From: michael.kao <michael.kao-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
To: michael.kao-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org,
fan.chen-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org,
jamesjj.liao-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org,
dawei.chien-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org,
louis.yu-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org,
roger.lu-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org,
Zhang Rui <rui.zhang-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>,
Eduardo Valentin
<edubezval-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
Daniel Lezcano
<daniel.lezcano-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>,
Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>,
Matthias Brugger
<matthias.bgg-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-mediatek-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-pm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: [PATCH 1/8] arm64: dts: mt8183: add thermal zone node
Date: Thu, 2 May 2019 18:43:08 +0800 [thread overview]
Message-ID: <1556793795-25204-2-git-send-email-michael.kao@mediatek.com> (raw)
In-Reply-To: <1556793795-25204-1-git-send-email-michael.kao-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
Add thermal zone node to Mediatek MT8183 dts file.
Signed-off-by: Michael Kao <michael.kao-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
---
arch/arm64/boot/dts/mediatek/mt8183.dtsi | 64 ++++++++++++++++++++++++++++++++
1 file changed, 64 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
index 926df75..b92116f 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
@@ -334,6 +334,67 @@
status = "disabled";
};
+ thermal: thermal@1100b000 {
+ #thermal-sensor-cells = <1>;
+ compatible = "mediatek,mt8183-thermal";
+ reg = <0 0x1100b000 0 0x1000>;
+ interrupts = <0 76 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_THERM>,
+ <&infracfg CLK_INFRA_AUXADC>;
+ clock-names = "therm", "auxadc";
+ resets = <&infracfg MT8183_INFRACFG_AO_THERM_SW_RST>;
+ mediatek,auxadc = <&auxadc>;
+ mediatek,apmixedsys = <&apmixedsys>;
+ mediatek,hw-reset-temp = <117000>;
+ nvmem-cells = <&thermal_calibration>;
+ nvmem-cell-names = "calibration-data";
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu_thermal {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&thermal 0>;
+ sustainable-power = <1500>;
+ };
+
+ tzts1: tzts1 {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+ thermal-sensors = <&thermal 1>;
+ };
+
+ tzts2: tzts2 {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+ thermal-sensors = <&thermal 2>;
+ };
+
+ tzts3: tzts3 {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+ thermal-sensors = <&thermal 3>;
+ };
+
+ tzts4: tzts4 {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+ thermal-sensors = <&thermal 4>;
+ };
+
+ tzts5: tzts5 {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+ thermal-sensors = <&thermal 5>;
+ };
+
+ tztsABB: tztsABB {
+ polling-delay-passive = <1000>;
+ polling-delay = <1000>;
+ thermal-sensors = <&thermal 6>;
+ };
+ };
audiosys: syscon@11220000 {
compatible = "mediatek,mt8183-audiosys", "syscon";
reg = <0 0x11220000 0 0x1000>;
@@ -368,6 +429,9 @@
compatible = "mediatek,mt8183-efuse",
"mediatek,efuse";
reg = <0 0x11f10000 0 0x1000>;
+ thermal_calibration: calib@180 {
+ reg = <0x180 0xc>;
+ };
};
mfgcfg: syscon@13000000 {
--
1.9.1
next prev parent reply other threads:[~2019-05-02 10:43 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-02 10:43 [PATCH 0/8] Add Mediatek thermal dirver and dtsi michael.kao
2019-05-02 10:43 ` [PATCH 2/8] arm64: dts: mt8183: add/update dynamic power coefficients michael.kao
2019-05-03 7:16 ` Hsin-Yi Wang
2019-05-08 12:27 ` Michael Kao
2019-05-02 10:43 ` [PATCH 3/8] arm64: dts: mt8183: Add #cooling-cells to CPU nodes michael.kao
2019-05-06 5:25 ` Eddie Huang
2019-05-08 12:29 ` Michael Kao
2019-05-02 10:43 ` [PATCH 4/8] arm64: dts: mt8183: Configure CPU cooling michael.kao
2019-05-07 8:57 ` Hsin-Yi Wang
2019-05-02 10:43 ` [PATCH 5/8] arm64: dts: mt8183: Increase polling frequency for CPU thermal zone michael.kao
2019-05-07 8:58 ` Hsin-Yi Wang
[not found] ` <1556793795-25204-1-git-send-email-michael.kao-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
2019-05-02 10:43 ` michael.kao [this message]
2019-05-03 8:03 ` [PATCH 1/8] arm64: dts: mt8183: add thermal zone node Hsin-Yi Wang
2019-05-03 16:46 ` Matthias Kaehlcke
2019-05-06 10:43 ` Daniel Lezcano
2019-05-08 12:23 ` Michael Kao
2019-05-10 8:14 ` Daniel Lezcano
2019-05-10 10:52 ` Michael Kao
2019-05-06 9:43 ` Daniel Lezcano
2019-05-02 10:43 ` [PATCH 6/8] thermal: mediatek: mt8183: fix bank number settings michael.kao
2019-05-07 8:58 ` Hsin-Yi Wang
2019-05-02 10:43 ` [PATCH 7/8] thermal: mediatek: add another get_temp ops for thermal sensors michael.kao
2019-05-11 2:31 ` Nicolas Boichat
2019-05-02 10:43 ` [PATCH 8/8] thermal: mediatek: use spinlock to protect PTPCORESEL michael.kao
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1556793795-25204-2-git-send-email-michael.kao@mediatek.com \
--to=michael.kao-nus5lvnupcjwk0htik3j/w@public.gmane.org \
--cc=daniel.lezcano-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
--cc=dawei.chien-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=edubezval-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=fan.chen-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org \
--cc=jamesjj.liao-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-mediatek-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-pm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=louis.yu-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=matthias.bgg-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=roger.lu-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org \
--cc=rui.zhang-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox