[PATCH v5 0/8] Bluetooth: Add MediaTek MT7927 (MT6639) support

[PATCH v5 0/8] Bluetooth: Add MediaTek MT7927 (MT6639) support

[Javier Tia]

Add Bluetooth support for the MediaTek MT7927 (Filogic 380), a PCIe
combo WiFi 7 + BT 5.4 module. The BT subsystem uses hardware variant
0x6639 and connects via USB.

The MT7927 is shipping in motherboards and PCIe add-in cards from ASUS,
Gigabyte, Lenovo, MSI, and TP-Link since mid-2024. Without these patches,
users see "Unsupported hardware variant (00006639)" or the BT subsystem
hangs during firmware download.

The series consists of eight patches:

  [1/8] Bluetooth: btmtk: Add MT6639 (MT7927) Bluetooth support
  [2/8] Bluetooth: btmtk: fix ISO interface setup for single alt setting
  [3/8] Bluetooth: btusb: Add MT7927 ID for ASUS ROG Crosshair X870E Hero
  [4/8] Bluetooth: btusb: Add MT7927 ID for Lenovo Legion Pro 7 16ARX9
  [5/8] Bluetooth: btusb: Add MT7927 ID for Gigabyte Z790 AORUS MASTER X
  [6/8] Bluetooth: btusb: Add MT7927 ID for MSI X870E Ace Max
  [7/8] Bluetooth: btusb: Add MT7927 ID for TP-Link Archer TBE550E
  [8/8] Bluetooth: btusb: Add MT7927 ID for ASUS X870E / ProArt X870E-Creator

Three driver changes are needed for MT6639 (patch 1):

1. CHIPID workaround: On some boards the BT USB MMIO register reads
   0x0000 for dev_id. Force dev_id to 0x6639 only when the USB VID/PID
   matches a known MT6639 device, avoiding misdetection if a future
   chip also reads zero. This follows the WiFi-side pattern.

2. Firmware naming: MT6639 uses firmware version prefix "2_1" instead of
   "1_1" used by MT7925 and other variants. The firmware path is
   mediatek/mt7927/BT_RAM_CODE_MT6639_2_1_hdr.bin, using the mt7927
   directory to match the WiFi firmware convention. The filename will
   likely change to use MT7927 once MediaTek submits a dedicated
   Linux firmware binary.

3. Section filtering: The firmware binary contains 9 sections, but only
   sections with (dlmodecrctype & 0xff) == 0x01 are Bluetooth-related.
   Sending WiFi/other sections causes an irreversible BT subsystem hang.

Patch 2 fixes the ISO interface setup for devices that expose only a
single alternate setting (alt 0) on the ISO endpoint. Without this fix,
btmtk_usb_claim_iso_intf() fails with EINVAL, causing ~20 second
initialization delays on 13d3:3588 devices.

WBS (Wideband Speech) was verified on MT7927 hardware. The controller
reports LMP_TRANSPARENT, LMP_ERR_DATA_REPORTING, and mSBC codec support.
A btmon capture confirms eSCO links establish with Transparent air mode
(mSBC) and 60-byte frames. BTUSB_WIDEBAND_SPEECH is correct for this
controller family.

Tested on:
- ASUS ROG Crosshair X870E Hero (USB 0489:e13a)
- ASUS ROG STRIX X870E-E (USB 13d3:3588)
- ASUS ROG STRIX B850-E GAMING WIFI (USB 0489:e13a)
- Gigabyte Z790 AORUS MASTER X (USB 0489:e10f)
- Lenovo Legion Pro 7 16ARX9 (USB 0489:e0fa)

Changes in v5:
- Fix patch 8/8 commit message: the ~19 second delay note was misleading
  since patch 2/8 already fixes that issue. Updated to clarify the
  relationship between the two patches (suggested by Luiz Augusto von
  Dentz)

Link to v4: https://lore.kernel.org/linux-bluetooth/20260330-mt7927-bt-support-v4-0-cecc025e7062@jetm.me/

Signed-off-by: Javier Tia <floss@jetm.me>
---
Javier Tia (8):
      Bluetooth: btmtk: Add MT6639 (MT7927) Bluetooth support
      Bluetooth: btmtk: fix ISO interface setup for single alt setting
      Bluetooth: btusb: Add MT7927 ID for ASUS ROG Crosshair X870E Hero
      Bluetooth: btusb: Add MT7927 ID for Lenovo Legion Pro 7 16ARX9
      Bluetooth: btusb: Add MT7927 ID for Gigabyte Z790 AORUS MASTER X
      Bluetooth: btusb: Add MT7927 ID for MSI X870E Ace Max
      Bluetooth: btusb: Add MT7927 ID for TP-Link Archer TBE550E
      Bluetooth: btusb: Add MT7927 ID for ASUS X870E / ProArt X870E-Creator

 drivers/bluetooth/btmtk.c     | 63 ++++++++++++++++++++++++++++++++++++++-----
 drivers/bluetooth/btmtk.h     |  7 +++--
 drivers/bluetooth/btmtksdio.c |  2 +-
 drivers/bluetooth/btusb.c     | 12 +++++++++
 4 files changed, 75 insertions(+), 9 deletions(-)
---
base-commit: 7f9446b23ac77f46d356b354ea8da49113e8000d
change-id: 20260305-mt7927-bt-support-6589a50c961f

Best regards,
--  
Javier Tia <floss@jetm.me>

[PATCH v5 1/8] Bluetooth: btmtk: Add MT6639 (MT7927) Bluetooth support

[Javier Tia]

The MediaTek MT7927 (Filogic 380) combo WiFi 7 + BT 5.4 module uses
hardware variant 0x6639 for its Bluetooth subsystem. Without this patch,
the chip fails with "Unsupported hardware variant (00006639)" or hangs
during firmware download.

Three changes are needed to support MT6639:

1. CHIPID workaround: On some boards the BT USB MMIO register reads
   0x0000 for dev_id, causing the driver to skip the 0x6639 init path.
   Force dev_id to 0x6639 only when the USB VID/PID matches a known
   MT6639 device, avoiding misdetection if a future chip also reads
   zero. This follows the WiFi-side pattern that uses PCI device IDs
   to scope the same workaround.

2. Firmware naming: MT6639 uses firmware version prefix "2_1" instead of
   "1_1" used by MT7925 and other variants. The firmware path is
   mediatek/mt7927/BT_RAM_CODE_MT6639_2_1_hdr.bin, using the mt7927
   directory to match the WiFi firmware convention. The filename will
   likely change to use MT7927 once MediaTek submits a dedicated
   Linux firmware binary.

3. Section filtering: The MT6639 firmware binary contains 9 sections, but
   only sections with (dlmodecrctype & 0xff) == 0x01 are Bluetooth-related.
   Sending the remaining WiFi/other sections causes an irreversible BT
   subsystem hang requiring a full power cycle. This matches the Windows
   driver behavior observed via USB captures.

Also add 0x6639 to the reset register (CONNV3) and firmware setup switch
cases alongside the existing 0x7925 handling.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Reported-by: Ryan Gilbert <xelnaga@gmail.com>
Signed-off-by: Javier Tia <floss@jetm.me>
---
 drivers/bluetooth/btmtk.c     | 60 +++++++++++++++++++++++++++++++++++++++----
 drivers/bluetooth/btmtk.h     |  7 +++--
 drivers/bluetooth/btmtksdio.c |  2 +-
 3 files changed, 61 insertions(+), 8 deletions(-)

diff --git a/drivers/bluetooth/btmtk.c b/drivers/bluetooth/btmtk.c
index 2507d587f28a..4af19b86c551 100644
--- a/drivers/bluetooth/btmtk.c
+++ b/drivers/bluetooth/btmtk.c
@@ -25,6 +25,22 @@
 /* It is for mt79xx iso data transmission setting */
 #define MTK_ISO_THRESHOLD	264
 
+/* Known MT6639 (MT7927) Bluetooth USB devices.
+ * Used to scope the zero-CHIPID workaround to real MT6639 hardware,
+ * since some boards return 0x0000 from the MMIO chip ID register.
+ */
+static const struct {
+	u16 vendor;
+	u16 product;
+} btmtk_mt6639_devs[] = {
+	{ 0x0489, 0xe13a },	/* ASUS ROG Crosshair X870E Hero */
+	{ 0x0489, 0xe0fa },	/* Lenovo Legion Pro 7 16ARX9 */
+	{ 0x0489, 0xe10f },	/* Gigabyte Z790 AORUS MASTER X */
+	{ 0x0489, 0xe110 },	/* MSI X870E Ace Max */
+	{ 0x0489, 0xe116 },	/* TP-Link Archer TBE550E */
+	{ 0x13d3, 0x3588 },	/* ASUS ROG STRIX X870E-E */
+};
+
 struct btmtk_patch_header {
 	u8 datetime[16];
 	u8 platform[4];
@@ -112,7 +128,11 @@ static void btmtk_coredump_notify(struct hci_dev *hdev, int state)
 void btmtk_fw_get_filename(char *buf, size_t size, u32 dev_id, u32 fw_ver,
 			   u32 fw_flavor)
 {
-	if (dev_id == 0x7925)
+	if (dev_id == 0x6639)
+		snprintf(buf, size,
+			 "mediatek/mt7927/BT_RAM_CODE_MT%04x_2_%x_hdr.bin",
+			 dev_id & 0xffff, (fw_ver & 0xff) + 1);
+	else if (dev_id == 0x7925)
 		snprintf(buf, size,
 			 "mediatek/mt%04x/BT_RAM_CODE_MT%04x_1_%x_hdr.bin",
 			 dev_id & 0xffff, dev_id & 0xffff, (fw_ver & 0xff) + 1);
@@ -128,7 +148,8 @@ void btmtk_fw_get_filename(char *buf, size_t size, u32 dev_id, u32 fw_ver,
 EXPORT_SYMBOL_GPL(btmtk_fw_get_filename);
 
 int btmtk_setup_firmware_79xx(struct hci_dev *hdev, const char *fwname,
-			      wmt_cmd_sync_func_t wmt_cmd_sync)
+			      wmt_cmd_sync_func_t wmt_cmd_sync,
+			      u32 dev_id)
 {
 	struct btmtk_hci_wmt_params wmt_params;
 	struct btmtk_patch_header *hdr;
@@ -166,6 +187,14 @@ int btmtk_setup_firmware_79xx(struct hci_dev *hdev, const char *fwname,
 		section_offset = le32_to_cpu(sectionmap->secoffset);
 		dl_size = le32_to_cpu(sectionmap->bin_info_spec.dlsize);
 
+		/* MT6639: only download sections where dlmode byte0 == 0x01,
+		 * matching the Windows driver behavior which skips WiFi/other
+		 * sections that would cause the chip to hang.
+		 */
+		if (dev_id == 0x6639 && dl_size > 0 &&
+		    (le32_to_cpu(sectionmap->bin_info_spec.dlmodecrctype) & 0xff) != 0x01)
+			continue;
+
 		if (dl_size > 0) {
 			retry = 20;
 			while (retry > 0) {
@@ -852,7 +881,7 @@ int btmtk_usb_subsys_reset(struct hci_dev *hdev, u32 dev_id)
 		if (err < 0)
 			return err;
 		msleep(100);
-	} else if (dev_id == 0x7925) {
+	} else if (dev_id == 0x7925 || dev_id == 0x6639) {
 		err = btmtk_usb_uhw_reg_read(hdev, MTK_BT_RESET_REG_CONNV3, &val);
 		if (err < 0)
 			return err;
@@ -938,7 +967,7 @@ int btmtk_usb_subsys_reset(struct hci_dev *hdev, u32 dev_id)
 	}
 
 	err = btmtk_usb_id_get(hdev, 0x70010200, &val);
-	if (err < 0 || !val)
+	if (err < 0 || (!val && dev_id != 0x6639))
 		bt_dev_err(hdev, "Can't get device id, subsys reset fail.");
 
 	return err;
@@ -1322,6 +1351,24 @@ int btmtk_usb_setup(struct hci_dev *hdev)
 		fw_flavor = (fw_flavor & 0x00000080) >> 7;
 	}
 
+	if (!dev_id) {
+		u16 vid = le16_to_cpu(btmtk_data->udev->descriptor.idVendor);
+		u16 pid = le16_to_cpu(btmtk_data->udev->descriptor.idProduct);
+		int i;
+
+		for (i = 0; i < ARRAY_SIZE(btmtk_mt6639_devs); i++) {
+			if (vid == btmtk_mt6639_devs[i].vendor &&
+			    pid == btmtk_mt6639_devs[i].product) {
+				dev_id = 0x6639;
+				break;
+			}
+		}
+
+		if (dev_id)
+			bt_dev_info(hdev, "MT6639: CHIPID=0x0000 with VID=%04x PID=%04x, using 0x6639",
+				    vid, pid);
+	}
+
 	btmtk_data->dev_id = dev_id;
 
 	err = btmtk_register_coredump(hdev, btmtk_data->drv_name, fw_version);
@@ -1339,11 +1386,13 @@ int btmtk_usb_setup(struct hci_dev *hdev)
 	case 0x7925:
 	case 0x7961:
 	case 0x7902:
+	case 0x6639:
 		btmtk_fw_get_filename(fw_bin_name, sizeof(fw_bin_name), dev_id,
 				      fw_version, fw_flavor);
 
 		err = btmtk_setup_firmware_79xx(hdev, fw_bin_name,
-						btmtk_usb_hci_wmt_sync);
+						btmtk_usb_hci_wmt_sync,
+						dev_id);
 		if (err < 0) {
 			/* retry once if setup firmware error */
 			if (!test_and_set_bit(BTMTK_FIRMWARE_DL_RETRY, &btmtk_data->flags))
@@ -1516,3 +1565,4 @@ MODULE_FIRMWARE(FIRMWARE_MT7668);
 MODULE_FIRMWARE(FIRMWARE_MT7922);
 MODULE_FIRMWARE(FIRMWARE_MT7961);
 MODULE_FIRMWARE(FIRMWARE_MT7925);
+MODULE_FIRMWARE(FIRMWARE_MT7927);
diff --git a/drivers/bluetooth/btmtk.h b/drivers/bluetooth/btmtk.h
index adaf385626ee..c564aedc0ce0 100644
--- a/drivers/bluetooth/btmtk.h
+++ b/drivers/bluetooth/btmtk.h
@@ -8,6 +8,7 @@
 #define FIRMWARE_MT7902		"mediatek/BT_RAM_CODE_MT7902_1_1_hdr.bin"
 #define FIRMWARE_MT7961		"mediatek/BT_RAM_CODE_MT7961_1_2_hdr.bin"
 #define FIRMWARE_MT7925		"mediatek/mt7925/BT_RAM_CODE_MT7925_1_1_hdr.bin"
+#define FIRMWARE_MT7927		"mediatek/mt7927/BT_RAM_CODE_MT6639_2_1_hdr.bin"
 
 #define HCI_EV_WMT 0xe4
 #define HCI_WMT_MAX_EVENT_SIZE		64
@@ -189,7 +190,8 @@ typedef int (*wmt_cmd_sync_func_t)(struct hci_dev *,
 int btmtk_set_bdaddr(struct hci_dev *hdev, const bdaddr_t *bdaddr);
 
 int btmtk_setup_firmware_79xx(struct hci_dev *hdev, const char *fwname,
-			      wmt_cmd_sync_func_t wmt_cmd_sync);
+			      wmt_cmd_sync_func_t wmt_cmd_sync,
+			      u32 dev_id);
 
 int btmtk_setup_firmware(struct hci_dev *hdev, const char *fwname,
 			 wmt_cmd_sync_func_t wmt_cmd_sync);
@@ -228,7 +230,8 @@ static inline int btmtk_set_bdaddr(struct hci_dev *hdev,
 
 static inline int btmtk_setup_firmware_79xx(struct hci_dev *hdev,
 					    const char *fwname,
-					    wmt_cmd_sync_func_t wmt_cmd_sync)
+					    wmt_cmd_sync_func_t wmt_cmd_sync,
+					    u32 dev_id)
 {
 	return -EOPNOTSUPP;
 }
diff --git a/drivers/bluetooth/btmtksdio.c b/drivers/bluetooth/btmtksdio.c
index 042064464d34..5b0fab7b89b5 100644
--- a/drivers/bluetooth/btmtksdio.c
+++ b/drivers/bluetooth/btmtksdio.c
@@ -883,7 +883,7 @@ static int mt79xx_setup(struct hci_dev *hdev, const char *fwname)
 	u8 param = 0x1;
 	int err;
 
-	err = btmtk_setup_firmware_79xx(hdev, fwname, mtk_hci_wmt_sync);
+	err = btmtk_setup_firmware_79xx(hdev, fwname, mtk_hci_wmt_sync, 0);
 	if (err < 0) {
 		bt_dev_err(hdev, "Failed to setup 79xx firmware (%d)", err);
 		return err;

-- 
2.53.0

[PATCH v5 2/8] Bluetooth: btmtk: fix ISO interface setup for single alt setting

[Javier Tia]

Some MT6639 Bluetooth USB interfaces (e.g. IMC Networks 13d3:3588 on
ASUS ROG STRIX X870E-E and ProArt X870E-Creator boards) expose only a
single alternate setting (alt 0) on the ISO interface. The driver
unconditionally requests alt setting 1, which fails with EINVAL on
these devices, causing a ~20 second initialization delay and no LE
audio support.

Check the number of available alternate settings before selecting one.
If only alt 0 exists, use it; otherwise request alt 1 as before.

Closes: https://github.com/jetm/mediatek-mt7927-dkms/pull/39
Signed-off-by: Javier Tia <floss@jetm.me>
Reported-by: Ryan Gilbert <xelnaga@gmail.com>
Tested-by: Ryan Gilbert <xelnaga@gmail.com>
---
 drivers/bluetooth/btmtk.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/bluetooth/btmtk.c b/drivers/bluetooth/btmtk.c
index 4af19b86c551..f8cff895f14c 100644
--- a/drivers/bluetooth/btmtk.c
+++ b/drivers/bluetooth/btmtk.c
@@ -1029,7 +1029,8 @@ static int __set_mtk_intr_interface(struct hci_dev *hdev)
 	if (!btmtk_data->isopkt_intf)
 		return -ENODEV;
 
-	err = usb_set_interface(btmtk_data->udev, MTK_ISO_IFNUM, 1);
+	err = usb_set_interface(btmtk_data->udev, MTK_ISO_IFNUM,
+			       (intf->num_altsetting > 1) ? 1 : 0);
 	if (err < 0) {
 		bt_dev_err(hdev, "setting interface failed (%d)", -err);
 		return err;

-- 
2.53.0

[PATCH v5 3/8] Bluetooth: btusb: Add MT7927 ID for ASUS ROG Crosshair X870E Hero

[Javier Tia]

Add USB device ID 0489:e13a (Foxconn/Hon Hai) for the MediaTek MT7927
(Filogic 380) Bluetooth interface found on the ASUS ROG Crosshair X870E
Hero WiFi motherboard.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e13a Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
...
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Jose Tiburcio Ribeiro Netto <jnetto@mineiro.io>
---
 drivers/bluetooth/btusb.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index a5e44887a5b5..58309af0f7a2 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -751,6 +751,8 @@ static const struct usb_device_id quirks_table[] = {
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe139), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0489, 0xe13a), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14e), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14f), .driver_info = BTUSB_MEDIATEK |

-- 
2.53.0

[PATCH v5 4/8] Bluetooth: btusb: Add MT7927 ID for Lenovo Legion Pro 7 16ARX9

[Javier Tia]

Add USB device ID 0489:e0fa (Foxconn/Hon Hai) for the MediaTek MT7927
(Filogic 380) Bluetooth interface found on the Lenovo Legion Pro 7
16ARX9 laptop.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0fa Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
...
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Llewellyn Curran <melinko2003@gmail.com>
---
 drivers/bluetooth/btusb.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 58309af0f7a2..2c9ca3d6016b 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -753,6 +753,8 @@ static const struct usb_device_id quirks_table[] = {
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe13a), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0489, 0xe0fa), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14e), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14f), .driver_info = BTUSB_MEDIATEK |

-- 
2.53.0

[PATCH v5 5/8] Bluetooth: btusb: Add MT7927 ID for Gigabyte Z790 AORUS MASTER X

[Javier Tia]

Add USB device ID 0489:e10f (Foxconn/Hon Hai) for the MediaTek MT7927
(Filogic 380) Bluetooth interface found on the Gigabyte Z790 AORUS
MASTER X motherboard.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e10f Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
...
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Chapuis Dario <chapuisdario4@gmail.com>
Tested-by: Evgeny Kapusta <3193631@gmail.com>
---
 drivers/bluetooth/btusb.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 2c9ca3d6016b..d60798331bb3 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -755,6 +755,8 @@ static const struct usb_device_id quirks_table[] = {
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe0fa), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0489, 0xe10f), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14e), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14f), .driver_info = BTUSB_MEDIATEK |

-- 
2.53.0

[PATCH v5 6/8] Bluetooth: btusb: Add MT7927 ID for MSI X870E Ace Max

[Javier Tia]

Add USB device ID 0489:e110 (Foxconn/Hon Hai) for the MediaTek MT7927
(Filogic 380) Bluetooth interface found on the MSI X870E Ace Max
motherboard.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e110 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
...
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Nitin Gurram <nitin.reddy88@gmail.com>
---
 drivers/bluetooth/btusb.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index d60798331bb3..96882e9b831c 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -757,6 +757,8 @@ static const struct usb_device_id quirks_table[] = {
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe10f), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0489, 0xe110), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14e), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14f), .driver_info = BTUSB_MEDIATEK |

-- 
2.53.0

[PATCH v5 7/8] Bluetooth: btusb: Add MT7927 ID for TP-Link Archer TBE550E

[Javier Tia]

Add USB device ID 0489:e116 (Foxconn/Hon Hai) for the MediaTek MT7927
(Filogic 380) Bluetooth interface found on the TP-Link Archer TBE550E
PCIe adapter.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e116 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
...
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Thibaut FRANCOIS <tibo@humeurlibre.fr>
---
 drivers/bluetooth/btusb.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 96882e9b831c..55a000540439 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -759,6 +759,8 @@ static const struct usb_device_id quirks_table[] = {
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe110), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0489, 0xe116), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14e), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14f), .driver_info = BTUSB_MEDIATEK |

-- 
2.53.0

[PATCH v5 8/8] Bluetooth: btusb: Add MT7927 ID for ASUS X870E / ProArt X870E-Creator

[Javier Tia]

Add USB device ID 13d3:3588 (IMC Networks/Azurewave) for the MediaTek
MT7927 (Filogic 380) Bluetooth interface found on the ASUS ROG STRIX
X870E-E GAMING WIFI and ASUS ProArt X870E-Creator WiFi motherboards.

Note: boards with this USB ID expose only one ISO alternate setting
(alt 0). Without the fix in patch 2/8 ("btmtk: fix ISO interface
setup for single alt setting"), this caused ~19 second initialization
delays. With the fix applied, initialization completes in ~2.6
seconds.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3588 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
Link: https://github.com/openwrt/mt76/issues/927
Signed-off-by: Javier Tia <floss@jetm.me>
Tested-by: Jose Tiburcio Ribeiro Netto <jnetto@mineiro.io>
Tested-by: Ivan Lubnin <lubnin.ivan@gmail.com>
---
 drivers/bluetooth/btusb.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 55a000540439..45ef0d008bce 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -761,6 +761,8 @@ static const struct usb_device_id quirks_table[] = {
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe116), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x13d3, 0x3588), .driver_info = BTUSB_MEDIATEK |
+						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14e), .driver_info = BTUSB_MEDIATEK |
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x0489, 0xe14f), .driver_info = BTUSB_MEDIATEK |

-- 
2.53.0

Re: [PATCH v5 8/8] Bluetooth: btusb: Add MT7927 ID for ASUS X870E / ProArt X870E-Creator

[Paul Menzel]

Dear Javier,


Thank you for the patches and your persistence on improving them. I 
noticed one more thing, just in this one:

Am 31.03.26 um 19:09 schrieb Javier Tia:
> Add USB device ID 13d3:3588 (IMC Networks/Azurewave) for the MediaTek
> MT7927 (Filogic 380) Bluetooth interface found on the ASUS ROG STRIX
> X870E-E GAMING WIFI and ASUS ProArt X870E-Creator WiFi motherboards.
> 
> Note: boards with this USB ID expose only one ISO alternate setting
> (alt 0). Without the fix in patch 2/8 ("btmtk: fix ISO interface
> setup for single alt setting"), this caused ~19 second initialization
> delays. With the fix applied, initialization completes in ~2.6
> seconds.
> 
> The information in /sys/kernel/debug/usb/devices about the Bluetooth
> device is listed as the below.
> 
> T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  5 Spd=480  MxCh= 0
> D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
> P:  Vendor=13d3 ProdID=3588 Rev= 1.00
> S:  Manufacturer=MediaTek Inc.
> S:  Product=Wireless_Device
> S:  SerialNumber=000000000
> C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
> A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
> I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
> E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
> I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
> E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
> E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
> 
> Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096
> Link: https://github.com/openwrt/mt76/issues/927
> Signed-off-by: Javier Tia <floss@jetm.me>
> Tested-by: Jose Tiburcio Ribeiro Netto <jnetto@mineiro.io>
> Tested-by: Ivan Lubnin <lubnin.ivan@gmail.com>
> ---
>   drivers/bluetooth/btusb.c | 2 ++
>   1 file changed, 2 insertions(+)
> 
> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
> index 55a000540439..45ef0d008bce 100644
> --- a/drivers/bluetooth/btusb.c
> +++ b/drivers/bluetooth/btusb.c
> @@ -761,6 +761,8 @@ static const struct usb_device_id quirks_table[] = {
>   						     BTUSB_WIDEBAND_SPEECH },
>   	{ USB_DEVICE(0x0489, 0xe116), .driver_info = BTUSB_MEDIATEK |
>   						     BTUSB_WIDEBAND_SPEECH },
> +	{ USB_DEVICE(0x13d3, 0x3588), .driver_info = BTUSB_MEDIATEK |
> +						     BTUSB_WIDEBAND_SPEECH },

This is not sorted. Is there a reason to place it here?

>   	{ USB_DEVICE(0x0489, 0xe14e), .driver_info = BTUSB_MEDIATEK |
>   						     BTUSB_WIDEBAND_SPEECH },
>   	{ USB_DEVICE(0x0489, 0xe14f), .driver_info = BTUSB_MEDIATEK |
> 


Kind regards,

Paul

Re: [PATCH v5 0/8] Bluetooth: Add MediaTek MT7927 (MT6639) support

[patchwork-bot+bluetooth]

Hello:

This series was applied to bluetooth/bluetooth-next.git (master)
by Luiz Augusto von Dentz <luiz.von.dentz@intel.com>:

On Tue, 31 Mar 2026 11:09:30 -0600 you wrote:
> Add Bluetooth support for the MediaTek MT7927 (Filogic 380), a PCIe
> combo WiFi 7 + BT 5.4 module. The BT subsystem uses hardware variant
> 0x6639 and connects via USB.
> 
> The MT7927 is shipping in motherboards and PCIe add-in cards from ASUS,
> Gigabyte, Lenovo, MSI, and TP-Link since mid-2024. Without these patches,
> users see "Unsupported hardware variant (00006639)" or the BT subsystem
> hangs during firmware download.
> 
> [...]

Here is the summary with links:
  - [v5,1/8] Bluetooth: btmtk: Add MT6639 (MT7927) Bluetooth support
    https://git.kernel.org/bluetooth/bluetooth-next/c/2e16247422fb
  - [v5,2/8] Bluetooth: btmtk: fix ISO interface setup for single alt setting
    https://git.kernel.org/bluetooth/bluetooth-next/c/798c2ba5006c
  - [v5,3/8] Bluetooth: btusb: Add MT7927 ID for ASUS ROG Crosshair X870E Hero
    https://git.kernel.org/bluetooth/bluetooth-next/c/3e148151bc75
  - [v5,4/8] Bluetooth: btusb: Add MT7927 ID for Lenovo Legion Pro 7 16ARX9
    https://git.kernel.org/bluetooth/bluetooth-next/c/fa528d431d10
  - [v5,5/8] Bluetooth: btusb: Add MT7927 ID for Gigabyte Z790 AORUS MASTER X
    https://git.kernel.org/bluetooth/bluetooth-next/c/a4a3b78a8b3d
  - [v5,6/8] Bluetooth: btusb: Add MT7927 ID for MSI X870E Ace Max
    https://git.kernel.org/bluetooth/bluetooth-next/c/b8185eff87a7
  - [v5,7/8] Bluetooth: btusb: Add MT7927 ID for TP-Link Archer TBE550E
    https://git.kernel.org/bluetooth/bluetooth-next/c/54834ec3a5b0
  - [v5,8/8] Bluetooth: btusb: Add MT7927 ID for ASUS X870E / ProArt X870E-Creator
    https://git.kernel.org/bluetooth/bluetooth-next/c/b816ef8a31b7

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html