From: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
To: honghui.zhang@mediatek.com
Cc: marc.zyngier@arm.com, bhelgaas@google.com,
matthias.bgg@gmail.com, linux-arm-kernel@lists.infradead.org,
linux-mediatek@lists.infradead.org, linux-pci@vger.kernel.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
yingjoe.chen@mediatek.com, eddie.huang@mediatek.com,
ryder.lee@mediatek.com, ulf.hansson@linaro.org,
hongkun.cao@mediatek.com, youlin.pei@mediatek.com,
yong.wu@mediatek.com, yt.shen@mediatek.com,
sean.wang@mediatek.com, xinping.qian@mediatek.com
Subject: Re: [PATCH v4 2/4] PCI: mediatek: enable msi after clock enabled
Date: Fri, 21 Sep 2018 17:46:12 +0100 [thread overview]
Message-ID: <20180921164612.GA27651@e107981-ln.cambridge.arm.com> (raw)
In-Reply-To: <1536573023-6720-3-git-send-email-honghui.zhang@mediatek.com>
On Mon, Sep 10, 2018 at 05:50:21PM +0800, honghui.zhang@mediatek.com wrote:
> From: Honghui Zhang <honghui.zhang@mediatek.com>
>
> The clocks was not enabled when enable MSI. This patch fix this
> issue by calling mtk_pcie_enable_msi in mtk_pcie_startup_port_v2
> since the clock was all enabled at that time.
>
> The function of mtk_pcie_startup_port_v2's define location is
> re-arranged to avoid mtk_pcie_enable_msi's forward declaration.
>
> Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
> Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
> ---
> drivers/pci/controller/pcie-mediatek.c | 143 +++++++++++++++++----------------
> 1 file changed, 72 insertions(+), 71 deletions(-)
Can you read:
https://marc.info/?l=linux-pci&m=150905742808166&w=2
follow it and adapt this patch and the others accordingly please ?
Thanks,
Lorenzo
> diff --git a/drivers/pci/controller/pcie-mediatek.c b/drivers/pci/controller/pcie-mediatek.c
> index 20b9088..5aba43a 100644
> --- a/drivers/pci/controller/pcie-mediatek.c
> +++ b/drivers/pci/controller/pcie-mediatek.c
> @@ -398,75 +398,6 @@ static struct pci_ops mtk_pcie_ops_v2 = {
> .write = mtk_pcie_config_write,
> };
>
> -static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
> -{
> - struct mtk_pcie *pcie = port->pcie;
> - struct resource *mem = &pcie->mem;
> - const struct mtk_pcie_soc *soc = port->pcie->soc;
> - u32 val;
> - size_t size;
> - int err;
> -
> - /* MT7622 platforms need to enable LTSSM and ASPM from PCIe subsys */
> - if (pcie->base) {
> - val = readl(pcie->base + PCIE_SYS_CFG_V2);
> - val |= PCIE_CSR_LTSSM_EN(port->slot) |
> - PCIE_CSR_ASPM_L1_EN(port->slot);
> - writel(val, pcie->base + PCIE_SYS_CFG_V2);
> - }
> -
> - /* Assert all reset signals */
> - writel(0, port->base + PCIE_RST_CTRL);
> -
> - /*
> - * Enable PCIe link down reset, if link status changed from link up to
> - * link down, this will reset MAC control registers and configuration
> - * space.
> - */
> - writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL);
> -
> - /* De-assert PHY, PE, PIPE, MAC and configuration reset */
> - val = readl(port->base + PCIE_RST_CTRL);
> - val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB |
> - PCIE_MAC_SRSTB | PCIE_CRSTB;
> - writel(val, port->base + PCIE_RST_CTRL);
> -
> - /* Set up vendor ID and class code */
> - if (soc->need_fix_class_id) {
> - val = PCI_VENDOR_ID_MEDIATEK;
> - writew(val, port->base + PCIE_CONF_VEND_ID);
> -
> - val = PCI_CLASS_BRIDGE_HOST;
> - writew(val, port->base + PCIE_CONF_CLASS_ID);
> - }
> -
> - /* 100ms timeout value should be enough for Gen1/2 training */
> - err = readl_poll_timeout(port->base + PCIE_LINK_STATUS_V2, val,
> - !!(val & PCIE_PORT_LINKUP_V2), 20,
> - 100 * USEC_PER_MSEC);
> - if (err)
> - return -ETIMEDOUT;
> -
> - /* Set INTx mask */
> - val = readl(port->base + PCIE_INT_MASK);
> - val &= ~INTX_MASK;
> - writel(val, port->base + PCIE_INT_MASK);
> -
> - /* Set AHB to PCIe translation windows */
> - size = mem->end - mem->start;
> - val = lower_32_bits(mem->start) | AHB2PCIE_SIZE(fls(size));
> - writel(val, port->base + PCIE_AHB_TRANS_BASE0_L);
> -
> - val = upper_32_bits(mem->start);
> - writel(val, port->base + PCIE_AHB_TRANS_BASE0_H);
> -
> - /* Set PCIe to AXI translation memory space.*/
> - val = fls(0xffffffff) | WIN_ENABLE;
> - writel(val, port->base + PCIE_AXI_WINDOW0);
> -
> - return 0;
> -}
> -
> static void mtk_compose_msi_msg(struct irq_data *data, struct msi_msg *msg)
> {
> struct mtk_pcie_port *port = irq_data_get_irq_chip_data(data);
> @@ -643,8 +574,6 @@ static int mtk_pcie_init_irq_domain(struct mtk_pcie_port *port,
> ret = mtk_pcie_allocate_msi_domains(port);
> if (ret)
> return ret;
> -
> - mtk_pcie_enable_msi(port);
> }
>
> return 0;
> @@ -711,6 +640,78 @@ static int mtk_pcie_setup_irq(struct mtk_pcie_port *port,
> return 0;
> }
>
> +static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
> +{
> + struct mtk_pcie *pcie = port->pcie;
> + struct resource *mem = &pcie->mem;
> + const struct mtk_pcie_soc *soc = port->pcie->soc;
> + u32 val;
> + size_t size;
> + int err;
> +
> + /* MT7622 platforms need to enable LTSSM and ASPM from PCIe subsys */
> + if (pcie->base) {
> + val = readl(pcie->base + PCIE_SYS_CFG_V2);
> + val |= PCIE_CSR_LTSSM_EN(port->slot) |
> + PCIE_CSR_ASPM_L1_EN(port->slot);
> + writel(val, pcie->base + PCIE_SYS_CFG_V2);
> + }
> +
> + /* Assert all reset signals */
> + writel(0, port->base + PCIE_RST_CTRL);
> +
> + /*
> + * Enable PCIe link down reset, if link status changed from link up to
> + * link down, this will reset MAC control registers and configuration
> + * space.
> + */
> + writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL);
> +
> + /* De-assert PHY, PE, PIPE, MAC and configuration reset */
> + val = readl(port->base + PCIE_RST_CTRL);
> + val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB |
> + PCIE_MAC_SRSTB | PCIE_CRSTB;
> + writel(val, port->base + PCIE_RST_CTRL);
> +
> + /* Set up vendor ID and class code */
> + if (soc->need_fix_class_id) {
> + val = PCI_VENDOR_ID_MEDIATEK;
> + writew(val, port->base + PCIE_CONF_VEND_ID);
> +
> + val = PCI_CLASS_BRIDGE_HOST;
> + writew(val, port->base + PCIE_CONF_CLASS_ID);
> + }
> +
> + /* 100ms timeout value should be enough for Gen1/2 training */
> + err = readl_poll_timeout(port->base + PCIE_LINK_STATUS_V2, val,
> + !!(val & PCIE_PORT_LINKUP_V2), 20,
> + 100 * USEC_PER_MSEC);
> + if (err)
> + return -ETIMEDOUT;
> +
> + /* Set INTx mask */
> + val = readl(port->base + PCIE_INT_MASK);
> + val &= ~INTX_MASK;
> + writel(val, port->base + PCIE_INT_MASK);
> +
> + if (IS_ENABLED(CONFIG_PCI_MSI))
> + mtk_pcie_enable_msi(port);
> +
> + /* Set AHB to PCIe translation windows */
> + size = mem->end - mem->start;
> + val = lower_32_bits(mem->start) | AHB2PCIE_SIZE(fls(size));
> + writel(val, port->base + PCIE_AHB_TRANS_BASE0_L);
> +
> + val = upper_32_bits(mem->start);
> + writel(val, port->base + PCIE_AHB_TRANS_BASE0_H);
> +
> + /* Set PCIe to AXI translation memory space.*/
> + val = fls(0xffffffff) | WIN_ENABLE;
> + writel(val, port->base + PCIE_AXI_WINDOW0);
> +
> + return 0;
> +}
> +
> static void __iomem *mtk_pcie_map_bus(struct pci_bus *bus,
> unsigned int devfn, int where)
> {
> --
> 2.6.4
>
next prev parent reply other threads:[~2018-09-21 16:46 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-09-10 9:50 [PATCH v4 0/4] PCI: mediatek: fixup find_port, enable_msi and add pm, module support honghui.zhang
2018-09-10 9:50 ` [PATCH v4 1/4] PCI: mediatek: fixup mtk_pcie_find_port logical honghui.zhang
2018-09-21 16:07 ` Lorenzo Pieralisi
2018-09-26 9:06 ` Honghui Zhang
2018-09-10 9:50 ` [PATCH v4 2/4] PCI: mediatek: enable msi after clock enabled honghui.zhang
2018-09-21 16:46 ` Lorenzo Pieralisi [this message]
2018-09-26 9:08 ` Honghui Zhang
2018-09-10 9:50 ` [PATCH v4 3/4] PCI: mediatek: Add system pm support for MT2712 and MT7622 honghui.zhang
2018-09-10 9:50 ` [PATCH v4 4/4] PCI: mediatek: Add loadable kernel module support honghui.zhang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180921164612.GA27651@e107981-ln.cambridge.arm.com \
--to=lorenzo.pieralisi@arm.com \
--cc=bhelgaas@google.com \
--cc=devicetree@vger.kernel.org \
--cc=eddie.huang@mediatek.com \
--cc=honghui.zhang@mediatek.com \
--cc=hongkun.cao@mediatek.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-pci@vger.kernel.org \
--cc=marc.zyngier@arm.com \
--cc=matthias.bgg@gmail.com \
--cc=ryder.lee@mediatek.com \
--cc=sean.wang@mediatek.com \
--cc=ulf.hansson@linaro.org \
--cc=xinping.qian@mediatek.com \
--cc=yingjoe.chen@mediatek.com \
--cc=yong.wu@mediatek.com \
--cc=youlin.pei@mediatek.com \
--cc=yt.shen@mediatek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox