGEN 0x82
+#define MUSB_TXTOG 0x84
+#define MUSB_TXTOGEN 0x86
+
+#define TX_INT_STATUS BIT(0)
+#define RX_INT_STATUS BIT(1)
+#define USBCOM_INT_STATUS BIT(2)
+#define DMA_INT_STATUS BIT(3)
+
+#define DMA_INTR_STATUS_MSK GENMASK(7, 0)
+#define DMA_INTR_UNMASK_SET_MSK GENMASK(31, 24)
+
+enum mtk_vbus_id_state {
+ MTK_ID_FLOAT = 1,
+ MTK_ID_GROUND,
+ MTK_VBUS_OFF,
+ MTK_VBUS_VALID,
+};
+
+struct mtk_glue {
+ struct device *dev;
+ struct musb *musb;
+ struct platform_device *musb_pdev;
+ struct platform_device *usb_phy;
+ struct phy *phy;
+ struct usb_phy *xceiv;
+ enum phy_mode phy_mode;
+ struct clk *main;
+ struct clk *mcu;
+ struct clk *univpll;
+ struct regulator *vbus;
+ struct extcon_dev *edev;
+ struct notifier_block vbus_nb;
+ struct notifier_block id_nb;
+};
+
+static int mtk_musb_clks_get(struct mtk_glue *glue)
+{
+ struct device *dev = glue->dev;
+
+ glue->main = devm_clk_get(dev, "main");
+ if (IS_ERR(glue->main)) {
+ dev_err(dev, "fail to get main clock\n");
+ return PTR_ERR(glue->main);
+ }
+
+ glue->mcu = devm_clk_get(dev, "mcu");
+ if (IS_ERR(glue->mcu)) {
+ dev_err(dev, "fail to get mcu clock\n");
+ return PTR_ERR(glue->mcu);
+ }
+
+ glue->univpll = devm_clk_get(dev, "univpll");
+ if (IS_ERR(glue->univpll)) {
+ dev_err(dev, "fail to get univpll clock\n");
+ return PTR_ERR(glue->univpll);
+ }
+
+ return 0;
+}
+
+static int mtk_musb_clks_enable(struct mtk_glue *glue)
+{
+ int ret;
+
+ ret = clk_prepare_enable(glue->main);
+ if (ret) {
+ dev_err(glue->dev, "failed to enable main clock\n");
+ goto err_main_clk;
+ }
+
+ ret = clk_prepare_enable(glue->mcu);
+ if (ret) {
+ dev_err(glue->dev, "failed to enable mcu clock\n");
+ goto err_mcu_clk;
+ }
+
+ ret = clk_prepare_enable(glue->univpll);
+ if (ret) {
+ dev_err(glue->dev, "failed to enable univpll clock\n");
+ goto err_univpll_clk;
+ }
+
+ return 0;
+
+err_univpll_clk:
+ clk_disable_unprepare(glue->mcu);
+err_mcu_clk:
+ clk_disable_unprepare(glue->main);
+err_main_clk:
+ return ret;
+}
+
+static void mtk_musb_clks_disable(struct mtk_glue *glue)
+{
+ clk_disable_unprepare(glue->univpll);
+ clk_disable_unprepare(glue->mcu);
+ clk_disable_unprepare(glue->main);
+}
+
+static void mtk_musb_set_vbus(struct musb *musb, int is_on)
+{
+ struct device *dev = musb->controller;
+ struct mtk_glue *glue = dev_get_drvdata(dev->parent);
+ int ret;
+
+ /* vbus is optional */
+ if (!glue->vbus)
+ return;
+
+ dev_dbg(musb->controller, "%s, is_on=%d\r\n", __func__, is_on);
+ if (is_on) {
+ ret = regulator_enable(glue->vbus);
+ if (ret) {
+ dev_err(glue->dev, "fail to enable vbus regulator\n");
+ return;
+ }
+ } else {
+ regulator_disable(glue->vbus);
+ }
+}
+
+/*
+ * switch to host: -> MTK_VBUS_OFF --> MTK_ID_GROUND
+ * switch to device: -> MTK_ID_FLOAT --> MTK_VBUS_VALID
+ */
+static void mtk_musb_set_mailbox(struct mtk_glue *glue,
+ enum mtk_vbus_id_state status)
+{
+ struct musb *musb = glue->musb;
+ u8 devctl = 0;
+
+ dev_dbg(glue->dev, "mailbox state(%d)\n", status);
+ switch (status) {
+ case MTK_ID_GROUND:
+ phy_power_on(glue->phy);
+ devctl = readb(musb->mregs + MUSB_DEVCTL);
+ musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
+ mtk_musb_set_vbus(musb, 1);
+ glue->phy_mode = PHY_MODE_USB_HOST;
+ phy_set_mode(glue->phy, glue->phy_mode);
+ devctl |= MUSB_DEVCTL_SESSION;
+ musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
+ MUSB_HST_MODE(musb);
+ break;
+ /*
+ * MTK_ID_FLOAT process is the same as MTK_VBUS_VALID
+ * except that turn off VBUS
+ */
+ case MTK_ID_FLOAT:
+ mtk_musb_set_vbus(musb, 0);
+ /* fall through */
+ case MTK_VBUS_OFF:
+ musb->xceiv->otg->state = OTG_STATE_B_IDLE;
+ devctl &= ~MUSB_DEVCTL_SESSION;
+ musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
+ phy_power_off(glue->phy);
+ break;
+ case MTK_VBUS_VALID:
+ phy_power_on(glue->phy);
+ glue->phy_mode = PHY_MODE_USB_DEVICE;
+ phy_set_mode(glue->phy, glue->phy_mode);
+ MUSB_DEV_MODE(musb);
+ break;
+ default:
+ dev_err(glue->dev, "invalid state\n");
+ }
+}
+
+static int mtk_musb_id_notifier(struct notifier_block *nb,
+ unsigned long event, void *ptr)
+{
+ struct mtk_glue *glue = container_of(nb, struct mtk_glue, id_nb);
+
+ if (event)
+ mtk_musb_set_mailbox(glue, MTK_ID_GROUND);
+ else
+ mtk_musb_set_mailbox(glue, MTK_ID_FLOAT);
+
+ return NOTIFY_DONE;
+}
+
+static int mtk_musb_vbus_notifier(struct notifier_block *nb,
+ unsigned long event, void *ptr)
+{
+ struct mtk_glue *glue = container_of(nb, struct mtk_glue, vbus_nb);
+
+ if (event)
+ mtk_musb_set_mailbox(glue, MTK_VBUS_VALID);
+ else
+ mtk_musb_set_mailbox(glue, MTK_VBUS_OFF);
+
+ return NOTIFY_DONE;
+}
+
+static void mtk_otg_switch_init(struct mtk_glue *glue)
+{
+ int ret;
+
+ /* extcon is optional */
+ if (!glue->edev)
+ return;
+
+ glue->vbus_nb.notifier_call = mtk_musb_vbus_notifier;
+ ret = devm_extcon_register_notifier(glue->dev, glue->edev, EXTCON_USB,
+ &glue->vbus_nb);
+ if (ret < 0)
+ dev_err(glue->dev, "failed to register notifier for USB\n");
+
+ glue->id_nb.notifier_call = mtk_musb_id_notifier;
+ ret = devm_extcon_register_notifier(glue->dev, glue->edev,
+ EXTCON_USB_HOST, &glue->id_nb);
+ if (ret < 0)
+ dev_err(glue->dev, "failed to register notifier for USB-HOST\n");
+
+ dev_dbg(glue->dev, "EXTCON_USB: %d, EXTCON_USB_HOST: %d\n",
+ extcon_get_state(glue->edev, EXTCON_USB),
+ extcon_get_state(glue->edev, EXTCON_USB_HOST));
+
+ /* default as host, switch to device mode if needed */
+ if (extcon_get_state(glue->edev, EXTCON_USB_HOST) == false)
+ mtk_musb_set_mailbox(glue, MTK_ID_FLOAT);
+ if (extcon_get_state(glue->edev, EXTCON_USB) == true)
+ mtk_musb_set_mailbox(glue, MTK_VBUS_VALID);
+}
+
+static irqreturn_t generic_interrupt(int irq, void *__hci)
+{
+ unsigned long flags;
+ irqreturn_t retval = IRQ_NONE;
+ struct musb *musb = __hci;
+
+ spin_lock_irqsave(&musb->lock, flags);
+ musb->int_usb = musb_clearb(musb->mregs, MUSB_INTRUSB);
+ musb->int_rx = musb_clearw(musb->mregs, MUSB_INTRRX);
+ musb->int_tx = musb_clearw(musb->mregs, MUSB_INTRTX);
+
+ if (musb->int_usb || musb->int_tx || musb->int_rx)
+ retval = musb_interrupt(musb);
+
+ spin_unlock_irqrestore(&musb->lock, flags);
+
+ return retval;
+}
+
+static irqreturn_t mtk_musb_interrupt(int irq, void *dev_id)
+{
+ irqreturn_t retval = IRQ_NONE;
+ struct musb *musb = (struct musb *)dev_id;
+ u32 l1_ints;
+
+ l1_ints = musb_readl(musb->mregs, USB_L1INTS) &
+ musb_readl(musb->mregs, USB_L1INTM);
+
+ if (l1_ints & (TX_INT_STATUS | RX_INT_STATUS | USBCOM_INT_STATUS))
+ retval = generic_interrupt(irq, musb);
+
+#if defined(CONFIG_USB_INVENTRA_DMA)
+ if (l1_ints & DMA_INT_STATUS)
+ retval = dma_controller_irq(irq, musb->dma_controller);
+#endif
+ return retval;
+}
+
+static u32 mtk_musb_busctl_offset(u8 epnum, u16 offset)
+{
+ return MTK_MUSB_TXFUNCADDR + offset + 8 * epnum;
+}
+
+static u8 mtk_musb_clearb(void __iomem *addr, unsigned int offset)
+{
+ u8 data;
+
+ /* W1C */
+ data = musb_readb(addr, offset);
+ musb_writeb(addr, offset, data);
+ return data;
+}
+
+static u16 mtk_musb_clearw(void __iomem *addr, unsigned int offset)
+{
+ u16 data;
+
+ /* W1C */
+ data = musb_readw(addr, offset);
+ musb_writew(addr, offset, data);
+ return data;
+}
+
+static int mtk_musb_init(struct musb *musb)
+{
+ struct device *dev = musb->controller;
+ struct mtk_glue *glue = dev_get_drvdata(dev->parent);
+ int ret;
+
+ glue->musb = musb;
+ musb->phy = glue->phy;
+ musb->xceiv = glue->xceiv;
+ musb->is_host = false;
+ musb->isr = mtk_musb_interrupt;
+ ret = phy_init(glue->phy);
+ if (ret)
+ return ret;
+
+ ret = phy_power_on(glue->phy);
+ if (ret) {
+ phy_exit(glue->phy);
+ return ret;
+ }
+
+ phy_set_mode(glue->phy, glue->phy_mode);
+
+#if defined(CONFIG_USB_INVENTRA_DMA)
+ musb_writel(musb->mregs, MUSB_HSDMA_INTR,
+ DMA_INTR_STATUS_MSK | DMA_INTR_UNMASK_SET_MSK);
+#endif
+ musb_writel(musb->mregs, USB_L1INTM, TX_INT_STATUS | RX_INT_STATUS |
+ USBCOM_INT_STATUS | DMA_INT_STATUS);
+ return 0;
+}
+
+static u16 mtk_musb_get_toggle(struct musb_qh *qh, int is_out)
+{
+ struct musb *musb = qh->hw_ep->musb;
+ u8 epnum = qh->hw_ep->epnum;
+ u16 toggle;
+
+ if (is_out)
+ toggle = musb_readw(musb->mregs, MUSB_TXTOG);
+ else
+ toggle = musb_readw(musb->mregs, MUSB_RXTOG);
+
+ return toggle & (1 << epnum);
+}
+
+static u16 mtk_musb_set_toggle(struct musb_qh *qh, int is_out, struct urb *urb)
+{
+ struct musb *musb = qh->hw_ep->musb;
+ u8 epnum = qh->hw_ep->epnum;
+ u16 toggle;
+
+ toggle = usb_gettoggle(urb->dev, qh->epnum, is_out);
+
+ if (is_out) {
+ musb_writew(musb->mregs, MUSB_TXTOGEN, (1 << epnum));
+ musb_writew(musb->mregs, MUSB_TXTOG, (toggle << epnum));
+ } else {
+ musb_writew(musb->mregs, MUSB_RXTOGEN, (1 << epnum));
+ musb_writew(musb->mregs, MUSB_RXTOG, (toggle << epnum));
+ }
+
+ return 0;
+}
+
+static int mtk_musb_set_mode(struct musb *musb, u8 mode)
+{
+ struct device *dev = musb->controller;
+ struct mtk_glue *glue = dev_get_drvdata(dev->parent);
+ enum phy_mode new_mode;
+
+ switch (mode) {
+ case MUSB_HOST:
+ new_mode = PHY_MODE_USB_HOST;
+ mtk_musb_set_vbus(musb, 1);
+ break;
+ case MUSB_PERIPHERAL:
+ new_mode = PHY_MODE_USB_DEVICE;
+ break;
+ case MUSB_OTG:
+ new_mode = PHY_MODE_USB_HOST;
+ break;
+ default:
+ dev_err(musb->controller->parent,
+ "Error requested mode not supported by this kernel\n");
+ return -EINVAL;
+ }
+ if (glue->phy_mode == new_mode)
+ return 0;
+
+ mtk_musb_set_mailbox(glue, MTK_ID_GROUND);
+ return 0;
+}
+
+static int mtk_musb_exit(struct musb *musb)
+{
+ struct device *dev = musb->controller;
+ struct mtk_glue *glue = dev_get_drvdata(dev->parent);
+
+ phy_power_off(glue->phy);
+ phy_exit(glue->phy);
+ mtk_musb_clks_disable(glue);
+
+ pm_runtime_put_sync(dev);
+ pm_runtime_disable(dev);
+ return 0;
+}
+
+static const struct musb_platform_ops mtk_musb_ops = {
+ .quirks = MUSB_DMA_INVENTRA,
+ .init = mtk_musb_init,
+ .get_toggle = mtk_musb_get_toggle,
+ .set_toggle = mtk_musb_set_toggle,
+ .exit = mtk_musb_exit,
+#ifdef CONFIG_USB_INVENTRA_DMA
+ .dma_init = musbhs_dma_controller_create_noirq,
+ .dma_exit = musbhs_dma_controller_destroy,
+#endif
+ .clearb = mtk_musb_clearb,
+ .clearw = mtk_musb_clearw,
+ .busctl_offset = mtk_musb_busctl_offset,
+ .set_mode = mtk_musb_set_mode,
+ .set_vbus = mtk_musb_set_vbus,
+};
+
+#define MTK_MUSB_MAX_EP_NUM 8
+#define MTK_MUSB_RAM_BITS 11
+
+static struct musb_fifo_cfg mtk_musb_mode_cfg[] = {
+ { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, },
+ { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, },
+ { .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, },
+ { .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, },
+ { .hw_ep_num = 3, .style = FIFO_TX, .maxpacket = 512, },
+ { .hw_ep_num = 3, .style = FIFO_RX, .maxpacket = 512, },
+ { .hw_ep_num = 4, .style = FIFO_TX, .maxpacket = 512, },
+ { .hw_ep_num = 4, .style = FIFO_RX, .maxpacket = 512, },
+ { .hw_ep_num = 5, .style = FIFO_TX, .maxpacket = 512, },
+ { .hw_ep_num = 5, .style = FIFO_RX, .maxpacket = 512, },
+ { .hw_ep_num = 6, .style = FIFO_TX, .maxpacket = 1024, },
+ { .hw_ep_num = 6, .style = FIFO_RX, .maxpacket = 1024, },
+ { .hw_ep_num = 7, .style = FIFO_TX, .maxpacket = 512, },
+ { .hw_ep_num = 7, .style = FIFO_RX, .maxpacket = 64, },
+};
+
+static const struct musb_hdrc_config mtk_musb_hdrc_config = {
+ .fifo_cfg = mtk_musb_mode_cfg,
+ .fifo_cfg_size = ARRAY_SIZE(mtk_musb_mode_cfg),
+ .multipoint = true,
+ .dyn_fifo = true,
+ .num_eps = MTK_MUSB_MAX_EP_NUM,
+ .ram_bits = MTK_MUSB_RAM_BITS,
+};
+
+static const struct platform_device_info mtk_dev_info = {
+ .name = "musb-hdrc",
+ .id = PLATFORM_DEVID_AUTO,
+ .dma_mask = DMA_BIT_MASK(32),
+};
+
+static int mtk_musb_probe(struct platform_device *pdev)
+{
+ struct musb_hdrc_platform_data *pdata;
+ struct mtk_glue *glue;
+ struct platform_device_info pinfo;
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct device_node *child, *extcon_node;
+ int ret = -ENOMEM;
+
+ glue = devm_kzalloc(dev, sizeof(*glue), GFP_KERNEL);
+ if (!glue)
+ return -ENOMEM;
+
+ glue->dev = dev;
+ pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return -ENOMEM;
+
+ ret = mtk_musb_clks_get(glue);
+ if (ret)
+ return ret;
+
+ pdata->config = &mtk_musb_hdrc_config;
+ pdata->platform_ops = &mtk_musb_ops;
+
+ glue->vbus = devm_regulator_get(dev, "vbus");
+ if (IS_ERR(glue->vbus)) {
+ dev_err(dev, "fail to get vbus\n");
+ return PTR_ERR(glue->vbus);
+ }
+
+ child = of_get_child_by_name(np, "connector");
+ if (!child) {
+ dev_err(dev, "failed to find usb connector node\n");
+ return ERR_PTR(-ENODEV);
+ }
+
+ extcon_node = of_parse_phandle(child, "extcon", 0);
+ if (!extcon_node) {
+ dev_err(dev, "failed to get extcon phandle");
+ return ERR_PTR(-ENODEV);
+ }
+
+ glue->edev = extcon_find_edev_by_node(extcon_node);
+ if (IS_ERR(glue->edev)) {
+ dev_err(dev, "fail to get extcon\n");
+ return PTR_ERR(glue->edev);
+ }
+
+ pdata->mode = usb_get_dr_mode(dev);
+ switch (pdata->mode) {
+ case USB_DR_MODE_HOST:
+ glue->phy_mode = PHY_MODE_USB_HOST;
+ break;
+ case USB_DR_MODE_PERIPHERAL:
+ glue->phy_mode = PHY_MODE_USB_DEVICE;
+ break;
+ default:
+ pdata->mode = USB_DR_MODE_OTG;
+ /* FALL THROUGH */
+ case USB_DR_MODE_OTG:
+ glue->phy_mode = PHY_MODE_USB_OTG;
+ break;
+ }
+
+ glue->phy = devm_of_phy_get_by_index(dev, np, 0);
+ if (IS_ERR(glue->phy)) {
+ dev_err(dev, "fail to getting phy %ld\n",
+ PTR_ERR(glue->phy));
+ return PTR_ERR(glue->phy);
+ }
+
+ glue->usb_phy = usb_phy_generic_register();
+ if (IS_ERR(glue->usb_phy)) {
+ dev_err(dev, "fail to registering usb-phy %ld\n",
+ PTR_ERR(glue->usb_phy));
+ return PTR_ERR(glue->usb_phy);
+ }
+
+ glue->xceiv = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
+ if (IS_ERR(glue->xceiv)) {
+ dev_err(dev, "fail to getting usb-phy %d\n", ret);
+ ret = PTR_ERR(glue->xceiv);
+ goto err_unregister_usb_phy;
+ }
+
+ platform_set_drvdata(pdev, glue);
+ pm_runtime_enable(dev);
+ pm_runtime_get_sync(dev);
+
+ ret = mtk_musb_clks_enable(glue);
+ if (ret)
+ goto err_enable_clk;
+
+ pinfo = mtk_dev_info;
+ pinfo.parent = dev;
+ pinfo.res = pdev->resource;
+ pinfo.num_res = pdev->num_resources;
+ pinfo.data = pdata;
+ pinfo.size_data = sizeof(*pdata);
+
+ glue->musb_pdev = platform_device_register_full(&pinfo);
+ if (IS_ERR(glue->musb_pdev)) {
+ ret = PTR_ERR(glue->musb_pdev);
+ dev_err(dev, "failed to register musb device: %d\n", ret);
+ goto err_device_register;
+ }
+
+ if (pdata->mode == USB_DR_MODE_OTG)
+ mtk_otg_switch_init(glue);
+
+ return 0;
+
+err_device_register:
+ mtk_musb_clks_disable(glue);
+err_enable_clk:
+ pm_runtime_put_sync(dev);
+ pm_runtime_disable(dev);
+err_unregister_usb_phy:
+ usb_phy_generic_unregister(glue->usb_phy);
+ return ret;
+}
+
+static int mtk_musb_remove(struct platform_device *pdev)
+{
+ struct mtk_glue *glue = platform_get_drvdata(pdev);
+ struct platform_device *usb_phy = glue->usb_phy;
+
+ platform_device_unregister(glue->musb_pdev);
+ usb_phy_generic_unregister(usb_phy);
+
+ return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id mtk_musb_match[] = {
+ {.compatible = "mediatek,mtk-musb",},
+ {},
+};
+MODULE_DEVICE_TABLE(of, mtk_musb_match);
+#endif
+
+static struct platform_driver mtk_musb_driver = {
+ .probe = mtk_musb_probe,
+ .remove = mtk_musb_remove,
+ .driver = {
+ .name = "musb-mtk",
+ .of_match_table = of_match_ptr(mtk_musb_match),
+ },
+};
+
+module_platform_driver(mtk_musb_driver);
+
+MODULE_DESCRIPTION("MediaTek MUSB Glue Layer");
+MODULE_AUTHOR("Min Guo <min.guo@mediatek.com>");
+MODULE_LICENSE("GPL v2");
--
1.9.1